Toyota 86 (2023 year). Manual in english

287

Maintena

nce
a

nd ca

Maintenance and care

6-1. Maintenance and care

Cleaning and protecting the

vehicle exterior ..........

288

Cleaning and protecting the

vehicle interior ...........

291

Cleaning and protecting the

Ultrasuede

area .......

293

6-2. Maintenance

Maintenance requirements

..................................

295

General maintenance..

296

Emission inspection and

maintenance (I/M) pro-
grams ........................

299

6-3. Do-it-yourself mainte-

nance

Do-it-yourself service pre-

cautions.....................

300

Hood ...........................

302

Positioning a floor jack

..................................

303

Engine compartment...

305

Tires ............................

312

Replacing the tire ........

319

Tire inflation pressure..

323

Wheels ........................

325

Air conditioning filter....

327

Electronic key battery..

328

Checking and replacing

fuses..........................

330

Headlight aim ..............

332

Light bulbs...................

333

288

6-1. Maintenance and care

6-1.Maintenance and care



Working from top to bottom,
liberally apply water to the
vehicle body, wheel wells and
underside of the vehicle to
remove any dirt and dust.



Wash the vehicle body using
a sponge or soft cloth, such
as a chamois.



If very dirty, use a car wash
soap that does not contain
abrasives and then thor-
oughly rinse with water.



Wipe away any water.



Wax the vehicle when the
waterproof coating deterio-
rates.

If water does not bead on a clean
surface, apply wax when the vehi-
cle body is cool.

■

Automatic car washes

●

Fold the mirrors before washing

the vehicle. Start washing from the

front of the vehicle. Make sure to

extend the mirrors before driving.

●

Brushes used in automatic car

washes may scratch the vehicle

surface, parts (wheel, etc.) and

harm your vehicle’s paint.

■

High pressure car washes

As water may enter the cabin, do

not bring the nozzle tip near the

gaps around the doors or perimeter

of the windows, or spray these

areas continuously.

■

When using a car wash

If the door handle becomes wet

while the electronic key is within the

effective range, the door may lock

and unlock repeatedly. In that case,

follow the following correction pro-

cedures to wash the vehicle:

●

Place the key in a position 6 ft. (2

m) or more separate from the

vehicle while the vehicle is being

washed. (Take care to ensure that

the key is not stolen.)

●

Set the electronic key to bat-

tery-saving mode to disable the

smart key system. (



P.111)

■

Wheels and wheel ornaments

(vehicles without matte painted

wheels)

●

Remove any dirt immediately by

using a neutral detergent.

●

Wash detergent off with water

immediately after use.

●

To protect the paint from damage,

make sure to observe the follow-

ing precautions.

• Do not use acidic, alkaline or

abrasive detergent

• Do not use hard brushes

• Do not use detergent on the

wheels when they are hot, such

as after driving or parking in hot

weather

■

Wheels and wheel ornaments

(vehicles with matte painted

wheels)

As matte painted wheels require dif-

ferent cleaning methods than con-

ventional wheels, be sure to

observe the following. For details,

consult your Toyota dealer.

●

Remove dirt using water. If the

wheels are excessively dirty, use

a sponge or soft cloth dampened

Cleaning and protect-

ing the vehicle exte-

rior

Perform cleaning in a man-
ner appropriate to each
component and its material.

Cleaning instructions

289

6-1. Maintenance and care

Maintena

nce
a

nd ca

with a diluted neutral detergent to

remove the dirt.

●

To protect the matte paint from

damage, make sure to observe

the following precautions.

• Do not scrub or polish the wheels

using a brush or dry cloth

• Do not use any wheel coatings or

abrasive detergents

■

Brake pads and calipers

Rust may form if the vehicle is

parked with wet brake pads or disc

rotors, causing them to stick. Before

parking the vehicle after it is

washed, drive slowly and apply the

brakes several times to dry the

parts.

■

Bumpers

Do not scrub with abrasive cleaners.

■

Plated portions

If dirt cannot be removed, clean the

parts as follows:

●

Use a soft cloth dampened with an

approximately 5% solution of neu-

tral detergent and water to clean

the dirt off.

●

Wipe the surface with a dry, soft

cloth to remove any remaining

moisture.

●

To remove oily deposits, use alco-

hol wet wipes or a similar product.

