Nissan Versa Note (2019 year). Instruction

The air conditioner system in your NISSAN
vehicle is charged with a refrigerant de-
signed with the environment in mind.
This refrigerant does not harm the
earth’s ozone layer.

Special charging equipment and lubricant
is required when servicing your NISSAN air
conditioner. Using improper refrigerants or
lubricants will cause severe damage to
your air conditioner system. For additional
information, refer to “Air conditioner sys-
tem refrigerant and oil recommendations”
in the “Technical and consumer informa-
tion” section of this manual.

It is recommended that you visit a NISSAN
dealer to service your “environmentally
friendly” air conditioning system.

WARNING

The air conditioner system contains re-
frigerant under high pressure. To avoid
personal injury, any air conditioner ser-
vice should be done only by an experi-
enced

technician

with

proper

equipment.

RADIO

With the ignition placed in the ACC or ON
position, press the PUSH

(power) or

ON•OFF button to turn the radio on. If you
listen to the radio with the engine not run-
ning, the ignition should be placed in the
ACC position.
Radio reception is affected by station sig-
nal strength, distance from radio transmit-
ter, buildings, bridges, mountains and other
external influences. Intermittent changes
in reception quality normally are caused by
these external influences.

Using a cellular phone in or near the ve-
hicle may influence radio reception qual-
ity.

Radio reception

Your NISSAN radio system is equipped with
state-of-the-art electronic circuits to en-
hance radio reception. These circuits are
designed to extend reception range, and to
enhance the quality of that reception.

However, there are some general charac-
teristics of both FM and AM radio signals
that can affect radio reception quality in a
moving vehicle, even when the finest
equipment is used. These characteristics
are completely normal in a given reception

area and do not indicate any malfunction
in your NISSAN radio system.

Reception

conditions

will

constantly

change because of vehicle movement.
Buildings, terrain, signal distance and inter-
ference from other vehicles can work
against ideal reception. Described below
are some of the factors that can affect your
radio reception.

Some cellular phones or other devices may
cause interference or a buzzing noise to
come from the audio system speakers.
Storing the device in a different location
may reduce or eliminate the noise.

FM RADIO RECEPTION

Range: FM range is normally limited to 25 –
30 mi (40 – 48 km), with monaural (single
channel) FM having slightly more range
than stereo FM. External influences may
sometimes interfere with FM station re-
ception even if the FM station is within 25
mi (40 km). The strength of the FM signal is
directly related to the distance between
the transmitter and receiver. FM signals fol-
low a line-of-sight path, exhibiting many of
the same characteristics as light. For ex-
ample, they will reflect off objects.

SERVICING AIR CONDITIONER

AUDIO SYSTEM

Monitor, climate, audio, phone and voice recognition systems

4-23

Fade and drift: As your vehicle moves away
from a station transmitter, the signals will
tend to fade and/or drift.

Static and flutter: During signal interfer-
ence from buildings, large hills or due to
antenna position (usually in conjunction
with increased distance from the station
transmitter), static or flutter can be heard.
This can be reduced by adjusting the treble
control to reduce treble response.

Multipath reception: Because of the reflec-
tive characteristics of FM signals, direct and
reflected signals reach the receiver at the
same time. The signals may cancel each
other, resulting in momentary flutter or loss
of sound.

AM RADIO RECEPTION

AM signals, because of their low frequency,
can bend around objects and skip along
the ground. In addition, the signals can be
bounced off the ionosphere and bent back
to earth. Because of these characteristics,
AM signals are also subject to interference
as they travel from transmitter to receiver.

Fading: Occurs while the vehicle is passing
through freeway underpasses or in areas
with many tall buildings. It can also occur

for several seconds during ionospheric tur-
bulence even in areas where no obstacles
exist.

Static: Caused by thunderstorms, electrical
power lines, electric signs and even traffic
lights.

AUDIO OPERATION PRECAUTIONS

USB (Universal Serial Bus)
connection port

WARNING

Do not connect, disconnect or operate
the USB device while driving. Doing so
can be a distraction. If distracted you
could lose control of your vehicle and
cause an accident or serious injury.

CAUTION

∙ Do not force the USB device into the

USB port. Inserting the USB device
tilted or up-side-down into the port
may damage the port. Make sure that
the USB device is connected correctly
into the USB port.

∙ Do not grab the USB port cover (if so

equipped) when pulling the USB de-
vice out of the port. This could dam-
age the port and the cover.

