Dodge Grand Caravan (2020 year). Manual in english

MULTIMEDIA

311

Redial
To redial the last number called from your

mobile phone using Voice Command:

1. Push the Phone button to begin.

2. After the “Ready” prompt and the following

beep, say “Redial.”



The Uconnect Phone will call the last

number that was dialed from your mobile

phone.

NOTE:

This may not be the last number dialed from the

Uconnect Phone.

Call Continuation
Call continuation is the progression of a phone

call on the Uconnect Phone after the vehicle

ignition has been switched to OFF. Call contin

uation functionality available on the vehicle can

be any one of three types:

1. After the ignition is switched to OFF, a call

can continue on the Uconnect Phone either

until the call ends, or until the vehicle

battery condition dictates cessation of the

call on the Uconnect Phone and transfer of

the call to the mobile phone.

2. After the ignition is cycled to OFF, a call can

continue on the Uconnect Phone for a

certain duration, after which the call is

automatically transferred from the

Uconnect Phone to the mobile phone.

3. An active call is automatically transferred to

the mobile phone after the ignition is cycled

to OFF.

Uconnect Phone Features

Language Selection
To change the language that the Uconnect

Phone is using:



Push the Phone button to begin.



After the “Ready” prompt and the following

beep, say the name of the language you wish

to switch to / English, Spanish, or French.



Continue to follow the system prompts to

complete the language selection.

After selecting one of the languages, all

prompts and voice commands will be in that

language.

NOTE:

After every Uconnect Phone language change

operation, only the language-specific 32-name

phonebook is usable. The paired phone name is

not language-specific and usable across all

languages.

Emergency Assistance
If you are in an emergency and the mobile

phone is reachable:



Pick up the phone and manually dial the

emergency number for your area.

If the phone is not reachable and the Uconnect

Phone is operational, you may reach the

emergency number as follows:



Push the Phone button to begin.



After the “Ready” prompt and the following

beep, say “Emergency” and the Uconnect

Phone will instruct the paired mobile phone

to call the emergency number.

312

MULTIMEDIA

NOTE:



The emergency number dialed is based on

the country where the vehicle is purchased

(911 for the US and Canada and 060 for

Mexico). The number dialed may not be appli

cable with the available mobile service and

area.



If supported, this number may be program

mable on some systems. To do this, push the
Phone button and say “Setup,” followed

by “Emergency.”



The Uconnect Phone does slightly lower your

chances of successfully making a phone call.

Roadside Assistance/Towing Assistance
If you need roadside assistance:



Push the Phone button to begin.



After the “Ready” prompt and the following

beep, say “Towing Assistance”.

NOTE:

You should program the desired Towing

Assistance phone number using the Voice

Command system. To do this, push the Phone
button and say “Setup,” followed by “Towing

Assistance.” When prompted say

1-800-521-2779 for U.S., 1-800-363-4869 for

Canada, 55-14-3454 for Mexico City and

1-800-712-3040 for outside Mexico City in

Mexico.

Paging
To learn how to page, refer to “Working With

Automated Systems.” Paging works properly

except for pagers of certain companies, which

time out a little too soon to work properly with

the Uconnect Phone.

Voice Mail Calling
To learn how to access your voice mail, refer to

“Working With Automated Systems.”

Working With Automated Systems
This method is used in instances where one

generally has to press numbers on the mobile

phone keypad while navigating through an

automated telephone system.
You can use your Uconnect Phone to access a

voice mail system or an automated service,

such as a paging service or automated

customer service line. Some services require

immediate response selection. In some

instances, that may be too quick for use of the

Uconnect Phone.
When calling a number with your Uconnect

Phone that normally requires you to enter in a

touch-tone sequence on your mobile phone

keypad, you can push the Voice Recognition
button and say the sequence you wish to

enter, followed by the word “Send.” For

example, if required to enter your PIN followed

with a pound, (3 7 4 6 #), you can push the
Voice Recognition button and say, “3 7 4 6 #

Send.” Saying a number, or sequence of

numbers, followed by “Send,” is also to be used

for navigating through an automated customer

service center menu structure, and to leave a

number on a pager.

