Geely Emgrand X7. Manual part - 97

 

  Главная      Geely     Geely Emgrand X7 - Manual

 

поиск по сайту            

 

 

 

 

 

 

 

 

 

 

 

 

 

содержание   ..   90  91  92  93  94  95  96  97  98  ..

 

 

Geely Emgrand X7. Manual part - 97

 

 

B056 

No key was stored 
in the anti-theft 
device 

Anti-theft controller 
has not matched 
with any key, and 
therefore no 
transponder ID is 
stored in it. 

Learn the key again. 

B057 

No security code 
has been set . 

New or reset 
anti-theft controller

Set the security code and match the 
anti-theft controller again. 

B059 

No electric injector 
controller request 
was received 

The anti-theft 
controller didn’t 
receive the 
communication 
request from the 
electric injector 
controller 

1.  Inspect the insertion of the 

harness connector of the 
anti-theft controller 

2.  Inspect the connection, open 

circuit or poor contact of the 
harness between the anti-theft 
controller terminal 5 and the 
ECM. 

3.  Replace the anti-theft controller 

and inspect the above 
mentioned faults. If no fault 
occurred, the fault can be 
deemed within the anti-theft 
controller; 

4.  Replace the ECM and inspect 

the above faults. If no fault 
occurred, the problem can be 
deemed as within the electric 
injector. 

B060 

The current key is 
not stored in the 
anti-theft device 

The transponder ID 
is not stored in the 
anti-theft controller

Use the scan tool to exert the “Key 
Learning” function 

B061 

Key is unable to be 
verified or the 
communication is 
disturbed. 

Communication 
between the 
transponder and the 
anti-theft controller 
can not be 
established or be 
disturbed. The 
communication 
data are abnormal. 
The electric injector 
and transponder 
have inconsistent 
key. 

1.  Inspect whether the EAS Coil is 

normal. 

2.  Inspect whether the transponder 

is new or unmatched. If so, 
match them again. 

3.  If the transponder is matched, 

confirm the exchanging of the 
transponder, or the exchanging 
and resetting of the electric 
injector. 

Note: DTC (DTC code) is set based on the above-mentioned output sequence. However, at the 
same time it only shows a maximum of 7 DTC. 

Note: DTC code history is code recorded before shown by the scan tool. If a DTC code has no 
historical features, it only shows the current status. If there are historical features, it can display 
the status up to 20 ignition cycles. 

387

2.5.7.5 Data Flow Table 

Serial Number 

Description 

Data 

Ignition Switch 0 

N/OFF 

2 Key 

Detection 

YES/NO 

3 Ever 

matched 

YES/NO 

The Current Key Position 

Not Programmed/Programmed

Key Storage Position 1 

Not Stored/Stored 

Key Storage Position 2 

Not Stored/Stored 

Key Storage Position 3 

Not Stored/Stored 

Key Storage Position 4 

Not Stored/Stored 

Key Storage Position 5 

Not Stored/Stored 

10 

Security Certification 

Not Passed/Passed 

11 Anti-theft 

Verification 

YES/NO 

12 

Vehicle Identification Number

Not Programmed/Programmed

13 Password 

Settings 

YES/NO 

14 Password 

Lock 

YES/NO 

15 Entering 

The 

Password 

YES/NO 

16 

Remaining Numbers Of Times 
Entering The Password 

10 

2.5.7.6 Fault Symptom Table 

Symptoms 

Suspected Parts 

Refer to Page 

Engine Anti-theft Indicator 
Always On 

Instrument Refer 

to 

11.6.7.1 Replacement 

of Combination Instrument 
Assembly. 

1. Key 

2. Anti-theft 

Coil 

3. Anti-theft 

Module 

4. ECM 

5. Instrument 

Engine Anti-theft warning 
lamp always on, the engine 
can not start. 

6. Wiring 

Harness 

Refer to 2.5.7.17 Engine 
Anti-theft Warning Lamp 
Flashing, Vehicle Can Not 
Start 

388

Connector 

1. Anti-theft 

Coil 

— 

Anti-theft system can not 
detect the valid key. 

2. Anti-theft 

Module 

— 

1. Anti-theft 

Coil 

— 

2. Anti-theft 

Module 

— 

Keys do not match 

3. Key 

— 

1. Wiring Harness and 

Connector 

2. Anti-theft 

Module 

ECM always detects Anti-theft 
malfunction 

3. ECM 

Refer to 2.5.7.17 Engine 
Anti-theft Warning Lamp 
Flashing, Vehicle Can Not 
Start 

389

2.5.7.7 Replaced Key Programming 

Measure VVT solenoid valve resistance. 

 

Turn the ignition switch to the position "ON". 

 

3 Enter 

Anti-theft 

System 

Note: Before enter the security code please contact the manufacturers technical department, as 
the Anti-theft computer will be locked after the wrong security code entered seven consecutive 
times. 

 

Enter the security code. 

 

5 Learn 

the 

key. 

 

6 Key 

Programming. 

 

Place the ignition switch at "OFF" position and wait about 5 min or so. 

 

New key learn successful. 

Next 

Next 

Next 

Next 

Next 

Next 

Next 

390

 

 

 

 

 

 

содержание   ..   90  91  92  93  94  95  96  97  98