∙ Do not leave the USB cable in a place

where it can be pulled unintentionally.
Pulling the cable may damage the
port.

The vehicle is not equipped with a USB de-
vice. USB devices should be purchased
separately as necessary.

This system cannot be used to format USB
devices. To format a USB device, use a per-
sonal computer.

In some jurisdictions, the USB device for the
front seats plays only sound without im-
ages for regulatory reasons, even when the
vehicle is parked.

This

system

supports

various

USB

memory devices, USB hard drives and
iPod® players. Some USB devices may not
be supported by this system.

∙ Partitioned USB devices may not play

correctly.

4-24

Monitor, climate, audio, phone and voice recognition systems

∙ Some characters used in other lan-

guages (Chinese, Japanese, etc.) may
not appear properly in the display. Using
English language characters with a USB
device is recommended.

General notes for USB use:

∙ For additional information, refer to your

device manufacturer’s owner informa-
tion regarding the proper use and care
of the device.

Notes for iPod® use:

iPod® is a trademark of Apple Inc., regis-
tered in the U.S. and other countries.

∙ Improperly plugging in the iPod® may

cause a checkmark to be displayed on
and off (flickering). Always make sure
that the iPod® is connected properly.

∙ An iPod® nano (1st Generation) may re-

main in fast forward or rewind mode if it
is connected during a seek operation. In
this case, please manually reset the
iPod®.

∙ An iPod® nano (2nd Generation) will

continue to fast-forward or rewind if it is
disconnected during a seek operation.

∙ An incorrect song title may appear

when the Play Mode is changed while
using an iPod® nano (2nd Generation).

∙ Audiobooks may not play in the same

order as they appear on an iPod®.

∙ Large video files cause slow responses

in an iPod®. The vehicle center display
may momentarily black out, but will
soon recover.

∙ If an iPod® automatically selects large

video files while in the shuffle mode, the
vehicle center display may momen-
tarily black out, but will soon recover.

Bluetooth® streaming audio

∙ Some Bluetooth® audio devices may

not be recognized by the in-vehicle au-
dio system.

∙ It is necessary to set up the wireless

connection

between

compatible

Bluetooth® audio device and the in-
vehicle Bluetooth® module before using
the Bluetooth® audio.

∙ Operating procedure of the Bluetooth®

audio will vary depending on the de-
vices. Make sure how to operate your
audio device before using it with this
system.

∙ The Bluetooth® audio may be stopped

under the following conditions:

∙ Receiving a call on the Bluetooth®

Hands-Free Phone System.

∙ Checking the connection to the

hands-free phone.

∙ Do not place the Bluetooth® audio de-

vice in an area surrounded by metal or
far away from the in-vehicle Bluetooth®
module to prevent tone quality degra-
dation and wireless connection disrup-
tion.

∙ While an audio device is connected

through the Bluetooth® wireless con-
nection, the battery power of the device
may discharge quicker than usual.

∙ This system supports the Bluetooth®

Audio Distribution Profile (A2DP, AVRCP).

BLUETOOTH® is a
trademark owned
by Bluetooth SIG,
Inc. and licensed
to Panasonic.

Monitor, climate, audio, phone and voice recognition systems

4-25

FM/AM RADIO

MENU button

2. AUDIO button

3. Display screen

(SEEK/TRACK) buttons

5. VOL

(volume)

knob

PUSH

(power) button

For additional information, refer to “Audio
operation precautions” regarding all opera-
tion precautions in this section.

Audio main operation

VOL (volume) knob / PUSH
(power) button

Place the ignition switch in the ON position
and press the PUSH

(power) button

while the system is off to call up the mode
(radio, AUX, Bluetooth® audio, USB or iPod®)
that was playing immediately before the
system was turned off.
To

turn

the

system

off,

press

the

PUSH

(power) button.

Turn the VOL (volume) knob to adjust the
volume.

This vehicle may be equipped with Speed
Sensitive Volume. When this feature is ac-
tive, the audio volume changes as the driv-
ing speed changes.

MENU button

Press the

MENU button to show the

Menu screen. Touch the “Settings” key on
the display, then touch the “Sound” key.

LHA4672

4-26

Monitor, climate, audio, phone and voice recognition systems

Sound Settings

Bass

Adjusts the bass to the desired level.

Treble

Adjusts the treble to the desired level.

Balance

Adjusts the balance to the desired level. Balance adjusts the sound level between the left and
right speakers.

Fade

Adjusts the fade to the desired level. Fade adjusts the sound level between the front and rear
speakers.

