Fiat Ulysse (2022 year). Manual in english - page 2

20

Dashboard instruments

indicating the driving range in miles or 
kilometres.
While driving, the message is displayed every 30 
seconds. The alert is repeated when switching 
on the ignition.
You can continue driving for up to 685 miles 
(1,100 km) before the 

engine starting 

prevention

 system is triggered.

Have it checked by a Fiat Dealership or a 

qualified workshop.

Starting prevented

Every time the ignition is switched on, the 
message "

Emissions control fault: Starting 

prevented

" or "

NO START IN

" is displayed.

To restart the engine

Contact a Fiat Dealership or a qualified 

workshop.

Power 

indicator (Electric)

 

 

CHARGE

Traction battery charging during deceleration 
and braking.

ECO

Moderate energy consumption and optimised 
driving range.

POWER

Energy consumption by the drive train during 
acceleration.

NEUTRAL

When the ignition is switched on, the vehicle’s 
electric drive train neither consumes nor 
generates energy; after sweeping over the 
indicator, the needle returns to its "neutral" 
position: between ECO and CHARGE.

With the ignition off, opening the driver's 

door activates the indicator, which moves 

to the "neutral" position: between ECO and 
CHARGE.

Charge level indicator 

(Electric)

 

 

The traction battery's actual charge level and 
the remaining range are displayed continuously 
when the vehicle is started.

With the ignition off, opening the driver's 

door activates the indicator.

Associated warning lamps

Two successive alert levels indicate that the 
energy available has dropped to a low level:

1st level: Reserve

0 %

100

The state of charge of the traction battery 
is low.

14/02/2022   15:33:02

21

Dashboard instruments

1

Fixed LED and needle in the red zone, 
accompanied by an audible signal.

►  View the remaining range on the instrument 

panel.

►  Put the vehicle on charge as soon as 

possible.

2nd level: Critical

The state of charge of the traction battery 
is critical.

Fixed, together with the reserve LED, 
accompanied by an audible signal.

►  You must put the vehicle on charge.

The remaining range is no longer 
calculated. The drive train power 

gradually decreases.
The heating and air conditioning are switched 

off (even if the needle indicating their 

consumption is not at the "

ECO

" position). 

Thermal comfort 

consumption indicator 

(Electric)

 

 

The gauge shows the consumption of the 
traction battery's electrical energy by the thermal 
comfort devices in the passenger compartment.
The devices in question are the heating and air 
conditioning systems.
This equipment can be used:
–  If the vehicle is not plugged in, when the 

READY

 lamp is lit.

–  If the vehicle is plugged in, when the ignition is 
switched on ("Lounge" mode).
Selecting 

ECO

 mode limits the performance 

of some of this equipment. The needle on the 
thermal comfort consumption indicator then 
moves into the "

ECO

" zone.

To quickly heat or cool the passenger 
compartment, feel free to temporarily 

select the maximum heating or cooling 
setting.
When the heating is on maximum, the gauge 
on the thermal comfort consumption indicator 
is in the 

MAX

 zone. When the air conditioning 

is on maximum, it stays in the 

ECO

 zone.

Excessive use of thermal comfort equipment, 

particularly at low speed, can significantly 

decrease the vehicle's range.
Remember to optimise equipment settings 
upon achieving the desired level of comfort, 
and adjust them if necessary whenever you 
start the vehicle.
After an extended period without using the 
heating, you may notice a slight odour during 

the first few minutes of use.

Distance recorders

The total and trip distances are displayed for 

thirty seconds when the ignition is switched off, 

when the driver's door is opened and when the 
vehicle is locked or unlocked.

14/02/2022   15:33:02

22

Dashboard instruments

Total distance recorder

 

 

 

 

This measures the total distance travelled by the 
vehicle since its initial registration.

Trip distance recorder (Diesel)

 

 

 

 

This measures the distance travelled since it was 
last reset by the driver.

Resetting the trip recorder

 

 

►  With the ignition on, press the button until 

zeros appear.

Lighting dimmer

This system allows the brightness of the 
instruments and controls to be adjusted manually 
to suit the ambient light level.

With buttons

 

 

 

 

With the lamps on, press button 

A

 to increase 

the brightness of the lighting, or button 

B

 to 

decrease it.
Release the button when the desired brightness 
is reached.

