Citroën C5 Aircross (2022 year). Manual in english - page 11

162

Practical information

To recharge the battery, avoid repeatedly or 

continuously restarting the engine.

A flat battery prevents the engine from 

starting.

For more information on the 

12 V battery

, 

refer to the corresponding section.

Load reduction mode

This system manages the use of certain 

functions according to the level of charge 

remaining in the battery.

When the vehicle is being driven, the load 

reduction function temporarily deactivates certain 

functions, such as the air conditioning and the 

heated rear screen.

The deactivated functions are reactivated 

automatically as soon as conditions permit.

Snow chains

In wintry conditions, snow chains improve 

traction as well as the behaviour of the vehicle 

when braking.

Snow chains must be fitted only to the 

front wheels. They must never be fitted to 

"space-saver" type spare wheels.

Observe the legislation in force in your 

country relating to the use of snow 

chains and maximum authorised speeds.

Use only chains designed to be fitted to the type 

of wheel fitted to the vehicle:

Original tyre size

Maximum link size

215/65 R17

9 mm

225/55 R18

9 mm

235/55 R18

Cannot be fitted with 

chains

205/55 R19

9 mm

225/50 R19

Cannot be fitted with 

chains

For more information on snow chains, contact a 

CITROËN dealer or a qualified workshop.

Installation tips 

►  To fit the snow 

chains during a journey, stop 

the vehicle on a flat surface at the side of the 

road.

►  Apply the parking brake and position any 

wheel chocks under the wheels to prevent 

movement of the vehicle.

►  Fit the snow chains following the instructions 

provided by the manufacturer.

►  Move off gently and drive for a few moments, 

without exceeding 31 mph (50 km/h).

►  Stop the vehicle and check that the snow 

chains are correctly tightened.

It is strongly recommended that you 

practise fitting the snow chains on a level 

and dry surface before setting off.

Avoid driving with snow chains on roads 

that have been cleared of snow to avoid 

damaging the vehicle's tyres and the road 

surface. If the vehicle is fitted with alloy 

wheels, check that no part of the chain or its 

fixings is in contact with the wheel rim.

Very cold climate screen

(Depending on country of sale)

This removable device prevents the 

accumulation of snow around the radiator 

cooling fan.

In case of difficulty with installation/

removal

Contact a CITROËN dealer or a qualified 

workshop.

Before any operation, ensure that the 

engine is off and the cooling fan has 

stopped.

It is essential to remove it when:

–  the outside temperature exceeds 

10°C.

–  recovery is in progress.

–  the speed is above 75 mph (120 km/h).

163

Practical information

7

Fitting

 

 

►  Place the screen against the bumper grille.

►  Clip the screen.

►  Check that the screen is firmly held by 

pressing around the edges.

Removing

 

 

►  Unclip the screen with your fingers or a tool.

Roof bars

As a safety measure and to avoid 

damaging the roof, it is essential to use 

transverse roof bars approved for your 

vehicle.

Observe the instructions on fitting and use 

contained in the guide supplied with the roof 

bars.

Maximum load distributed over the 

transverse roof bars, for a loading height 

not exceeding 40 cm (except bicycle carrier): 

75 kg

.

As this value may change, please verify the 

maximum load quoted in the guide supplied 

with the roof bars.

If the height exceeds 40 cm, adapt the speed 

of the vehicle to the profile of the road to 

avoid damaging the roof bars and the fixings 

on the vehicle.

Be sure to refer to national legislation in order 

to comply with the regulations for transporting 

objects that are longer than the vehicle.

 

 

Sunroof

Do not operate the sunroof when using 

roof bars - risk of major damage!

Recommendations

Distribute the load uniformly, taking care 

to avoid overloading one of the sides.

Arrange the heaviest part of the load as close 

as possible to the roof.

Secure the load firmly.

Drive gently: the vehicle will be more 

susceptible to the effects of side winds and its 

stability may be affected.

Regularly check the security and tight 

fastening of the roof bars, at least before each 

trip.

Remove the roof bars once they are no longer 

needed.

Direct fitting on roof

 

 

The transverse bars must only be fixed at the 

four anchorage points located on the roof frame. 

These points are concealed by the vehicle doors 

when the doors are closed.

164

Practical information

The roof bar fixings have a stud which must be 

inserted into the opening of each anchorage 

point.

Fitting on longitudinal bars

 

 

The transverse bars must be fixed at the 

markings located on the longitudinal bars.

