Fiat Ulysse (2022 year). Manual in english - page 3

36

Access

Central locking

 

 

 

 

Manual

►  Press this button to lock/unlock the vehicle 

(doors, tailgate or side-hinged doors) from inside 
the passenger compartment. 

The indicator lamp comes on to confirm the 

central locking of the vehicle.

Central locking does not take place if any 
of the doors are open.

When locking/deadlocking from the 

outside

When the vehicle is locked or deadlocked 

from the outside, the indicator lamp flashes 

and the button is deactivated.

►  After normal locking, pull one of the 

interior door controls to unlock the vehicle.

►  After deadlocking, you must use the 

remote control, the "Keyless Entry and 
Start" system or the built-in key to unlock the 
vehicle.

Driving with the doors locked makes 
access for the emergency services more 

difficult in an emergency.

 

 

When transporting an oversized load 
(tailgate or side-hinged doors open), 

press the button to lock only the cab doors.

 

 

When transporting an oversized load 
(tailgate or side-hinged doors open), 

press the button to lock only the front and rear 
doors (sliding side door).

When locking from inside, the door 
mirrors do not fold.

Central locking from the inside does not 
operate if one of the doors is open (indicated 
by a mechanical noise coming from the 
locks).
When the tailgate or side-hinged doors are 
open, only the other doors are locked (the 
button does not light up).

Automatic (anti-intrusion 

security)

The doors and the tailgate or the side-hinged 
doors can lock automatically while driving (speed 
above 6 mph (10 km/h)).
To deactivate/reactivate this function (activated 
by default):

►  Press the button until an audible signal is 

heard and/or a message appears on the screen.

Locking/unlocking the 

loading area

 

 

 

 

 

 

This button is unavailable if the vehicle 
has been locked or deadlocked from 

outside (using the key, remote control or 
Keyless Entry and Start, depending on 
equipment) or if any of the doors are still 
open.

14/02/2022   15:33:08

37

Access

2

Automatic

The 

loading area

 is always locked when driving.

To deactivate this automatic locking, go 

to a Fiat Dealership or a qualified 

workshop.

Manual

►  With complete unlocking activated, 

press this button to lock (indicator lamp 

comes on)/unlock (indicator lamp goes off) the 

vehicle

.

►  With selective unlocking activated, press this 

button to lock (indicator lamp comes on)/unlock 

(indicator lamp goes off) the 

loading area

.

Driving with the doors locked could make 

it more difficult for the emergency 

services to enter the vehicle in an emergency.

The indicator lamp goes off when 

unlocking one or more doors of the 

loading area

.

With the ignition off and the vehicle fully 

locked, the indicator lamp goes off for energy 

economy reasons.

Electric sliding side 
door(s)

The exterior and interior door handles and the 
interior buttons allow the electrically powered 
movement of the door to be started.
Opening and closing of the doors is 
accompanied by an audible signal.

Opening

With the exterior or interior handle

 

 

►  With the door unlocked, pull and release the 

handle to start opening the door. Pull the handle 
again to reverse the direction of the door's 
movement.

With the remote control

 

 

►  With the door unlocked, press and 

hold this button until the corresponding 

sliding side door has opened. 

►  Press this button again to reverse the 

direction of the door's movement.

The remote control buttons are not active 
with the ignition switched on.

With the button(s) on the door pillar

 

 

 

 

With the button(s) at the front

 

 

 

 

►  With total unlocking activated and the child 

lock deactivated, to unlock the vehicle and start 

14/02/2022   15:33:09

38

Access

opening a door, press the button corresponding 
to the door you wish to open.

►  With selective unlocking activated, to unlock 

only the 

loading area

 and start opening a door, 

press the button corresponding to the door you 
wish to open.

►  In both cases, pressing the button again 

reverses the direction of the door's movement.

Closing

With the exterior handle

 

 

►  Pull and release the handle to start closing 

the door. Pull the handle again to reverse the 
direction of the door's movement.

With the remote control

►  Press and hold this button until the 

sliding side door has closed. Pull the 

handle again to reverse the direction of the 
door's movement.

