Nissan 370Z Roadster (2017 year). Instruction

(242,1)

[ Edit: 2016/ 2/ 22

Model: 2017MY NISSAN 370Z(Z34) OM17E00Z34U0 ]

4-78

Center display, heater, air conditioner, audio, phone and voice recognition systems

SAA2518

CONTROL BUTTONS

PHONE button

TALK

/PHONE SEND

button

JVH0473X

CONNECTING PROCEDURE

1. Push the PHONE button or the

button,

and select the “Connect Phone” key.

SAA2520

2. A message screen is displayed. Operate the

cellular phone according to the message,
and then wait until “MY-CAR” is displayed
on the cellular phone. After selecting “MY-
CAR” on your cellular phone, perform one of
the following procedures.

Input the PIN code displayed on the

screen.

Check that the PIN code displayed on the

screen is the same as the number
displayed on the cellular phone, and then
select [Yes].

For phones that support Simple Secure
Pairing (SSP), check that the PIN code
on the vehicle displayed matches the PIN
code displayed on the phone.

Condition:

(243,1)

[ Edit: 2016/ 2/ 22

Model: 2017MY NISSAN 370Z(Z34) OM17E00Z34U0 ]

The connecting procedure of the cellular
phone varies according to each cellular
phone. See the cellular phone Owner’s
Manual for the details. You can also visit

www.nissanusa.com/bluetooth or call
NISSAN Consumer Affairs Department for
instructions on pairing NISSAN recom-
mended cellular phones.

When the connection process is completed,
the screen will return to the Phone menu
display.

PHONE SELECTION

Up to 5 cellular phones can be registered to the
system. To switch to connect another cellular
phone, push PHONE button and select the
“Connected Phones” key. The registered cellular
phones are shown on the list. If you select a
cellular phone that is different from the one
currently connected, the newly selected phone
will be connected to the system.

QUICK DIAL

This vehicle has two phonebooks available for
hands-free use. Depending on the phone, the
system may automatically download the entire
cell phone’s phonebook into the “ Phonebook”.
For the details about downloading a phonebook,
see “Phone setting” (P.4-84). If a phonebook
does not automatically download, the Quick Dial

may be set for up to 1.000 entries. This Quick
Dial allows the recording of a name to speak
while using voice recognition.

JVH0474X

1. Push the PHONE button and select the

“Quick Dial” key.

2. Select the “Add New” key at the top of the

screen.

Center display, heater, air conditioner, audio, phone and voice recognition systems

4-79

Condition:

(244,1)

[ Edit: 2016/ 2/ 22

Model: 2017MY NISSAN 370Z(Z34) OM17E00Z34U0 ]

4-80

Center display, heater, air conditioner, audio, phone and voice recognition systems

JVH0475X

3. Choose the method for entering the Quick

Dial entry. For this example, select “Enter
Number by Keypad”.

4. Input the name and phone number manually

using the keypad displayed on the screen.
(See “How to use touch screen” (P.4-5).)

JVH0476X

5. Select the “Voicetag” key to record a name

to speak when using the NISSAN Voice
Recognition system.

6. Select the “Store” key and prepare to speak

the name after the tone.

7. When the voicetag is successfully saved,

select the “OK” key to save the Quick Dial
entry.

8. After the Quick Dial entry is saved, it will

show a screen that is ready to call the
number. Push the BACK button to return to
the Quick Dial.

There are different methods to input a phone
number. Select one of the following options

instead of “Enter Number by Keypad” in step 3.

Copy from Call History

The system will show a list of incoming,
outgoing or missed calls that were down-
loaded from the connected cellular phone
(depending on the phone’s compatibility).
Select one of these entries to save in the
Quick Dial.

Copy from the Handset

The system will show the connected cellular
phone’s phonebook that was downloaded
(depending on the phone’s compatibility).
Select one of these entries to save in the
Quick Dial.