Bonnet

Stop & Start

Before doing anything under the bonnet, 

you must switch off the ignition to avoid any 

risk of the engine restarting automatically.

Take care with objects or clothing that could 

be caught in the blades of the cooling fan 

or in certain moving components - risk of 

strangulation and serious injury!

Rechargeable hybrid vehicles

Before any work is carried out under the 

bonnet, it is essential to switch off the ignition 

and disconnect the charging connector nozzle 

if it is connected, check that the 

READY

 

indicator lamp is off on the instrument panel 

and wait 4 minutes - risk of serious injury!

The location of the interior bonnet 

release lever prevents opening the 

bonnet when the left-hand front door is 

closed.

When the engine is hot, handle the 

exterior safety catch and the bonnet stay 

with care (risk of burns), using the protected 

area.

When the bonnet is open, take care not to 

damage the safety catch.

Do not open the bonnet under very windy 

conditions.

Cooling of the engine when stopped

The engine cooling fan may start after 

the engine has been switched off.

Take care with objects or clothing that 

could be caught in the blades of the fan!

Opening

 

 

 

 

►  Open the left-

hand front door.

►  Pull the interior release lever, located at the 

bottom of the door frame, towards you.

 

 

►  Lift the exterior safety catch and raise the 

bonnet.

►  Unclip the stay from its housing and place it 

in the support slot to hold the bonnet open.

165

Practical information

7

Closing

►  Hold the bonnet and pull out the stay from the 

support slot.

►  Clip the stay in its housing.

►  Lower the bonnet and release it near the end 

of its travel.

►  Pull on the bonnet to check that it is locked 

correctly.

Because of the presence of electrical 

equipment under the bonnet, it is strongly 

recommended that exposure to water (rain, 

washing, etc.) be limited. 

Engine compartment

The engine shown here is an example for 

illustrative purposes only.

The locations of the following elements may 

vary:

–  Air filter.

–  Engine oil dipstick.

–  Engine oil filler cap.

Petrol engine

 

 

Diesel engine

 

 

1.

Screenwash fluid reservoir

2.

Engine coolant reservoir

3.

Brake fluid reservoir

4.

Battery/Fuses

5.

Remote earth point (-)

6.

Fusebox

7.

Air filter

8.

Engine oil filler cap

9.

Engine oil dipstick

The Diesel fuel system operates under 

very high pressure.

All work on this circuit must be carried out 

only by a CITROËN dealer or a qualified 

workshop.

Checking levels

Check all of the following levels regularly in 

accordance with the manufacturer's service 

schedule. Top them up if required, unless 

otherwise indicated.

If a level drops significantly, have the 

corresponding system checked by a CITROËN 

dealer or a qualified workshop.

The fluids must comply with the 

manufacturer's requirements and with 

the vehicle's engine.

Take care when working under the 

bonnet, as certain areas of the engine 

may be extremely hot (risk of burns) and the 

cooling fan could start at any time (even with 

the ignition off).

Used products

Avoid prolonged contact of used oil or 

fluids with the skin.

Most of these fluids are harmful to health and 

very corrosive.

Do not discard used oil or fluids into 

sewers or onto the ground.

Empty used oil into the containers reserved 

for this purpose at a CITROËN dealer or a 

qualified workshop.

Engine oil

The level is checked, with the engine 

having been switched off for at least 30 

minutes and on level ground, either using the oil 

level indicator in the instrument panel when the 

166

Practical information

ignition is switched on (for vehicles equipped 

with an electric gauge), or using the dipstick.

It is normal to top up the oil level between two 

services (or oil changes). It is recommended 

that you check the level, and top up if necessary, 

every 3,000 miles (5,000 km).

In order to maintain the reliability of the 

engine and emissions control system, 

never use additives in the engine oil.

Checking using the dipstick

For the location of the dipstick, please refer 

to the illustration of the corresponding engine 

compartment.

►  Grasp the dipstick by its coloured grip and 

pull it out completely.

►  Wipe the end of the dipstick using a clean, 

lint-free cloth.

 

 

►  Reinsert the dipstick and push fully down, 

then pull it out again to visually check the oil 

level: the correct level is between marks 

A (max)

 

and 

B (min).

Do not start the engine if the level is:

–  above mark 

A

: contact a CITROËN dealer or a 

qualified workshop.

–  below mark 

B

: top up the engine oil 

immediately.

