Fiat Ulysse (2022 year). Manual in english - page 5

68

Ease of use and comfort

a risk of injury in the event of an accident or 
sudden braking.

Front door storage pockets

Liquids carried in an open vessel (e.g. a 
cup or mug) could be spilt, presenting a 

risk of damage on contact with the controls in 
the dashboard and centre console. Be 
careful.

Upper glove box

This is located in the dashboard, behind the 
steering wheel.

 

 

Press the control to open the lid (depending on 
version) then guide it to its fully open position.
To close it, guide the lid then press the centre 
gently.

Any liquid which could spill risks causing 

an electrical short circuit and therefore a 

potential fire.

"Aircraft" type tables

 

 

Fitted to the back of each front seat.

 

 

►  To use the table, lower it fully until it locks in 

the low position.

►  To stow it, raise the table to the high position, 

passing the point of resistance.

On the passenger side, do not forget to 
fold the table up before placing the seat 

in the "table" position.
Do not place hard or heavy objects on 
the table. They could become dangerous 
projectiles in the event of emergency braking 
or impact.

For more information on the 

Front seats

, 

and in particular placing the backrest in 

the "table" position, refer to the corresponding 
section.

12 V socket(s)

Depending on version.

 

 

 

 

 

 

14/02/2022   15:33:16

69

Ease of use and comfort

3

 

 

►  To connect a 12 V accessory (maximum 

power: 120 Watts), lift the cover and plug in a 
suitable adapter.

Observe the maximum power rating to 
avoid damaging the accessory.

The connection of an electrical device 
not approved by Fiat, such as a USB 

charger, may adversely affect the operation of 

vehicle electrical systems, causing faults such 
as poor radio reception or interference with 
displays in the screens.

USB socket

 

 

 

 

The socket can be used to connect a portable 
device or a USB memory stick.

The socket reads audio files that are sent to your 

audio system to be played through the vehicle's 
speakers.

These files can be managed using the steering-

mounted controls or those on the audio system.

The USB socket also allows a 
smartphone to be connected by 

Android Auto

®

 or CarPlay

®

, enabling certain 

smartphone applications to be used on the touch 
screen.
For best results, use a cable made or approved 
by the device manufacturer.
These applications can be managed using the 
steering-mounted controls or the audio system 
controls.

When the USB socket is used, the 
portable device charges automatically.

While charging, a message is displayed if the 
power drawn by the portable device exceeds 
the current supplied by the vehicle.

For more information about how to use this 
equipment, refer to the sections describing 
the audio and telematics systems.

220 V socket

 

 

Depending on version, a 220 V/50 Hz socket 
(maximum power: 120 W) is located underneath 
the front right-hand seat and therefore 
accessible from row 2.
This socket works with the engine running, as 
well as in STOP mode of Stop & Start. 

 

 

►  Lift the cover.

►  Check that the indicator lamp is on green.

►  Connect your multimedia or other electrical 

device (telephone charger, laptop computer, 
CD-DVD player, bottle warmer, etc.).

14/02/2022   15:33:17

70

Ease of use and comfort

In the event of a malfunction, the 

green indicator lamp flashes.

Have it checked by a Fiat Dealership or a 

qualified workshop.

Connect only one device to the socket at 
a time (do not use an extension lead or 

multi-socket) and only connect devices with 
Class II insulation (indicated on the device).
Do not use devices with metallic cases.

If the power consumption becomes too 
high and when required by the vehicle's 

electrical system (particular weather 
conditions, electrical overload, etc.), the 

power supply to the socket will be cut off; the 

green indicator lamp goes off

Load space cover

 

 

 

 

►  To remove it, lift it up.

►  To install it, insert the guides into their 

housings.

In the event of sudden deceleration, 
objects placed on the load space cover 

can turn into projectiles.

Loading area fittings

Stowing rings

 

 

 

 

 

 

 

 

Use the stowing rings on the rear floor to secure 

loads.
As a safety precaution in case of sharp braking, 
we recommend placing heavy objects as far 
forwards as possible (i.e. near the cab).

