Nissan Versa Note (2019 year). Instruction - part 9

∙ Vehicles not equipped with Intelligent

Key (if so equipped)

– All doors unlock automatically when

the transmission is placed in the P
(Park) position (if so equipped), the
ignition is turned to the OFF position
or when the key is removed from the
ignition.

CHILD SAFETY REAR DOOR LOCK

Child safety locks help prevent the rear
doors from being opened accidentally, es-
pecially when small children are in the ve-
hicle.

The child safety lock levers are located on
the edge of the rear doors.

When the lever is in the unlock position

䊊

the door can be opened from the outside
or the inside.

When the lever is in the LOCK position

䊊

the door can be opened only from the
outside.

WARNING

∙ Radio waves could adversely affect

electric medical equipment. Those
who use a pacemaker should contact
the

electric

medical

equipment

manufacturer for the possible influ-
ences before use.

∙ The remote keyless entry key fob

transmits radio waves when the but-
tons are pressed. The FAA advises ra-
dio waves may affect aircraft naviga-
tion and communication systems. Do
not operate the remote keyless entry
key fob while on an airplane. Make
sure the buttons are not operated un-
intentionally when the unit is stored
for a flight.

It is possible to lock/unlock all doors, turn
the interior lights on, and activate the panic
alarm by using the key fob from outside the
vehicle.

Be sure to remove the key from the ve-
hicle before locking the doors.

The key fob can operate at a distance of
approximately 33 ft (10 m) from the vehicle.
The effective distance depends on the
conditions around the vehicle.

LPD2166

REMOTE KEYLESS ENTRY SYSTEM
(models without NISSAN Intelligent
Key®) (if so equipped)

3-8

Pre-driving checks and adjustments

As many as five key fobs can be used with
one vehicle. For information concerning
the purchase and use of additional key
fobs, it is recommended that you visit a
NISSAN dealer.

The key fob will not function when:

∙ The battery is discharged.

∙ The distance between the vehicle and

the key fob is over 33 ft (10 m).

The panic alarm will not activate when
the key is in the ignition switch.

CAUTION

Listed below are conditions or occur-
rences which will damage the key fob:

∙ Do not allow the key fob, which con-

tains electrical components, to come
into contact with water or salt water.
This could affect the system function.

∙ Do not drop the key fob.

∙ Do not strike the key fob sharply

against another object.

∙ Do not change or modify the key fob.

∙ Wetting may damage the key fob. If

the key fob gets wet, immediately
wipe until it is completely dry.

∙ Do not place the key fob for an ex-

tended period in an area where tem-
peratures exceed 140°F (60°C).

∙ Do not attach the key fob with a key

holder that contains a magnet.

∙ Do not place the key fob near equip-

ment that produces a magnetic field,
such as a TV, audio equipment and
personal computers.

If a key fob is lost or stolen, NISSAN rec-
ommends erasing the ID code of that
key fob. This will prevent the key fob
from unauthorized use to unlock the
vehicle. For information regarding the
erasing procedure, it is recommended
that you visit a NISSAN dealer.

HOW TO USE REMOTE KEYLESS
ENTRY SYSTEM

Locking doors

1. Close all windows.

2. Remove the key from the ignition

switch.

3. Close all doors and the rear hatch.

LPD2039

Pre-driving checks and adjustments

3-9

4. Press the

button on the key fob.

All the doors lock. The hazard warning
lights flash twice and the horn beeps
once to indicate all doors are locked.

∙ When the

button is pressed

with all doors locked, the hazard
warning lights flash twice and the
horn beeps once as a reminder that
the doors are already locked.

∙ If a door is open and you press

the

button, the doors will lock

but the horn will not beep and the
hazard lights will not flash.

The horn may or may not beep. For addi-
tional information, refer to “Silencing the
horn beep feature” in this section.

Unlocking doors

Press the

button on the key fob once.

∙ Only the driver’s door unlocks.

∙ The hazard warning lights flash once if

all doors are completely closed with the
ignition switch in any position except
the ON position.

∙ The interior light turns on and the light

timer activates for a period of time
when the interior light switch is in the
DOOR position with the ignition switch
in any position except the ON position.

Press the

button on the key fob again

within 5 seconds.

∙ All doors and the rear hatch unlock.

∙ The hazard warning lights flash once if

all doors are completely closed.

The interior lights can be turned off without
waiting by inserting the key into the ignition
switch and placing the ignition in the ON or
START (if so equipped) position, locking the
doors with the key fob or pushing the inte-
rior light switch to the OFF position.