Oil grade

Before topping up or changing the 

engine oil, check that the oil is suitable 

for your engine and complies with the 

recommendations in the service schedule 

supplied with the vehicle (or available from 

your CITROËN dealer or qualified workshop).

Use of non-recommended oil may invalidate 

your warranty in the event of engine failure.

Topping up the engine oil level

For the location of the engine oil filler cap, please 

refer to the corresponding engine compartment 

illustration.

►  Add oil in small quantities, avoiding any spills 

on engine components (risk of fire).

►  Wait a few minutes before checking the level 

again using the dipstick.

►  Top up the level if necessary.

►  After checking the level, carefully screw the 

oil filler cap back on and replace the dipstick in 

its tube.

The oil level indication displayed on the 

instrument panel when the ignition is 

switched on is not valid for 30 minutes 

following an addition of oil. 

Brake fluid

The level of this fluid should be 

close to 

the "

MAX

" mark. If not, check the brake 

pads for wear.

To know how often the brake fluid should be 

replaced, refer to the manufacturer's servicing 

schedule.

Clean the cap before removing it to refill. 

Use only DOT4 brake fluid from a sealed 

container.

Engine coolant

It is normal to top up this 

fluid between 

two services.

The check and top-up must only be done with 

the engine cold.

A level of coolant that is too low risks causing 

major damage to the engine; the coolant level 

must be close to the "

MAX

" mark without ever 

going above it.

If the level is close to or below the "

MIN

" mark, it 

is essential to top it up.

When the engine is hot, the temperature of the 

coolant is regulated by the fan.

As the cooling system is pressurised, wait at 

least one hour after switching off the engine 

before carrying out any work.

In order to avoid the risk of scalding if you need 

to top up in an emergency, wrap a cloth around 

the cap and unscrew the cap by two turns to 

allow the pressure to drop.

167

Practical information

7

Once the pressure has dropped, remove the cap 

and top up to the required level.

Cooling of the engine when stopped

The engine cooling fan may start after 

the engine has been switched off.

Take care with objects or clothing that 

could be caught in the blades of the fan!

Screenwash fluid

Top up to the required level when 

necessary.

Fluid specification

The fluid must be topped up with a pre-mixed 

product.

In winter (temperatures below zero), a fluid 

containing an anti-freeze agent which is 

appropriate for the temperature conditions 

must be used in order to protect the system's 

components (pump, tank, ducts, jets).

Filling with pure water is prohibited in all 

circumstances (risk of freezing, 

limescale, etc.).

Diesel fuel additive (Diesel 

with particle filter)

On reaching the minimum level in 

the particle filter additive tank, one 

of these warning lamps comes on fixed, 

accompanied by an audible signal and a warning 

message.

Topping up

The topping up of this additive must be carried 

out quickly.

Visit a CITROËN dealer or a qualified workshop.

AdBlue

®

 (BlueHDi)

An alert is triggered when the reserve level is 

reached.

For more information on the 

Indicators

 and in 

particular the AdBlue range indicators, refer to 

the corresponding section.

To avoid the vehicle being immobilised in 

accordance with regulations, you must top up the 

AdBlue tank.

For more information on 

AdBlue

®

 (BlueHDi)

, 

and in particular the supply of AdBlue, refer to 

the corresponding section.

Checks

Unless otherwise indicated, check these 

components in accordance with the 

manufacturer's service schedule and according 

to your engine.

Otherwise, have them checked by a CITROËN 

dealer or a qualified workshop.

Only use products recommended by 

CITROËN or products of equivalent 

quality and specification.

In order to optimise the operation of 

components as important as those in the 

braking system, CITROËN selects and offers 

very specific products.

12 V battery

The battery does not require any 

maintenance.

Check regularly that the terminals are correctly 

tightened (versions without quick-release 

terminals) and that the connections are clean.

For more information on the precautions 

to take before any work on the 

12 V 

battery

, refer to the corresponding section.

Versions equipped with Stop & Start are 

fitted 

with a 12 V lead-acid battery with 

special technology and specifications.

Its replacement should be carried out only by 

a CITROËN dealer or a qualified workshop.

Passenger compartment 

filter

Depending on the environment and the 

use of the vehicle (e.g. dusty atmosphere, 

city driving), 

change it twice as often, if 

necessary

.

168

Practical information

A clogged passenger compartment filter 

can adversely affect air conditioning 

system performance and generate 

undesirable odours.

Air filter

Depending on the environment and the 

use of the vehicle (e.g. dusty atmosphere, 

city driving), 

change it twice as often, if 

necessary

.