The remote control buttons are not active 
with the ignition switched on.

With the button(s) on the door pillar

 

 

 

 

With the button(s) at the front

 

 

 

 

►  To start closing a door, press the 

corresponding button for that door. Press again 
to reverse the direction of the door's movement.

The button is not operational and 
pressing it results in an audible signal, if 

the speed of the vehicle is above 20 mph (30 
km/h).

The button(s) at the front or on the door 
pillar is not operational and pressing it 

results in an audible signal, if:
–  the vehicle is moving,
–  the child lock is on (activated) (for the 
buttons on the door pillars),
–  the vehicle has been locked or deadlocked 
from outside (using the key, remote control 
or Keyless Entry and Starting, depending on 
equipment).
The button for the left-hand door is not 
operational and pressing it results in an 

audible signal if the fuel filler flap is open.

General 
recommendations for the 
sliding side doors

Doors must only be operated when the 
vehicle is stationary.

For your safety and that of your passengers, 
as well as for correct operation of the doors, 
you are strongly advised not to drive with a 
door open.
Always check that it is safe to operate the 
door and in particular, be sure not to leave 
children or animals near the door controls 
without supervision.
The audible warning, the lighting of the "door 
open" warning lamp and the message on the 
screen are there to remind you. Contact a Fiat 

14/02/2022   15:33:09

39

Access

2

Dealership or a qualified workshop if you want 

to deactivate this warning.
Lock the vehicle when you use an automatic 
car wash.

Before opening or closing and while 
moving doors, ensure that no person, 

animal or object is in the door frame or any 
other position that would block the desired 
movement, inside or outside the vehicle.
If this advice is not followed, injuries or 
damage may occur if any part of a person or 
an object is trapped or caught.
Electrical door opening is disabled at speeds 
above 2 mph (3 km/h):
–  However, if the vehicle started moving 
while the doors were open, the speed must 

be reduced below 19 mph (30 km/h) before 

they can be closed.
–  Any attempt to open a door electrically 
using the interior handle while driving results 
in it only being possible to open the door 
manually.
–  This situation is accompanied by the 
audible warning, the lighting of the "door 
open" warning lamp and the message on the 
screen. To release the door and be able to 
operate it again, it is necessary to stop the 
vehicle.

Take care not to block the guide space 

on the floor so that the door can slide 

correctly.
For safety and functional reasons, do not 
drive with the sliding side door open.

The electric controls are disabled in the 
event of an impact. Manual opening and 

closing remain possible.

While starting the engine, door 
movements are paused, resuming when 

the engine is running.

Depending on the engine fitted, if 

the door is closed and an opening 

request is issued in Stop mode of Stop & 
Start, the door will open slightly and then 
stop. In Start mode, the door will resume its 
movement when the engine re-starts.

To hold the sliding side door in the open 
position, open the door fully to engage 

the latch (located at the bottom of the door).

Doors and door clearances

 

 

When open, a door projects beyond the body. 
Allow adequate clearance when parking 
alongside walls, lamp-posts, high pavements, 
etc.

 

 

When open, a door never projects 
beyond the rear bumper.

14/02/2022   15:33:09

40

Access

Safety/Obstacle detection 

with electric door(s)

 

 

The obstacle detection system is triggered when 
the moving door encounters an obstacle with a 
certain level of physical resistance. If an obstacle 
is detected:
–  while the door is closing, the door stops then 
opens fully.
–  while the door is opening, the door stops then 
closes.
–  twice in succession during a movement of the 
door, the door will no longer close electrically 
(uninitialisation).
On a steep slope: a safety system slows down 
the movement of the door.
In all cases, wait a few seconds before operating 
the door (closing or opening).
Close the door manually for safety reasons.
Then reinitialise the door.

Reinitialising electric doors

If electrical operations no longer work:

►  Fully close the door(s) 

manually

.

►  Fully open the door(s) 

electrically

.

►  Close the door(s) 

electrically

.

On completion of this procedure, electric 
operation of the doors is restored.
However, if a problem persists following this 
procedure, contact a Fiat Dealership or a 

qualified workshop.

