Kia Sedona (2008 year). Manual - part 140

GEARBOX STATUS 

The status of the gearbox is sent on the CAN network when the CAN network is available. 

OIL PRESSURE SWITCH STATUS 

The status of the oil pressure switch is sent on the CAN network when the CAN network is available. 

FUEL FILTER STATUS 

The FAM receives on digital input the status of the fuel filter (Fuel Filter Input) and sends it (Fuel filter switch) 
on the CAN network. 

WASHER FLUID SENSOR STATUS 

The FAM receives on digital input the status of the washer fluid sensor and sends it on the CAN network. 

If Washer Fluid Low Input is LOW for more than 10 sec, FAM sends the warning message. 

SEAT BELT WARNING STATUS 

The IPM receives on digital input the status of the seat belt switch and sends the seat belt warning on the CAN 
network. 

If the Ignition switch status is in RUN or START when the Seat Belt Sw Input is FASTENED, the seat belt 
warning indicator is blinking for 6 seconds. 

When Seat Belt switch Input is NOT FASTENED, the seat belt warning indicator is blinking for 6 seconds. 

If the Seat Belt switch Input is FASTENED during the 6 seconds, the seat belt warning indicator is blinking till 
the end of the 6 seconds. 

In North America: 

the seat belt warning indicator is blinking when Ignition switch is on the status RUN or START and Seat Belt 
Sw Input is NOT FASTENED. 

PARKING BRAKE INDICATOR 

The indicator manages 3 functions: brake fluid sensor, parking brake warning and vacuum switch. 

The vacuum function is available for diesel engine only 

The FAM receives on digital input the status of the vacuum switch and the ABS EBD warning and sends them 
on the CAN network. 

The status of the vacuum switch and the ABS EBD warning are sent on the CAN network when the CAN 
network is available. 

 

2008 Kia Sedona EX 

2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona

  

Microsoft 

 

Monday, May 24, 2010 4:19:16 PM

Page 29 

© 2006 Mitchell Repair Information Company, LLC. 

The FAM receives on digital input the status of the brake fluid sensor and sends it on the CAN network.

The status of the brake fluid sensor is sent on the CAN network when the CAN network is available. 

The IPM receives on digital input the status of the parking brake switch and by CAN network the status of the 
vacuum switch, the status of the ABS EBD warning, the status of the brake fluid sensor and the speed of the 
vehicle. 

The IPM sends the park brake indicator control on the CAN network. 

The indicator is lighted if the vacuum switch or ABS EBD warning are on or brake fluid sensor is low or park 
brake switch is on. 

If the speed of the vehicle is over 10 km/h and ignition switch is on the status RUN the park brake indicator 
control is blinking at 50% duty in 0.6 second if Parking Brake switch Input is active. In this case Vacuum 
switch, ABS EBD warning and Brake Fluid sensor are ignored. 

The park brake indicator is blinking on the same time that the chime is ringing. If a CAN signal among Vacuum 
switch, EBD warning or Brake Fluid Sens switch is INVALID, out of range or not received this CAN signal is 
considered to be OFF. 

If Vehicle Speed CAN signal is INVALID or not received, it is considered to be 0 kph. 

CHARGING VOLTAGE CONTROL 

The IPM receives on analog input the voltage of generator and sends a warning. 

When the voltage of generator L pass strictly above 10V, the state of the CAN variable. 

TURN INDICATORS STATUS 

The status of the turn indicators are sent on the CAN network when the CAN network is available. 

HIGH BEAM STATUS 

The status of the high beam is sent on the CAN network when the CAN network is available. 

FRONT FOG LAMP STATUS 

The status of the front fog lamp (lightning and state of the bulbs) is sent on the CAN network when the CAN 
network is available. 

DOORS OPEN WARNING 

The RAM receives on digital input the status of the driver door open switch and sends it on the CAN network. 

The RAM receives on digital input the status of the passenger door open switch and sends it on the CAN 
network. 

 

2008 Kia Sedona EX 

2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona

  

Microsoft 

 

Monday, May 24, 2010 4:19:16 PM

Page 30 

© 2006 Mitchell Repair Information Company, LLC. 

The RAM receives on digital input the status of the left sliding door open switch and sends it on the CAN 
network. 

The RAM receives on digital input the status of the right sliding door open switch and sends it on the CAN 
network. 

When vehicle speed is under 10 kph, with ignition key not inserted and any door OPEN, Doors Open Wng Ctrl 
stays ON for 20 min and then is turned OFF. 

TAILGATE OPEN SWITCH STATUS 

When vehicle speed is under 10 kph, ignition key is inserted and Tailgate open switch is OPEN, Tailgate Open 
warning stays ON forever (IPM can enter sleep mode). 

When vehicle speed is under 10 kph, with ignition key not inserted and liftgate open switch is OPEN, Tailgate 
Open warning stays ON for 20 min and then is turned OFF. 

CHIME CONTROL 

1. The chime warns the driver that a problem is occurred. These warning are: 



Seat belt  



Parking on  



Over speed  



Key reminder  



Light Warning  



Doors Open  



Tailgate open warning  

2. Chime sound priority: 



1st: Seatbelt warning  



2nd: Overspeed warning  



3rd: Door open warning  



4th: T/Gate open warning  



5th: Key operated warning  



6th: Parking Brake warning  



7th: Light ON warning  



8th: Key learning sound  

3. If two different warning condition happen at the same time, chime should work only for the highest 

warning condition.  

4. Cluster indicators should work for two warning behavior.  

5. Behavior Description 

 

2008 Kia Sedona EX 

2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona

  

Microsoft 

 

Monday, May 24, 2010 4:19:16 PM

Page 31 

© 2006 Mitchell Repair Information Company, LLC. 

Fig. 34: Warning Behavior Description 
Courtesy of KIA MOTORS AMERICA, INC. 

SEAT BELT WARNING 

The IPM receives on digital input the status of the seat belt switch. 

The chime is activated during 6 second when the seat belt is not fastened. 

The chime will stop immediately if the seat belt is fastened during the 6 seconds of the chime. 

PARK BRAKE WARNING 

The IPM receives on digital input the status of the parking brake switch. 

The IPM receives the speed of the vehicle by the CAN network. 

The chime is activated when the parking brake is on, ignition switch is on RUN and speed vehicle is over 10 
km/h. 

The park brake indicator is blinking at the same time that the chime is ringing. 

OVER SPEED WARNING 

The IPM receives the overspeed warning by the CAN network. 

The chime is activated when the overspeed speed warning is on the state Overspeed. 

KEY REMINDER WARNING 

The IPM receives the status of the key on digital input. 

The IPM receives the status of the driver door open switch by the CAN network. 

The chime is activated when key is inserted and the driver door is open.

 

2008 Kia Sedona EX 

2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona

  

Microsoft 

 

Monday, May 24, 2010 4:19:16 PM

Page 32 

© 2006 Mitchell Repair Information Company, LLC.