Speed Sensitive Volume

Adjusts the speed sensitive volume function, which increases the volume of the audio system
as the speed of the vehicle increases. Set to “OFF” to disable the feature. The higher the setting,
the more the volume increases in relation to vehicle speed.

Bass, treble, balance, fade and Speed Sensitive Volume can be adjusted by touching “-”/“+” , “L”/”R”, or “R”/”F” keys.

Monitor, climate, audio, phone and voice recognition systems

4-27

AUDIO button

Push to display the audio screen. When this
button is pushed while the audio screen is
not displayed, the last audio source played
will play.

AM/FM radio screen

1. “AM Menu” / “FM Menu” key

Touch to display the radio menu
screen.

2. Direct Tune

Touch to manually enter a station.

3. Audio source indicator

Indicates the currently selected audio
source.

4. Reception information display

Reception information currently avail-
able such as frequency, station name,
etc. is displayed.

5. Preset list

To listen to a preset station, touch the
corresponding station from the preset
list. If displayed, touch the “<” or “>” keys
to scroll the preset list.

AM radio operation

Press the

MENU button and touch the

“AM” key or press the AUDIO button and
select AM on the bottom of the Launch Bar
to bring up the AM display screen.
If another audio source is playing when the
“AM” key is pressed, the audio source play-
ing will automatically be turned off and the
last radio station played will begin playing.

AM Menu

Touch the “AM Menu” key to display the AM
Menu screen options:

∙ SCAN: To scan tune the stations, touch

the “AM Menu” key on the radio screen
and then touch the “SCAN” key. The sta-
tions will be tuned from low to high fre-
quencies and stop at each broadcast-
ing

station

for

several

seconds.

Touching the “SCAN” key again during
this period of several seconds will stop
tuning and the radio will remain tuned
to that station.

LHA4708

4-28

Monitor, climate, audio, phone and voice recognition systems

∙ Refresh: Touch the “Refresh” key to scan

and update the station list displayed on
the right side of the AM Menu screen.

(SEEK/TRACK) buttons

Press the

buttons to tune

from low to high or high to low frequencies
and to stop at the next broadcasting sta-
tion.
1 to 6 station memory operations

Up to six stations can be registered in the
preset list.

1. Select the AM radio band.

2. Tune to the station you wish to store.

3. Touch and hold one of the preset num-

bers in the preset list.

The information such as frequency will be
displayed on the preset list.

To select and listen to the preset stations,

push

on the steering wheel

briefly or touch a preferred station on the
preset list on the radio screen.

FM radio operation

Press the

MENU button and touch the

“FM” key or press the AUDIO button and
select FM on the bottom of the Launch Bar
to bring up the FM display screen.
If another audio source is playing when the
“FM” key is pressed, the audio source play-
ing will automatically be turned off and the
last radio station played will begin playing.

The FM stereo indicator (STEREO) is shown
on the screen during FM stereo reception.
When the stereo broadcast signal is weak,
the radio automatically changes from ste-
reo to monaural reception.

FM Menu

Touch the “FM Menu” key to display the FM
Menu screen options:

∙ SCAN: To scan tune the stations, touch

the “FM Menu” key on the radio screen
and then touch the “SCAN” key. The sta-
tions will be tuned from low to high fre-
quencies and stop at each broadcast-
ing

stations

for

several

seconds.

Touching the “SCAN” key again during
this period of several seconds will stop
tuning and the radio will remain tuned
to that station.

∙ Refresh: Touch the “Refresh” key to up-

date the station list displayed on the
right side of the FM Menu screen.

∙ RDS Info: Radio station and song infor-

mation can be displayed on the FM dis-
play screen.

(SEEK/TRACK) buttons

Press the

buttons to tune

from low to high or high to low frequencies
and to stop at the next broadcasting sta-
tion.
1 to 12 Station memory operations

Up to 12 stations can be registered in the
preset list.

1. Select the FM radio band.

2. Tune to the station you wish to store.

3. Touch and hold one of the preset num-

bers in the preset list.

The information such as frequency will be
displayed on the preset list.

To select and listen to the preset stations,

push

on the steering wheel

briefly or touch a preferred station on the
preset list on the radio screen.

Monitor, climate, audio, phone and voice recognition systems

4-29

Auxiliary (AUX) devices operation

Connecting auxiliary devices

Connect an AUX device into the AUX input
jack located on the center console below
the heater and air conditioner controls.

The AUX input jack accepts any standard
analog audio input such as from a portable
cassette player, CD player, MP3 player or
phone.