On a steep slope

 

 

It is possible to open and close the doors 
electrically on slopes of up to a 20% gradient.
If the vehicle is on a slope, with the front of the 
vehicle facing up the slope, open the door with 
care. The door may open more quickly due to 
the incline.
On a steep slope, guide the side door manually 
to help it to close.

 

 

If your vehicle is on a slope, with the front of the 
vehicle facing down the slope, the door may not 
stay open and may close 

violently

 with the risk 

of injury.

In the case of a steep slope, the door 
may be driven by its own weight and as a 

consequence may open or close 

violently

.

There would not be time for action at the 

electric controls to take effect.

There would not be time for the obstacle 

detection system to react.

Take care not to leave the vehicle on a 
steep slope with the door(s) open without 
supervision. If this advice is not followed, 
injuries or damage may occur if a person or 
an object is trapped or caught.

14/02/2022   15:33:09

41

Access

2

Hands-free sliding side 
door(s)

Opening/Closing

 

 

With a movement of your foot while keeping the 
remote control on your person in the recognition 
zone 

A

, the system unlocks and opens the 

sliding side door or closes and locks it.
The remote control must be located at the rear 
of the vehicle, at least about 30 cm but no more 
than about 2 m from the vehicle.

The automatic locking after closing the 
door can be programmed in the vehicle 

configuration menu.

Before making the movement with your 
foot, ensure that you are steady and well 

positioned, so that you do not lose your 
balance (rain, snow, ice, mud, etc.).
Take care not to touch the exhaust tailpipe 
when making the movement with your foot - 
risk of burns.

 

 

►  Put your foot beneath the corner of the rear 

bumper, then move the foot at normal speed with 
a sweeping side movement.
The sensor detects the foot approaching and 
leaving and triggers the opening or closing of the 
side door.

Make the movement without interruption 
and do not repeat it immediately 

afterwards or several times.
If the door does not open, wait about 
2 seconds before trying again.
Do not keep the foot in the air.

Confirmation that the door is going to 

open or close is signalled by the direction 

indicators flashing for a few seconds, 

accompanied by an audible signal.
The movement of the door is reversed if the 
movement of the foot takes place during the 
manoeuvre.
If the vehicle is so equipped, the electric door 
mirrors fold/unfold on locking/unlocking the 
vehicle.

Automatic locking

The vehicle locks itself following the hands-free 
closing of the sliding door.

If your vehicle is not fitted with an alarm, 

locking is signalled by the fixed 

illumination of the direction indicators for 
about two seconds.
Depending on your version, the door mirrors 
fold at the same time.

Activation/Deactivation

With audio system or touch screen

By default, hands-free access is activated.

The "Hands-Free Tailgate Access" 
function or automatic vehicle 

locking when the sliding door is closed is 
activated and deactivated via the vehicle 

configuration menu.

14/02/2022   15:33:09

42

Access

Malfunction

An audible signal repeated three times while 
using the function indicates a fault with the 
system.
Have it checked by a Fiat Dealership or a 

qualified workshop.

If the "

Hands-free tailgate access 

self-locking

" option is selected in the 

vehicle menu and after closing the door, 
check that the vehicle is properly locked.
Locking will not take place:
–  if the ignition is on,
–  if one of the doors or the tailgate is open,
–  if a "Keyless Entry and Start" remote 
control is inside the vehicle. 
If a number of gestures with your foot have 

no effect, wait a few seconds before starting 

again.
The system is automatically deactivated in 
heavy rain or with accumulations of snow.
If it does not work, make sure that the 
remote control is not exposed to a source of 
electromagnetic interference (smartphone, 
etc.).

Operation may be affected if using a 

prosthetic leg.
This system may not work correctly if your 

vehicle is fitted with a towbar.

The side door may open or close without 
warning if: 

–  Your vehicle is fitted with a towbar.

–  A trailer is coupled or decoupled.
–  A bicycle carrier is installed or removed.
–  Bicycles are loaded on to or unloaded from 
the bicycle carrier.
–  Something is deposited or lifted behind the 
vehicle.
–  An animal approaches the bumper,
–  The vehicle is washed.
–  The vehicle is being serviced.
–  A wheel is changed. 
To avoid any sudden operation, keep the key 
away from the detection zone (also from the 
boot’s interior sides) or deactivate the function 

in the vehicle configuration menu.

