Toyota Supra (2023 year). Manual in english - page 21

332

5-1. MOBILITY



Maximum temperature: 140 
°F/60 °C.



Minimum distance from sen-
sors, cameras, seals, and 
lights: 12 in/30 cm.

Safety information

WARNING

When washing with an open fuel 

filler flap, damage may occur. 

There is a danger of damage to 

property. Close the fuel filler flap 

before washing. Clean dirt behind 

the fuel filler flap with a cloth.

Steam blaster and 
high-pressure washer

Safety information

NOTICE

When cleaning with high-pressure 

washers, components can be 

damaged due to the pressure or 

temperatures being too high. 

There is a risk of damage to prop-

erty. Maintain sufficient distance 

and do not spray too long continu-

ously. Follow the operating 

instructions for the high-pressure 

washer.

Distances and temperature

Automatic vehicle washes

Safety information

NOTICE

Water can penetrate in the wind-

shield area due to high-pressure 

washers. There is a risk of dam-

age to property. Avoid high-pres-

sure washers.

NOTICE

Improper use of automatic vehicle 

washes can cause damage to the 

vehicle. There is a risk of damage 

to property. Follow the following 

instructions:

●

Give preference to cloth vehicle 

washes or those that use soft 

brushes in order to avoid paint 

damage.

●

Avoid vehicle washes with 

guide rails higher than 4 in/10 

cm to avoid damage to the 

chassis.

●

Observe the tire width of the 

guide rail to avoid damage to 

tires and rims.

●

Fold in exterior mirrors to avoid 

damage to the exterior mirrors.

●

Deactivate the wiper and, if nec-

essary, rain sensor to avoid 

damage to the wiper system.

●

Do not treat the convertible top 

with wax. Ensure that a cycle 

without wax or a special cycle 

for convertibles is available to 

avoid damage to the convertible 

top.

333

5-1. MOBILITY

5

MOBILITY

■

Safety information

■

General information

In a vehicle wash, the vehicle 
must be able to roll freely.
To roll or push the vehicle, refer 
to page 134.
Some vehicle washes do not 
permit persons in the vehicle. 
The vehicle cannot be locked 
from the outside when in selec-
tor lever position N. A signal 
sounds when an attempt is 
made to lock the vehicle.

Make sure that the remote con-
trol is in the vehicle.
Switch on drive-ready state, 
refer to page 47.

Do not rub wet lights dry and do 
not use abrasive, acidic clean-
ing agents or cleaning agents 
containing alcohol.
Soak areas that have been dirt-
ied, for instance from insects, 
with shampoo and wash off with 

water.
Thaw ice with de-icing spray; do 
not use an ice scraper.

After washing the vehicle, apply 
the brakes briefly to dry them; 
otherwise, braking action can be 
reduced. The heat generated 
during braking dries brake discs 
and brake pads and protects 
them against corrosion.
Completely remove all residues 
on the windows, to minimize 
loss of visibility due to smearing 
and to reduce wiper noises and 
wiper blade wear.

Regular care contributes to driv-

Driving into a vehicle wash

NOTICE

Selector lever position P is auto-

matically engaged when standby 

state is switched off. There is a 

risk of damage to property. Do not 

switch standby state off in vehicle 

washes.

Driving out of a vehicle wash

Lights

After washing the vehicle

Vehicle care

Vehicle care products

Safety information

WARNING

Cleansers can contain sub-

stances that are dangerous and 

harmful to your health. There is a 

risk of injury. When cleaning the 

interior, open the doors or win-

dows. Only use products intended 

for cleaning vehicles. Follow the 

instructions on the container.

Vehicle paint

General information

334

5-1. MOBILITY

ing safety and value retention. 
Environmental influences in 
areas with elevated air pollution 
or natural contaminants, such as 
tree resin or pollen can affect 
the vehicle's paintwork. Tailor 
the frequency and extent of your 
vehicle care to these influences.
Aggressive substances such as 
spilled fuel, oil, grease or bird 
droppings, must be removed 
immediately to prevent the finish 
from being altered or discolored.

Perform the following to protect 
the vehicle.



Working from top to bottom, 
liberally apply water to the 
vehicle body, wheel wells and 
underside of the vehicle to 
remove any dirt and dust.



Wash the vehicle body using 
a sponge or soft cloth, such 
as a chamois.



For hard-to-remove marks, 
use a neutral detergent and 
rinse thoroughly with water.



Wipe away any water.



Never use wax or abrasive 
compounds.

Matte finish

Safety information

WARNING

Improperly performed work on the 

vehicle paint can lead to a failure 

or malfunction of the radar sen-

sors and thereby result in a safety 

risk. There is a risk of accidents or 

risk of damage to property. Have 

paintwork or paintwork repairs on 

bumpers of vehicles with radar 

sensors performed by your Toyota 

dealer only.

NOTICE

■

To prevent paint deteriora-

tion and corrosion on the 

body and components (alumi-

num wheels etc.)