Insert a 1/8 in (3.5 mm) stereo mini plug in
the audio input jack. If a cable with a mono
plug is used, the audio output may not
function normally.

Activation and playing

Turn on the AUX device. Connect an AUX
cable to the AUX device and the AUX input
jack. Select AUX mode from the audio
source menu screen or by pressing the
Source button on the steering wheel.

AUX screen

∙ Audio source indicator

Indicates that the AUX source is cur-
rently playing.

∙ “Volume Setting” keys

Touch one of the keys to select the
sound output gain from Low, Medium
and High.

∙ AUX from Launch Bar

Touch to change from another source
to AUX.

Additional features

For additional information, refer to “iPod®
player operation” in this section.

For additional information, refer to “USB
(Universal Serial Bus) connection port” in
this section.

For

additional

information,

refer

“Bluetooth® streaming audio” in this sec-
tion.

Microsoft (WMA) Obligation of
Labeling

Additional Obligation of Labeling

This product is protected by certain intel-
lectual

property

rights

Microsoft

Corporation and third parties. Use or distri-
bution of such technology outside of this
product is prohibited without a license
from Microsoft or an authorized Microsoft
subsidiary and third parties.

LHA4709

4-30

Monitor, climate, audio, phone and voice recognition systems

USB (Universal Serial Bus)
CONNECTION PORT

Connecting a device to the USB
connection port

WARNING

Do not connect, disconnect, or operate
the USB device while driving. Doing so
can be a distraction. If distracted you
could lose control of your vehicle and
cause an accident or serious injury.

CAUTION

∙ To avoid damage and loss of function

when using a USB device, note the fol-
lowing precautions.

∙ Do not force the USB device into the

USB port. Inserting the USB device
tilted or up-side-down into the port
may damage the port. Make sure that
the USB device is connected correctly
into the USB port.

∙ Do not grab the USB port cover (if so

equipped) when pulling the USB de-
vice out of the port. This could dam-
age the port and the cover.

∙ Do not leave the USB cable in a place

where it can be pulled unintentionally.
Pulling the cable may damage the
port.

For additional information, refer to your de-
vice manufacturer’s owner information re-
garding the proper use and care of the
device.

The USB port is located on the center con-
sole beneath the heater and air condi-
tioner controls. Insert the USB device into
the connection port.

When a compatible storage device is
plugged into the connection port, compat-
ible audio files on the storage device can be
played through the vehicle’s audio system.
The port is illuminated for better visibility
when the headlight switch is in the ON po-
sition.

LHA4458

Monitor, climate, audio, phone and voice recognition systems

4-31

USB connections screen

Press the

MENU button and touch the

“Connections” key or press the “Settings”
key and touch the “Connections” key to
change USB settings.

∙ Auto Change Source

Touch ON or OFF to change the audio
source settings for USB memory de-
vices or an iPod® connected through a
USB cable.

USB screen

1. “USB Menu” key

Touch to switch to the USB Menu
screen.

2. Track information

Track information such as the song
name, artist name and album name
are displayed.

3. Audio source indicator

Indicates the currently selected audio
source.

4. USB operation keys

Touch to control USB playback func-
tions

5. Play time and progress bar

The play time of the track is displayed.
The bar indicates the progress in play-
ing a track.

USB operation keys

Touch to control USB playback functions.

Keys

Description

Each time “

” key is touched, the

repeat mode changes.

Touch to return to the beginning of the
current track. Touch again to select the
previous track. Touch and hold to rewind
the current track.

Touch to play the track.

Touch to pause the track.

Touch to select the next track. Touch
and hold to fast-forward the track.

Each time “

” key is touched, the

random mode changes.

LHA4711

LHA4710

4-32

Monitor, climate, audio, phone and voice recognition systems

USB memory device player
operation

Activation and playing
Connecting the USB memory device into
the port will start playing the USB memory.

USB memory device can also be played by
touching the “USB” key on the Menu screen
or by touching USB on the Launch Bar.

To pause playing the USB memory device
touch the “

” key. To resume playing,

touch the “

” key.

Skipping tracks

To skip the tracks, push the

buttons on the control panel or touch the

“

” or “

” keys on the screen repeat-

edly until the preferred track is selected.

NOTE:

Depending on the condition, skipping to
the previous track may require pushing
the button or touching the key twice.
Pushing the button or touching the key
once may only restart the current track
from the beginning.

