Citroën Jumpy-Dispatch (2022 year). Manual in english - page 3

34

Access

If the vehicle is not fitted with an alarm, 

deadlocking is confirmed by fixed 

illumination of the direction indicators for 

about two seconds.

With Keyless Entry and Start on your 

person

To lock the vehicle, the remote control must be in 

recognition zone 

A

.

 

 

►  To lock the vehicle 

fully

, press the markings 

on one of the door handles (front door(s), 

manual sliding side door(s) or left-hand side-

hinged door).

►  To deadlock the vehicle, press the markings 

again 

within five seconds.

With electric sliding side door(s)

►  With the Keyless Entry and Start on your 

person, to lock the vehicle 

fully

, press the 

markings on one of the 

front

 door handles.

►  To deadlock the vehicle, press the markings 

again 

within five seconds.

With tailgate

 

 

►  With the Keyless Entry and Start on your 

person, press the tailgate locking control to lock 

the 

entire

 vehicle.

►  To deadlock the vehicle, press the control 

again 

within five seconds

.

If the vehicle is not fitted with an alarm, 

deadlocking is signalled by fixed lighting 

of the direction indicators for approximately 

two seconds.

Back-up procedures

Lost keys, remote control, 

electronic key

Go to a CITROËN dealer with the vehicle's 

registration certificate, your personal 

identification documents and if possible, the label 

bearing the key code.

The CITROËN dealer will be able to retrieve the 

key code and the transponder code, enabling a 

new key to be ordered.

Complete unlocking/locking 

of the vehicle with the key

Use this procedure in the following situations:

–  Remote control battery discharged.

–  Remote control malfunction.

–  Vehicle battery discharged.

–  Vehicle in an area subject to strong 

electromagnetic interference.

In the first case, change the remote control 

battery.

In the second case, reinitialise the remote 

control.

Refer to the corresponding sections.

►  Insert the key into the door lock.

►  Turn the key towards the front/rear to unlock/

lock the vehicle.

►  Turn the key towards the rear again within 

5 seconds to deadlock the vehicle.

If the vehicle is fitted with an alarm, it will 

not be activated when locking with the 

key.

If the alarm is activated, the siren sounds 

when the door is opened; switch on the 

ignition to stop it.

If the vehicle is unlocked with the key in 

the lock 

after locking it with the remote 

control or the Keyless Entry and Start 

35

Access

2

system

, 

all doors and the boot

 are 

unlocked.

If the vehicle is unlocked with the key in the 

lock 

after locking it with the key

, only the 

doors (front door and sliding side door(s)) are 

unlocked. The side-hinged doors and tailgate 

are not unlocked. Switching on the ignition 

unlocks them.

Central locking not 

functioning

Use these procedures in the following cases:

–  Central locking malfunction.

–  Battery disconnected or discharged.

In the event of a malfunction of the 

central locking system, the battery must 

be disconnected to ensure that the vehicle is 

locked fully.

Front left-hand door

►  Insert the key into the door lock.

►  Turn the key towards the rear of the vehicle 

to lock it, or towards the front to unlock it.

Front passenger door and sliding 

side door

Unlocking

►  Pull the interior door opening handle.

Locking

►  Open the door.

►  For the side door, check that the child lock is 

not on. Refer to the corresponding section.

 

 

Front passenger door

 

 

Sliding side door

►  Remove the black cap on the edge of the 

door, using the key.

►  Insert the key in the aperture without 

forcing it, then without turning it, move the latch 

sideways towards the inside of the door.

►  Remove the key and refit the black cap.

►  Close the doors and check from the outside 

that the vehicle is locked.

Side-hinged doors

Unlocking

►  Use the interior opening handle.

Locking

►  If fitted to your vehicle, check that the electric 

child lock is not on.

►  Open the left-hand side-hinged door.

 

 

►  Insert the key into the latch aperture on the 

edge of the door (without forcing it) and slide the 

assembly upwards.

►  Remove the key.

►  Close the door and check from the outside 

that the vehicle is locked. 

Unlocking the tailgate

 

 

►  From inside the vehicle, insert a small 

screwdriver into hole 

A

 on the lock to unlock the 

tailgate.

►  Move the latch to the left.

If the fault persists after closing again, 

the tailgate will remain locked.