Oil filter

Change the oil filter each time the 

engine 

oil is changed.

Particle filter (Diesel)

/

The start of clogging of the 

particle filter is indicated by the 

temporary lighting of this warning lamp, 

accompanied by an alert message.

As soon as traffic conditions allow, regenerate 

the filter by driving at a speed of at least 37 mph 

(60 km/h), with an engine speed above 2,500 

rpm, for about 15 minutes (until the warning lamp 

goes out).

If it is not possible to reach 37 mph (60 km/h), 

leave the engine running at idle for about 15 

minutes, then drive with an engine speed above 

2,500 rpm for 15 minutes.

Do not switch off the engine until the filter 

is fully regenerated; repeated intervals 

can degrade the engine oil prematurely.

Regenerating the filter while the vehicle is 

stationary is not recommended.

If the warning lamp stays on, this 

indicates a low Diesel additive level.

For more information on 

Checking levels

, 

refer to the corresponding section.

Following prolonged operation of the 

vehicle at very low speed or at idle, you 

may, in exceptional circumstances, notice 

water vapour coming from the exhaust while 

accelerating. These emissions have no 

impact on the vehicle’s behaviour and the 

environment.

New vehicle

During the first few particle filter 

regeneration operations, you may notice a 

"burning" smell. This is perfectly normal.

Manual gearbox

The gearbox does not require any 

maintenance (no oil change).

Automatic gearbox

The gearbox does not require any 

maintenance (no oil change).

Brake pads

Brake wear depends on the style of 

driving, particularly in the case of vehicles 

used in town, over short distances. It may be 

necessary to have the condition of the brakes 

checked, even between vehicle services.

Unless there is a leak in the circuit, a drop in the 

brake fluid level indicates that the brake pads 

are worn.

After washing the vehicle, moisture, or in 

wintry conditions, ice can form on the 

brake discs and pads: braking efficiency may 

be reduced. Gently dab the brakes to dry and 

defrost them.

Brake disc wear

For information on checking brake disc 

wear, contact a CITROËN dealer or a 

qualified workshop.

Electric parking brake

This system does not require any routine 

servicing. However, in the event of a 

problem, do not hesitate to have the system 

checked by a CITROËN dealer or a qualified 

workshop.

For more information on the 

Electric 

parking brake

, refer to the 

corresponding section.

169

Practical information

7

Wheels and tyres

The inflation pressure of all 

tyres, 

including the spare wheel, must be 

checked on "cold” tyres.

The pressures indicated on the tyre pressure 

label are valid for "cold" tyres. If you have driven 

for more than 10 minutes or more than 6 miles 

(10 kilometres) at over 31 mph (50 km/h), add 

0.3 bar (30 kPa) to the values indicated on the 

label.

Under-inflation increases energy 

consumption. Non-compliant tyre 

pressures cause tyres to wear prematurely 

and have an adverse effect on the vehicle's 

road holding - risk of accident!

Driving with worn or damaged tyres reduces the 

braking and road holding performance of the 

vehicle. Regularly check the condition of the 

tyres (tread and sidewalls) and rims as well as 

the presence of the valve caps.

When the wear indicators no longer appear set 

back from the tread, the depth of the grooves is 

less than 1.6 mm; replace the tyres as soon as 

possible.

Using different size wheels and tyres from those 

specified can affect the lifetime of tyres, wheel 

rotation, ground clearance, the speedometer 

reading and have an adverse effect on road 

holding.

Fitting different tyres on the front and rear axles 

can cause the ESC to mistime.

Always mark the direction of rotation on the tyres 

that will be stored when fitting winter or summer 

tyres. Store them in a cool, dry place and away 

from direct exposure to the sun's rays.

Winter or 4-seasons tyres can be 

identified by this symbol on their 

sidewalls.

Shock absorbers

It is not easy for drivers to detect when 

shock absorbers are worn. Nevertheless, 

the shock absorbers have a major impact on 

road holding and braking performance.

For your safety and driving comfort, it is 

important to have them regularly checked by a 

CITROËN dealer or a qualified workshop.

Timing and accessory kits

The timing and accessory kits are used 

from the time the engine is started until it 

is switched off. It is normal for them to wear over 

time.

A faulty timing or accessory kit can damage 

the engine, rendering it unusable. Observe the 

recommended replacement frequency, stated in 

distance travelled or time elapsed, whichever is 

reached first.