Fast-forwarding/rewinding
To rewind or fast-forward the track, push

and hold the

buttons on the

control panel or touch and hold the “

”

or “

” keys on the screen.

Changing play mode
Repeat mode

Touch the “

” key on the USB screen to

change the repeat mode.
The following modes are available:
All: Repeat all

1 Folder: Repeat folder/sub-folder

1 Track: Repeat track

Random mode

Touch the “

” key on the screen to

change the random mode as follows:
No text displayed: Random off

All: Repeat all

1 Folder: Repeat folder/sub-folder

USB menu

Touch the “USB Menu” key on the USB
screen to display the USB Menu screen.

“Now Playing” key

Touch to display the USB
screen.

“Folder List” key

Touch to display the folder
list. Touch an item on the list
to select the folder. The sub-
folder or track list will be
displayed. Select a sub-folder
or track from the list.

“Album Artwork”

Touch to run on/off the al-
bum artwork display on the
USB screen.

Monitor, climate, audio, phone and voice recognition systems

4-33

iPod®* PLAYER OPERATION

Connecting iPod®

WARNING

Do not connect, disconnect, or operate
the USB device while driving. Doing so
can be a distraction. If distracted you
could lose control of your vehicle and
cause an accident or serious injury.

CAUTION

∙ Do not force the USB device into the

USB port. Inserting the USB device
tilted or up-side-down into the port
may damage the port. Make sure that
the USB device is connected correctly
into the USB port.

∙ Do not grab the USB port cover (if so

equipped) when pulling the USB de-
vice out of the port. This could dam-
age the port and the cover.

∙ Do not leave the USB cable in a place

where it can be pulled unintentionally.
Pulling the cable may damage the
port.

For additional information, refer to your de-
vice manufacturer’s owner information re-
garding the proper use and care of the
device.

To connect an iPod® to the vehicle so that
the iPod® can be controlled with the audio
system controls and display screen, use
the USB connection port located on the
center console below the heater and air
conditioner controls. Connect the iPod®-
specific end of the cable to the iPod® and
the USB end of the cable to the USB con-
nection port on the vehicle. If your iPod®

supports charging via a USB connection, its
battery will be charged while connected to
the vehicle with the ignition switch in the
ON position. The port is illuminated for bet-
ter visibility when the headlight switch is in
the ON position.

While connected to the vehicle, the iPod®
can only be operated by the vehicle audio
controls.

To disconnect the iPod® from the vehicle,
remove the USB end of the cable from the
USB connection port on the vehicle, then
remove the cable from the iPod®.

* iPod® is a trademark of Apple Inc., regis-
tered in the U.S. and other countries.

Compatibility

The following models are compatible:

∙ iPod® Classic 5th generation (firmware

version 1.3.0 or later)

∙ iPod® Classic 6th generation (firmware

version 2.0.1 or later)

∙ iPod® Classic 7th generation (firmware

version 2.0.4 or later)

∙ iPod® Shuffle 1st generation

∙ iPod® Shuffle 2nd generation

LHA4358

4-34

Monitor, climate, audio, phone and voice recognition systems

∙ iPod® Shuffle 3rd generation

∙ iPod® Shuffle 4th generation

∙ iPod® Touch 1st generation (firmware

version 4.2.1 or later)*

∙ iPod® Touch 2nd generation (firmware

version 4.2.1 or later)*

∙ iPod® Touch 3rd generation (firmware

version 5.1 or later)

∙ iPod® Touch 4th generation (firmware

version 5.1 or later)

∙ iPod® Touch 5th generation (firmware

version 5.1 or later)

∙ iPod® Touch 6th generation (firmware

version 5.1 or later)

∙ iPod® nano - 1st generation (firmware

version 1.3.1 or later)

∙ iPod® nano - 2nd generation (firmware

version 1.1.3 or later)

∙ iPod® nano - 3rd generation (firmware

version 1.1.3 or later)

∙ iPod® nano - 4th generation (firmware

version 1.0.4 or later)

∙ iPod® nano - 5th generation (firmware

version 1.0.2 or later)

∙ iPod® nano - 6th generation (firmware

version 1.1 or later)

∙ iPod® nano - 7th generation (firmware

version 1.1 or later)

∙ iPhone® 3G (firmware version 4.2.1 or

later)

∙ iPhone® 3GS (firmware version 5.1 or

later)

∙ iPhone® 4 (firmware version 5.1 or later)

∙ iPhone® 5 (firmware version 5.1 or later)

∙ iPhone® 5C (firmware version 5.1 or later)