With touch screen

 

 

►  In the 

Settings

 menu, select "

Brightness

" 

or "

OPTIONS

", "

Screen configuration

" then 

"

Brightness

".

►  Adjust the brightness by pressing the arrows 

or moving the slider.

The brightness can be set differently for 

day mode and night mode.

Trip computer

Displays information related to the current trip 
(range, fuel consumption, average speed, etc.).

Information 

display

To display the various trip computer tabs in turn:

14/02/2022   15:33:03

23

Dashboard instruments

1

 

 

 

 

►  Press the button located on the end of the 

wiper control stalk

.

With steering-mounted controls

 

 

►  Press the knob on the 

steering wheel

.

On the instrument panel

 

 

 

 

►  Press this button.

The following current information is shown in 
turn:
–  Driving range (Diesel).

–  Current consumption.
–  Stop & Start time counter (Diesel).
–  Trip "

1

" followed by (depending on version) 

trip "

2

" including average speed, average 

consumption and distance travelled for each trip.
Trips "

1

" and "

2

" are independent but their use 

is identical.
For example, trip "

1

" can be used for daily 

figures and trip "

2

" for monthly figures.

Trip reset

The reset is performed when the trip counter is 
displayed.

 

 

 

 

►  Press the button on the end of the 

wiper 

control stalk

 for more than two seconds.

 

 

►  Press the knob on the 

steering wheel

 for 

more than two seconds.

 

 

 

 

►  Press this button for more than 2 seconds.

Definitions

Range

(miles or km)
(Traction battery charge level percentage) 
(Electric)

Distance that can still be travelled with the 
fuel remaining in the tank (based on the 

average fuel consumption over the last few miles 
(kilometres) travelled).
This value may vary following a change in driving 

style or terrain, leading to a significant change in 

current fuel consumption.

When the range falls below 19 miles (30 km), 

dashes are displayed.

After filling with at least 5 litres of fuel, the range 

is recalculated and is displayed if it exceeds 62 
miles (100 km).
Dashes appearing permanently in place of 
numbers while driving indicates a malfunction.

14/02/2022   15:33:03

24

Dashboard instruments

Contact a Fiat Dealership or a qualified 

workshop.

Current consumption

(mpg or l/100 km or km/l)
(miles/kWh or kWh/100 km or km/kWh) (Electric)

/

Calculated during the last few 
seconds.

This function is only displayed at speeds above 

19 mph (30 km/h) (Diesel).

Average consumption

(mpg or l/100 km or km/l)
(miles/kWh or kWh/100 km or km/kWh) (Electric)

/

Calculated since the last trip 
computer reset.

Average speed

(mph or km/h)

Calculated since the last trip computer 
reset.

Distance travelled

(miles or km)

Calculated since the last trip computer 
reset.

Stop & Start time counter

(minutes/seconds or hours/minutes) 

If your vehicle is fitted with the Stop & Start 

function, a time counter calculates the time spent 
in STOP mode during a journey.

The time counter is reset each time the ignition is 
switched on.

Touch screen

This system gives access to the following 
elements:
–  Permanent display of the time and outside 
temperature (a blue warning lamp appears if 
there is a risk of ice).
–  Vehicle functions and equipment setting 
menus.
–  Audio system and telephone controls and 
display of related information.
–  Display of visual manoeuvring aid functions
–  Internet services and display of related 
information.
–  Navigation system controls and 
display of related information (depending on 
version).

For safety reasons, always stop the 

vehicle before performing operations 

that require sustained attention.

Some functions are not accessible while 
driving.

Recommendations

This screen uses capacitive sensing technology.
–  Do not use pointed objects on the touch 
screen.
–  Do not touch the touch screen with wet hands.

–  Use a soft, clean cloth to clean the touch 
screen.

Principles

►  Use the buttons on each side of the touch 

screen to access the menus, then press the 
buttons that appear on the touch screen.
Some menus may display across two pages: 
press the "

OPTIONS

" button to access the 

second page.

After a few moments with no action on 

the second page, the first page is 

displayed automatically.

To deactivate/activate a function, select "

OFF

" 

or "

ON

".

Configuring a function

 

Access to additional information on the 

function

Confirm

 

Return to the previous page or confirm

 

Menus

 

 

14/02/2022   15:33:04

25

Dashboard instruments

1

Press the touch screen with three fingers 

to show all of the menu buttons.