WARNING

■

When washing the vehicle

Do not apply water to the inside of

the engine compartment. Doing

so may cause the electrical com-

ponents, etc. to catch fire.

■

Precautions regarding the

exhaust pipes

Exhaust gasses cause the

exhaust pipes and rear bumper

diffusers to become quite hot.

When washing the vehicle, be

careful not to touch the pipes and

diffusers until they have cooled

sufficiently, as touching hot

exhaust pipes and rear bumper

diffusers can cause burns.

■

Precaution regarding the rear

bumper

If the paint of the rear bumper is

chipped or scratched, the follow-

ing systems may not function cor-

rectly. If this occurs, consult your

Toyota dealer.

●

BSD/RCTA (if equipped)

●

RAB (if equipped)

NOTICE

■

To prevent paint deteriora-

tion and corrosion on the

body and components (alumi-

num wheels, etc.)

●

Wash the vehicle immediately in

the following cases:

• After driving near the sea coast

• After driving on salted roads

• If coal tar or tree sap is present

on the paint surface

• If dead insects, insect droppings

or bird droppings are present on

the paint surface

• After driving in an area contami-

nated with soot, oily smoke,

mine dust, iron powder or chem-

ical substances

• If the vehicle becomes heavily

soiled with dust or mud

290

6-1. Maintenance and care

NOTICE

• If liquids such as benzene and

gasoline are spilled on the paint

surface

●

If the paint is chipped or

scratched, have it repaired

immediately.

●

To prevent the wheels from cor-

roding, remove any dirt and

store in a place with low humid-

ity when storing the wheels.

■

Protective film for side sill

plates (if equipped)

Make sure to remove the protec-

tive film. Failure to do so may

cause rust, depending on condi-

tions.

■

Cleaning the exterior lights

●

Wash carefully. Do not use

organic substances or scrub

with a hard brush. This may

damage the surfaces of the

lights.

●

Do not apply wax to the sur-

faces of the lights.

Wax may cause damage to the

lenses.

■

To prevent damage to the

windshield wiper arms

When lifting the wiper arms away

from the windshield, pull the driver

side wiper arm upward first, and

repeat for the passenger side.

When returning the wipers to their

original position, do so from the

passenger side first.

■

When using a high pressure

car wash

●

When washing the vehicle, do

not spray the camera or its sur-

rounding area directly with a

high pressure washer. Shock

applied from high pressure

water may cause the device to

not operate normally.

●

Do not bring the nozzle tip close

to boots (rubber or resin manu-

factured cover), connectors or

the following parts. The parts

may be damaged if they come

into contact with high-pressure

water.

• Traction related parts

• Suspension parts

• Steering parts

• Brake parts

●

Keep the cleaning nozzle at

least 11.9 in. (30 cm) away from

the vehicle body. Otherwise

resin section, such as moldings

and bumpers, may be deformed

and damaged.

Also, do not continuously hold the

nozzle in the same place.

●

Do not spray the lower part of

the windshield continuously.

If water enters the air conditioning

system intake located near the

lower part of the windshield, the

air conditioning system may not

operate correctly.

●

Do not wash the underside of

the vehicle using a high pres-

sure car washer.

291

6-1. Maintenance and care

Maintena

nce
a

nd ca



Remove dirt and dust using a
vacuum cleaner. Wipe dirty
surfaces with a cloth damp-
ened with lukewarm water.



If dirt cannot be removed,
wipe it off with a soft cloth
dampened with neutral deter-
gent diluted to approximately
1%.

Wring out any excess water from
the cloth and thoroughly wipe off
remaining traces of detergent and
water.

■

Shampooing the carpets

There are several commercial foam-

ing-type cleaners available. Use a

sponge or brush to apply the foam.

Rub in overlapping circles. Do not

use water. Wipe dirty surfaces and

let them dry. Excellent results are

obtained by keeping the carpet as

dry as possible.

■

Handling the seat belts

Clean with mild soap and lukewarm

water using a cloth or sponge. Also

check the belts periodically for

excessive wear, fraying or cuts.

■

Meter visor

Do not place anything on top of

meter visor. The color of the meter

visor may transfer.

Cleaning and protect-

ing the vehicle interior

Perform cleaning in a man-
ner appropriate to each
component and its material.

Protecting the vehicle
interior

WARNING

■

Water in the vehicle

●

Do not splash or spill liquid in

the vehicle.