Ensure that no person or object might 
prevent the correct opening or closing of 

the doors.
Be aware of children when operating the 
doors.

Side-hinged rear doors

 

 

►  After first opening the left-hand door, pull the 

lever 

A

 towards you to open the right-hand door.

Closing

►  First close the right-hand door, then the left-

hand door.

If the left-hand door is closed first, a 

buffer stop located on the edge of the 

right-hand door prevents it closing.

If the left-hand side-hinged door is not properly 
closed, the "

door open

" warning lamp lights up 

14/02/2022   15:33:10

43

Access

2

(the right-hand door is not detected). For more 
information on the 

List of warning lamps

 and, 

in particular, the door open warning, refer to the 
corresponding section.

Opening to approximately 

180°

 

 

If fitted to your vehicle, a check strap system 

allows the doors to be opened from about 90° to 

about 180°.

►  Pull the yellow control when the door is open.

The check strap will engage again automatically 
on closing.

When parked with the rear doors open to 

90°, the doors will cover the rear lamps. 

In order to warn other road users travelling in 
the same direction (who may not be aware 
that the vehicle is stationary) of the vehicle's 
position, use a warning triangle or other 

device required by legislation and regulations 
in your country.

Tailgate

Opening

 

 

►  After unlocking the vehicle, pull the handle, 

then raise the tailgate.

Closing

►  Lower the tailgate using the interior grab 

handle, then lock it.
If the tailgate is not properly closed, the "

door 

open

" warning lamp comes on. For more 

information on the 

list of warning and indicator 

lamps

, and in particular the door open warning, 

refer to the corresponding section.

In the event of a malfunction or if you 

experience difficulty opening or closing 

the tailgate, have it checked by a Fiat 

Dealership or a qualified workshop without 

delay, to avoid the issue deteriorating and 
prevent any risk of the tailgate dropping, 
potentially causing serious injury.

Tailgate rear screen

The opening rear screen allows you to access 
the rear of the vehicle directly, without having to 
open the tailgate.

Opening

 

 

After unlocking the vehicle, press this control and 
lift the rear screen to open it.

Closing

Close the rear screen by pressing the centre of 
the glass until it is fully closed.
If the tailgate rear screen is not properly closed, 
the "

door open

" warning lamp comes on. For 

more information on the 

list of warning and 

14/02/2022   15:33:10

44

Access

indicator lamps

 and in particular the door open 

warning, refer to the corresponding section.

The tailgate and rear screen cannot both 
be open at the same time, to avoid 

damaging them.

Alarm

 

 

(Depending on version)

 

 

 

 

System which protects and provides a deterrent 
against theft and break-ins.

Exterior perimeter monitoring

The system checks for opening of the vehicle.
The alarm is triggered if anyone tries to open a 
door, the boot or the bonnet, for example.

Interior volumetric monitoring

The system only checks for any 
variation in volume in the 

cab

.

The alarm is triggered if anyone 
breaks a window or enters the 
vehicle’s 

cab

; however it is not 

triggered if someone enters the 

loading area

.

The system checks for any 
variation in volume in the 
passenger compartment.
The alarm is triggered if anyone 
breaks a window, enters the 
passenger compartment or 
moves inside the vehicle.

Self-protection function

The system checks whether any of its 
components are out of service.
The alarm is triggered if the battery, the central 
control or the siren wiring is put out of service or 
damaged.

Work on the alarm system

Contact a Fiat Dealership or a qualified 

workshop.

If your vehicle is fitted with Additional 

Heating / Ventilation, volumetric 

monitoring is not compatible with this system.
For more information on 

Additional Heating 

/ Ventilation

, refer to the corresponding 

section.

Locking the vehicle with full 

alarm system

Activation

►  Switch off the ignition and exit the vehicle.