36

Access

Changing the battery

If the battery is flat, this warning lamp 

comes on, accompanied by an audible 

signal and the display of a message.

Battery type: CR2032/3 volts.

 

 

►  Unclip the cover by inserting a small 

screwdriver in the slot and lift the cover.

►  Remove the flat battery from its housing.

►  Put the new battery in place, respecting the 

polarity. Start by inserting it into the contacts 

located in the corner, then clip the cover onto 

the unit.

►  Reinitialise the remote control.

For more information on 

Reinitialising the 

remote control

, refer to the corresponding 

section.

Do not throw remote control batteries 

away, as they contain metals that are 

harmful to the environment. Take them to an 

approved disposal point.

Reinitialising the remote 

control

Following replacement of the battery or in 

the event of a fault, it may be necessary to 

reinitialise the remote control.

Without Keyless Entry and Start

 

 

►  Switch the ignition off.

►  Turn the key to position 

2 (Ignition on)

.

►  Immediately press the closed padlock button 

for a few seconds.

►  Switch off the ignition and remove the key 

from the ignition switch.

The remote control is now fully operational 

again.

 

 

►  Insert the mechanical key (incorporated into 

the remote control) into the lock to open the 

vehicle.

►  Place the electronic key against the back-up 

reader on the steering column and hold it there 

until the ignition is switched on.

► 

With a manual gearbox,

 place the gear lever 

in neutral then fully depress the clutch pedal.

► 

With an automatic gearbox or drive 

selector

, while in mode 

P

, depress the brake 

pedal.

►  Switch on the ignition by pressing the 

"

START/STOP

" button.

If the fault persists after reinitialisation, contact a 

CITROËN dealer or a qualified workshop without 

delay.

37

Access

2

Central locking

 

 

 

 

Manual

►  Press this button to lock/unlock the vehicle 

(doors, tailgate or side-hinged doors) from inside 

the passenger compartment. 

The indicator lamp comes on to confirm the 

central locking of the vehicle.

Central locking does not take place if any 

of the doors are open.

When locking/deadlocking from the 

outside

When the vehicle is locked or deadlocked 

from the outside, the indicator lamp flashes 

and the button is deactivated.

►  After normal locking, pull one of the 

interior door controls to unlock the vehicle.

►  After deadlocking, you must use the 

remote control, the "Keyless Entry and 

Start" system or the built-in key to unlock the 

vehicle.

Driving with the doors locked makes 

access for the emergency services more 

difficult in an emergency.

 

 

When transporting an oversized load 

(tailgate or side-hinged doors open), 

press the button to lock only the cab doors.

 

 

When transporting an oversized load 

(tailgate or side-hinged doors open), 

press the button to lock only the front and rear 

doors (sliding side door).

When locking from inside, the door 

mirrors do not fold.

Central locking from the inside does not 

operate if one of the doors is open (indicated 

by a mechanical noise coming from the 

locks).

When the tailgate or side-hinged doors are 

open, only the other doors are locked (the 

button does not light up).

Automatic (anti-intrusion 

security)

The doors and the tailgate or the side-hinged 

doors can lock automatically while driving (speed 

above 6 mph (10 km/h)).

To deactivate/reactivate this function (activated 

by default):

►  Press the button until an audible signal is 

heard and/or a message appears on the screen.

Locking/unlocking the 

loading area

 

 

 

 

 

 

This button is unavailable if the vehicle 

has been locked or deadlocked from 

outside (using the key, remote control or 

Keyless Entry and Start, depending on 

equipment) or if any of the doors are still 

open.

38

Access

Automatic

The 

loading area

 is always locked when driving.

To deactivate this automatic locking, go 

to a CITROËN dealer or a qualified 

workshop.

Manual

►  With complete unlocking activated, 

press this button to lock (indicator lamp 

comes on)/unlock (indicator lamp goes off) the 

vehicle

.

►  With selective unlocking activated, press this 

button to lock (indicator lamp comes on)/unlock 

(indicator lamp goes off) the 

loading area

.

Driving with the doors locked could make 

it more difficult for the emergency 

services to enter the vehicle in an emergency.

The indicator lamp goes off when 

unlocking one or more doors of the 

loading area

.

With the ignition off and the vehicle fully 

locked, the indicator lamp goes off for energy 

economy reasons.