WARNING!

To use your Uconnect Phone System in an

emergency, your mobile phone must be:



Turned on.



Paired to the Uconnect System.



Have network coverage.

MULTIMEDIA

313

You can also send stored Uconnect Phonebook

entries as tones for fast and easy access to

voice mail and pager entries. To use this

feature, dial the number you wish to call and
then push the Voice Command button and

say, “Send.” The system will prompt you to enter

the name or number and say the name of the

phonebook entry you wish to send. The

Uconnect Phone will then send the

corresponding phone number associated with

the phonebook entry, as tones over the phone.

NOTE:



You may not hear all of the tones due to

mobile phone network configurations. This is

normal.



Some paging and voice mail systems have

system time out settings that are too short

and may not allow the use of this feature.

Barge In – Overriding Prompts
The “Voice Command” button can be used

when you wish to skip part of a prompt and

issue your voice command immediately. For

example, if a prompt is asking “Would you like

to pair a phone, clear a...,” you could push the
Voice Recognition button and say, “Pair a

Phone” to select that option without having to

listen to the rest of the voice prompt.

Turning Confirmation Prompts On/Off
Turning confirmation prompts off will stop the

system from confirming your choices (e.g., the

Uconnect Phone will not repeat a phone

number before you dial it).
To turn confirmation prompts on or off using

Voice Command:

1. Push the Phone button to begin.

2. After the “Ready” prompt and the following

beep, say:



“Setup Confirmations Prompts On” or



“Setup Confirmations Prompts Off”

Phone And Network Status Indicators
If available on the radio and/or on a premium

display such as the instrument panel cluster,

and supported by your mobile phone, the

Uconnect Phone will provide notification to

inform you of your phone and network status

when you are attempting to make a phone call

using Uconnect Phone. The status is given for

roaming, network signal strength, phone battery

strength, etc.

Dialing Using The Mobile Phone Keypad
You can dial a phone number with your mobile

phone keypad and still use the Uconnect Phone

(while dialing via the mobile phone keypad, the

user must exercise caution and take precau

tionary safety measures). By dialing a number

with your paired Bluetooth® mobile phone, the

audio will be played through your vehicles audio

system. The Uconnect Phone will work the same

as if you dial the number using Voice Command.

NOTE:

Certain brands of mobile phones do not send

the dial ring to the Uconnect Phone to play it on

the vehicle audio system, so you will not hear it.

Under this situation, after successfully dialing a

number the user may feel that the call did not

go through even though the call is in progress.

Once your call is answered, you will hear the

audio.

314

MULTIMEDIA

Mute/Unmute (Mute ON/OFF)
When you mute the Uconnect Phone, you will

still be able to hear the conversation coming

from the other party, but the other party will not

be able to hear you. To mute the Uconnect

Phone:



Push the Voice Recognition button .



Following the beep, say “Mute.”

To unmute the Uconnect Phone:



Push the Voice Recognition button .



Following the beep, say “Mute off.”

Advanced Phone Connectivity

Transfer Call To And From Mobile Phone
The Uconnect Phone allows ongoing calls to be

transferred from your mobile phone to the

Uconnect Phone without terminating the call. To

transfer an ongoing call from your Uconnect

Phone paired mobile phone to the Uconnect

Phone or vice versa, push the Voice Recognition
button and say “Transfer Call.”

Connect Or Disconnect Link Between The

Uconnect Phone And Mobile Phone
Your mobile phone can be paired with many

different electronic devices, but can only be

actively "connected" with one electronic device

at a time.
If you would like to connect or disconnect the

Bluetooth® connection between a Uconnect

Phone paired mobile phone and the Uconnect

Phone, follow the instructions described in your

mobile phone user manual.

List Paired Mobile Phone Names



Push the Phone button to begin.



After the “Ready” prompt and the following

beep, say “Setup Phone Pairing”.