AdBlue

®

 (BlueHDi)

To respect the environment and ensure 

compliance with the Euro 6 standard, without 

adversely affecting the performance or fuel 

consumption of its Diesel engines, CITROËN 

has taken the decision to equip its vehicles with 

a system that combines SCR (Selective Catalytic 

Reduction) with a Diesel Particle Filter (DPF) for 

the treatment of exhaust gases.

SCR system

Using a liquid called AdBlue

®

 that contains 

urea, a catalytic converter turns up to 85% of 

the nitrogen oxides (NOx) into nitrogen and 

water, which are harmless to health and the 

environment.

The AdBlue

®

 is contained in 

a special 

tank

 holding about 17 litres. 

Its capacity allows a driving range of 

approximately 4,000 miles (6,500 km), 

which 

may vary considerably

 depending on your 

driving style.

An alert system is triggered once the reserve 

level is reached: it is then possible to drive for a 

further 1,500 miles (2,400 km) before the tank is 

empty and the vehicle is immobilised.

For more information on the 

Warning 

and indicator lamps

 and the associated 

alerts, or the 

Indicators

, please refer to the 

corresponding sections.

Once the AdBlue

®

 tank is empty, a device 

required by law prevents the engine from 

being restarted.

If the SCR system is faulty, the level of 

emissions from the vehicle will no longer meet 

170

Practical information

the Euro 6 standard and the vehicle starts 

polluting the environment.

In the event of a confirmed SCR system 

malfunction, it is essential to visit a CITROËN 

dealer or a qualified workshop. After 685 

miles (1,100 km), a device is automatically 

activated to prevent the engine from starting.

In both cases, a range indicator indicates 

the distance that can be travelled before the 

vehicle is stopped.

Freezing of the AdBlue

®

AdBlue

®

 freezes at temperatures below 

around -11°C.

The SCR system includes a heater for the 

AdBlue

®

 tank, allowing you to continue driving 

in very cold conditions.

Supply of AdBlue

®

It is recommended that the AdBlue

®

 be topped 

up as soon as the first alert is issued indicating 

that the reserve level has been reached.

For the correct operation of the SCR 

system:

–  Use only AdBlue

®

 fluid that meets the ISO 

22241 standard.

–  Never transfer AdBlue

®

 to another container 

as it would lose its purity.

–  Never dilute AdBlue

®

 with water.

You can obtain AdBlue

®

 from a CITROËN dealer 

or a qualified workshop, as well as service 

stations equipped with AdBlue

®

 pumps specially 

designed for passenger vehicles.

Recommendations on storage

AdBlue

®

 freezes at about -11°C and deteriorates 

above +25°C. Containers should be stored in a 

cool area and protected from direct sunlight.

Under these conditions, the fluid can be kept for 

at least a year.

If the fluid has frozen, it can be used once it has 

completely thawed out at room temperature.

Never store AdBlue

®

 containers in your 

vehicle.

Precautions for use

AdBlue

®

 is a urea-based 

solution. This fluid is 

non-flammable, colourless and odourless (when 

kept in a cool place).

In the event of contact with the skin, wash the 

affected area with soap and running water. In the 

event of contact with the eyes, immediately rinse 

the eyes with large amounts of water or with an 

eye wash solution for at least 15 minutes. Seek 

medical attention if you feel a persistent burning 

sensation or irritation.

If swallowed, immediately wash out the mouth 

with clean water and then drink plenty of water.

In certain conditions (high temperature, for 

example), the risk of release of ammonia cannot 

be excluded: do not inhale the fluid. Ammonia 

vapours have an irritant effect on mucous 

membranes (eyes, nose and throat).

Store AdBlue

®

 out of the reach of 

children, in its original container.

Procedure

Before starting the top-up procedure, ensure that 

the vehicle is parked on a flat and level surface.

In wintry conditions, ensure that the temperature 

of the vehicle is above -11°C. Otherwise the 

AdBlue

®

 may be frozen and so cannot be poured 

into the tank. Park the vehicle in a warmer area 

for a few hours to allow the top-up to be carried 

out.

Never pour the AdBlue

®

 into the Diesel 

fuel tank.

If any AdBlue

®

 is splashed, or if there are 

any spillages on the bodywork, rinse 

immediately with cold water or wipe with a 

damp cloth.

If the fluid has crystallised, clean it off using a 

sponge and hot water.