For more information about the menus, 
refer to the sections describing the audio 

and telematics systems.

Radio/Media

 

Navigation

 (Depending on equipment) 

Driving or Vehicle

 (Depending on 

equipment)

Activation, deactivation and settings for certain 
functions.
The functions are organised in 2 tabs: "

Driving 

functions

" and "

Vehicle settings

".

Telephone

 

Applications

Display of available connected services.

Energy

Access the specific Electric functions 

(energy flow, consumption statistics, deferred 

charge) organised in the corresponding 3 tabs.
or

Settings

Main settings for the audio system and 

touch screen.

Audio system on/off

Volume adjustment/mute

Upper bar

Certain information is displayed permanently in 
the upper bar of the touch screen:
–  Time and outside temperature (a blue warning 
lamp appears if there is a risk of ice).
–  Reminder of information from the 

RadioMedia

 and 

Telephone

 menus and 

navigation instructions (depending on 
equipment).

–  Notifications.

–  Access to the 

Settings

. 

Energy menu (Electric)

Depending on version, this is accessible either:

–  directly, by pressing the button near the 
touch screen.
–  via the 

Applications

 menu. 

Flow

The page displays a real-time representation of 
the electric drive train’s operation.

 

 

1.

Active driving mode

2.

Electric motor

3.

Estimated traction battery charge level

4.

Energy flows

The energy flows have a specific colour for each 

type of driving:

A.

Blue: energy consumption

B.

Green: energy recovery

Statistics

This page shows electrical energy consumption 
statistics.

 

 

–  Blue bar chart: directly consumed energy 
supplied by the traction battery.
–  Green bar chart: energy recovered during 
deceleration and braking, used to recharge the 
battery.
The average result for the current trip is stated in 
kWh/100 km.

►  You can change the displayed time scale by 

pressing the 

-

 or 

+

 buttons.

A current trip is any trip of more than 20 

minutes without switching off the ignition.

14/02/2022   15:33:05

26

Dashboard instruments

Charging

This page allows you to programme deferred 
charging.
For more information on 

Charging the traction 

battery (Electric)

, refer to the corresponding 

section.

Setting the date and time

With audio system

►  Press the 

MENU

 button for access to the 

main menu

.

►  Press the "

7

" or "

8

" button to select the 

"

Personalisation-configuration

" menu, then 

confirm by pressing the 

OK

 button.

►  Press the "

5

" or "

6

" button to select the 

Display configuration

 menu, then confirm by 

pressing the 

OK

button.

►  Press the "

5

" or "

6

" and "

7

" or "

8

" buttons 

to adjust the date and time values, then confirm 

by pressing the 

OK

 button.

With Connect Radio

►  Select the 

Settings

 menu in the upper 

banner of the touch screen.

►  Select "

Configuration

".

►  Select "

Date and time

". 

►  Select "

Date

" or "

Time

".

►  Choose the display formats.

►  Change the date and/or time using the 

numeric keypad.

►  Confirm with "

OK

".

With Connect Nav

Time and date settings are only available if GPS 
synchronisation is deactivated.

►  Select the 

Settings

 menu in the 

banner of the touch screen.

►  Press the "

OPTIONS

" button to access the 

secondary page.

►  Select "

Setting the time-date

". 

►  Select the "

Date:

" or "

Time

" tab.

►  Set the date and/or time using the numeric 

keypad.

►  Confirm with "

OK

".

Additional settings

You can choose:
–  To change the time zone.
–  To change the display format of the date and 
time (12h/24h).
–  To activate or deactivate the summer time 
management function (+1 hour).
–  To activate or deactivate GPS synchronisation 
(UTC).

The system does not automatically 
change between winter and summer time 

(depending on the country of sale).

14/02/2022   15:33:05

27

Access

2

Electronic key with 
remote control function 
and built-in key

Advice

If one of the doors or the boot is still open 
or if the electronic key for the Keyless 

Entry and Start  system has been left inside 
the vehicle, central locking will not take place.

However, if the vehicle is fitted with an alarm, 

it will be activated after 45 seconds.

If the vehicle is unlocked but the doors or 
boot are not subsequently opened, the 

vehicle will automatically lock itself again after 

about 30 seconds. If the vehicle is fitted with 

an alarm, it will be reactivated automatically.

Automatic door mirror folding and 

unfolding can be deactivated by a Fiat 

Dealership or a qualified workshop.