Condition:

(245,1)

[ Edit: 2016/ 2/ 22

Model: 2017MY NISSAN 370Z(Z34) OM17E00Z34U0 ]

JVH0477X

Editing the Quick Dial

1. Push the PHONE button and select the

“Quick Dial” key.

2. Select the desired entry from the displayed

list.

3. Select the “Edit” key.

4. Select the desired item to change.

JVH0478X

The following editing items are available:

Entry #

Changes the displayed number of the
selected entry.

Name

Edit the name of the entry using the keypad
displayed on the screen.

Number

Edit the phone number using the keypad
displayed on the screen.

Type

Select an icon from the icon list.

Voicetag

Confirm and store the voicetag. Voicetags

allow easy dialing using the NISSAN Voice
Recognition system. (See “NISSAN Voice
Recognition System (models with navigation
system)” (P.4-99).)

To delete an entry, select the “Delete” key at
step 3.

Center display, heater, air conditioner, audio, phone and voice recognition systems

4-81

Condition:

(246,1)

[ Edit: 2016/ 2/ 22

Model: 2017MY NISSAN 370Z(Z34) OM17E00Z34U0 ]

4-82

Center display, heater, air conditioner, audio, phone and voice recognition systems

JVH0479X

MAKING A CALL

To make a call, follow this procedure.

1. Push the PHONE button on the instrument

panel or the

button on the steering

wheel. The “PHONE” screen will appear on
the display.

2. Select the “Phonebook” key on the

“PHONE” menu.

3. Select the desired entry from the list.

4. Confirm the correct entry by selecting for the

correct number from the list.

JVH0495X

There are different methods to make a call.
Select one of the following options instead of
“Phonebook” in step 2 above.

Quick Dial

Select an entry stored in the Quick Dial.

Call History

Select an outgoing, incoming or missed call
downloaded from your cell phone (depend-
ing on your phone’s compatibility).

Dial Number

Input the phone number manually using the
keypad displayed on the screen. (See “How
to use touch screen” (P.4-5).)

SAA2525

RECEIVING A CALL

When you hear a phone ring, the display will
change to the incoming call mode. To receive a
call, perform one of the following procedures
listed below.

1. Select the “Answer” key.

2. Push the PHONE button on the instrument

panel.

3. Push the

button on the steering wheel.

There are some options available when receiving
a call. Select one of the following displayed on
the screen.

Answer

Accept an incoming call to talk.

Condition:

(247,1)

[ Edit: 2016/ 2/ 22

Model: 2017MY NISSAN 370Z(Z34) OM17E00Z34U0 ]

Hold Call

Put an incoming call on hold.

Reject Call

Reject an incoming call.

To finish the call, perform one of the
following procedures listed below.

1. Select the “Hang up” key.

2. Push the PHONE button on the instrument

panel.

3. Push the

button on the steering wheel.

SAA3587

DURING A CALL

There are some options available during a call.
Select one of the following displayed on the
screen if necessary.

Hang up

Finish the call.

Use Handset

Transfer the call to the cellular phone.

Mute

Mute your voice to the person.

Keypad

Using the touch tone, send digits to the
connected party for using services such as
voicemail.

Cancel Mute

This will appear after “Mute” is selected.
Mute will be canceled.

Switch Call*

Select “Switch Call” to answer another
incoming call. By selecting “Hang up”, you
can end a call and can speak to a caller who
is on hold again.

* This function may not be usable, depend-
ing on the model of phone.

To adjust the person’s voice to be louder or
quieter, push the volume control switch (+ or

−)

on the steering wheel or turn the volume control
knob on the instrument panel while talking on
the phone. This adjustment is also available in
the SETTING mode.

Center display, heater, air conditioner, audio, phone and voice recognition systems

4-83

Condition:

(248,1)

[ Edit: 2016/ 2/ 22

Model: 2017MY NISSAN 370Z(Z34) OM17E00Z34U0 ]

4-84

Center display, heater, air conditioner, audio, phone and voice recognition systems

JVH0480X

PHONE SETTING

To set up the Bluetooth

Hands-Free Phone

System to your preferred settings, push the
SETTING button on the instrument panel and
select the “PHONE” key.