Auto relock

When the

button on the key fob is

pressed, all doors will lock automatically
within 1 minute unless one of the following
operations is performed:

∙ Any door is opened.

∙ The ignition is placed in the ON or START

(if so equipped) position.

LPD2040

3-10

Pre-driving checks and adjustments

Using the panic alarm

If you are near your vehicle and feel threat-
ened, you may activate the panic alarm to
call attention by pressing and holding
the

button on the key fob for longer

than 0.5 seconds.
The panic alarm and headlights will stay on
for a period of time.

The panic alarm stops when:

∙ It has run for a period of time.

∙ Any button is pressed on the key fob.

Using the interior light (if so
equipped)

Press the

button on the key fob once

to turn on the interior lights.
For additional information, refer to “Interior
lights” in the “Instruments and controls”
section of this manual.

Silencing the horn beep feature

If desired, the horn beep feature can be
deactivated using the key fob.

To deactivate: Press and hold the
and

buttons for at least 2 seconds.

The hazard warning lights will flash three
times to confirm that the horn beep fea-
ture has been deactivated.

To activate: Press and hold the
and

buttons for at least 2 seconds

once more.

LPD2041

LPD2044

Pre-driving checks and adjustments

3-11

The hazard warning lights will flash once
and the horn will sound once to confirm
that the horn beep feature has been reac-
tivated.

Deactivating the horn beep feature does
not silence the horn if the alarm is trig-
gered.

WARNING

∙ Radio waves could adversely affect

electric medical equipment. Those
who use a pacemaker should contact
the

electric

medical

equipment

manufacturer for the possible influ-
ences before use.

∙ The Intelligent Key transmits radio

waves when the buttons are pressed.
The FAA advises the radio waves may
affect aircraft navigation and com-
munication systems. Do not operate
the Intelligent Key while on an air-
plane. Make sure the buttons are not
operated unintentionally when the
unit is stored for a flight.

The Intelligent Key can operate all the door
locks using the remote control function or
pushing the request switch on the vehicle
without taking the key out from a pocket or
purse. The operating environment and/or
conditions may affect the Intelligent Key
operation.

Be sure to read the following before using
the Intelligent Key.

CAUTION

∙ Be sure to carry the Intelligent Key

with you when operating the vehicle.

∙ Never leave the Intelligent Key in the

vehicle when you leave the vehicle.

The Intelligent Key is always communicat-
ing with the vehicle as it receives radio
waves. The Intelligent Key transmits weak
radio waves. Environmental conditions
may interfere with the operation of the In-
telligent Key under the following operating
conditions:

∙ When operating near a location where

strong radio waves are transmitted,
such as a TV tower, power station and
broadcasting station.

∙ When in possession of wireless equip-

ment, such as a cellular telephone,
transceiver, or a CB radio.

∙ When the Intelligent Key is in contact

with or covered by metallic materials.

∙ When any type of radio wave remote

control is used nearby.

∙ When the Intelligent Key is placed near

an electric appliance such as a personal
computer.

NISSAN INTELLIGENT KEY® (if so
equipped)

3-12

Pre-driving checks and adjustments

∙ When the vehicle is parked near a park-

ing meter.

In such cases, correct the operating condi-
tions before using the Intelligent Key func-
tion or use the mechanical key.

Although the life of the battery varies de-
pending on the operating conditions, the
battery’s life is approximately two years. If
the battery is discharged, replace it with a
new one.

When the Intelligent Key battery is low, the
Intelligent Key system warning light (

)

will blink green for about 30 seconds after
the ignition switch is placed in the ON po-
sition.
Since the Intelligent Key is continuously re-
ceiving radio waves, if the key is left near
equipment which transmits strong radio
waves, such as signals from a TV and per-
sonal computer, the battery life may be-
come shorter.

When the battery is discharged, firmly ap-
ply the foot brake and touch the ignition
switch with the Intelligent Key. Then push
the ignition switch while depressing the
brake pedal within 10 seconds after the
chime sound. For additional information,

refer to “Push-button ignition switch” in the
“Starting

and

driving”

section

this

manual.

For additional information, refer to “Battery
replacement” in the “Do-it-yourself ” section
of this manual.

As many as four Intelligent Keys can be
registered and used with one vehicle. For
information about the purchase and use of
additional Intelligent Keys, it is recom-
mended that you visit a NISSAN dealer.