We recommend immobilising the load by firmly 

securing it using the stowing rings present on 

the floor.

14/02/2022   15:33:17

71

Ease of use and comfort

3

Load retaining partition

 

 

 

 

On the floor, behind the front seats, a vertical 

partition protects the driver and front passengers 
against the risk of load movement.
Steel or glazed partitions separate the loading 
area from the cab.

Recommendations on 

loading

The weight of the load must comply with 
the Gross Train Weight (GTW).

For more information on 

Engine technical 

data and towed loads

, refer to the 

corresponding section.

If you are using a carrying system (roof 
bars/roof rack), comply with the 

maximum loads associated with this system.
For more information on 

Roof bars/Roof 

rack

, refer to the corresponding section.

Make sure that the size, shape and 
volume of the loads carried are 

compatible with the highway code and safety 

regulations and do not impair the driver’s field 

of vision.

The load must be evenly distributed in 
the loading area so as not to interfere 

with driving the vehicle.
Place the load close to the side wall panels, 
or push it against the side wall panels 
between the wheel arches.
However, it is recommended that heavy 
objects are placed as close to the cab as 
possible as a precaution in case of sharp 
braking.

Firmly secure all parts of the load using 

the stowing rings on the floor of the 

loading area.
For more information on the 

Interior fittings

 

and in particular on the stowing rings, refer to 
the corresponding section.

To avoid the risk of injury or accident, the 
load must be made stable so that it 

cannot slide, tip over, fall or be projected. To 
do this, use only retaining straps that conform 
to current standards (DIN, for example).
For more information on putting straps in 
place, refer to the manufacturer’s user guide.
To prevent the load from sliding, there must 
not be any empty spaces between the load 
items and the vehicle wall panels.
As well as the straps, optimise the stability 
of the load with stable handling equipment 
(wedges, rigid blocks of wood or padding).

When washing your vehicle, never clean 
the inside directly using a water jet.

14/02/2022   15:33:17

72

Ease of use and comfort

Seating area fittings

 

 

High load retaining net

This allows the use of the entire loading capacity, 
up to the roof:
–  behind the front seats in row 1, when the rear 
seats (and bench seats) in rows 2 and 3 are 
folded or removed,
–  behind the rear seats (and bench seats) in row 
2, when the rear seats (and bench seats) in row 
3 are folded or removed.

Upper fixings

 

 

►  Unclip the anchorage cover in the roof on 

each side.

Lower fixings (behind row 1)

If your vehicle has 

fixed

 one-piece bench seats 

or seats and bench seats:

 

 

►  On each side in row 2, insert the fixings in the 

floor anchorages (as shown above).

If your vehicle has seats and bench seats or 
individual seats on 

rails

:

 

 

►  On each side in row 2, insert the fixings in the 

floor anchorages then turn them a quarter turn to 

lock them in place (as shown above).
Place them as close as possible to the end of 
the rail.

Lower fixings (behind row 2)

 

 

►  Use the stowing rings.

Fit the net

Unclip the upper fixing covers and secure the 

lower fixings (as previously described).

►  Fold (table position) the seats and bench 

seats in rows 2 and 3 (according to equipment).

►  Close the rear heating and air conditioning 

vents (depending on the equipment you have).

►  Unroll the high load retaining net.

►  Position the net upper fixings in the 

corresponding anchorages in the roof (first one 

side, then the other).

►  Fully extend the straps.

►  On each side, attach the bottom fixings of the 

net to the lower anchorages (behind row 1) or in 
the stowing rings (behind row 2).

►  Tension the straps to extend the net.

►  Check that the net is attached securely and 

properly extended.

14/02/2022   15:33:17

73

Ease of use and comfort

3

Never use the ISOFIX ring provided for 

fixing the strap of a child seat with Top 

Tether.

Rear windows in row 2

If fitted to your vehicle, the side windows in row 2 

can be opened.

 

 

While driving, the windows must be closed or 
secured at one of the notches.