When prompted, say “List Phones”.



The Uconnect Phone will play the phone

names of all paired mobile phones in order

from the highest to the lowest priority. To

“Select” or “Delete” a paired phone being
announced, push the Voice Command

button and say “Select” or “Delete”. Also, see

the next two sections for an alternate way to

“Select” or “Delete” a paired phone.

Select Another Mobile Phone
This feature allows you to select and start using

another phone paired with the Uconnect Phone.



Push the Phone button to begin.



After the “Ready” prompt and the following

beep, say “Setup Select Phone” and follow

the prompts.



You can also push the Voice Recognition
button at any time while the list is being

played, and then choose the phone that you

wish to select.



The selected phone will be used for the next

phone call. If the selected phone is not avail

able, the Uconnect Phone will return to using

the highest priority phone present in or near

30 ft (9 m) of the vehicle.

Delete Uconnect Phone Paired Mobile Phones



Push the Phone button to begin.



After the “Ready” prompt and the following

beep, say “Setup Phone Pairing”.

MULTIMEDIA

315



At the next prompt, say “Delete” and follow

the prompts.



You can also push the Voice Recognition
button at any time while the list is being

played, and then choose the phone you wish

to delete.

Things You Should Know About Your

Uconnect Phone

Uconnect Phone Tutorial
To hear a brief tutorial of the system features,
push the Phone button and say “Uconnect

Tutorial.”

Voice Training
For users experiencing difficulty with the system

recognizing their voice commands or numbers,

the Uconnect Phone Voice Training feature may

be used. To enter this training mode, follow one

of the two following procedures:



From outside the Uconnect Phone mode

(e.g., from radio mode), push and hold the
Voice Recognition button for five seconds

until the session begins, or,



Push the Voice Recognition button and

say the “Voice Training,” “System Training,”

or “Start Voice Training” command.

You can either push the Uconnect Phone button

to restore the factory setting or repeat the

words and phrases when prompted by the

Uconnect Phone. For best results, the Voice

Training session should be completed when the

vehicle is parked with the engine running, all

windows closed, and the blower fan switched

off.
This procedure may be repeated with a new

user. The system will adapt to the last trained

voice only.

Reset
To Reset all settings using Voice Command:

1. Push the Phone button .

2. After the “Ready” prompt and the following

beep, say “Setup,” then “Reset.”



This will delete all phone pairing, phone

book entries, and other settings in all

language modes. The System will prompt

you before resetting to factory settings.

Voice Command
For best performance:



Adjust the rearview mirror to provide at least

1/2-inch (1 cm) gap between the overhead

console (if equipped) and the mirror.



Always wait for the beep before speaking.



Speak normally without pausing, just as you

would speak to a person sitting a few feet/

meters away from you.



Make sure that no one other than you is

speaking during a Voice Command period.

Performance is maximized under:



Low-to-medium blower setting



Low-to-medium vehicle speed



Low road noise



Smooth road surface



Fully closed windows



Dry weather condition

316

MULTIMEDIA

NOTE:



Even though the system is designed for users

speaking in North American English, French,

and Spanish accents, the system may not

always work for some.



When navigating through an automated

system such as voice mail, or when sending

a page, at the end of speaking the digit string,

make sure to say “Send.”



Storing names in the phonebook when the

vehicle is not in motion is recommended.



It is not recommended to store similar

sounding names in the Uconnect Phonebook.



Phonebook (Downloaded and Uconnect

Phone Local) name recognition rate is opti

mized when the entries are not similar.



Numbers must be spoken in single digits.

“800” must be spoken “eight-zero-zero” not

“eight hundred.”



You can say “O” (letter “O”) for “0” (zero).



Even though international dialing for most

number combinations is supported, some

shortcut dialing number combinations may

not be supported.