CAUTION

Listed below are conditions or occur-
rences which will damage the Intelli-
gent Key:

∙ Do not allow the Intelligent Key, which

contains electrical components, to
come into contact with water or salt
water. This could affect the system
function.

∙ Do not drop the Intelligent Key.

∙ Do not strike the Intelligent Key

sharply against another object.

∙ Do not change or modify the Intelli-

gent Key.

∙ Wetting may damage the Intelligent

Key. If the Intelligent Key gets wet, im-
mediately wipe until it is completely
dry.

∙ If the outside temperature is below

14°F (-10°C) the battery of the Intelli-
gent Key may not function properly.

∙ Do not place the Intelligent Key for an

extended period in an area where
temperatures exceed 140°F (60°C).

∙ Do not attach the Intelligent Key with

a key holder that contains a magnet.

∙ Do not place the Intelligent Key near

equipment that produces a magnetic
field, such as a TV, audio equipment
and personal computers.

If an Intelligent Key is lost or stolen, NISSAN
recommends erasing the ID code of that
Intelligent Key from the vehicle. This may
prevent the unauthorized use of the Intelli-
gent Key to operate the vehicle. For infor-
mation regarding the erasing procedure, it
is recommended that you visit a NISSAN
dealer.

Pre-driving checks and adjustments

3-13

OPERATING RANGE

The Intelligent Key functions can only be
used when the Intelligent Key is within the
specified operating range from the request
switch

䊊

When the Intelligent Key battery is dis-
charged or strong radio waves are present
near the operating location, the Intelligent
Key operating range becomes narrower,
and the Intelligent Key may not function
properly.

The operating range is within 31.50 in
(80 cm) from each request switch

䊊

If the Intelligent Key is too close to the door
glass, handle or rear bumper, the request
switches may not function.

When the Intelligent Key is within the oper-
ating range, it is possible for anyone, even
someone who does not carry the Intelli-
gent Key, to push the request switch to
lock/unlock the doors.

DOOR LOCKS/UNLOCKS
PRECAUTION

∙ Do not push the door handle request

switch with the Intelligent Key held in
your hand as illustrated. The close dis-
tance to the door handle will cause the
Intelligent Key system to have difficulty
recognizing that the Intelligent Key is
outside the vehicle.

∙ After locking with the door handle re-

quest switch, verify the doors are se-
curely locked by testing them.

LPD2162

LPD2554

3-14

Pre-driving checks and adjustments

∙ To prevent the Intelligent Key from be-

ing left inside the vehicle, make sure you
carry the Intelligent Key with you and
then lock the doors.

∙ Do not pull the door handle before

pushing

the

door

handle

request

switch. The door will be unlocked but
will not open. Release the door handle
once and pull it again to open the door.

NISSAN INTELLIGENT KEY®
OPERATION

You can lock or unlock the doors without
taking the key out of your pocket or bag.

When you carry the Intelligent Key with you,
you can lock or unlock all doors by pushing
the door handle request switch or rear
hatch request switch within the range of
operation.

Locking doors

1. Place the ignition switch to the LOCK

position.

2. Close all doors and the rear hatch.

3. Push any door handle request switch

䊊

or the rear hatch request switch

䊊

while carrying the Intelligent Key with
you.

4. All doors and the rear hatch will lock.

5. The hazard warning lights flash twice

and the horn beeps once.

LPD2913

LPD2914

Pre-driving checks and adjustments

3-15

NOTE:

∙ Doors lock with the door handle re-

quest switch or rear hatch request
switch while the ignition switch is
pushed in.

∙ Doors lock with the door handle re-

quest switch or the rear hatch re-
quest switch while the ignition switch
is not in the LOCK position.

∙ Doors do not lock with the door

handle request switch or the rear
hatch request switch with the Intelli-
gent Key inside the vehicle and a
beep sounds to warn you. However,
when an Intelligent Key is inside the
vehicle, doors can be locked with an-
other Intelligent Key.

CAUTION

∙ After locking the doors using the re-

quest switch, make sure that the
doors have been securely locked by
operating the door handles or the rear
hatch opener switch.

∙ When locking the doors using the re-

quest switch, make sure to have the
Intelligent Key in your possession be-
fore operating the request switch to
prevent the Intelligent Key from being
left in the vehicle.

∙ The request switch is operational only

when the Intelligent Key has been de-
tected by the Intelligent Key system.

Lockout protection

To prevent the Intelligent Key from being
accidentally locked inside the vehicle, lock-
out protection is equipped with the Intelli-
gent Key.