►  Squeeze the two controls then move the 

window sideways.

For more information on the 

Child lock 

on rear windows

, refer to the 

corresponding section.

Side blinds

Fitted to the windows in row 2, these protect the 
passenger compartment from the sun's rays.

 

 

►  Pull the tab 

A

 and attach the blind to the hook 

B

.

Always guide the blind slowly, using the 

tab, when raising or lowering it.

Panoramic sunroof

 

 

This is fitted with two manual and independent 

blinds, which improve thermal and acoustic 
comfort.

Blinds
Opening/Closing

 

 

►  Take one of the blinds by its grip and push it 

back or pull it forwards to the desired position.

Retractable sliding table

Shine

, 

Business Lounge

 

14/02/2022   15:33:17

74

Ease of use and comfort

 

The table has a central storage space covered 
by a lid. When deployed, this device becomes 
a table with two table tops on which you can 
place objects. The central part has two cup/
can holders and can also be used to hold small 
objects (e.g. credit card, pen).
The assembly is mounted on a runner allowing it 
to be positioned either in row 2 or row 3. 

Storage

 

 

►  Slide back the cover for access to 11 litres of 

storage space.

The storage space can only support a 
maximum weight of 3 kg; do not exceed 

this maximum load in use.

Moving forward or backward

 

 

►  Lift the control (without going beyond the 

point of resistance) and slide the assembly 
forwards or backwards.

►  Release the control when it is in the desired 

position.

►  Check that the table is secured on the runner. 

If this is not the case, move the assembly slightly 
to the next notch on the runner.

You can move the table in both the open 
and stowed position. However, to ensure 

safety, it is advised that you handle the 
assembly in the stowed position.

For the table to run smoothly, ensure that 
no objects are blocking the space used 

by the runner on the floor.

Before manoeuvring the table, check that 
there is nothing on the table.

Unfolding

 

 

►  Operate the control on the top and pull the 

table assembly up until it clicks into place.

►  Pull each table top fully up then pivot them on 

each side into the horizontal position.

Folding

►  Raise each table top, going beyond the point 

of resistance, to the vertical position.

►  Push each table top down into its housing 

until it clicks into place. 

 

14/02/2022   15:33:18

75

Ease of use and comfort

3

 

►  Push the control then tip the table assembly 

downward until it clicks into place.

Before stowing the table tops, check that 
they are clear. Before tipping the 

assembly down, check that the two table tops 
have clicked home in the low position and that 
there is nothing in the cup holder area (such 
as a can or pen).

Cup holders

Two cups or cans and small objects (such as 
a credit card, portable ashtray or pen) can be 
carried in the middle of the unfolded table.

Liquids carried in an open vessel (a cup 
or mug) could be spilt, presenting a risk. 

Be careful.
Never use the table in this position while the 
vehicle is being driven.

Removal

 

 

►  Raise the control fully to release the 

anchorages and tip the table assembly forward. 

►  Remove the table assembly through the 

sliding door in row 2.

Check that there is nothing in the space 

around the runner on the floor, so that 

the table disengages cleanly.

Changing the direction

 

 

With the table removed, you can turn it 180°.

Remove a seat to make this easier. 

Refitting

►  Check that there is no object obstructing the 

runner and preventing proper locking.

 

 

14/02/2022   15:33:18

76

Ease of use and comfort

►  Check that the control is in the upper position 

(locking mechanism armed). If not, lift this control 
fully to arm the mechanism.

►  Place the front of the table on the runner.

►  Taking care not to interfere with the control, 

tip the assembly towards the rear until you hear 
it lock into place.

►  Check that the assembly is fully locked into 

the runner. If not, slide the assembly gently along 
the runner until it meets the next notch.

Check that the table is fully locked into 
the runner - risk of injury in the event of 

an accident or sudden braking.

►  Release the control until the guide locks into 

the runner.

Be careful of passengers' feet when 
manoeuvring the assembly.