Far End Audio Performance
Audio quality is maximized under:



Low-to-medium blower setting



Low-to-medium vehicle speed



Low road noise



Smooth road surface



Fully closed windows



Dry weather conditions



Operation from the driver's seat



Performance, such as audio clarity, echo,

and loudness to a large degree relies on the

phone and network, and not the Uconnect

Phone



Echo at the phone far end can sometimes be

reduced by lowering the in-vehicle audio

volume

Recent Calls
If your phone supports “Automatic Phonebook

Download,” Uconnect Phone can list your

Outgoing, Incoming and Missed Calls.

SMS
Uconnect Phone can read or send new

messages on your phone.
Read Messages:
If you receive a new text message while your

phone is connected to Uconnect Phone, an

announcement will be made to notify you that

you have a new text message. If you wish to

hear the new message:

1. Push the Phone button .

2. After the “Ready” prompt and the following

beep, say “SMS Read” or “Read Messages”.



Uconnect Phone will play the new text

message for you.

After reading a message, you can “Reply” or

“Forward” the message using Uconnect Phone.
Send Messages:
You can send messages using Uconnect Phone.

To send a new message:

1. Push the Phone button .

2. After the “Ready” prompt and the following

beep, say “SMS Send” or “Send Message”.

MULTIMEDIA

317

3. You can either say the message you wish to

send or say “List Messages.” There are 20

preset messages.

To send a message, push the Voice Command

button while the system is listing the

message and say “Send”.
Uconnect Phone will prompt you to say the

name or number of the person you wish to send

the message to.
List of Preset Messages:

1. Yes

2. No

3. Where are you?

4. I need more direction

5. L O L

6. Why

7. I love you

8. Call me

9. Call me later

10. Thanks

11. See You in 15 minutes

12. I am on my way

13. I’ll be late

14. Are you there yet?

15. Where are we meeting?

16. Can this wait?

17. Bye for now

18. When can we meet?

19. Send number to call

20. Start without me

Turn SMS Incoming Announcement ON/OFF
Turning the SMS Incoming Announcement Off

will stop the system from announcing the new

incoming messages.

1. Push the Phone button .

2. After the “Ready” prompt and the following

beep, say “Setup, SMS Incoming Message

Announcement,” you will then be given a

choice to change it.

Bluetooth® Communication Link
Mobile phones have been found to lose

connection to the Uconnect Phone. When this

happens, the connection can generally be

reestablished by switching the phone off/on.

Your mobile phone is recommended to remain

in Bluetooth® On mode.

Navigation — If Equipped

Safety Precautions And Important

Information

WARNING!



ALWAYS drive safely with your hands on the

steering wheel. You have full responsibility

and assume all risks related to the use of

the Uconnect features and applications in

this vehicle. Only use Uconnect when it is

safe to do so. Failure to do so may result in

an accident involving serious injury or

death.



ALWAYS follow the law! Failure to follow

traffic laws may result in serious injury or

death.

318

MULTIMEDIA

Warning
Read this information carefully before starting

to operate the navigation system and follow the

instructions in this manual. Neither the FCA US

LLC nor Garmin® shall be liable for problems or

accidents resulting from failure to observe the

instructions in this manual.
Failure to avoid the following potentially

hazardous situations could result in an accident

or collision resulting in death or serious injury.



Always drive safely. Only use the navigation

features in this vehicle when it is safe to do

so. You accept full responsibility for the use

of the features in this vehicle.



When navigating, carefully compare informa

tion displayed on the navigation system to all

available navigation sources, including road

signs, road closures, road conditions, traffic

congestion, weather conditions, and other

factors that may affect safety while driving.

For safety, always resolve any discrepancies

before continuing navigation, and defer to

posted road signs and road conditions.



The navigation system is designed to provide

route suggestions. It is not a replacement for

driver attentiveness and good judgment. Do

not follow route suggestions if they suggest

an unsafe or illegal maneuver or would place

the vehicle in an unsafe situation.



Be careful of the ambient temperature. Using

the navigation system at extreme tempera

tures can lead to malfunction or damage.

Also note that the unit can be damaged by

strong vibration, metal objects, or by water

getting inside the unit.