As a safety measure, never leave the 

vehicle, even for a short time, without 

taking the Keyless Entry and Start system’s 
electronic key with you.
Be aware of the risk of theft of the vehicle if 

the key is present in one of the defined areas 

while the vehicle is unlocked.

If a door is not properly closed (except the 
right-hand door with side-hinged rear 

doors):
–  when the vehicle is stationary and engine 
running, this warning lamp comes on, 
accompanied by a warning message for a few 
seconds, 
–  when the vehicle is moving (at speeds above 
6 mph (10 km/h)), this warning lamp comes on, 
accompanied by an audible signal and a warning 
message for a few seconds.

Remote control key

This allows the central locking or unlocking of the 
vehicle using the door lock or from a distance.
It also allows the vehicle to be located, the fuel 

filler cap and charging flap to be opened and 

closed and the engine to be started or switched 

off, as well as providing protection against theft.

The remote control buttons are not active 
with the ignition switched on.

Unfolding / Folding the key

 

 

►  Press this button to unfold or fold the key.

The remote control may be damaged if 
you do not press the button.

Keyless Entry and Start

This allows the central locking or unlocking of the 
vehicle from a distance. 
It is also used to locate and start the vehicle, as 
well as providing protection against theft.

Integral key

This is used to lock and unlock the vehicle when 
the remote control cannot operate:

–  cell battery flat, vehicle battery discharged or 

disconnected, etc.
–  vehicle located in an area with strong 
electromagnetic signals.

 

14/02/2022   15:33:05

28

Access

 

►  Keep this button 

1

 pulled while removing 

key 

2

 from the housing.

If the alarm is activated, the audible 
signal triggered on opening a door with 

the key (integral with the remote control) will 
stop when the ignition is switched on.

Once the built-in key is ejected, always 
keep it with you to be able to carry out 

the corresponding back-up procedures.

"Keyless Entry and Start" on your 

person

 

 

It allows the unlocking, locking and starting of the 
vehicle while carrying the remote control on your 
person in recognition zone "

A

".

In the ignition on (accessories) position, 
with the "START/STOP" button, the 

hands-free function is deactivated and it is 
impossible to open the doors.
For more information on 

Starting/switching 

off the engine, Keyless Entry and Start

 and 

in particular the "ignition on" position, refer to 
the corresponding section.

Locating the vehicle

This function helps you to spot your vehicle from 
a distance, with the vehicle locked:

–  The direction indicators flash for approximately 

10 seconds.
–  The courtesy lamps come on.

►  Press this button.

 

Remote operation of lighting

If fitted to the vehicle.

A short press on this button switches on 

the lighting remotely (lighting of 

sidelamps, dipped beam headlamps and number 
plate lamps).
A second press on the button before the end of 
the timed period cancels the remote lighting.

Advice

Remote control

The remote control is a sensitive, high-

frequency device; avoid handling it in your 
pocket, due to the risk of unintentionally 
unlocking the vehicle.
Avoid pressing the remote control buttons 
while out of range of the vehicle, due to 
the risk of rendering the remote control 
inoperative. It would then be necessary to 
reset it.
The remote control does not work when the 
key is in the ignition switch, even when the 

ignition is switched off.

Anti-theft protection

Do not modify the electronic vehicle 

immobiliser, as this might result in 
malfunctions.
For vehicles with a key ignition switch, 
remember to remove the key and turn the 
steering wheel to engage the steering lock.

Locking the vehicle

Driving with the doors locked could make 

it more difficult for the emergency services 

to enter the passenger compartment in an 
emergency.
As a safety precaution, remove the key from 
the ignition or take the electronic key with you 
when leaving the vehicle, even for a short 
time.

14/02/2022   15:33:06

29

Access

2

Purchasing a second-hand vehicle

Have the key codes memorised by a Fiat 

Dealership, to ensure that the keys in your 
possession are the only ones able to start the 
vehicle.

To preserve the battery charge in the 
electronic key and the vehicle's battery, 

the "hands-free" functions are set to 
hibernation mode after 21 days without use. 
To restore these functions, press one of the 
remote control buttons or start the engine with 
the electronic key in the reader.
For more information on starting with the 
Keyless Entry and Start system, refer to the 
corresponding section.