Storage off the runner

If removing the table from the vehicle for 
storage, ensure that it is placed in a 

clean area, in order to avoid introducing any 
foreign bodies into the mechanisms.
The table must be placed outside the vehicle, 

on a flat and level surface, resting on the 

guide so as not to damage visible parts.

Caution, when out of the vehicle, the 
table leans to the right or left when 

placed on a surface.

 

 

Incorrect use of the table can cause 
serious injury.

Never use the table in the open or deployed 
position while the vehicle is in motion. In the 
event of sudden braking, any object placed on 
the table can become a projectile.
Ensure that the table is correctly stowed in 

the low position before setting off.

Never use the table tops as seats or lean on 
them.
A label attached to the side of the table 
serves as a reminder of this.

Never place hot objects such as 
saucepans or frying pans on the table 

- risk of damaging the surface and starting a 

fire!

When the table is deployed, each table 
top can support a maximum of 10 kg. If 

you exceed the maximum weight limit, you 
risk damaging part or all of the table.
Never lift the table when it is between 
individual seats; you risk damaging the table 
tops.

 

 

Before moving the table or an individual 
seat forwards or backwards, make sure 

that the seat's backrest is upright and the 
table is stowed.

 

14/02/2022   15:33:18

77

Ease of use and comfort

3

 

When stowing the table tops, never place 
your hand inside the slide area - risk of 

trapping your fingers! Use the handle 

provided.

Heating and Ventilation

Advice

Using the ventilation and air 

conditioning system

►  To ensure that air is distributed evenly, 

keep the external air intake grilles at the base 
of the windscreen, the nozzles, the vents, the 
air outlets and the air extractor in the boot 
free from obstructions.

►  Do not cover the sunshine sensor located 

on the dashboard; this sensor is used to 
regulate the automatic air conditioning 
system.

►  Operate the air conditioning system for at 

least 5 to 10 minutes once or twice a month to 
keep it in good working order.

►  If the system does not produce cold air, 

switch it off and contact a Fiat Dealership or a 

qualified workshop.

When towing a large load on a steep gradient 

in high temperatures, switching off the air 

conditioning increases the available engine 
power, enhancing the towing capacity.

Avoid driving for too long with the 

ventilation off or with prolonged operation 

of interior air recirculation. Risk of misting and 
deterioration of the air quality!

If the interior temperature is very high 
after the vehicle has stood for a long 

time in the sunshine, air the passenger 
compartment for a few moments.

Put the air flow control at a setting high 

enough to quickly change the air in the 
passenger compartment.

Condensation created by the air 
conditioning results in a discharge of 

water underneath the vehicle. This is perfectly 
normal.

Servicing the ventilation and air 

conditioning system

►  Ensure that the passenger compartment 

filter is in good condition and have the filter 

elements replaced regularly.
We recommend using a composite passenger 

compartment filter. Its specific active additive 

helps protect against polluting gases and bad 
smells.

►  To ensure correct operation of the 

air conditioning system, have it checked 
according to the recommendations in the 
Manufacturer’s service schedule.

 

 

Contains R134A fluorinated 

greenhouse gases

Depending on version and country of sale, the 
air conditioning system may contain R134A 

fluorinated greenhouse gases. Gas capacity 

0.5 kg (+/- 0.025 kg), GWP index 1430 (CO

2 

equivalent: 0.715 t).

Stop & Start

The heating and air conditioning systems 

only work when the engine is running.
Temporarily deactivate the Stop & Start 
system to maintain a comfortable temperature 
in the passenger compartment.
For more information on 

Stop & Start

, refer 

to the corresponding section.

ECO driving mode

Selecting this mode reduces electrical 

energy consumption, but restricts the 
performance of the heating and air 
conditioning systems, although it does not 
deactivate them.

14/02/2022   15:33:18

78

Ease of use and comfort

Heating

 

 

Manual air conditioning

The air conditioning system only operates with 
the engine running.

 

 

1.

Temperature.

2.

Air flow.

3.

Air distribution.

4.

Interior air recirculation.

5.

Air conditioning on/off.