►  Lock or deadlock the vehicle using the 

remote control or with the Keyless Entry and 
Start system.
When the monitoring system is active, the red 

indicator lamp in the button flashes once per 

second and the direction indicators come on for 
about 2 seconds.
The exterior perimeter monitoring is activated 
after 5 seconds and the interior volumetric 
monitoring after 45 seconds.

If an opening (door, tailgate/side-hinged 
doors or bonnet) is not properly closed, 

the vehicle is not locked, but the exterior 
perimeter monitoring will be activated after 45 
seconds, at the same time as the interior 
volumetric monitoring.

14/02/2022   15:33:10

45

Access

2

Deactivation

►  Press the remote control unlocking 

button.

or

►  Unlock the vehicle with the Keyless Entry and 

Start system.
The monitoring system is deactivated: the 

indicator lamp in the button goes off and the 

direction indicators flash for about 2 seconds.

If the vehicle automatically locks itself 
again (as happens if a door or the boot is 

not opened within 30 seconds of unlocking), 
the monitoring system is automatically 
reactivated.

Triggering of the alarm

This is indicated by sounding of the siren 

and flashing of the direction indicators for 30 

seconds.
The monitoring functions remain active until 
the alarm has been triggered ten times in 
succession.

When the vehicle is unlocked, rapid flashing of 

the indicator lamp in the button indicates that the 
alarm was triggered during your absence. When 

the ignition is switched on, this flashing stops 

immediately.

Locking the vehicle 

with exterior perimeter 

monitoring only

Deactivate the interior volumetric monitoring to 
avoid the unwanted triggering of the alarm, in 
certain cases such as:
–  Slightly open window.
–  Washing the vehicle.
–  Changing a wheel.
–  Towing the vehicle.
–  Transport on a ship or ferry.

Deactivating interior volumetric 

monitoring

►  Switch off the ignition and within 10 seconds 

press the alarm button until the indicator lamp is 

on fixed.

►  Exit the vehicle.

►  Immediately lock the vehicle using the remote 

control or the "Keyless Entry and Start" system.
Only exterior perimeter monitoring is activated; 

the red indicator lamp in the button flashes every 

second.

To take effect, this deactivation must be 

performed whenever the ignition is switched 

off.

Reactivating interior volumetric 

monitoring

►  Deactivate exterior perimeter monitoring by 

unlocking the vehicle using the remote control or 
the "Keyless Entry and Start" system.

The indicator lamp in the button goes off.

►  Reactivate the full alarm system by locking 

the vehicle using the remote control or the 
"Keyless Entry and Start" system.
The red indicator lamp in the button once again 

flashes every second.

Locking the vehicle without 

activating the alarm

►  Lock or deadlock the vehicle using the key 

(integral to the remote control) in the driver's 
door lock.

Failure of the remote control

To deactivate the monitoring functions:

►  unlock the vehicle using the key (integral to 

the remote control) in the driver's door lock,

►  Open the door; this sets off the alarm.

►  Upon switching on the ignition the alarm 

stops. The button indicator lamp goes off.

Malfunction

When the ignition is switched on, the fixed 

lighting of the red indicator lamp in the button 
indicates a system malfunction.
Have it checked by a Fiat Dealership or a 

qualified workshop.

14/02/2022   15:33:10

46

Access

Automatic activation

(Depending on version)
The system is activated automatically 2 minutes 
after the last door or the boot is closed.

►  To avoid triggering the alarm on entering the 

vehicle, first press the unlocking button on the 

remote control or unlock the vehicle using the 
"Keyless Entry and Start" system.

Electric windows

1.

Left-hand front.

2.

Right-hand front.

Operation

►  To open/close the window manually, press/

pull the switch without passing the point of 
resistance; the window stops as soon as the 
switch is released.

►  To open/close the window automatically, 

press/pull the switch fully, beyond the point of 
resistance; the window opens/closes completely 
when the switch is released (pressing the switch 
again stops the movement of the window).

The electric window controls remain 
operational for about 45 seconds after 

the ignition is switched off if the front doors 

are not open.
After that time, the controls are disabled. To 
reactivate them, switch the ignition on again.