Electric sliding side 

door(s)

The exterior and interior door handles and the 

interior buttons allow the electrically powered 

movement of the door to be started.

Opening and closing of the doors is 

accompanied by an audible signal.

Opening

With the exterior or interior handle

 

 

►  With the door unlocked, pull and release the 

handle to start opening the door. Pull the handle 

again to reverse the direction of the door's 

movement.

With the remote control

 

 

►  With the door unlocked, press and 

hold this button until the corresponding 

sliding side door has opened. 

►  Press this button again to reverse the 

direction of the door's movement.

The remote control buttons are not active 

with the ignition switched on.

With the button(s) on the door pillar

 

 

 

 

With the button(s) at the front

 

 

 

 

►  With total unlocking activated and the child 

lock deactivated, to unlock the vehicle and start 

39

Access

2

opening a door, press the button corresponding 

to the door you wish to open.

►  With selective unlocking activated, to unlock 

only the 

loading area

 and start opening a door, 

press the button corresponding to the door you 

wish to open.

►  In both cases, pressing the button again 

reverses the direction of the door's movement.

Closing

With the exterior handle

 

 

►  Pull and release the handle to start closing 

the door. Pull the handle again to reverse the 

direction of the door's movement.

With the remote control

►  Press and hold this button until the 

sliding side door has closed. Pull the 

handle again to reverse the direction of the 

door's movement.

The remote control buttons are not active 

with the ignition switched on.

With the button(s) on the door pillar

 

 

 

 

With the button(s) at the front

 

 

 

 

►  To start closing a door, press the 

corresponding button for that door. Press again 

to reverse the direction of the door's movement.

The button is not operational and 

pressing it results in an audible signal, if 

the speed of the vehicle is above 20 mph (30 

km/h).

The button(s) at the front or on the door 

pillar is not operational and pressing it 

results in an audible signal, if:

–  the vehicle is moving,

–  the child lock is on (activated) (for the 

buttons on the door pillars),

–  the vehicle has been locked or deadlocked 

from outside (using the key, remote control 

or Keyless Entry and Starting, depending on 

equipment).

The button for the left-hand door is not 

operational and pressing it results in an 

audible signal if the fuel filler flap is open.

General 

recommendations for the 

sliding side doors

Doors must only be operated when the 

vehicle is stationary.

For your safety and that of your passengers, 

as well as for correct operation of the doors, 

you are strongly advised not to drive with a 

door open.

Always check that it is safe to operate the 

door and in particular, be sure not to leave 

children or animals near the door controls 

without supervision.

The audible warning, the lighting of the "door 

open" warning lamp and the message on the 

screen are there to remind you. Contact a 

40

Access

CITROËN dealer or a qualified workshop if 

you want to deactivate this warning.

Lock the vehicle when you use an automatic 

car wash.

Before opening or closing and while 

moving doors, ensure that no person, 

animal or object is in the door frame or any 

other position that would block the desired 

movement, inside or outside the vehicle.

If this advice is not followed, injuries or 

damage may occur if any part of a person or 

an object is trapped or caught.

Electrical door opening is disabled at speeds 

above 2 mph (3 km/h):

–  However, if the vehicle started moving 

while the doors were open, the speed must 

be reduced below 19 mph (30 km/h) before 

they can be closed.

–  Any attempt to open a door electrically 

using the interior handle while driving results 

in it only being possible to open the door 

manually.

–  This situation is accompanied by the 

audible warning, the lighting of the "door 

open" warning lamp and the message on the 

screen. To release the door and be able to 

operate it again, it is necessary to stop the 

vehicle.

Take care not to block the guide space 

on the floor so that the door can slide 

correctly.

For safety and functional reasons, do not 

drive with the sliding side door open.

The electric controls are disabled in the 

event of an impact. Manual opening and 

closing remain possible.

While starting the engine, door 

movements are paused, resuming when 

the engine is running.

Depending on the engine fitted, if 

the door is closed and an opening 

request is issued in Stop mode of Stop & 

Start, the door will open slightly and then 

stop. In Start mode, the door will resume its 

movement when the engine re-starts.

To hold the sliding side door in the open 

position, open the door fully to engage 

the latch (located at the bottom of the door).

Doors and door clearances

 

 

When open, a door projects beyond the body. 