Edit Quick DIal

To edit the Quick Dial, use the same procedure
as described in “Quick Dial” (P.4-79).

Delete Quick Dial

The Quick Dial entries can be deleted all at the
same time or one by one.

Download Phonebook

Download the contacts registered in a Blue-
tooth

cellular phone. Availability of this function

depends on each cellular phone. The memory
downloading procedure from the cellular phone
also varies according to each cellular phone.
See cellular phone Owner’s Manual for details.

Volume & Ringtone

The following kinds of phone volume can be set.
Pushing the PHONE button and selecting the
“Volume & Ringtone” key can also operate the
same settings.

Ringtone/Incoming Call/Outgoing Call

To increase or decrease the volume, select
the “Ringtone”, “Incoming Call” or “Out-
going Call” key and adjust it with the multi-
function controller.

Automatic Hold

When this function is activated, an incoming
phone call is automatically held.

Vehicle Ringtone

When this function is activated, a specific
ringtone that is different from the cellular
phone will sound when receiving a call.

Auto Downloaded

When this item is activated, the phonebook of a
hands-free phone is automatically downloaded
at the same time that the hands-free phone is
connected.

Condition:

(249,1)

[ Edit: 2016/ 2/ 22

Model: 2017MY NISSAN 370Z(Z34) OM17E00Z34U0 ]

TROUBLESHOOTING GUIDE

The system should respond correctly to all voice commands without difficulty. If problems are encountered, try the following solutions.

Where the solutions are listed by number, try each solution in turn, starting with number 1, until the problem is resolved.

Symptom

Solution

The system fails to interpret the command
correctly.

1. Ensure that the command is valid. (See “NISSAN Voice Recognition System (models with navigation system)” (P.4-99).)

2. Ensure that the command is spoken after the tone.

3. Speak clearly without pausing between words and at a level appropriate to the ambient noise level in the vehicle.

4. Ensure that the ambient noise level is not excessive (for example, windows open or defroster on). NOTE: If it is too noisy to
use the phone, it is likely that the voice commands will not be recognized.

5. If more than one command was said at a time, try saying the commands separately.

The system consistently selects the
wrong voicetag.

1. Ensure that the voicetag requested matches what was originally stored. (See “Quick Dial” (P.4-79).)

2. Replace one of the names being confused with a new name.

The system cannot be operated.

Close the soft top (for Roadster models).

Center display, heater, air conditioner, audio, phone and voice recognition systems

4-85

Condition:

(250,1)

[ Edit: 2016/ 2/ 22

Model: 2017MY NISSAN 370Z(Z34) OM17E00Z34U0 ]

4-86

Center display, heater, air conditioner, audio, phone and voice recognition systems

WARNING

Use a phone after stopping your
vehicle in a safe location. If you
have to use a phone while driving,
exercise extreme caution at all
times so full attention may be given
to vehicle operation.

If you find yourself unable to devote
full attention to vehicle operation
while talking on the phone, pull off
the road to a safe location and stop
your vehicle before doing so.

CAUTION

To avoid draining the vehicle battery,
use a phone after starting the engine.

SAA2528

Volume control switch

−/+

PHONE SEND

button

PHONE END

button

Microphone

Your vehicle is equipped with the Bluetooth

Hands-Free Phone System. If you have a
compatible Bluetooth

enabled cellular phone,

you can set up the wireless connection between
your cellular phone and the in-vehicle phone
module. With Bluetooth

wireless technology,

you can make or receive a hands-free telephone
call in your vehicle.

Once your cellular phone is connected to the in-
vehicle phone module, no other phone connect-
ing procedure is required. Your phone is

automatically connected with the in-vehicle
phone module when the ignition switch is
pushed to the ON position with the connected
cellular phone turned on and carried in the
vehicle.