Important: 

in the event of a top-up after 

a breakdown because of a lack of 

AdBlue,

 it is essential to wait around 5 

minutes before switching on the ignition, 

without opening the driver’s door, 

unlocking the vehicle, inserting the key 

into the ignition switch, or bringing the 

171

Practical information

7

key for the "Keyless Entry and Start" 

system into the passenger compartment

.

Switch on the ignition, then wait for 10 

seconds before starting the engine.

►  Switch off the ignition and remove the key 

from the switch to switch off the engine.

or

►  With Keyless Entry and Start, press the 

"

START/STOP

" button to switch off the engine.

 

 

►  Turn the blue cap of the AdBlue

®

 tank anti-

clockwise and remove it.

►  With a container of AdBlue

®

: after checking 

the expiry date, read the instructions on the 

label carefully before pouring the contents of the 

container into the vehicle's AdBlue

®

 tank.

►  With an AdBlue

®

 pump: insert the nozzle and 

fill the tank until the nozzle automatically cuts 

out.

In order not to overfill the AdBlue

®

 tank:

–  Add between 10 and 13 litres using 

AdBlue

®

 containers.

–  Stop after the nozzle’s first automatic cut-

out, if you are refilling at a service station.

The system only registers AdBlue

®

 

intermediate top-ups of 5 litres or more.

If the AdBlue

®

 tank is completely empty 

– which is confirmed by the message 

“

Top up AdBlue: Starting impossible

” – it is 

essential to add at least 10 litres.

Top-up detection may not be instantaneous 

after addition. It may take a few minutes of 

driving before the top-up detection is effective.

Free-wheeling

In certain situations, it is necessary to put the 

vehicle into free-wheeling mode (e.g. towing, on 

a rolling road, automatic car wash (Wash mode), 

rail or sea transport).

The procedure varies according to the type of 

gearbox and parking brake.

Never leave the vehicle unattended with 

the vehicle into free-wheeling mode.

With a manual gearbox and 

electric parking brake

 

/

 

To release them

►  With the engine running and while depressing 

the brake pedal, move the gear selector to the 

neutral position.

►  While depressing the brake pedal, switch off 

the engine.

►  Release the brake pedal, then switch on the 

ignition.

►  While depressing the brake pedal, press the 

control to release the parking brake.

►  Release the brake pedal, then switch off the 

ignition.

Reverting to normal operation

►  While depressing the brake pedal, restart the 

engine and apply the parking brake.

Keyless Entry and Start

You must not depress the brake pedal 

while switching the ignition on again, then 

switching it off. If you do, the engine will start, 

requiring you to restart the procedure.

With an automatic gearbox 

and electric parking brake

 

/

 

Release procedure

►  With the vehicle stationary and the engine 

running, depress the brake pedal and select 

mode 

N

.

Within 5 seconds:

►  Depress and hold the brake pedal, then 

observe this order: switch off the engine and 

move the push selector forwards or backwards.

172

Practical information

►  Release the brake pedal, then switch on the 

ignition.

►  Place your foot on the brake and press the 

electric parking brake control to release it.

►  Release the brake pedal, then switch off the 

ignition.

A message is displayed on the 

instrument panel to confirm the unlocking 

of the wheels for 15 minutes.

When the vehicle is free-wheeling, the 

audio system cannot be updated (message 

displayed on the instrument panel).

After 15 minutes or reverting to normal 

operation

►  While depressing the brake pedal, restart the 

engine and select mode 

P

.

Keyless Entry and Start

You must not depress the brake pedal 

while switching the ignition on again, then 

switching it off. If you do, the engine will start, 

requiring you to restart the procedure.

Advice on care and 

maintenance

General recommendations

Observe the following recommendations to avoid 

damaging the vehicle.

Exterior

Never use a high-pressure jet wash in 

the engine compartment - risk of 

damaging the electrical components!

Do not wash the vehicle in bright sunshine or 

extremely cold conditions.

When washing the vehicle in an 

automatic roller-brush car wash, be sure 

to lock the doors and, depending on version, 

move the electronic key away and deactivate 

the "hands-free" function (Hands-Free 

Tailgate Access).

When using a pressure washer, keep the jet 

nozzle at a minimum distance of 30 cm from 

the vehicle (particularly when cleaning areas 

containing chipped paint, sensors or seals).

Promptly clean up any stains containing 

chemicals liable to damage the vehicle's 

paintwork (including tree resin, bird 

droppings, insect secretions, pollen and tar).