Allow adequate clearance when parking 

alongside walls, lamp-posts, high pavements, 

etc.

 

 

When open, a door never projects 

beyond the rear bumper.

41

Access

2

Safety/Obstacle detection 

with electric door(s)

 

 

The obstacle detection system is triggered when 

the moving door encounters an obstacle with a 

certain level of physical resistance. If an obstacle 

is detected:

–  while the door is closing, the door stops then 

opens fully.

–  while the door is opening, the door stops then 

closes.

–  twice in succession during a movement of the 

door, the door will no longer close electrically 

(uninitialisation).

On a steep slope: a safety system slows down 

the movement of the door.

In all cases, wait a few seconds before operating 

the door (closing or opening).

Close the door manually for safety reasons.

Then reinitialise the door.

Reinitialising electric doors

If electrical operations no longer work:

►  Fully close the door(s) 

manually

.

►  Fully open the door(s) 

electrically

.

►  Close the door(s) 

electrically

.

On completion of this procedure, electric 

operation of the doors is restored.

However, if a problem persists following this 

procedure, contact a CITROËN dealer or a 

qualified workshop.

On a steep slope

 

 

It is possible to open and close the doors 

electrically on slopes of up to a 20% gradient.

If the vehicle is on a slope, with the front of the 

vehicle facing up the slope, open the door with 

care. The door may open more quickly due to 

the incline.

On a steep slope, guide the side door manually 

to help it to close.

 

 

If your vehicle is on a slope, with the front of the 

vehicle facing down the slope, the door may not 

stay open and may close 

violently

 with the risk 

of injury.

In the case of a steep slope, the door 

may be driven by its own weight and as a 

consequence may open or close 

violently

.

There would not be time for action at the 

electric controls to take effect.

There would not be time for the obstacle 

detection system to react.

Take care not to leave the vehicle on a 

steep slope with the door(s) open without 

supervision. If this advice is not followed, 

injuries or damage may occur if a person or 

an object is trapped or caught.

42

Access

Hands-free sliding side 

door(s)

Opening/Closing

 

 

With a movement of your foot while keeping the 

remote control on your person in the recognition 

zone 

A

, the system unlocks and opens the 

sliding side door or closes and locks it.

The remote control must be located at the rear 

of the vehicle, at least about 30 cm but no more 

than about 2 m from the vehicle.

The automatic locking after closing the 

door can be programmed in the vehicle 

configuration menu.

Before making the movement with your 

foot, ensure that you are steady and well 

positioned, so that you do not lose your 

balance (rain, snow, ice, mud, etc.).

Take care not to touch the exhaust tailpipe 

when making the movement with your foot - 

risk of burns.

 

 

►  Put your foot beneath the corner of the rear 

bumper, then move the foot at normal speed with 

a sweeping side movement.

The sensor detects the foot approaching and 

leaving and triggers the opening or closing of the 

side door.

Make the movement without interruption 

and do not repeat it immediately 

afterwards or several times.

If the door does not open, wait about 

2 seconds before trying again.

Do not keep the foot in the air.

Confirmation that the door is going to 

open or close is signalled by the direction 

indicators flashing for a few seconds, 

accompanied by an audible signal.

The movement of the door is reversed if the 

movement of the foot takes place during the 

manoeuvre.

If the vehicle is so equipped, the electric door 

mirrors fold/unfold on locking/unlocking the 

vehicle.

Automatic locking

The vehicle locks itself following the hands-free 

closing of the sliding door.

If your vehicle is not fitted with an alarm, 

locking is signalled by the fixed 

illumination of the direction indicators for 

about two seconds.

Depending on your version, the door mirrors 

fold at the same time.

Activation/Deactivation

With audio system or touch screen

By default, hands-free access is activated.

The "Hands-Free Tailgate Access" 

function or automatic vehicle 

locking when the sliding door is closed is 

activated and deactivated via the vehicle 

configuration menu.

43

Access

2

Malfunction

An audible signal repeated three times while 

using the function indicates a fault with the 

system.

Have it checked by a CITROËN dealer or a 

qualified workshop.

If the "

Hands-free tailgate access 

self-locking

" option is selected in the 

vehicle menu and after closing the door, 

check that the vehicle is properly locked.