You can connect up to 5 different Bluetooth

cellular phones in the in-vehicle phone module.
However, you can talk on only one cellular phone
at a time.

Before using the Bluetooth

Hands-Free Phone

System, refer to the following notes.

Wireless LAN (Wi-Fi) and the Bluetooth

functions share the same frequency band
(2.4 GHz). Using the Bluetooth

and the

wireless LAN functions at the same time may

Bluetooth

HANDS-FREE PHONE

SYSTEM (models without
navigation system)

Condition:

(251,1)

[ Edit: 2016/ 2/ 22

Model: 2017MY NISSAN 370Z(Z34) OM17E00Z34U0 ]

slow down or disconnect the communica-
tion and cause undesired noise. It is
recommended that you turn off the wireless
LAN (Wi-Fi) when using the Bluetooth

functions.

Set up the wireless connection between a
compatible cellular phone and the in-vehicle
phone module before using the Bluetooth

Hands-Free Phone System.

Some Bluetooth

enabled cellular phones

may not be recognized by the in-vehicle
phone module. Please visit www.nissanusa.
com/bluetooth for a recommended phone
list and connecting.

You will not be able to use a hands-free
phone under the following conditions:

— Your vehicle is outside of the telephone

service area.

— Your vehicle is in an area where it is

difficult to receive radio waves; such as in
a tunnel, in an underground parking
garage, near a tall building or in a
mountainous area.

— Your cellular phone is locked to prevent it

from being dialed.

When the radio wave condition is not ideal
or ambient sound is too loud, it may be
difficult to hear the other person’s voice
during a call.

Immediately after the ignition switch is
pushed to the ON position, it may be
impossible to receive a call for a short
period of time.

Do not place the cellular phone in an area
surrounded by metal or far away from the in-
vehicle phone module to prevent tone quality
degradation and wireless connection dis-
ruption.

While a cellular phone is connected through
the Bluetooth

wireless connection, the

battery power of the cellular phone may
discharge quicker than usual. The Blue-
tooth

Hands-Free Phone System cannot

charge cellular phones.

If the Bluetooth

Hands-Free Phone System

seems to be malfunctioning, it is recom-
mended to contact a NISSAN dealer.

Some cellular phones or other devices may
cause interference or a buzzing noise to
come from the audio system speakers.
Storing the device in a different location
may reduce or eliminate the noise.

Refer to the cellular phone Owner’s Manual
regarding battery charging, cellular phone
antenna, etc.

This wireless hands free car kit is based on
Bluetooth

technology,

— Frequency: 2402 MHz - 2480 MHz

— Output Power: 4.14 dBm E.I.R.P

— Modulation: FHSS GFSK 8DPSK, p/

4DQPSK

— Number of Channel: 79

— This wireless equipment can’t be used

for any services related to safety because
there is the possibility of radio interfer-
ence.

REGULATORY INFORMATION

FCC Regulatory information

CAUTION: To maintain compliance with
FCC’s RF exposure guidelines, use only
the supplied antenna. Unauthorized antenna,
modification, or attachments could damage
the transmitter and may violate FCC regula-
tions.

Operation is subject to the following two
conditions:

1. this device may not cause interference and

2. this device must accept any interference,

including interference that may cause un-
desired operation of the device

Center display, heater, air conditioner, audio, phone and voice recognition systems

4-87

Condition:

(252,1)

[ Edit: 2016/ 2/ 22

Model: 2017MY NISSAN 370Z(Z34) OM17E00Z34U0 ]

4-88

Center display, heater, air conditioner, audio, phone and voice recognition systems

IC Regulatory information

Operation is subject to the following two
conditions: (1) this device may not cause
interference, and (2) this device must accept
any interference, including interference that
may cause undesired operation of the
device.

This Class B digital apparatus meets all
requirements of the Canadian Interference-
Causing Equipment Regulations.