Safety anti-pinch

If your vehicle is fitted with the safety anti-pinch 

function, when the window rises and meets an 
obstacle, it stops and partially lowers.
In the event of unwanted opening of the window 
on closing, press the control until the window 
opens completely. Within 4 seconds, pull the 
control until the window closes.
The safety anti-pinch does not operate while 
doing this.

Reinitialising the electric 

windows

After reconnecting the battery, or in the event 
of abnormal window movement, the anti-pinch 
function must be reinitialised.

The anti-pinch function is disabled during the 

following sequence of operations.

For each window:

►  Lower the window fully, then raise it; it will 

rise in steps of a few centimetres each time the 
control is pressed. Repeat the operation until the 
window is fully closed.

►  Continue to pull the control for at least one 

second after the window reaches the closed 
position.

If an electric window meets an obstacle 
during operation, the movement of the 

window must be reversed. To do this, press 
the relevant control.
When the driver operates the passenger 
electric window control, it is important to 
ensure that nothing can prevent the window 
from closing properly.
Pay particular attention to children when 
operating the windows.
Do not put your head or arms through the 
open windows when the vehicle is moving - 
risk of serious injury!

14/02/2022   15:33:10

47

Ease of use and comfort

3

Correct driving position

Before taking to the road and to make the most 
of the ergonomic layout of the instruments and 
controls, carry out these adjustments in the 
following order:
–  the height of the head restraint,
–  the seat backrest angle,
–  the seat cushion height,
–  the longitudinal position of the seat,
–  the height and reach of the steering wheel,
–  the rear view mirror and door mirrors.

 

 

Once these adjustments have been 
made, check the instrument panel can be 

viewed correctly from your driving position.

Manually-adjusted front 
seats

For more information on the 

Seat belts

, 

refer to the corresponding section.

Longitudinal

 

 

►  Raise the control bar and slide the seat 

forwards or backwards.

►  Release the control bar to lock the seat in 

position on one of the notches.

Before moving the seat backwards, 
ensure that there is nothing that might 

prevent the full travel of the seat.
There is a risk of trapping or pinching 
passengers if present in the rear seats or 
jamming the seat if large objects are placed 

on the floor behind the seat.

Height

 

 

►  Pull the control upwards to raise or push it 

downwards to lower, until you obtain the position 
required.

Backrest angle

 

 

►  Depending on equipment, turn the knob 

or pull the control all the way up and tilt the 
backrest forwards or backwards to obtain the 
desired angle.

Lumbar

 

 

14/02/2022   15:33:11

48

Ease of use and comfort

►  Turn the knob to obtain the desired level of 

lumbar support.

Table position of the driver's 

and/or the front passenger 

seat backrest

 

 

On the front passenger side, this position allows 
long objects to be carried.
On the driver's side, this position allows rear 
passengers to be helped out of the vehicle (by 
the emergency services).

Check that there is no object that could 
interfere with the movement of a seat, 

both above and below.

►  Place the head restraint in the low position, 

and if fitted to your vehicle, raise the armrest and 

fold the table fitted to the back of the seat.

We recommend deactivating the front 
passenger airbag.

 

 

►  Pull the control fully up and tip the backrest 

forward.
To return to the normal position, pull the control 
up to release the backrest, then pull the backrest 
up to its raised position.

When sharp deceleration occurs, objects 
placed on the folded backrest can turn 

into projectiles.

Electric front seat

To avoid discharging the battery, carry 
out these adjustments with the engine 

running.

For more information on the 

Seat belts

, 

refer to the corresponding section.

Longitudinal

 

 

►  Push the control forwards or rearwards to 

slide the seat.

Before moving the seat backwards, 
ensure that there is nothing that might 

prevent the full travel of the seat.
There is a risk of trapping or pinching 
passengers if present in the rear seats or 
jamming the seat if large objects are placed 

on the floor behind the seat.

Seat cushion height

 

 

►  Tilt the control upwards or downwards to 

obtain the desired height.

14/02/2022   15:33:11

49

Ease of use and comfort

3

Backrest angle

 

 

►  Tilt the control forwards or rearwards to 

adjust the angle of the backrest.