Locking will not take place:

–  if the ignition is on,

–  if one of the doors or the tailgate is open,

–  if a "Keyless Entry and Start" remote 

control is inside the vehicle. 

If a number of gestures with your foot have 

no effect, wait a few seconds before starting 

again.

The system is automatically deactivated in 

heavy rain or with accumulations of snow.

If it does not work, make sure that the 

remote control is not exposed to a source of 

electromagnetic interference (smartphone, 

etc.).

Operation may be affected if using a 

prosthetic leg.

This system may not work correctly if your 

vehicle is fitted with a towbar.

The side door may open or close without 

warning if: 

–  Your vehicle is fitted with a towbar.

–  A trailer is coupled or decoupled.

–  A bicycle carrier is installed or removed.

–  Bicycles are loaded on to or unloaded from 

the bicycle carrier.

–  Something is deposited or lifted behind the 

vehicle.

–  An animal approaches the bumper,

–  The vehicle is washed.

–  The vehicle is being serviced.

–  A wheel is changed. 

To avoid any sudden operation, keep the key 

away from the detection zone (also from the 

boot’s interior sides) or deactivate the function 

in the vehicle configuration menu.

Ensure that no person or object might 

prevent the correct opening or closing of 

the doors.

Be aware of children when operating the 

doors.

Side-hinged rear doors

 

 

►  After first opening the left-hand door, pull the 

lever 

A

 towards you to open the right-hand door.

Closing

►  First close the right-hand door, then the left-

hand door.

If the left-hand door is closed first, a 

buffer stop located on the edge of the 

right-hand door prevents it closing.

If the left-hand side-hinged door is not properly 

closed, the "

door open

" warning lamp lights up 

44

Access

(the right-hand door is not detected). For more 

information on the 

List of warning lamps

 and, 

in particular, the door open warning, refer to the 

corresponding section.

Opening to approximately 

180°

 

 

If fitted to your vehicle, a check strap system 

allows the doors to be opened from about 90° to 

about 180°.

►  Pull the yellow control when the door is open.

The check strap will engage again automatically 

on closing.

When parked with the rear doors open to 

90°, the doors will cover the rear lamps. 

In order to warn other road users travelling in 

the same direction (who may not be aware 

that the vehicle is stationary) of the vehicle's 

position, use a warning triangle or other 

device required by legislation and regulations 

in your country.

Tailgate

Opening

 

 

►  After unlocking the vehicle, pull the handle, 

then raise the tailgate.

Closing

►  Lower the tailgate using the interior grab 

handle, then lock it.

If the tailgate is not properly closed, the "

door 

open

" warning lamp comes on. For more 

information on the 

list of warning and indicator 

lamps

, and in particular the door open warning, 

refer to the corresponding section.

In the event of a malfunction or if you 

experience difficulty opening or closing 

the tailgate, have it checked by a CITROËN 

dealer or a qualified workshop without delay, 

to avoid the issue deteriorating and prevent 

any risk of the tailgate dropping, potentially 

causing serious injury.

Tailgate rear screen

The opening rear screen allows you to access 

the rear of the vehicle directly, without having to 

open the tailgate.

Opening

 

 

After unlocking the vehicle, press this control and 

lift the rear screen to open it.

Closing

Close the rear screen by pressing the centre of 

the glass until it is fully closed.

If the tailgate rear screen is not properly closed, 

the "

door open

" warning lamp comes on. For 

more information on the 

list of warning and 

45

Access

2

indicator lamps

 and in particular the door open 

warning, refer to the corresponding section.

The tailgate and rear screen cannot both 

be open at the same time, to avoid 

damaging them.

Alarm

 

 

(Depending on version)

 

 

 

 

System which protects and provides a deterrent 

against theft and break-ins.

Exterior perimeter monitoring

The system checks for opening of the vehicle.

The alarm is triggered if anyone tries to open a 

door, the boot or the bonnet, for example.

Interior volumetric monitoring

The system only checks for any 

variation in volume in the 

cab

.

The alarm is triggered if anyone 

breaks a window or enters the 

vehicle’s 

cab

; however it is not 

triggered if someone enters the 

loading area

.

The system checks for any 

variation in volume in the 

passenger compartment.

The alarm is triggered if anyone 

breaks a window, enters the 

passenger compartment or 

moves inside the vehicle.