Observe the following precau-

tions:

●

Wash the vehicle immediately in 

the following cases:

• After driving near the sea coast

• After driving on salted roads

• If coal tar or tree sap is present 

on the paint surface

• If dead insects, insect droppings 

or bird droppings are present on 

the paint surface

• After driving in an area contami-

nated with soot, oily smoke, 

mine dust, iron powder or chem-

ical substances

• If the vehicle becomes heavily 

soiled with dust or mud

• If liquids such as benzene and 

gasoline are spilled on the paint 

surface

●

If the paint is chipped or 

scratched, have it repaired 

immediately.

335

5-1. MOBILITY

5

MOBILITY

Remove dust from the leather 
regularly, using a cloth or vac-
uum cleaner.
Otherwise, particles of dust and 
road grime chafe in pores and 
folds, and lead to increased 
wear and premature degrada-
tion of the leather surface.
To guard against discoloration, 
such as from clothing, clean 
leather and provide leather care 
roughly every two months.
Clean light-colored leather more 
frequently because soiling on 
such surfaces is substantially 
more visible.
Use leather care products; oth-
erwise, dirt and grease will grad-
ually break down the protective 

layer of the leather surface.

Clean synthetic leather regularly 
with a damp microfiber cloth or 
vacuum cleaner.
Otherwise, dust and road grime 
particles will rub into pores and 
folds, causing significant abra-
sion and premature degrada-
tion of the surface.
In case of major soiling, use a 
moist soft sponge or microfiber 
cloth with suitable interior clean-
ers.
Immediately remove aggressive 
substances such as sunscreen 
to prevent the synthetic leather 
from being altered or discolored.

Vacuum the upholstery regularly 
with a vacuum cleaner.
If upholstery is very dirty, for 
instance with beverage stains, 
use a soft sponge or microfiber 
cloth with a suitable interior 
cleaner.
Clean the upholstery down to 
the seams using large sweeping 
motions. Avoid rubbing the 
material vigorously.

NOTICE

●

To prevent the wheels from cor-

roding, remove any dirt and 

store in a place with low humid-

ity when storing the wheels.

For the matte finish, pay attention 

to the following as well:

●

If anything is spilled on a 

painted surface, wipe it off as 

soon as possible. If spilled 

washer fluid or alkaline fluids 

are left as is, the paint in the 

affected area may deteriorate, 

causing blemishing.

●

Do not wax or apply coating to 

the vehicle. Doing so may 

cause a change in the body sur-

face's texture or irregularities in 

the paint.

Leather care

Synthetic leather care

Upholstery material care

General information

336

5-1. MOBILITY

When cleaning the vehicle, use 
only neutral wheel cleaners hav-
ing a pH value from 5 to 9. Do 
not use abrasive cleaning 
agents or steam jets above 140 
°F/60 °C. Follow the manufac-
turer's instructions.
Aggressive, acidic or alkaline 
cleaning agents can destroy the 
protective layer of adjacent 
components, such as the brake 
disc.
After cleaning, apply the brakes 
briefly to dry them. The heat 
generated during braking dries 
brake discs and brake pads and 
protects them against corrosion.

Carefully clean components 
such as the radiator grille or 
door handles with plenty of 
water, possibly with shampoo 
added, particularly when they 

have been exposed to road salt.

Environmental influences can 
cause surface soiling of rubber 
parts and a loss of gloss. Use 
only water and suitable cleaning 
agents for cleaning.
Treat especially worn rubber 
parts with rubber care agents at 
regular intervals. When cleaning 
rubber seals, do not use any sili-
con-containing vehicle care 
products in order to avoid dam-
age or noises.

The wiper blades are cleaned by 
using the washer system.
Avoid cleaning the wiper blades 
manually, as this may reduce 
wiper performance.

Clean with a microfiber cloth.
Dampen cloth lightly with water.
Do not soak the roofliner.

Safety information

NOTICE

Open hook-and-loop fasteners on 

articles of clothing can damage 

the seat covers. There is a risk of 

damage to property. Ensure that 

any hook-and-loop fasteners are 

closed.

Caring for special compo-
nents

Light-alloy wheels

Chrome surfaces

Rubber components

Wiper blades

Plastic components

NOTICE

Cleansers that contain alcohol or 

solvents, such as lacquer thin-

ners, heavy-duty grease remov-

ers, fuel, or such, can damage 

plastic parts. There is a risk of 

damage to property. Clean with a 

microfiber cloth. Dampen cloth 

lightly with water.

337

5-1. MOBILITY

5

MOBILITY

Dirty belt straps impede the reel-
ing action and thus have a neg-
ative impact on safety.
Use only a mild soapy solution 
for cleaning the installed belt 
straps.
Safety belts should only be 
allowed to retract if they are dry.

The floor mats can be removed 
from the car's interior for clean-
ing.
If the floor carpets are very dirty, 

clean with a microfiber cloth and 
water or a textile cleaner. To 
prevent matting of the carpet, 
rub back and forth in the direc-
tion of travel only.

To clean sensors and camera 
lenses, use a cloth moistened 
with a small amount of glass 
detergent.

Use a dry, clean antistatic micro-
fiber cloth.
Clean the protective glass of the 
Head-up Display, refer to page 
155, using a microfiber cloth and 
commercially available 
dish-washing soap.