Bluetooth

trademark

Bluetooth

is a trademark owned

Bluetooth

SIG,

Inc.,

and

licensed to Visteon Corporation.

USING THE SYSTEM

The NISSAN Voice Recognition system allows
hands-free operation of the Bluetooth

Hands-

Free Phone System.

If the vehicle is in motion, some commands may
not be available so full attention may be given to
vehicle operation.

Initialization

When the ignition switch is pushed to the ON
position, NISSAN Voice Recognition is initia-
lized, which may take up to one minute. If the

button is pushed before the initialization

completes, the system will accept any com-

mand.

Operating tips

To get the best performance out of the NISSAN
Voice Recognition system, observe the follow-
ing:

Keep the interior of the vehicle as quiet as
possible. Close the windows to eliminate
surrounding noises (traffic noises, vibration
sounds, etc.), which may prevent the system
from recognizing voice commands correctly.

Wait until the tone sounds before speaking a
command. Otherwise, the command will not
be received properly.

Start speaking a command within 5 seconds
after the tone sounds.

Speak in a natural voice without pausing
between words.

Giving voice command

To operate NISSAN Voice Recognition, push
and release the

button located on the

steering wheel. After the tone sounds, speak a
command.

The command given is picked up by the
microphone, and voice feedback is given when
the command is accepted.

If you need to hear the available commands
for the current menu again, say “Help” and

the system will repeat them.

If a command is not recognized, the system
announces, “Command not recognized.
Please say again.” Repeat the command in
a clear voice.

If you want to go back to the previous
command, you can say “Go back” or
“Correction” anytime the system is waiting
for a response.

You can cancel a command when the
system is waiting for a response by saying,
“Cancel” or “Quit.” The system announces
“Cancel” and ends the VR session. You can
also push and hold the

button for 5

seconds on the steering wheel at any time to
cancel the VR session. Whenever the VR
session is cancelled, a double beep is
played to indicate you have exited the
system.

If you want to adjust the volume of the voice
feedback, push the volume control switch (+
or

−) on the steering wheel while being

provided with feedback. You can also use
the radio volume control knob.

Voice Prompt Interrupt:

In most cases you can interrupt the voice
feedback to speak the next command by
pressing the

button on the steering wheel.

Condition:

(253,1)

[ Edit: 2016/ 2/ 22

Model: 2017MY NISSAN 370Z(Z34) OM17E00Z34U0 ]

One Shot Call:

To use the system faster, you may speak the
second level commands with the main menu
command on the main menu. For example, push
the

button and after the tone say, “Call

Redial.” Note: The combined command of Call
and (a Name) cannot be used.

How to say numbers

NISSAN Voice Recognition requires a certain
way to speak numbers in voice commands.
Refer to the rules and examples below.

Either “zero” or “oh” can be used for “0”.

Example: 1-800-662-6200

— “One eight oh oh six six two six two oh

oh”, or

— “One eight zero zero six six two six two

oh oh”

Words can be used for the first 4 digits
places only.

Example: 1-800-662-6200

— “One eight hundred six six two six two oh

oh”,

— NOT “One eight hundred six six two sixty

two hundred, and

— NOT “One eight oh oh six six two sixty

two hundred.

Numbers can be spoken in small groups.
The system will prompt you to continuing
entering digits, if desired.

Example: 1-800-662-6200

— “One eight zero zero”

The system repeats the numbers and
prompts you to enter more.

— “six six two”

The system repeats the numbers and
prompts you to enter more.

— “six two zero zero”

You can say “Star” for “*” and “Pound” for
“#” at any time in any position of the phone
number. (Available only when using the
“Special Number” command.)

Example: 1-555-1212 *123

— “One five five five one two one two star

one two three”

Say “pound” for “#”. Say “star” for “*”
(available when using the “Special Number”
command and the “Send” command during
a call).

Say “plus” for “+” (available only when using
the “Special Number” command).