Air flow

►  Turn the thumbwheel 

2

 to obtain a 

comfortable air flow.

If you set the air flow control to the 

minimum

 position (off), the temperature 

in the vehicle will no longer be controlled. A 

slight air flow can still be felt however, 

resulting from the forward movement of the 
vehicle.

Temperature

►  Turn the thumbwheel 

1

 from "

LO

" (cold) 

to "

HI

" (hot) to adjust the temperature to your 

requirements.

Air distribution

►  Pressing button 

3

 successively directs the air 

flow towards:

–  windscreen, side windows and footwells, 
–  footwells,
–  central vents, side vents and footwells,
–  windscreen, side windows, central vents, side 
vents and footwells,
–  central and side vents, 
–  windscreen and side windows (demisting or 
defrosting).

Air conditioning

With the engine running, the air conditioning is 

designed to operate effectively in all seasons, 

with the windows closed.
It enables you to:
–  lower the temperature in summer,

–  enhance the effectiveness of the demisting 

function in winter, above 3°C.

On/Off

►  Press button 

5

 to activate/deactivate the air 

conditioning system.
When the air conditioning is in operation, to 
cool the air more quickly, you can use interior 

air recirculation for a few moments by pressing 
button 

4

. Then restore the intake of exterior air.

The air conditioning does not operate 

when the air flow adjustment is set to off.

Switching the system off could result in 

discomfort (humidity, misting).

Dual-zone automatic air 
conditioning

 

 

1.

Temperature.

2.

Air flow.

3.

Air distribution.

4.

Recirculation of interior air.

5.

Air conditioning on/off.

6.

Automatic comfort mode.

7.

Visibility programme.

8.

“Mono” function or Rear heating and air 

conditioning on/off (depending on version).

Automatic comfort mode

►  Press the "

AUTO

" button 

6

 to toggle the 

mode.

14/02/2022   15:33:18

79

Ease of use and comfort

3

The active mode appears in the display screen, 
as described below:

Ensures soft, quiet operation by limiting 

air flow.

Offers the best compromise between a 

comfortable temperature and quiet 

operation.

Provides dynamic, effective air flow.

 

When the engine is cold, the air flow will 

only increase to its optimum level 

gradually, to avoid distributing too much cold 
air.
In cold weather, it prioritises the distribution of 
warm air to the windscreen, the side windows 
and the footwells only.

Manual mode

It is possible to make a different choice from that 

offered by the system by changing a setting. 

The other functions will still be automatically 
managed. 
The "

AUTO

” symbol disappears if you change a 

setting.

Deactivating the system

►  Press button 

2

 "

-

" until the fan symbol 

disappears.

This action switches off all of the functions of the 

system.

Temperature is no longer controlled. A slight air 

flow can still be felt, however, resulting from the 

forward movement of the vehicle.

►  Press button 

2

 "

+

" to switch the system on 

again.

Temperature

The driver and front passenger can each set the 
temperature to suit their preferences.
The value shown on the display is a level 
of comfort, not a temperature in Celsius or 
Fahrenheit.

►  Push button 

1

 down to decrease the value or 

up to increase it. 

A setting of around 21 provides optimum 

comfort. Depending on your 

requirements, a setting between 18 and 24 is 
normal.
In addition, we recommend avoiding left/right 

setting differences of more than 3.

On entering the vehicle, if the interior 

temperature is significantly colder or 

warmer than the comfort value setting, there 
is no need to alter the value displayed in 
order to reach the required level of comfort. 
The system compensates automatically and 

corrects the temperature difference as quickly 

as possible.

For maximum cooling or heating of the 
passenger compartment, it is possible to 

exceed the minimum value 14 or the 
maximum value 28.

►  Push button 

1

 down until 

"LO"

 is 

displayed or up until 

"HI"

 is displayed.

"Mono" function

The comfort setting for the passenger's side 
can be indexed to the driver's comfort setting 
(mono-zone).