Doing so may cause electrical

components, etc. to malfunction

or catch fire.

●

Do not get any of the SRS com-

ponents or wiring in the vehicle

interior wet. (



P.29)

An electrical malfunction may

cause the airbags to deploy or not

function properly, resulting in

death or serious injury.

■

Cleaning the interior (espe-

cially instrument panel)

Do not use polish wax or polish

cleaner. The instrument panel

may reflect off the windshield,

obstructing the driver’s view and

leading to an accident, resulting in

death or serious injury.

NOTICE

■

Cleaning detergents

●

Do not use the following types

of detergent, as they may dis-

color the vehicle interior or

cause streaks or damage to

painted surfaces:

• Non-seat portions: Organic sub-

stances such as benzene or

gasoline, alkaline or acidic solu-

tions, dye, and bleach

• Seats: Alkaline or acidic solu-

tions, such as thinner, benzene,

and alcohol

●

Do not use polish wax or polish

cleaner. The instrument panel’s

or other interior part’s painted

surface may be damaged.

292

6-1. Maintenance and care



Remove dirt and dust using a
vacuum cleaner.



Wipe off any excess dirt and
dust with a soft cloth damp-
ened with diluted detergent.

Use a diluted water solution of
approximately 5% neutral wool
detergent.



Wring out any excess water
from the cloth and thoroughly
wipe off all remaining traces

NOTICE

●

Do not use a chemical agent

containing silicone

(highly-polymerized silicon com-

pound) when cleaning any of

the electrical appliances such

as the air conditioning, all

switches and their surrounding

areas.

If silicon (highly-polymerized sil-

icon compound) contacts these

components, it may cause the

electrical appliances to malfunc-

tion.

■

Preventing damage to leather

surfaces

Observe the following precautions

to avoid damage to and deteriora-

tion of leather surfaces:

●

Remove any dust or dirt from

leather surfaces immediately.

●

Do not expose the vehicle to

direct sunlight for extended peri-

ods of time. Park the vehicle in

the shade, especially during

summer.

●

Do not place items made of

vinyl, plastic, or containing wax

on the upholstery, as they may

stick to the leather surface if the

vehicle interior heats up signifi-

cantly.

■

Water on the floor

Do not wash the vehicle floor with

water.
Vehicle systems such as the

audio system may be damaged if

water comes into contact with

electrical components such as the

audio system above or under the

floor of the vehicle. Water may

also cause the body to rust.

■

When cleaning the inside of

the windshield

Do not allow glass cleaner to con-

tact the lens. Also, do not touch

the lens. (



P.174)

■

Cleaning the inside of the rear

window

●

Do not use glass cleaner to

clean the rear window, as this

may cause damage to the rear

window defogger heater wires.

Use a cloth dampened with

lukewarm water to gently wipe

the window clean. Wipe the win-

dow in strokes running parallel

to the heater wires.

●

Be careful not to scratch or

damage the heater wires.

■

When cleaning the instrument

panel

When small grains of sand and so

forth have gotten into instrument

panel’s surface and cannot be

wiped away using a cloth, use a

clay bar without adding water.

Forcibly trying to wipe the surface

clean with a brush or sponge may

scratch the surface or fragments

of the cloth may be left in the sur-

face.

Cleaning the leather areas

293

6-1. Maintenance and care

Maintena

nce
a

nd ca

of detergent.



Wipe the surface with a dry,
soft cloth to remove any
remaining moisture.
Allow the leather to dry in a
shaded and ventilated area.

■

Caring for leather areas

Toyota recommends cleaning the

interior of the vehicle at least twice a

year to maintain the quality of the

vehicle’s interior.



Remove dirt and dust using a
vacuum cleaner.



Wipe it off with a soft cloth
dampened with neutral deter-
gent diluted to approximately
1%.



Wring out any excess water
from the cloth and thoroughly
wipe off remaining traces of
detergent and water.

: If equipped

: Ultrasuede

is a registered trade-

mark of Toray Industries, Inc.



Periodic cleaning once a
month is recommended.

Wipe the entire Ultrasuede

area with a soft cloth that has
been dampened with luke-
warm water (approximately
104°F [40°C]) and squeezed
out.

Do not wipe too hard. Doing so may
make the Ultrasuede

upholstery

surface become uneven. Also, only

use a clean cloth.