Depending on the environment, clean the 

vehicle frequently to remove salty deposits 

(in coastal areas), soot (in industrial areas) 

and mud/salts (in wet or cold areas). These 

substances can be highly corrosive.

Contact a CITROËN dealer or a qualified 

workshop for advice on removing stubborn 

stains requiring special products (such as tar 

or insect removers).

Preferably, have paint touch-ups performed 

by a CITROËN dealer or a qualified 

workshop.

Interior

When washing the vehicle, never use a 

water hose or high-pressure jet to clean 

the interior.

Liquids carried in cups or other open 

containers can spill, presenting a risk of 

damage to the instruments and controls and 

the controls located on the centre console. Be 

vigilant!

To clean instrument panels, touch screens 

or other displays, wipe gently with a soft, 

dry cloth. Do not use products (e.g. alcohol, 

disinfectant) or soapy water directly on these 

surfaces - risk of damage!

Bodywork

High-gloss paint

Do not use abrasive products, solvents, 

petrol or oil to clean the bodywork.

Never use an abrasive sponge to clean 

stubborn stains - risk of scratching the 

paintwork!

Do not apply polish in strong sunshine, or to 

plastic or rubber parts.

173

Practical information

7

Use a soft cloth and soapy water or a pH 

neutral product.

Gently wipe the bodywork with a clean 

microfibre cloth.

Apply polish with the vehicle clean and dry.

Comply with the instructions for use stated on 

the product.

Decals

(Depending on version)

Do not use a high-pressure washer to 

clean the vehicle - risk of damaging or 

detaching the decals!

Use a high-flow hose (temperature 

between 25°C and 40°C).

Place the jet of water perpendicular to the 

surface to be cleaned.

Rinse the vehicle with demineralised water.

Textile

The dashboard, door panels and seats may 

contain parts made of textile material.

Maintenance

Do not use aggressive cleaning products 

(e.g. alcohol, solvent or ammonia).

Do not use steam-cleaning systems - risk of 

affecting the adhesion of the fabrics!

Remove dust from the textile parts 

regularly with a dry cloth, soft brush or 

vacuum cleaner.

Rub down the textile parts once per year with 

a clean, damp cloth. After leaving overnight to 

dry, brush with a soft-bristled brush.

Stain removal

Do not rub the stain or it may spread or 

you may cause the substance to 

penetrate the surface.

Act quickly by reducing the stain from its 

edges inwards.

Remove as much substance or solids as 

possible using a spoon or spatula, and 

remove as much liquid as possible using 

absorbent paper.

Product/Procedure to use depending 

on the type of stain:

–  Grease, oil and ink: clean with a pH-neutral 

detergent.

–  Vomit: clean with sparkling mineral water.

–  Blood: spread flour over the stain and allow 

to dry; remove with a slightly damp cloth.

–  Mud: allow to dry and then remove with a 

slightly damp cloth.

–  Cake, chocolate, ice cream: clean with 

lukewarm water.

–  Sugary and/or alcoholic drinks: clean with 

lukewarm water, or lemon juice if the stain is 

persistent.

–  Hair gel, coffee, tomato sauce, vinegar: 

clean with lukewarm water and lemon juice.

For solid substances, then use a soft brush or 

vacuum cleaner.

For liquid substances, then use a damp 

microfibre cloth and then dry with another 

cloth.

Leather

Leather is a natural product. Appropriate regular 

care is essential for its durability.

It must be protected and nourished using a 

specific leather product, to keep it supple and 

preserve its original appearance.

Do not clean leather using unsuitable 

cleaning agents such as solvents, 

detergents, petrol or pure alcohol.

When cleaning items partly made from 

leather, take care not to damage the other 

materials with the specific leather product.

Before cleaning greasy stains or liquids, 

quickly mop up any surplus.

Before cleaning, wipe off any residues liable 

to scuff the leather, using a cloth that has 

been dampened with demineralised water 

and thoroughly wrung out.

174

Practical information

Clean leather using a soft cloth moistened 

with soapy water or a pH-neutral product.

Dry with a soft, dry cloth.

175

In the event of a breakdown

8

Warning triangle

This reflective and dismantable device is to be 

installed on the side of the road when a vehicle 

is broken down or damaged.

Before getting out of the vehicle

Turn on the hazard warning lamps, then 

put on the safety vest to assemble and install 

the triangle.

Storage compartment

 

 

There is a compartment in the interior trim of the 

tailgate to store a warning triangle.