When the driver’s side door is open, the
doors are locked, and then the Intelligent
Key is put inside the vehicle and all the
doors are closed; the lock will automati-
cally unlock and the door chime sounds.

LPD2165

LPD2167

3-16

Pre-driving checks and adjustments

NOTE:

The doors may not lock when the Intelli-
gent Key is in the same hand that is op-
erating the request switch to lock the
door. Put the Intelligent Key in a purse,
pocket or your other hand.

CAUTION

The lockout protection may not func-
tion under the following conditions:

∙ When the Intelligent Key is placed on

top of the instrument panel.

∙ When the Intelligent Key is placed on

top of the rear parcel shelf.

∙ When the Intelligent Key is placed on

the cargo cover.

∙ When the Intelligent Key is placed in-

side the glove box or a storage bin.

∙ When the Intelligent Key is placed in-

side the door pockets.

∙ When the Intelligent Key is placed on

or under the spare tire area.

∙ When the Intelligent Key is placed in-

side or near metallic materials.

Unlocking doors

1. Carry the Intelligent Key.

2. Push the door handle request switch

䊊

or the rear hatch request switch

䊊

3. The hazard warning lights flash once

and the horn beeps once.

4. Push the door handle request switch

䊊

again within 1 minute to unlock all

doors and the rear hatch.

If a door handle is pulled while unlocking
the doors, that door may not be unlocked.
Returning the door handle to its original
position will unlock the door. If the door
does not unlock after returning the door
handle, push the door handle request
switch to unlock the door.

LPD2914

LPD2165

Pre-driving checks and adjustments

3-17

All doors and the rear hatch will be locked
automatically unless one of the following
operations is performed within 1 minute
after pushing the request switch.

∙ Opening any doors or the rear hatch.

∙ Engaging the ignition switch from the

locked position.

The interior light illuminates for a period of
time when a door is unlocked and the
room light switch is in the DOOR position.

The interior light can be turned off without
waiting by performing one of the following
operations.

∙ Placing the ignition switch to the ON

position.

∙ Locking the doors with the remote con-

trol.

∙ Switching the room light switch to the

OFF position.

HOW TO USE THE REMOTE
KEYLESS ENTRY FUNCTION

The remote keyless entry function can op-
erate all door locks using the remote key-
less function of the Intelligent Key. The re-
mote keyless function can operate at a
distance of 33 ft (10 m) away from the ve-
hicle. The operating distance depends
upon the conditions around the vehicle.

The remote keyless entry function may not
function under the following conditions:

∙ When the Intelligent Key is not within the

operational range.

∙ When the doors or the rear hatch are

open or not closed securely.

∙ When the Intelligent Key battery is low

or discharged.

CAUTION

When locking the doors using the Intel-
ligent Key, be sure not to leave the key in
the vehicle.

LPD2167

3-18

Pre-driving checks and adjustments

Locking doors

1. Place the ignition switch in the LOCK

position.

2. Close all doors and the rear hatch.

3. Press the

button on the Intelli-

gent Key.

4. The hazard warning lights flash twice

and the horn beeps once.

5. All doors and the rear hatch will be

locked.

CAUTION

After locking the doors using the Intel-
ligent Key, be sure that the doors have
been securely locked by operating the
door handles.

Unlocking doors

1. Press the

button on the Intelligent

Key.

2. The hazard warning lights flash once.

3. Press the

button again within

1 minute to unlock all doors and the
rear hatch.

WPD0359

WPD0360

Pre-driving checks and adjustments

3-19

All doors and the rear hatch will be locked
automatically unless one of the following
operations is performed within 1 minute
after pressing the

button.

∙ Opening any doors or the rear hatch.

∙ Engaging the ignition switch from the

lock position.

The interior light illuminates for a period of
time when a door is unlocked and the
room light switch is in the DOOR position.

The light can be turned off without waiting
by performing one of the following opera-
tions.

∙ Placing the ignition switch in the ACC or

ON position.

∙ Locking the doors with the remote con-

trol.

∙ Switching the room light switch in the

OFF position.

Using the panic alarm

If you are near your vehicle and feel threat-
ened, you may activate the panic alarm to
call attention by pressing and holding
the

button on the Intelligent Key for

longer than 0.5 seconds.
The panic alarm and headlights will stay on
for a period of time.

The panic alarm stops when:

∙ It has run for a period of time, or

∙ Any button is pressed on the Intelligent

Key.