Caution
The navigation system is designed to provide

you with route suggestions. It does not reflect

road closures or road conditions, weather

conditions, or other factors that may affect

safety or timing while driving.
Use the navigation system only as a naviga

tional aid. Do not attempt to use the navigation

system for any purpose requiring precise

measurement of direction, distance, location,

or topography.

The Global Positioning System (GPS) is

operated by the United States government,

which is solely responsible for its accuracy and

maintenance. The government system is

subject to changes that could affect the

accuracy and performance of all GPS

equipment, including the navigation system.

Notice
This navigation system can be used when the

ignition key is turned to ON/RUN or ACC. To

preserve the battery, however, it should be used

with the engine running whenever possible.

Using the navigation system for a long time with

the engine switched off can cause the battery to

run down.

Map Data Information
Garmin® uses a combination of governmental

and private data sources. Virtually all data

sources contain some inaccurate or incomplete

data. In some countries, complete and accurate

map information is either not available or is

prohibitively expensive.

MULTIMEDIA

319

Getting Started

To access the Navigation system on your Radio,

press the NAV button in the upper right corner

of the screen during any Radio or Media mode.

Setting Up Your System
When using your navigation system for the first

time, complete the following tasks:

1. Acquire satellites.

2. Understand the main menu.

Acquiring Satellites
The bars indicate satellite strength.
Go to an open area, away from tall buildings and

trees.
Acquiring satellite signals can take a few

minutes.

Main Menu

Using The On-Screen Buttons



Press and hold to quickly return to the

main menu.



Press and to see more choices.



Press and hold and to scroll faster.

Using The On-screen Keyboard



Press a character on the keyboard to enter a

letter or number.



Press “Space” to add a space.



Press to delete a character.



Press and hold to erase the entire entry.



Press to select the keyboard language

mode.



Press to enter special characters, such as

punctuation marks.

Finding A Point Of Interest
The detailed maps loaded in your navigation

system contain points of interest, such as

restaurants, hotels and auto services.

1. From the main menu, press Where To? >

Points of Interest.

2. Select a category.

3. If necessary, select a subcategory.

4. Select a destination.

5. Press Go!

1 — Press To Find A Destination
2 — Press To View The Map
3 — Press To Stop A Route
4 — Press To Detour A Route
5 — Press To Open The Menu Of Tools
6 — Press To Open The Menu Of Settings

320

MULTIMEDIA

Finding A Location By Spelling The Name

1. From the main menu, press Where To? >

Points of Interest > Spell Name.

2. Enter all or part of the name.

3. Press Done.

4. Select a destination.

5. Press Go!

Adding Points To The Active Route

1. While navigating a route, press to return

to the main menu.

2. From the main menu, press Where To?

3. Select a category.

4. If necessary, select a subcategory.

5. Select a destination.

6. Press Go!

7. Press Add as a Via Point.

Changing The Destination Of The Active Route
Before you can change destinations you must

be navigating a route.

1. Press to return to the main menu.

2. Press Where To?

3. Search for the location.

4. Press Go!

5. Press Set as a New Destination.

Taking A Detour
While navigating a route, you can use detours to

avoid obstacles ahead of you, such as

construction zones.

NOTE:

If the route you are currently taking is the only

reasonable option, the navigation system might

not calculate a detour.

1. While navigating a route, press .

2. From the main menu, press Detour.

Stopping The Route

1. While navigating a route, press .

2. From the main menu, press Stop.

Finding Locations

The Where To? menu provides several different

categories you can use to search for locations.

To perform a simple search, see the “Getting

Started” section.

Finding An Address

NOTE:

Depending on the version of the built-in map

data on your navigation system, the button

names, and the order of steps could be

different than the steps below.

1. From the main menu, press Where To? >

Address.

2. If necessary, change the state, the country,

or the province.

3. Press Spell City.

4. Enter the city/postal code.

MULTIMEDIA

321

NOTE:

If you are unsure of the city/postal code, press

Search All.