Once dry, brush the area with
a soft brush.

■

Removing stuck-on dirt

If fluff is attached to your clothes,

etc. remove it by brushing it off with

a soft brush. If this does not remove

the fluff, remove it using adhesive

Cleaning the synthetic
leather areas

Cleaning and protect-

ing the Ultra-

suede

area

Perform cleaning in a man-
ner appropriate to each
component and its material.

Day-to-day cleaning

NOTICE

■

When cleaning the Ultra-
suede

surfaces

As Ultrasuede

is a suede-like

product, do not brush it strongly.

Doing so may cause fluff or pilling.

294

6-1. Maintenance and care

tape.



If liquid is spilled, lightly pat
the area with a tissue paper or
similar to soak up the liquid.



When mud, coffee, etc., has
dried on the Ultrasuede

upholstery, remove it by lightly
brushing the area with a soft
brush or similar.

We recommend using a vacuum
cleaner to clean up the area after
the above has been performed.

When a stain cannot be
removed using the above proce-
dures, remove it by performing
the following:

Lightly wipe the stained area
from the outside to the inside
from multiple angles with a
soft cloth that has been
dampened with lukewarm
water (approximately 104°F
[40°C]) and squeezed out.

Do not wipe too hard. Doing so may
make the Ultrasuede

upholstery

surface become uneven. Also, only

use a clean cloth.

If the Ultrasuede

upholstery

surface becomes uneven,
lightly brush it with a soft
brush.

Allow the surface to dry com-
pletely.

You will need the following
items:



A cloth that has been damp-
ened with benzene



A dry cloth

Using a dry cloth or tissue
paper, wipe away as much of
the oil as possible to prevent
the stained area from
expanding.

After patting the area from
the outside to the inside from
multiple angles using the
cloth dampened with ben-
zene, soak up the oil and
benzene that floats up by pat-
ting the area with a dry cloth.

If the Ultrasuede

upholstery

surface becomes uneven,
lightly brush it with a soft
brush.

Liquid stains

NOTICE

■

When soaking up spilled liq-

uids

Do not press down too firmly with

the cloth, tissue paper etc., as

doing so may cause the liquid to

further penetrate the material,

making soaking up the liquid more

difficult.

Oily stains

295

6-2. Maintenance

Maintena

nce
a

nd ca

6-2.Maintenance

■

Repair and replacement

It is recommended that genuine

Toyota parts be used for repairs to

ensure performance of each sys-

tem. If non-Toyota parts are used in

replacement or if a repair shop other

than a Toyota dealer performs

repairs, confirm the warranty cover-

age.

■

Allow inspection and repairs to

be performed by a Toyota

dealer

●

Toyota technicians are

well-trained specialists and are

kept up to date with the latest ser-

vice information. They are well

informed about the operation of all

systems on your vehicle.

●

Keep a copy of the repair order. It

proves that the maintenance that

has been performed is under war-

ranty coverage. If any problem

should arise while your vehicle is

under warranty, your Toyota

dealer will promptly take care of it.

General maintenance should be
performed on a daily basis. This
can be done by yourself or by a
Toyota dealer.

Scheduled maintenance should
be performed at specified inter-
vals according to the mainte-
nance schedule.

For details about maintenance
items and schedules, refer to the
“Scheduled Maintenance Guide” or
“Owner’s Manual Supplement”.

Maintenance require-

ments

To ensure safe and econom-
ical driving, day-to-day care
and regular maintenance
are essential. It is the
owner’s responsibility to
perform regular checks.
Toyota recommends the
maintenance below.

WARNING

■

If your vehicle is not properly

maintained

Improper maintenance could

result in serious damage to the

vehicle and possible death or seri-

ous injury.

■

Handling of the battery

●

Engine exhaust, some of its

constituents, and a wide variety

of automobile components con-

tain or emit chemicals known to

the State of California to cause

cancer and birth defects and

other reproductive harm. Work

in a well ventilated area.

●

Oils, fuels and fluids contained

in vehicles as well as waste pro-

duced by component wear con-

tain or emit chemicals known to

the State of California to cause

cancer and birth defects or

other reproductive harm. Avoid

exposure and wash any

affected area immediately.

●

Battery posts, terminals and

related accessories contain lead

and lead compounds which are

known to cause brain damage.