Electrical interference

The electronic key may not work if it is 

close to an electronic device (e.g. mobile 
telephone (switched on or on standby), laptop 

computer, strong magnetic fields). If this 

occurs, move the electronic key away from 
the electronic device.

Accumulations (water, dust, grime, salt, 

etc.) on the inner surface of the door 

handle may affect detection.

If cleaning the inner surface of the door 
handle using a cloth does not restore 
detection, contact a Fiat Dealership or a 

qualified workshop.

A sudden splash of water (stream of water, 
high pressure jet washer, etc.) may be 

identified by the system as the desire to open 

the vehicle.

Unlocking/Complete or 
selective unlocking

What is the purpose of total 

or selective unlocking?

 

 

 

 

Total unlocking unlocks 

all

 the vehicle’s doors 

(front, side and rear).

 

 

Selective unlocking unlocks either the 

cab

 doors, 

or the doors of the 

loading area

 (side and rear).

The separated unlocking system 
between 

cab

 and 

loading area

 is a 

security measure. This prevents access to the 
part of the vehicle where the driver is not 
present.

Activation/Deactivation

 

 

 

 

►  To 

activateselective

 unlocking 

between the 

cab

 and the 

loading 

area

 or to 

deactivate

 selective unlocking and 

return to 

total

 unlocking mode, switch on the 

ignition and press this button for more than two 
seconds.
An audible signal and, depending on equipment, 

a display message, confirm that the request has 

been acknowledged.

Selective unlocking between 

cab

 and 

loading area

 is activated by default.

14/02/2022   15:33:06

30

Access

Unlocking/Complete 

unlocking

Unlocking is signalled by rapid flashing of 

the direction indicators for a few 

seconds.
Depending on version, the door mirrors unfold 
and the alarm is deactivated.

With the key

►  To unlock the vehicle 

fully

, turn the key in the 

front left-hand door lock towards the front of the 
vehicle.
If the vehicle has an alarm, it will not be 
deactivated. Opening a door will trigger the 
alarm, which can be stopped by switching the 
ignition on.

With the remote control

►  Depending on equipment, 

press one of these buttons to 

unlock the vehicle.

Using the remote control with electric 

sliding side door(s)

►  To 

fully

 unlock the vehicle and open 

the side door, press and hold this button 

until the door has opened.

With Keyless Entry and Start on your 

person

To unlock the vehicle, the remote control must be 
in recognition zone 

A

.

►  To unlock the vehicle 

fully

, pass your hand 

behind one of the door handles (front door(s), 
manual sliding side door(s) or left-hand side-
hinged door) and then pull the handle to open 
the corresponding door.

With electric sliding side door(s)

 

 

►  With the Keyless Entry and Start on your 

person, pass your hand behind the handle 
to unlock the vehicle, then pull and release 
the handle. This action also causes the 
corresponding door to open.

With tailgate

 

 

►  With the Keyless Entry and Start on your 

person, to unlock the 

vehicle

, pull the tailgate 

handle and then lift it up to open it.

With an opening rear screen in the tailgate

 

 

►  With the Keyless Entry and Start on your 

person, to unlock the vehicle, press the tailgate 
opening rear screen unlocking control. The 
screen will open slightly; then, lift it up to open it.

14/02/2022   15:33:07

31

Access

2

Selective unlocking

 

 

Unlocking is signalled by rapid flashing of 

the direction indicators for a few 

seconds.
Depending on version, the door mirrors unfold 
and the alarm is deactivated.

With the remote control

►  To unlock the 

cabin

 doors alone, 

press this button 

once

.

►  To unlock the side and rear doors of the 

loading area

, press this button a 

second time

.

If the vehicle is fitted with this function:

►  Press this button to unlock the 

loading area

 only.

Using the remote control with electric 

sliding side door(s)

►  To unlock the 

loading area

 alone 

without opening the side door, press the 

relevant door button or keep the button pressed 
down to open the door.

With Keyless Entry and Start on your 

person

 

 

►  To unlock the 

cabin

 alone, pass your hand 

behind a handle of the front left or right doors, 
then pull the handle to open the door.

The door locking state of the 

loading 

area

 remains unchanged.

 

 

►  To unlock the loading area alone, the remote 

control on your person in 

recognition zone

 

A

, 

B

 

or 

C

, pass your hand behind a handle of the front 

left or right doors, then pull the handle to open 
the corresponding door.