Head restraint height 
adjustment

 

 

If fitted to your vehicle.

►  To raise it, pull it upwards as far as possible 

(notch).

►  To remove it, press the lug 

A

 and pull it 

upwards.

►  To put it back in place, engage the head 

restraint rods in the openings keeping them in 
line with the seat backrest.

►  To lower it, press the lug 

A

 and push down on 

the head restraint at the same time.

The head restraint has a frame with 
notches which prevents it from lowering; 

this is a safety device in case of impact.

The adjustment is correct when the upper 

edge of the head restraint is level with the 

top of the head.

Never drive with the head restraints removed; 

they must be fitted and correctly adjusted.

2-seat front bench seat

If fitted in the vehicle, this is fixed and has a seat 

belt built into the backrest for the seat next to the 
driver’s seat.

For more information on the 

Seat belts

, 

refer to the corresponding section.

Under-seat storage

 

 

If the vehicle is so equipped, a storage space is 
provided under the seat.

►  Pull the strap towards you to tip the seat 

cushion.

Armrest

 

 

The armrest has notches.

►  Pull the armrest fully up

►  Lower it fully down.

►  Raise the armrest to the desired position.

14/02/2022   15:33:11

50

Ease of use and comfort

Heated seats and bench 
seat

 

 

 

 

 

 

If fitted to your vehicle.

►  With the engine running and when the 

outside temperature is below 20 °C, use the 
adjustment knob to switch on and select the level 
of heating required from 

0

 (off) to 

3

 (high).

Prolonged use of heated seats is not 
recommended for people with sensitive 

skin.
There is a risk of burns for people whose 
perception of heat is impaired (e.g. illness, 
taking medication).
To keep the heated pad intact and to prevent 
a short circuit:
–  Do not place heavy or sharp objects on the 
seat.
–  Do not kneel or stand on the seat.
–  Do not spill liquids onto the seat.
–  Never use the heating function if the seat 
is damp.

Do not use the function when the seat 
is not occupied.

Reduce the heating intensity as soon as 
possible.
When the seat and passenger compartment 
have reached a satisfactory temperature, 

switch the function off; reducing electrical 

consumption in turn decreases energy 
consumption.

Electric lumbar 
adjustment

 

 

►  Press the control to obtain the desired lumbar 

support.

Massage function

 

 

14/02/2022   15:33:11

51

Ease of use and comfort

3

This function provides lumbar massage; it only 
operates when the engine is running as well as 
in STOP mode of the Stop & Start system.

Activation/Deactivation

►  Press this button to activate/deactivate 

the function.

Upon activation, the indicator lamp comes on. 
The massage function is activated for a period 
of one hour.
During this time, massage is performed in 
6 cycles of 10 minutes (6 minutes of massage 
followed by a 4-minute break).
After one hour, the function is deactivated; the 

indicator lamp goes off.

Adjustment of intensity

 

 

Press this button to adjust the intensity of 
the massage.

Two levels of massage are available.

Steering wheel 
adjustment

 

 

► 

When stationary

, lower the control lever to 

release the steering wheel.

►  Adjust the height and reach.

►  Pull the control lever to lock the steering 

wheel.

As a safety precaution, these operations 

must only be carried out while the vehicle 

is stationary.

Mirrors

Door mirrors

As a safety measure, the mirrors should 

be adjusted to reduce the "blind spots".

The objects that you see in the mirrors are 
in fact closer than they appear. Take this 

into account in order to correctly judge the 
distance of vehicles approaching from behind.

 

 

►  Move control 

A

 to the right or to the left to 

select the corresponding mirror.

►  Move control 

B

 in any of the four directions 

to adjust.

►  Return control 

A

 to its central position.

Manual folding

The mirrors can be folded manually (parking 
obstruction, narrow garage, etc.).

►  Turn the mirror towards the vehicle.

Electric folding

Depending on equipment, the door mirrors can 
be folded electrically.

►  From the inside, with the 

ignition on, place control 

A

 in the 

central position.

►  Pull control 

A

 backwards.

14/02/2022   15:33:12