 

 

►  Press the corresponding button 

8

 to activate/

deactivate the function.
The indicator lamp in the button is on when the 
function is activated.
The function is deactivated automatically if a 
passenger uses the temperature control.

Rear heating - air 

conditioning

 

 

►  Press the corresponding button 

8

 to activate/

deactivate the function.

For more information, refer to the 

Rear 

heating - air conditioning

 section.

14/02/2022   15:33:19

80

Ease of use and comfort

Visibility programme

►  Press the "

visibility

" button 

7

 to demist or 

de-ice the windscreen and side windows more 
quickly. 
The system automatically manages the air 

conditioning, air flow and air intake, and provides 

optimum distribution towards the windscreen and 
side windows.

►  Press the "

visibility

" button 

7

 again to stop 

the programme.
Or

►  Press the "

AUTO

" button 

6

 to return to the 

automatic comfort programme.

Air 

conditioning

With the engine running, the air conditioning is 

designed to operate effectively in all seasons, 

with the windows closed.
It is used to:
–  lower the temperature in summer,

–  increase the effectiveness of the demisting in 

winter, above 3°C.

On/Off

►  Press button 

5

 to activate/deactivate the air 

conditioning system.
When the air conditioning is in operation, to 
cool the air more quickly, you can use interior 
air recirculation for a few moments by pressing 
button 

4

. Then restore the intake of exterior air.

The air conditioning does not operate 

when the air flow adjustment is set to off.

Switching the system off could result in 

discomfort (humidity, misting).

Air distribution

►  Pressing button 

3

 successively directs the air 

flow towards:

–  windscreen, side windows and footwells, 
–  footwells,
–  central vents, side vents and footwells,
–  windscreen, side windows, central vents, side 
vents and footwells,
–  central and side vents, 
–  windscreen and side windows (demisting or 
defrosting).

Air flow

►  Press the buttons 

2

 to increase/decrease the 

air flow.

The air flow symbol (a fan) appears. It is filled in 

or emptied gradually, according to the value set.

Interior air recirculation

The intake of exterior air prevents the formation 
of mist on the windscreen and side windows.
Recirculating the interior air isolates the 
passenger compartment from outside odours 
and fumes and allows the desired passenger 
compartment temperature to be achieved more 
rapidly.

►  Press this button to activate/deactivate 

the function (confirmed by the 

illumination/extinction of the indicator lamp).

Front demisting 
- defrosting

These markings on the control panel 
indicate the positioning of the controls for 

rapid demisting or defrosting of the windscreen 
and side windows.

Heating or manual air 

conditioning

 

 

 

 

►  Set the air flow, temperature and air 

distribution controls to the appropriately marked 
positions.

14/02/2022   15:33:19

81

Ease of use and comfort

3

►  For air conditioning, press this button; 

its indicator lamp comes on.

Dual-zone automatic air 

conditioning

 

 

►  Press this button to demist or defrost 

the windscreen and side windows more 

quickly.
The system automatically manages the air 

conditioning, air flow and air intake, and provides 

optimum distribution towards the windscreen and 
side windows.

►  To turn it off, press this button 

again or press "

AUTO"

.

The system restarts with the values in use before 
it was deactivated.

Demisting/de-icing the 
rear screen and/or the 
door mirrors

 

 

 

 

►  Press one of these buttons to switch on/off 

rear screen and door mirror demisting/de-icing 
(depending on version).
The indicator lamp in the button comes 

on

 when 

the function is 

activated

.

Demisting/de-icing switches off automatically to 

prevent excessive power consumption.

Switch off demisting/de-icing as soon 

as you no longer consider it necessary, 

as decreased power consumption in turn 
reduces energy consumption.

Demisting/de-icing only operates with the 
engine running.

Rear heating - air 
conditioning

 

 

 

 

If your vehicle is fitted with a rear air conditioning 

unit located in the roof, this system distributes 
conditioned and heated air via a distribution rail 
and individual outlets.

14/02/2022   15:33:19

82

Ease of use and comfort

Air flow

►  Turn the dial to increase or decrease 

the air flow.