Depending on the version, the door 
mirrors unfold only when the cabin is 

unlocked, the alarm is deactivated.

With electric sliding side door(s)

 

 

►  With the Keyless Entry and Start on your 

person, pass your hand behind the left-hand or 
right-hand door handle to unlock the 

loading 

area

, then pull and release the handle. This 

action also causes the corresponding door to 
open.

With tailgate

 

 

14/02/2022   15:33:07

32

Access

►  With the Keyless Entry and Start on your 

person, to unlock the 

loading area

, pull the 

tailgate handle and then lift it up. 

Unlocking is signalled by rapid flashing of 

the direction indicators for a few 

seconds. 

Locking

With the key

►  To lock the vehicle 

fully

, turn the key in the 

front left-hand door lock towards the rear of the 
vehicle.
If your vehicle has an alarm, it will not be 
activated.

With the remote control

►  To lock the vehicle 

completely

, press 

this button.

With Keyless Entry and 

Start on your person

To lock the vehicle, the remote control must be in 
recognition zone 

A

.

 

 

►  To lock the vehicle, press the markings on 

one of the door handles (front door(s), manual 
sliding side door(s) or left-hand side-hinged 
door).

With electric sliding side door(s)

►  With the Keyless Entry and Start on your 

person, to lock the vehicle 

fully

, press the 

markings on one of the 

front

 door handles.

With tailgate

 

 

►  With the Keyless Entry and Start on your 

person, press the tailgate locking control to lock 
the vehicle.

Depending on version, keeping 
the locking controls depressed 

closes the windows. If the control is released, 
the window stops in its current position.

Ensure that no person or object might 
prevent the windows from closing 

properly.
Pay particular attention to children when 
operating windows.

If the vehicle is not fitted with an alarm, 

locking is signalled by fixed lighting of the 

direction indicators for approximately two 
seconds. 
Depending on version, the door mirrors fold at 
the same time.

Driving with the doors locked could make 

it more difficult for the emergency 

services to enter the passenger compartment 
in an emergency.
As a safety measure, never leave the vehicle 
without taking the remote control with you, 
even for a short time.

Deadlocking

Deadlocking deactivates the exterior and 
interior door controls, as well as the 

central locking button on the dashboard.
The horn remains operational.
You must therefore never leave anyone inside 
the vehicle when it is deadlocked.

With the key

►  To deadlock the vehicle, turn the key in the 

front left-hand door lock towards the rear of the 
vehicle.

►  Then, 

within five seconds

, turn the key 

towards the rear again.

14/02/2022   15:33:07

33

Access

2

With the remote control

►  To deadlock the vehicle, press this 

button.

►  Then 

within five seconds after locking

, 

press this button again.

Depending on version, the electric door 
mirrors fold at the same time.

If the vehicle is not fitted with an alarm, 

deadlocking is confirmed by fixed 

illumination of the direction indicators for 
about two seconds.

With Keyless Entry and Start on your 

person

To lock the vehicle, the remote control must be in 
recognition zone 

A

.

 

 

►  To lock the vehicle 

fully

, press the markings 

on one of the door handles (front door(s), 
manual sliding side door(s) or left-hand side-
hinged door).

►  To deadlock the vehicle, press the markings 

again 

within five seconds.

With electric sliding side door(s)

►  With the Keyless Entry and Start on your 

person, to lock the vehicle 

fully

, press the 

markings on one of the 

front

 door handles.

►  To deadlock the vehicle, press the markings 

again 

within five seconds.

With tailgate

 

 

►  With the Keyless Entry and Start on your 

person, press the tailgate locking control to lock 
the 

entire

 vehicle.

►  To deadlock the vehicle, press the control 

again 

within five seconds

.

If the vehicle is not fitted with an alarm, 

deadlocking is signalled by fixed lighting 

of the direction indicators for approximately 
two seconds.

Back-up procedures

Lost keys, remote control, 

electronic key

Go to a Fiat Dealership with the vehicle's 

registration certificate, your personal 

identification documents and if possible, the label 

bearing the key code.
The Fiat Dealership will be able to retrieve the 
key code and the transponder code, enabling a 
new key to be ordered.

Complete unlocking/locking 

of the vehicle with the key

Use this procedure in the following situations:
–  Remote control battery discharged.
–  Remote control malfunction.
–  Vehicle battery discharged.
–  Vehicle in an area subject to strong 
electromagnetic interference.