Wash your hands after han-

dling. (



P.309)

General maintenance

Scheduled maintenance

296

6-2. Maintenance

You can perform some mainte-
nance procedures by yourself.
Please be aware that do-it-your-
self maintenance may affect
warranty coverage.

The use of Toyota repair manuals is
recommended.
For details about warranty cover-
age, refer to the separate “Owner’s
Warranty Information Booklet” or
“Owner’s Manual Supplement”.

Do-it-yourself mainte-
nance

General maintenance

Listed below are the general
maintenance items that
should be performed at the
intervals specified in the
“Owner’s Warranty Informa-
tion Booklet” or “Owner’s
Manual Supplement/Sched-
uled Maintenance Guide”. It
is recommended that any
problem you notice should
be brought to the attention
of your Toyota dealer or
qualified service shop for
advice.

WARNING

■

If the engine is running

Turn the engine off and ensure

that there is adequate ventilation

before performing maintenance

checks.

Engine compartment

Items

Check points

Battery

Check the connec-
tions. (



P.309)

Brake
fluid/Clutch
fluid

Is the brake fluid
and clutch fluid at
the correct level?
(



P.308)

Engine coolant

Is the engine cool-
ant at the correct
level? (



P.307)

Engine oil

Is the engine oil at
the correct level?
(



P.305)

297

6-2. Maintenance

Maintena

nce
a

nd ca

Exhaust sys-
tem

There should not
be any fumes or
strange sounds.

Radiator/con-
denser

The radiator and
condenser should
be free from for-
eign objects.
(



P.308)

Washer fluid

Is there sufficient
washer fluid?
(



P.311)

Vehicle interior

Items

Check points

Accelerator
pedal

• The accelerator

pedal should
move smoothly
(without uneven
pedal effort or
catching).

Automatic
transmission
“Park” mecha-
nism

• When parked on

a slope and the
shift lever is in P,
is the vehicle
securely
stopped?

Brake pedal

• Does the brake

pedal move
smoothly?

• Does the brake

pedal have
appropriate
clearance from
the floor?

• Does the brake

pedal have the
correct amount
of free play?

Items

Check points

Brakes

• The vehicle

should not pull to
one side when
the brakes are
applied.

• The brakes

should work
effectively.

• The brake pedal

should not feel
spongy.

• The brake pedal

should not get
too close to the
floor when the
brakes are
applied.

Clutch pedal

• Does the clutch

pedal move
smoothly?

• Does the clutch

pedal have
appropriate
clearance from
the floor?

• Does the clutch

pedal have the
correct amount
of free play?

Head
restraints

• Do the head

restraints move
smoothly and
lock securely?

Indica-
tors/buzzers

• Do the indica-

tors and buzzers
function prop-
erly?

Lights

• Do all the lights

come on?

Items

Check points

298

6-2. Maintenance

Parking brake

• Does the park-

ing brake move
smoothly?

• When parked on

a slope and the
parking brake is
on, is the vehicle
securely
stopped?

Seat belts

• Do the seat belts

operate
smoothly?

• The seat belts

should not be
damaged.

Seats

• Do the seat con-

trols operate
properly?

Steering wheel

• Does the steer-

ing wheel rotate
smoothly?

• Does the steer-

ing wheel have
the correct
amount of free
play?

• There should not

be any strange
sounds coming
from the steer-
ing wheel.

Items

Check points

Vehicle exterior

Items

Check points

Doors/trunk

• Do the

doors/trunk oper-
ate smoothly?

Engine hood

• Does the engine

hood lock system
work properly?

Fluid leaks

• There should not

be any signs of
fluid leakage
after the vehicle
has been parked.

Tires

• Is the tire infla-

tion pressure
correct?

• The tires should

not be damaged
or excessively
worn.

• Have the tires

been rotated
according to the
maintenance
schedule?

• The wheel nuts

should not be
loose.

Windshield
wipers

• The wiper blades

should not show
any signs of
cracking, split-
ting, wear, con-
tamination or
deformation.

• The wiper blades

should clear the
windshield with-
out streaking or
skipping.

299

6-2. Maintenance

Maintena

nce
a

nd ca

The OBD system determines
that a problem exists some-
where in the emission control
system. Your vehicle may not
pass the I/M test and may need
to be repaired. Contact your
Toyota dealer to service the
vehicle.



When the battery is discon-
nected or discharged

Readiness codes that are set
during ordinary driving are erased.
Also, depending on your driving
habits, the readiness codes may
not be completely set.