Safety belts

WARNING

Chemical cleansers can destroy 

the safety belt webbing. Missing 

protective effect of the safety 

belts. There is a risk of injuries or 

danger to life. Use only a mild 

soapy solution for cleaning the 

safety belts.

Carpets and floor mats

WARNING

Objects in the driver's floor area 

can limit the pedal distance or 

block a depressed pedal. There is 

a risk of an accident. Stow objects 

in the vehicle such that they are 

secured and cannot enter into the 

driver's floor area. Use floor mats 

that are suitable for the vehicle 

and can be safely attached to the 

floor. Do not use loose floor mats 

and do not layer several floor 

mats. Make sure that there is suf-

ficient clearance for the pedals. 

Ensure that the floor mats are 

securely fastened again after they 

were removed, for instance for 

cleaning.

Sensors and camera lenses

Displays, screens, and pro-
tective glass of the Head-up 
Display

NOTICE

Chemical cleansers, moisture or 

fluids of any kind can damage the 

surface of displays and screens. 

There is a risk of damage to prop-

erty. Clean with a clean, antistatic 

microfiber cloth.

NOTICE

The surface of displays can be 

damaged with improper cleaning. 

There is a risk of damage to prop-

erty. Avoid pressure that is too 

high and do not use any scratch-

ing materials.

338

5-1. MOBILITY

When the vehicle is shut down 
for longer than three months, 
special measures must be 
taken. Further information is 
available from your Toyota 
dealer.

Long-term vehicle storage

340

6-1. REFERENCE

6-1.REFERENCE

This chapter describes all stan-
dard, country-specific and 
optional features offered with 
the series. It also describes fea-
tures and functions that are not 
necessarily available in your 
vehicle, e.g., due to the selected 
options or country versions. This 
also applies to safety-related 
functions and systems. When 
using these functions and sys-
tems, the applicable laws and 

regulations must be observed.

The technical data and specifi-
cations in this Owner's Manual 
are used as guidance values. 
The vehicle-specific data can 
deviate from this, for instance 
due to the selected special 
equipment, country version or 
country-specific measurement 
method. Detailed values can be 
found in the approval docu-
ments, on labels on the vehicle 
or can be obtained from your 
Toyota dealer.

The dimensions can vary depending on the model version, equip-
ment or country-specific measurement method.
The specified heights do not take into account attached parts, for 
instance a roof antenna, roof racks or spoiler. The heights can devi-
ate, for instance due to the selected special equipment, tires, load 
and chassis version.

*1

:2.0 models

*2

:3.0 and 3.0 Premium models

Technical data

Vehicle features and 
options

General information

Dimensions

Width with mirrors

in/mm

79.8 / 2026

Width without mirrors

in/mm

73.0 / 1854

Height

in/mm

51.1 / 1299

*1

50.9 / 1292

*2

Length

in/mm

172.5 / 4381

Wheelbase

in/mm

97.2 / 2470

Smallest turning radius diam.

ft/m

36.1 / 11

341

6-1. REFERENCE

6

REFERENCE

*1

:Vehicles with manual transmission

*2

:Vehicles with automatic transmission

Observe further information on fuel quality, refer to page 301.

Weights

2.0 models

Approved gross vehicle weight

lbs/kg

3770 / 1710

Load

lbs/kg

430 / 195

Approved front axle load

lbs/kg

1819 / 825

Approved rear axle load

lbs/kg

2006 / 910

3.0 and 3.0 Premium models

Approved gross vehicle weight

lbs/kg

3990 / 1810

*1

4001 / 1815

*2

Load

lbs/kg

553 / 251

*1

542 / 246

*2

Approved front axle load

lbs/kg

1907 / 865

Approved rear axle load

lbs/kg

2127 / 965

Capacities

Fuel tank, approx.

US gal/liters

13.7 / 52

Engine

Model

B46B20O1

B58B30O1

Type

4-cylinder in line, 4-cycle, 
gasoline (with turbo-
charger)

6-cylinder in line, 4-cycle, 
gasoline (with turbo-
charger)

Bore and stroke

3.23 



 3.72 in. (82.0 



 94.6  

mm)

3.23 



 3.72 in. (82.0 



 94.6  

mm)

Displacement

121.93 cu. in. (1998 cm

3

)

182.95 cu. in. (2998 cm

3

)

342

6-1. REFERENCE

See the further information on engine oil grade, refer to page 302.



Vehicles without LSD (Limited Slip Differential)



Vehicles with LSD (Limited Slip Differential)

Engine oil

Gasoline Engine

Toyota Genuine Motor Oil SN 0W-20 C5 for GR Toyota Supra

BMW Longlife-17 FE+ 0W-20

Cooling system

Coolant type

Antifreeze and Corrosion Inhibitor Frostox HT-12

Manual transmission

Fluid type

Manual Transmission Fluid MTF-LT-5

Automatic transmission

Fluid type

Automatic Gearbox Oil ATF 3+

Differential

Oil type and viscosity

Hypoid Axle Oil G3

Oil type and viscosity

Hypoid Axle Oil G4

Brakes

Fluid type

Brake Fluid DOT 4, Low Viscosity