Self-protection function

The system checks whether any of its 

components are out of service.

The alarm is triggered if the battery, the central 

control or the siren wiring is put out of service or 

damaged.

Work on the alarm system

Contact a CITROËN dealer or a qualified 

workshop.

If your vehicle is fitted with Additional 

Heating / Ventilation, volumetric 

monitoring is not compatible with this system.

For more information on 

Additional Heating 

/ Ventilation

, refer to the corresponding 

section.

Locking the vehicle with full 

alarm system

Activation

►  Switch off the ignition and exit the vehicle.

►  Lock or deadlock the vehicle using the 

remote control or with the Keyless Entry and 

Start system.

When the monitoring system is active, the red 

indicator lamp in the button flashes once per 

second and the direction indicators come on for 

about 2 seconds.

The exterior perimeter monitoring is activated 

after 5 seconds and the interior volumetric 

monitoring after 45 seconds.

If an opening (door, tailgate/side-hinged 

doors or bonnet) is not properly closed, 

the vehicle is not locked, but the exterior 

perimeter monitoring will be activated after 45 

seconds, at the same time as the interior 

volumetric monitoring.

46

Access

Deactivation

►  Press the remote control unlocking 

button.

or

►  Unlock the vehicle with the Keyless Entry and 

Start system.

The monitoring system is deactivated: the 

indicator lamp in the button goes off and the 

direction indicators flash for about 2 seconds.

If the vehicle automatically locks itself 

again (as happens if a door or the boot is 

not opened within 30 seconds of unlocking), 

the monitoring system is automatically 

reactivated.

Triggering of the alarm

This is indicated by sounding of the siren 

and flashing of the direction indicators for 30 

seconds.

The monitoring functions remain active until 

the alarm has been triggered ten times in 

succession.

When the vehicle is unlocked, rapid flashing of 

the indicator lamp in the button indicates that the 

alarm was triggered during your absence. When 

the ignition is switched on, this flashing stops 

immediately.

Locking the vehicle 

with exterior perimeter 

monitoring only

Deactivate the interior volumetric monitoring to 

avoid the unwanted triggering of the alarm, in 

certain cases such as:

–  Slightly open window.

–  Washing the vehicle.

–  Changing a wheel.

–  Towing the vehicle.

–  Transport on a ship or ferry.

Deactivating interior volumetric 

monitoring

►  Switch off the ignition and within 10 seconds 

press the alarm button until the indicator lamp is 

on fixed.

►  Exit the vehicle.

►  Immediately lock the vehicle using the remote 

control or the "Keyless Entry and Start" system.

Only exterior perimeter monitoring is activated; 

the red indicator lamp in the button flashes every 

second.

To take effect, this deactivation must be 

performed whenever the ignition is switched 

off.

Reactivating interior volumetric 

monitoring

►  Deactivate exterior perimeter monitoring by 

unlocking the vehicle using the remote control or 

the "Keyless Entry and Start" system.

The indicator lamp in the button goes off.

►  Reactivate the full alarm system by locking 

the vehicle using the remote control or the 

"Keyless Entry and Start" system.

The red indicator lamp in the button once again 

flashes every second.

Locking the vehicle without 

activating the alarm

►  Lock or deadlock the vehicle using the key 

(integral to the remote control) in the driver's 

door lock.

Failure of the remote control

To deactivate the monitoring functions:

►  unlock the vehicle using the key (integral to 

the remote control) in the driver's door lock,

►  Open the door; this sets off the alarm.

►  Upon switching on the ignition the alarm 

stops. The button indicator lamp goes off.

Malfunction

When the ignition is switched on, the fixed 

lighting of the red indicator lamp in the button 

indicates a system malfunction.

Have it checked by a CITROËN dealer or a 

qualified workshop.

47

Access

2

Automatic activation

(Depending on version)

The system is activated automatically 2 minutes 

after the last door or the boot is closed.

►  To avoid triggering the alarm on entering the 

vehicle, first press the unlocking button on the 

remote control or unlock the vehicle using the 

"Keyless Entry and Start" system.

Electric windows

1.

Left-hand front.

2.

Right-hand front.

Operation

►  To open/close the window manually, press/

pull the switch without passing the point of 

resistance; the window stops as soon as the 

switch is released.