When the fuel tank cap is
loose

The malfunction indicator lamp
comes on indicating a temporary
malfunction and your vehicle may
not pass the I/M test.

The error code in the OBD sys-
tem will not be cleared unless
the vehicle is driven 40 or more
times.

Contact your Toyota dealer to
prepare the vehicle for re-test-
ing.

Emission inspection

and maintenance (I/M)

programs

Some states have vehicle
emission inspection pro-
grams which include OBD
(On Board Diagnostics)
checks. The OBD system
monitors the operation of
the emission control sys-
tem.

If the malfunction indica-
tor lamp comes on

Your vehicle may not pass
the I/M test in the follow-
ing situations:

When the malfunction
indicator lamp still
remains on after several
driving trips

If your vehicle does not
pass the I/M test

300

6-3. Do-it-yourself maintenance

6-3.Do-it-yourself maintenance

Do-it-yourself service

precautions

If you perform maintenance
by yourself, be sure to fol-
low the correct procedure
as given in these sections.

Maintenance

Items

Parts and tools

Battery condi-
tion (



P.309)

• Warm water
• Baking soda
• Grease
• Conventional

wrench (for ter-
minal clamp
bolts)

Brake fluid and
Clutch fluid
level (



P.308)

• SAE J1703 or

FMVSS No.116
DOT 3 brake
fluid

• Rag or paper

towel

• Funnel (used

only for adding
brake fluid and
clutch fluid)

Engine cool-
ant
level(



P.307)

• “TOYOTA Genu-

ine 50/50
Pre-mixed Super
Long Life Cool-
ant BLUE” or a
similar high qual-
ity ethylene gly-
col-based
non-silicate,
non-amine,
non-nitrite and
non-borate cool-
ant with long-life
hybrid organic
acid technology.

• For the U.S.A.:

“TOYOTA Genu-
ine 50/50
Pre-mixed Super
Long Life Cool-
ant BLUE” is
pre-mixed with
50% coolant and
50% deionized
water.

• For Canada:

“TOYOTA Genu-
ine 50/50
Pre-mixed Super
Long Life Cool-
ant BLUE” is
pre-mixed with
55% coolant and
45% deionized
water.

• Funnel (used

only for adding
coolant)

Items

Parts and tools

301

6-3. Do-it-yourself maintenance

Maintena

nce
a

nd ca

Engine oil level
(



P.305)

• “Toyota Genuine

Motor Oil” or
equivalent

• Rag or paper

towel

• Funnel (used

only for adding
engine oil)

Fuses
(



P.330)

• Fuse with same

amperage rating
as original

Light bulbs
(



P.333)

• Bulb with same

number and
wattage rating as
original

• Phillips-head

screwdriver

• Flathead screw-

driver

Radiator and
condenser
(



P.308)



Tire inflation
pressure
(



P.323)

• Tire pressure

gauge

• Compressed air

source

Washer fluid
(



P.311)

• Water or washer

fluid containing
antifreeze (for
winter use)

• Funnel (used

only for adding
water or washer
fluid)

Items

Parts and tools

WARNING

The engine compartment contains

many mechanisms and fluids that

may move suddenly, become hot,

or become electrically energized.

To avoid death or serious injury,

observe the following precautions.

■

When working on the engine

compartment

●

Keep hands, clothing and tools

away from the moving fans and

engine drive belt.

●

Be careful not to touch the

engine, radiator, exhaust mani-

fold, etc. right after driving as

they may be hot. Oil and other

fluids may also be hot.

●

Do not leave anything that may

burn easily, such as paper and

rags, in the engine compart-

ment.

●

Do not smoke, cause sparks or

expose an open flame to fuel or

the battery. Fuel and battery

fumes are flammable.

●

Be extremely cautious when

working on the battery. It con-

tains poisonous and corrosive

sulfuric acid.

■

When working near the elec-

tric cooling fans or radiator

grille

Be sure the engine switch is off.
With the engine switch in ON, the

electric cooling fans may auto-

matically start to run if the air con-

ditioning is on and/or the coolant

temperature is high. (



P.308)

■

Safety glasses

Wear safety glasses to prevent

flying or falling material, fluid

spray, etc. from getting in your

eyes.

Toyota 86 (2023 year). Manual in english - page 18