Say “pause” for a 2 second pause (available
only when storing a phone book number).

See “Making a call by entering a phone
number” (P.4-91) and “List of voice com-
mands” (P.4-91) for more information.

NOTE:

For best results, say phone numbers as
single digits.

The voice command “Help” is available at any
time. Please say the “Help” command to get
information about how to use the system.

INFO

If you are controlling the telephone system
by voice command for the first time or do not
know the appropriate voice command,
speak “Help”. The system announces the
available commands.

When you speak numbers, you can speak
both “zero” or “oh” for “0”.

Manual command selection

Commands can be selected manually. While the
commands are displayed on the audio screen,
select a command by operating the audio tuning
switch, and then push the

button. Once a

command is manually selected, the voice
command function is cancelled. To return to
voice command mode, push the

button to

cancel the current operation, and then perform
the first procedure of voice command.

Center display, heater, air conditioner, audio, phone and voice recognition systems

4-89

Condition:

(254,1)

[ Edit: 2016/ 2/ 22

Model: 2017MY NISSAN 370Z(Z34) OM17E00Z34U0 ]

4-90

Center display, heater, air conditioner, audio, phone and voice recognition systems

SAA2557

CONTROL BUTTONS

The control buttons for the Bluetooth

Hands-

Free Phone System are located on the steering
wheel.

PHONE SEND

Push the

button to initiate a VR session or

answer an incoming call.

You can also use the

button to interrupt

system feedback and give a command at once.

PHONE END

While the voice recognition system is active,
push the

button to go back one step. Push

and hold the

button for 5 seconds to quit

the voice recognition system at any time.

GETTING STARTED

The following procedures will help you get
started using the Bluetooth

Hands-Free Phone

System with NISSAN Voice Recognition. For
additional command options, refer to “List of
voice commands” (P.4-91).

Choosing a language

You can interact with the Bluetooth

Hands-

Free Phone System using English, Spanish or
French.

To change the language, perform the following.

1. Push and hold the

button for more than

5 seconds.

2. The system announces: “Press the PHONE

SEND (

) button for the hands-free

phone system to enter the speaker adapta-
tion mode or press the PHONE END (

)

button to select a different language.”

3. Push the

button.

For information on speaker adaptation, see
“Speaker Adaptation (SA) mode” (P.4-95).

4. The system announces the current language

and gives you the option to change the
language to Spanish (in Spanish) or French
(in French). Use the following chart to select
the language.

NOTE:
You must push the

button or the

button within 5 seconds to change

the language.

Current lan-

guage

Push

(TALK/

PHONE SEND)

to select

Push

(MODE/

PHONE END)

to select

English

Spanish

French

Spanish

English

French

English

Spanish

5. If you decide not to change the language, do

not push either button. After 5 seconds, the
VR session will end, and the language will
not be changed.

Connecting procedure

NOTE:

The connecting procedure must be per-
formed when the vehicle is stationary. If
the vehicle starts moving during the pro-
cedure, the procedure will be cancelled.

Condition:

(255,1)

[ Edit: 2016/ 2/ 22

Model: 2017MY NISSAN 370Z(Z34) OM17E00Z34U0 ]

1. Push the

button on the steering wheel.

The system announces the available com-
mands.

2. Say: “Connect Phone”

. The system

acknowledges the command and an-
nounces the next set of available commands.

3. Say: “Add phone”

. The system acknowl-

edges the command and asks you to initiate
pairing from the phone handset

The connecting procedure of the cellular
phone varies according to each cellular
phone. See the cellular phone Owner’s
Manual for details. You can also visit www.
nissanusa.com/bluetooth for instructions on
connecting NISSAN recommended cellular
phones.

When prompted for a Passkey code, enter
“1234” from the handset. The Passkey code
“1234” has been assigned by NISSAN and
cannot be changed.

4. The system asks you to say a name for the

phone

If the name is too long or too short, the
system tells you, then prompts you for a
name again.