►  To open/close the window automatically, 

press/pull the switch fully, beyond the point of 

resistance; the window opens/closes completely 

when the switch is released (pressing the switch 

again stops the movement of the window).

The electric window controls remain 

operational for about 45 seconds after 

the ignition is switched off if the front doors 

are not open.

After that time, the controls are disabled. To 

reactivate them, switch the ignition on again.

Safety anti-pinch

If your vehicle is fitted with the safety anti-pinch 

function, when the window rises and meets an 

obstacle, it stops and partially lowers.

In the event of unwanted opening of the window 

on closing, press the control until the window 

opens completely. Within 4 seconds, pull the 

control until the window closes.

The safety anti-pinch does not operate while 

doing this.

Reinitialising the electric 

windows

After reconnecting the battery, or in the event 

of abnormal window movement, the anti-pinch 

function must be reinitialised.

The anti-pinch function is disabled during the 

following sequence of operations.

For each window:

►  Lower the window fully, then raise it; it will 

rise in steps of a few centimetres each time the 

control is pressed. Repeat the operation until the 

window is fully closed.

►  Continue to pull the control for at least one 

second after the window reaches the closed 

position.

If an electric window meets an obstacle 

during operation, the movement of the 

window must be reversed. To do this, press 

the relevant control.

When the driver operates the passenger 

electric window control, it is important to 

ensure that nothing can prevent the window 

from closing properly.

Pay particular attention to children when 

operating the windows.

Do not put your head or arms through the 

open windows when the vehicle is moving - 

risk of serious injury!

48

Ease of use and comfort

Correct driving position

Before taking to the road and to make the most 

of the ergonomic layout of the instruments and 

controls, carry out these adjustments in the 

following order:

–  the height of the head restraint,

–  the seat backrest angle,

–  the seat cushion height,

–  the longitudinal position of the seat,

–  the height and reach of the steering wheel,

–  the rear view mirror and door mirrors.

 

 

Once these adjustments have been 

made, check the instrument panel can be 

viewed correctly from your driving position.

Manually-adjusted front 

seats

For more information on the 

Seat belts

, 

refer to the corresponding section.

Longitudinal

 

 

►  Raise the control bar and slide the seat 

forwards or backwards.

►  Release the control bar to lock the seat in 

position on one of the notches.

Before moving the seat backwards, 

ensure that there is nothing that might 

prevent the full travel of the seat.

There is a risk of trapping or pinching 

passengers if present in the rear seats or 

jamming the seat if large objects are placed 

on the floor behind the seat.

Height

 

 

►  Pull the control upwards to raise or push it 

downwards to lower, until you obtain the position 

required.

Backrest angle

 

 

►  Depending on equipment, turn the knob 

or pull the control all the way up and tilt the 

backrest forwards or backwards to obtain the 

desired angle.

Lumbar

 

 

49

Ease of use and comfort

3

►  Turn the knob to obtain the desired level of 

lumbar support.

Table position of the driver's 

and/or the front passenger 

seat backrest

 

 

On the front passenger side, this position allows 

long objects to be carried.

On the driver's side, this position allows rear 

passengers to be helped out of the vehicle (by 

the emergency services).

Check that there is no object that could 

interfere with the movement of a seat, 

both above and below.

►  Place the head restraint in the low position, 

and if fitted to your vehicle, raise the armrest and 

fold the table fitted to the back of the seat.

We recommend deactivating the front 

passenger airbag.

 

 

►  Pull the control fully up and tip the backrest 

forward.

To return to the normal position, pull the control 

up to release the backrest, then pull the backrest 

up to its raised position.

When sharp deceleration occurs, objects 

placed on the folded backrest can turn 

into projectiles.

Electric front seat

To avoid discharging the battery, carry 

out these adjustments with the engine 

running.

For more information on the 

Seat belts

, 

refer to the corresponding section.

Longitudinal

 

 

►  Push the control forwards or rearwards to 

slide the seat.

Before moving the seat backwards, 

ensure that there is nothing that might 

prevent the full travel of the seat.

There is a risk of trapping or pinching 

passengers if present in the rear seats or 

jamming the seat if large objects are placed 

on the floor behind the seat.

Seat cushion height

 

 

►  Tilt the control upwards or downwards to 

obtain the desired height.