Comfort temperature

–  Turn the thumbwheel from blue (cold) 
to red (hot) to modulate the temperature 

to your liking.
This control simultaneously adjusts the 
temperature and the location of the air delivery:
–  blue: the air is delivered mainly at roof level,
–  red: the air is delivered mainly by the vent 
located in row 3 on the right.

Activation/Deactivation

 

 

Depending on version, this button is accessible 
at the front, from the dual-zone automatic air 
conditioning control panel.

►  Press this button to activate/deactivate 

the operation of the rear controls.

Additional heating/

ventilation system

Only available for Diesel vehicles.

 

 

 

 

Heating

This is an additional and separate system which 
heats the passenger compartment and improves 
defrosting performance.

This indicator lamp is lit while the system 
is programmed or set in operation 

remotely via the remote control.

It flashes during the whole duration of the 

heating and goes off at the end of the heating 

cycle or when stopped using the remote control.

Ventilation

This system allows ventilation of the passenger 
compartment with exterior air to improve the 
temperature experienced on entering the vehicle 
in summer.

Programming

With a Connect Nav, use the remote control to 
start/stop the additional heating.
With a Bluetooth

®

 audio system or a Connect 

Radio, use the remote control to start/stop the 
additional heating and/or adjust the pre-heating 
times.

With Bluetooth

®

 audio system

 

 

►  Press the 

MENU

 button to access the 

main menu. 

►  Select "

Pre-heat. / Pre-ventil.

".

►  Select "

Activation

" and, if necessary, for 

programming, 

“Parameters

".

►  Select "

Heating

" to heat the engine and 

passenger compartment or "

Ventilation

" to 

ventilate the passenger compartment.

 

 

►  Select:

•  the first clock to set/save the time at which 

the pre-heating temperature will be reached,

•  the second clock to set/save a second time 

at which the pre-heating temperature will be 
reached,

14/02/2022   15:33:20

83

Ease of use and comfort

3

Using these two clocks and depending 
on the season you can, for example, 

select one or the other start time.

A message on the screen confirms your 

choice.

With Connect Radio

Press 

Connect-App

 to display the main 

page.
Then press "

Programmable heating/

ventilation

".

►  Select the "

Status

" tab to activate/deactivate 

the system.

►  Select the "

Other settings

" tab to choose 

the "

Heating

" mode, to heat the engine and 

passenger compartment, or "

Ventilation

" to 

ventilate the passenger compartment.

►  Then set/save the time at which the 

preheating temperature will be reached for each 
selection.

Press this button to save. 

With Connect Nav

In the 

Applications > Car Apps

 menu: 

►  Select 

Temperature conditioning

. 

►  Press the 

Status

 tab to activate/deactivate 

the system.

►  Press the 

Settings

 tab to select 

Heating

 

mode to heat the engine and passenger 

compartment or 

Ventilation

 to ventilate the 

passenger compartment.

►  Then programme/save the activation time for 

each selection.

►  Press 

OK

 to confirm.

You must allow at least 60 minutes 
between programming operations.

Depending on the outside temperature, a 
certain amount of pre-conditioning time is 

necessary in order to reach the programmed 
temperature by the stored activation time.
This pre-conditioning time lasts up to 45 min.

Long-range remote control

This enables you to switch the heating in 

the passenger compartment on or off from a 

distance.
The remote control has a range of about 0.6 
miles (1 km) in open country.

 

 

On

►  Pressing and holding this button starts 

the heating immediately (confirmed by the 

green indicator lamp coming on briefly).

Switching off

►  Pressing and holding this button stops 

the heating immediately (confirmed by the 

temporary illumination of the red indicator lamp).

The indicator lamp in the remote control flashes 

for about 2 seconds if the vehicle has not 
received the signal.
Then repeat the command after having changed 
location.

Changing the battery

The indicator lamp in the remote control will 
change to orange if the battery charge is low.
If the indicator lamp is not on, the battery is 
discharged.

 

 

14/02/2022   15:33:21