►  After opening the tailgate, release the cover 

by turning the screw a quarter turn to the left.

Assembling and placing the 

triangle

 

 

For versions supplied with a triangle as original 

equipment, refer to the illustration above.

For other versions, refer to the assembly 

instructions provided with the triangle.

►  Put the triangle in place behind the vehicle, 

as required by local legislation.

Running out of fuel 

(Diesel)

With Diesel engines, the fuel system must be 

primed if you run out of fuel.

Before starting to prime the system

, it is 

essential to put at least 5 litres of Diesel into the 

fuel tank.

For more information on 

Refuelling

 and 

on 

Misfuel prevention (Diesel)

, refer to 

the corresponding section.

BlueHDi 130 engines

►  Switch on the ignition (without starting the 

engine).

►  Wait around 1 minute and switch off the 

ignition.

►  Operate the starter motor to start the engine.

If the engine does not start at the first attempt, 

do not keep trying, but restart the procedure.

BlueHDi 180 engines

►  Switch on the ignition (without starting the 

engine).

►  Wait around 6 seconds and switch off the 

ignition.

►  Repeat the operation 10 times.

►  Operate the starter motor to start the engine.

If the engine does not start at the first attempt, 

do not keep trying, but restart the procedure.

Tool kit

Set of tools supplied with the vehicle.

Its content depends on your vehicle's equipment:

–  Temporary puncture repair kit.

–  Spare wheel.

176

In the event of a breakdown

Accessing the tools

 

 

The tool kit is stored in the boot, under the floor.

To access it:

Versions with 2-position boot floor:

►  Open the boot.

►  Place the adjustable boot floor in the high 

position.

Versions with articulated boot mat 

(Rechargeable hybrid):

►  Open the boot.

►  Unfold the articulated boot mat by pulling its 

handle until it is fully opened.

With temporary puncture repair kit

 

 

►  Unclip the two fixings to open its cover.

With spare wheel

 

 

►  Unclip the storage box by pulling it upwards.

►  Unclip the two fixings to open its cover.

List of tools

 

 

1.

Chocks to immobilise the vehicle (depending 

on equipment)

2.

Socket for the wheel security bolts (located in 

the glove box) (depending on equipment)

To adapt the wheelbrace to the special 

‘security’ bolts.

3.

Towing eye and tool to open the front and 

rear protective covers

For more information on 

Towing the vehicle

 

and using the removable towing eye, refer to the 

corresponding section.

With temporary puncture repair kit

 

 

177

In the event of a breakdown

8

4.

12 V compressor with cartridge of sealant 

and speed limit sticker

For temporary repair of a tyre and to adjust 

the tyre pressure.

For more information about the 

Temporary 

puncture repair kit

, refer to the corresponding 

section.

With spare wheel

 

 

5.

Wheelbrace

For removing the wheel bolts.

6.

Jack with integrated handle

To raise the vehicle.

7.

Wheel bolt cap removal tool (depending on 

equipment)

For removing the wheel bolt head finishers on 

alloy wheels.

For more information on the 

Spare wheel

, refer 

to the corresponding section.

These tools are specific to the vehicle 

and may vary according to the level of 

equipment.

Do not use them for any other purpose.

The jack must only be used to change a 

wheel with a damaged or punctured tyre.

Do not use any jack other than the one 

supplied with the vehicle.

If the vehicle does not have its original jack, 

contact a CITROËN dealer or a qualified 

workshop to obtain the one that was intended 

by the manufacturer.

The jack meets European standards, as 

defined in the Machinery Directive 2006/42/

CE.

The jack does not require any maintenance.

Temporary puncture 

repair kit

Visit this link to view explanatory videos: 

http://q-r.to/bagGl9

Made up of a compressor and a sealant 

cartridge, it allows you to carry out a 

temporary 

repair

 of the tyre so that you can drive to the 

nearest garage.

It is designed to repair most punctures located 

on the tyre tread.

The vehicle's electric system allows the 

connection of the compressor to the 12 V 

power supply for long enough to repair a tyre 

after a puncture.

For more information on the 

Tool kit

, 

refer to the corresponding section.

Tyre inflation pressures are indicated on 

this label.

For more information on 

Identification 

markings

, particularly this label, refer to the 

corresponding section.

Should the pressure of one or more tyres 

be adjusted, it is necessary to reinitialise 

the under-inflation detection system.

For more information on 

Tyre under-inflation 

detection

, refer to the corresponding section.