5. Press Done.

6. If necessary, select the city/postal code.

NOTE:

Not all map data provides postal code

searching.

7. Enter the number of the address.

8. Press Done.

9. Enter the street name.

10. Press Done.

11. If necessary, select the street.

12. If necessary, select the address.

Using The Go! Page
The Go! page opens when you select a location

to navigate to.

1. Press to call the selected location when

your device is connected to phone, or to

save the location to your favorites.

2. Press to switch between 2D and 3D view.

3. Press to rotate the view.

4. Press to view more information for the

location.

5. Press to zoom in and out.

6. Press to return to the previous page. Press

and hold to return to the main menu.

7. Press to create a turn-by-turn route to this

location.

Setting A Home Location
You can set your home location for the location

you return to most often.

1. From the main menu, press Where To? >

Go Home.

2. Select Enter My Address, Use My Current

Location or Recently Found.

Going Home
Before you can navigate to home you must set

a home location.



From the main menu, press Where To? > Go

Home.

Editing Your Home Location Information

1. From the main menu, press Where To? >

Favorites > Home.

2. Press > Edit.

3. Enter your changes.

4. Press Done.

322

MULTIMEDIA

Viewing A List Of Recently Found Locations
Your navigation system stores the last 50

locations you have found.



From the main menu, press Where To? >

Recently Found.

Clearing The List Of Recently Found Locations
From the main menu, press Where To? >
Recently Found > > Clear > Yes.

About Favorites
You can save locations in your Favorites so you

can quickly find them and create routes to

them. Your home location is also stored in

Favorites.

Saving Your Current Location To Favorites

1. From the map, press the vehicle icon.

2. Press Save.

3. Enter a name.

4. Press Done.

The location is saved in Favorites.

Saving Locations To Favorites

1. Search for the location.

2. From the Go! page, press > Save > OK.

Finding Favorites

1. From the main menu, press Where To? >

Favorites.

2. If necessary, select a category.

3. Select a saved location.

Editing Favorites

1. From the main menu, press Where To? >

Favorites.

2. Select a category.

3. Select a favorite.

4. Press the information box.

5. Press > Edit.

6. Select an option:



Name



Phone Number



Categories



Change Map Symbol

7. Edit the information.

8. Press Done.

Planning A Trip
You can use Trip Planner to create and save a

trip with multiple destinations.

1. From the main menu, press Where To? >

Trip Planner.

2. Press .

3. Press Select Start Location.

4. Search for a location.

5. Press Select.

6. Press to add an additional location.

7. Press Select.

MULTIMEDIA

323

8. Repeat steps four to six to add additional

locations to your trip.

9. Press Next.

10. Enter a name.

11. Press Done.

Editing A Saved Trip

1. From the main menu, press Where To? >

Trip Planner.

2. Select a saved trip.

3. Press

4. Select an option:



Press Rename Trip to edit the trip name.



Press Edit Destinations to add or delete

locations.



Press Delete Trip to delete the entire trip.



Press Optimize Order to arrange your trip

locations in the most efficient order.

Navigating To A Saved Trip

1. From the main menu, press Where To? >

Trip Planner.

2. Select a saved trip.

3. Press Go!

Using The Map Buttons

1. From the main menu, press Where To? >

Browse Map.

2. Press anywhere on the map.



Press and to zoom in and out.



Press to switch between 2D and 3D

views.



Press to rotate the view.

Browsing The Map By Pressing The Touch

screen



Press an area on the map to select a location.
An information box appears next to the loca

tion.



Press and drag the map to view different

parts of the map.



Press the map twice to zoom in and center on

a location.

Finding A Location Using The Map

1. From the main menu, press Where To? >

Browse Map.

2. Press a location.

An information box appears next to the loca

tion.

3. Press the information box.

4. Select an option:



Press > Save.

5. Press Go!

324

MULTIMEDIA

Setting A Simulated Location
You can use the GPS simulator to select another

location, near which you can search for and

save points of interest. This may be helpful

when planning trips.

1. From the main menu, press Tools >

Settings > System > GPS Simulator > On.