∙ The request switch on the driver or pas-

senger door or rear hatch has been
pushed and the Intelligent Key is in
range of the door handle.

WPD0374

3-20

Pre-driving checks and adjustments

Silencing the horn beep feature

If desired, the horn beep feature can be
deactivated using the Intelligent Key.

To deactivate: Press and hold the
and

buttons for at least 2 seconds.

The hazard warning lights will flash three
times to confirm that the horn beep fea-
ture has been deactivated.

To activate: Press and hold the
and

buttons for at least 2 seconds

once more.

The hazard warning lights will flash once
and the horn will sound once to confirm
that the horn beep feature has been reac-
tivated.

Deactivating the horn beep feature does
not silence the horn if the alarm is trig-
gered.

䊊

P (Park) position selecting warning
light (if so equipped)

䊊

NISSAN Intelligent Key® warning
light

WARNING LIGHTS AND AUDIBLE
REMINDERS

The Intelligent Key is equipped with a func-
tion that is designed to minimize improper
operations and to help prevent the vehicle
from being stolen. The warning chime
sounds and the warning light illuminates
when improper operations are detected.

WPD0362

Type A (if so equipped)

LPD2094

Pre-driving checks and adjustments

3-21

䊊

P (Park) position selecting warning
light (if so equipped)

䊊

NISSAN Intelligent Key® warning
light

CAUTION

When the buzzer sounds and the warn-
ing light illuminates, be sure to check
both the vehicle and the Intelligent Key.

WARNING SIGNALS

To help prevent the vehicle from moving
unexpectedly by erroneous operation of
the Intelligent Key or to help prevent the
vehicle from being stolen, a chime or
buzzer sounds from inside and outside the
vehicle and a warning is displayed in the
instrument panel.

When a chime or beep sounds or a warning
is displayed, be sure to check the vehicle
and the Intelligent Key.

For additional information, refer to the
“Troubleshooting guide” in this section and
“Warning lights, indicator lights and audible
reminders” in the “Instruments and con-
trols” section of this manual.

Audible reminder and warning
when locking the doors

When the chime or buzzer sounds from
inside and outside the vehicle, check for
the following:

∙ The ignition switch is placed in the LOCK

position.

∙ The Intelligent Key is not left inside the

vehicle.

∙ The shift lever is in the P (Park) (Continu-

ously Variable Transmission models) or
N (Neutral) (manual transmission mod-
els) position with the parking brake fully
applied.

Audible reminder and warning
when the engine stops

When the P (Park) position selecting warn-
ing light (

) (if so equipped) in the in-

strument panel illuminates red:

∙ Make sure the shift lever is in the P (Park)

(Continuously

Variable

Transmission

models) or N (Neutral) (manual trans-
mission models) position with the park-
ing brake fully applied.

When the chime sounds intermittently:

∙ Make sure the shift lever is in the P (Park)

(Continuously

Variable

Transmission

models) or N (Neutral) (manual trans-
mission models) position with the park-
ing brake fully applied and the ignition
switch is placed in the LOCK position.

Type B (if so equipped)

LPD2219

3-22

Pre-driving checks and adjustments

If the chime sounds continuously when the
driver’s door is opened, check the following:

∙ The shift lever is placed in the P (Park)

(Continuously

Variable

Transmission

models) or N (Neutral) (manual trans-
mission models) position with the park-
ing brake fully applied and the ignition
switch is placed in the LOCK position.

∙ The warning chime may stop when one

of the following is performed:

– Returning the ignition switch to the

LOCK position.

– Closing the doors.

Alarm and warning when the
engine starts

When the Intelligent Key system warning
light (

) is yellow and the outside

buzzer sounds, make sure the Intelligent
Key is inside the vehicle.

Warning for low battery power

When the Intelligent Key battery is low, the
Intelligent Key system warning light (

)

will blink green for about 30 seconds after
the ignition switch is placed in the ON po-
sition. This warning is to let you know that
the battery of the Intelligent Key will run
down soon. Replace it with a new one. For
additional information, refer to “Battery re-
placement” in the “Do-it-yourself ” section
of this manual.
It is recommended that you visit a NISSAN
dealer for battery replacement.

Preventing the Intelligent Key
from being left in the vehicle

If you lock all doors using the power door
lock switch with the Intelligent Key in the
vehicle, all of the doors unlock immediately
and the buzzer will warn you when the door
is closed.

Pre-driving checks and adjustments

3-23

Content .. 7 8 9 10 ..