In the first case, change the remote control 

battery.
In the second case, reinitialise the remote 
control.
Refer to the corresponding sections.

►  Insert the key into the door lock.

►  Turn the key towards the front/rear to unlock/

lock the vehicle.

►  Turn the key towards the rear again within 

5 seconds to deadlock the vehicle.

If the vehicle is fitted with an alarm, it will 

not be activated when locking with the 

key.
If the alarm is activated, the siren sounds 
when the door is opened; switch on the 
ignition to stop it.

14/02/2022   15:33:07

34

Access

If the vehicle is unlocked with the key in 
the lock 

after locking it with the remote 

control or the Keyless Entry and Start 

system

, 

all doors and the boot

 are 

unlocked.
If the vehicle is unlocked with the key in the 
lock 

after locking it with the key

, only the 

doors (front door and sliding side door(s)) are 
unlocked. The side-hinged doors and tailgate 
are not unlocked. Switching on the ignition 
unlocks them.

Central locking not 

functioning

Use these procedures in the following cases:
–  Central locking malfunction.
–  Battery disconnected or discharged.

In the event of a malfunction of the 
central locking system, the battery must 

be disconnected to ensure that the vehicle is 
locked fully.

Front left-hand door

►  Insert the key into the door lock.

►  Turn the key towards the rear of the vehicle 

to lock it, or towards the front to unlock it.

Front passenger door and sliding 

side door

Unlocking

►  Pull the interior door opening handle.

Locking

►  Open the door.

►  For the side door, check that the child lock is 

not on. Refer to the corresponding section.

 

 

Front passenger door

 

 

Sliding side door

►  Remove the black cap on the edge of the 

door, using the key.

►  Insert the key in the aperture without 

forcing it, then without turning it, move the latch 
sideways towards the inside of the door.

►  Remove the key and refit the black cap.

►  Close the doors and check from the outside 

that the vehicle is locked.

Side-hinged doors

Unlocking

►  Use the interior opening handle.

Locking

►  If fitted to your vehicle, check that the electric 

child lock is not on.

►  Open the left-hand side-hinged door.

 

 

►  Insert the key into the latch aperture on the 

edge of the door (without forcing it) and slide the 
assembly upwards.

►  Remove the key.

►  Close the door and check from the outside 

that the vehicle is locked. 

Unlocking the tailgate

 

 

►  From inside the vehicle, insert a small 

screwdriver into hole 

A

 on the lock to unlock the 

tailgate.

►  Move the latch to the left.

If the fault persists after closing again, 
the tailgate will remain locked.

14/02/2022   15:33:08

35

Access

2

Changing the battery

If the battery is flat, this warning lamp 

comes on, accompanied by an audible 

signal and the display of a message.

Battery type: CR2032/3 volts.

 

 

►  Unclip the cover by inserting a small 

screwdriver in the slot and lift the cover.

►  Remove the flat battery from its housing.

►  Put the new battery in place, respecting the 

polarity. Start by inserting it into the contacts 
located in the corner, then clip the cover onto 
the unit.

►  Reinitialise the remote control.

For more information on 

Reinitialising the 

remote control

, refer to the corresponding 

section.

Do not throw remote control batteries 
away, as they contain metals that are 

harmful to the environment. Take them to an 
approved disposal point.

Reinitialising the remote 

control

Following replacement of the battery or in 
the event of a fault, it may be necessary to 
reinitialise the remote control.

Without Keyless Entry and Start

 

 

►  Switch the ignition off.

►  Turn the key to position 

2 (Ignition on)

.

►  Immediately press the closed padlock button 

for a few seconds.

►  Switch off the ignition and remove the key 

from the ignition switch.
The remote control is now fully operational 
again.

 

 

►  Insert the mechanical key (incorporated into 

the remote control) into the lock to open the 
vehicle.

►  Place the electronic key against the back-up 

reader on the steering column and hold it there 
until the ignition is switched on.

► 

With a manual gearbox,

 place the gear lever 

in neutral then fully depress the clutch pedal.

► 

With an automatic gearbox or drive 

selector

, while in mode 

P

, depress the brake 

pedal.

►  Switch on the ignition by pressing the 

"

START/STOP

" button.

If the fault persists after reinitialisation, contact a 

Fiat Dealership or a qualified workshop without 

delay.

14/02/2022   15:33:08