2. From the main menu, press Where To? >

Browse Map.

3. Press an area on the map.

4. Press > Set Location.

Entering Coordinates
If you know the geographic coordinates of your

destination, you can use your navigation system

to navigate to the destination using the latitude

and longitude coordinates.

1. From the main menu, press Where To? >

Coordinates.

2. Press a field to enter the latitude and

longitude data.

3. Press View on Map.

4. Press Go!

Changing The Map Coordinate Format

1. From the Home Screen, press Where To? >

Coordinates > > Format.

2. Select a format.

About Map Pages

Viewing The Map While Navigating

NOTICE
In no event shall Garmin be liable for any

incidental, special, indirect, or consequential

damages, including, without limitation,

damages for any traffic fines or citations,

whether resulting from the use, misuse, or

inability to use the product or from defects in

the product. Some states do not allow the

exclusion of incidental or consequential

damages, so the above limitations may not

apply to you.
Your route is marked with a magenta line. A

checkered flag marks your destination.

As you travel, your navigation system guides you

to your destination with voice prompts, arrows

on the map, and directions at the top of the

map. If you depart from the original route, your

navigation system recalculates the route and

provides new directions.
A speed limit icon displaying the current speed

limit may appear as you travel on major

roadways.

Using The Navigation Map

1. Press to view the next turn.

The turn indicator also tells you which lane

you should be in to prepare for your next

maneuver, when available.

2. Press to view the turn list.

3. Press to zoom in and zoom out.

MULTIMEDIA

325

4. Press to view trip information.

5. Press to view information for the location.

6. Press to display a different data field.

7. Press to return to the main menu.

About myTrends
When the myTrends feature is enabled, your

estimated time of arrival for your frequent

destinations, like your workplace, automatically

appear in the navigation bar at the top of the

map.
When myTrends information appears in the

navigation bar, you can press the navigation bar

to view route options for the suggested

destination.

Enabling myTrends
From the main menu press Settings >

Navigation > myTrends > Enabled.

Viewing Trip Information
The trip information page displays your present

speed and provides statistics about your trip.

NOTE:

If you make frequent stops, leave the navigation

system turned on so it can accurately measure

elapsed time during the trip.

From the map, press the Speed field.

Resetting Trip Information

1. From the map, press the Speed field.

2. Press .

3. Select an option:



Press Reset Trip Mileage to reset the

information on the trip computer.



Press Reset Max. Speed to reset the

maximum speed.

Viewing The Turn List
When you are navigating a route, you can view

all of the turns for your entire route and the

distance between turns.

1. From the map, press the text bar on the top

of the map.

2. Select an option:



Select a turn on the list to view the next

turn.



Press > Map to view the entire route

on the map.

326

MULTIMEDIA

Viewing The Next Turn
Before you can view the next turn you must be

navigating a route.
The next turn shows the turn on the map and

the distance and time left before you reach the

turn.
Press the turn indicator in the top left corner of

the map.

Viewing The Junction View
Before you can view the junction view, you must

be navigating a route.
The junction view displays a view of some

upcoming junctions and in which lane you

should be driving.

Using The Tools

Viewing Current Location Information
Use the Where Am I? page to view information

about your current location. This feature is

helpful if you need to tell emergency personnel

your location.



From the main menu, press Tools > Where

Am I?

Finding Nearby Services

1. From the main menu, press Tools > Where

Am I?

2. Press Hospitals, Police Stations or Fuel to

view the nearest locations in that category.

Using Help
From the main menu, press Tools > Help to view

information about using your navigation

system.

Searching Help Topics
From the main menu, press Tools > Help.

Using The World Clock

1. From the main menu, press Tools > World

Clock.

2. Press a city name.

3. Enter a new city name.

4. Press Done.

5. If necessary, select a city.

Viewing The World Map



From the main menu press Tools > World
Clock > .



Nighttime hours appear in the shaded area.

Dodge Grand Caravan (2020 year). Manual in english - page 20