∙ iPhone® 5S (firmware version 5.1 or later)

∙ iPhone® 6 (firmware version 5.1 or later)

∙ iPhone® 6 Plus (firmware version 5.1 or

later)

∙ iPhone® 6S (firmware version 5.1 or later)

∙ iPhone® 6S Plus (firmware version 5.1 or

later)

∙ iPhone® SE (firmware version 5.1 or later)

∙ iPhone® 7 (firmware version 5.1 or later)

∙ iPhone® 7 Plus (firmware version 5.1 or

later)

∙ iPhone® 8 (firmware version 5.1 or later)

∙ iPhone® 8 Plus (firmware version 5.1 or

later)

∙ iPhone® X (firmware version 5.1 or later)

∙ iPad® 2

∙ iPad® 3rd generation

∙ iPad® 4th generation

∙ iPad® 5th generation

∙ iPad® Mini

∙ iPad® Mini 2

∙ iPad® Mini 3

∙ iPad® Mini 4

∙ iPad® Air

∙ iPad® Air 2

∙ iPad® Pro (9.7 inch)

∙ iPad® Pro (10.5 inch)

∙ iPad® Pro (12.9 inch)

∙ iPad® Pro (12.9 inch) 2nd generation

* Some features of this iPod® may not be
fully functional.

Make sure that your iPod® firmware is up-
dated to the version indicated above.

Monitor, climate, audio, phone and voice recognition systems

4-35

iPod screen

1. “iPod Menu” key

Touch to switch to the iPod Menu
screen.

2. Track information

Track information such as the song
name, artist name and album name
are displayed.

3. Audio source indicator

Indicates the currently selected audio
source.

4. Album artwork

An image of the album artwork is dis-
played when available if the setting is
turned on.

5. iPod® operation keys

Touch to control iPod® playback func-
tions

6. Play time and progress bar

The play time of the track is displayed.
The bar indicates the progress in play-
ing a track.

iPod® operation keys

Touch to control iPod® playback functions.

Keys

Description

Each time “

” key is touched, the

repeat mode changes.

Touch to return to the beginning of the
current track. Touch again to select the
previous track. Touch and hold to rewind
the current track.

Touch to play the track.

Touch to pause the track.

Touch to select the next track. Touch
and hold to fast-forward the track.

Each time “

” key is touched, the

random mode changes.

iPod® memory device player
operation

Activation and playing
Connecting the iPod® to the vehicle via USB
cable will activate the iPod® mode.

The iPod® can also be played by touching
the “iPod” key on the Menu screen or by
touching iPod on the Launch Bar.

Skipping tracks

To skip the tracks, push the

buttons on the control panel or touch the

“

” or “

” keys on the screen repeat-

edly until the preferred track is selected.

NOTE:

Fast-forwarding/rewinding
To rewind or fast-forward the track, push

and hold the

buttons on the

control panel or touch and hold the “

”

or “

” keys on the screen,

LHA4724

4-36

Monitor, climate, audio, phone and voice recognition systems

Changing play mode

Repeat mode

Touch the “

” key on the iPod® screen

to change the repeat mode. The following
modes are available.
No text displayed: Repeat off

All: Repeat all

One: Repeat track

Random mode

Touch the “

” key on the screen to

change the random mode as follows.
No text displayed: Random off

Songs: Random play

iPod® Menu

Touch the “iPod Menu” key on the iPod®
screen to display the iPod® Menu screen.

“Now Playing” key

Touch to display the USB
screen.

“Folder List” key
(if so equipped)

Touch to display the folder
list. Touch an item on the list
to select the folder. The sub-
folder or track list will be
displayed. Select a sub-folder
or track from the list.

“Album Artwork”
key

Touch to run on/off the al-
bum artwork display on the
USB screen.

“Playlists” key

Touch to display the list ac-
cording to the selected item.

“Artists” key

“Albums” key

“Songs” key

“Podcasts” key

“Genres” key

“Composers” key

“Audiobooks” key

“iTunes Radio”
key

BLUETOOTH® STREAMING AUDIO

If you have a compatible Bluetooth® audio
device that is capable of playing audio files,
the device can be connected to the vehi-
cle’s audio system so that the audio files on
the device play through the vehicle’s
speakers. For additional information, refer
to “FM/AM radio” in this section.

NOTE:

For additional information, refer to the
cellular phone Owner’s Manual.

Monitor, climate, audio, phone and voice recognition systems

4-37

Nissan Versa Note (2019 year). Instruction - part 12