Also, if more than one phone is connected
and the name sounds too much like a name
already used, the system tells you, then

prompts you for a name again.

Making a call by entering a phone
number

1. Push the

button on steering wheel. A

tone will sound.

2. Say: “Call”

. The system acknowledges

the command and announces the next set of
available commands.

3. Say: “Phone Number”

. The system

acknowledges the command and an-
nounces the next set of available commands.
Say: “Special Number” to dial more than 10
digits or any special characters.

4. Say the number you wish to call starting with

the area code in single digit format. If the
system has trouble recognizing the correct
phone number, try entering the number in
the following groups: 3-digit area code, 3-
digit prefix and the last 4-digits. For example,
555-121-3354 can be said as “five five five”
as the 1st group, then “one two one” as the
2nd group, and “three three five four” as the
3rd group. For dialing more than 10 digits or

any special characters, say “Special Num-
ber”. See “How to say numbers” (P.4-89),
for more information.

5. When you have finished speaking the phone

number, the system repeats it back and
announces the available commands.

6. Say: “Dial”

. The system acknowledges

the command and makes the call.

For additional command options, see “List of
voice commands” (P.4-91).

Receiving a call

To receive a call, push the

button on the

steering wheel when you hear the ring tone.

Once the call has ended, push the

button

on the steering wheel.

NOTE:

If you do not wish to take the call when you
hear the ring tone, push the

button on

the steering wheel to reject the call.

LIST OF VOICE COMMANDS

Center display, heater, air conditioner, audio, phone and voice recognition systems

4-91

Condition:

(256,1)

[ Edit: 2016/ 2/ 22

Model: 2017MY NISSAN 370Z(Z34) OM17E00Z34U0 ]

4-92

Center display, heater, air conditioner, audio, phone and voice recognition systems

When you push and release the

button on

the steering wheel, you can choose from the
commands on the Main Menu. The following
pages describe these commands and the
commands in each sub-menu.

Remember to wait for the tone before
speaking.

You can say “Help” to hear the list of commands
currently available anytime the system is waiting
for a response.

A menu item can also be selected by scrolling
the display with the SEEK switch and entering
by pushing the

button.

If you want to end an action without completing
it, you can say “Cancel” or “Quit” at anytime the
system is waiting for a response. The system will
end the VR session. Whenever the VR session
is cancelled, a double beep is played to indicate
you have exited the system.

If you want to go back to the previous command,
you can say “Go back” or “Correction” anytime
the system is waiting for a response.

Call

(Speak Name)

If there are entries stored in the phonebook, a
number associated with a name and location
can be dialed.

See “Phonebook (phones without automatic
phonebook download function)” (P.4-93) to
learn how to store entries.

When prompted by the system, say the name of
the phonebook entry to call. The system
acknowledges the name.

If there are multiple locations associated with
the name, the system asks the user to choose
the location.

Once the name and location are confirmed, the
system begins the call.

“Phone Number” (speak digits)

When prompted by the system, say the number
to call. Refer to “Making a call by entering a
phone number” (P.4-91) for more details.

“Redial”

Use the Redial command to call the last number
that was dialed.

The system acknowledges the command, re-
peats the number and begins dialing.

If a redial number does not exist, the system
announces, “There is no number to redial” and
ends the VR session.

“Call back”

Use the Call Back command to dial the number
of the last incoming call within the vehicle.

The system acknowledges the command, re-
peats the number and begins dialing.

If a call back number does not exist, the system
announces, “There is no number to call back”
and ends the VR session.

“Special Number”

To dial more than 10 digits or any special
characters, please say “Special Number”. When
the system acknowledges the command, the
system will prompt you to speak the number.

“During a call”

During a call there are several command options
available. Push the

button on the steering

wheel to mute the receiving voice and enter
commands.

Condition:

(257,1)

[ Edit: 2016/ 2/ 22

Model: 2017MY NISSAN 370Z(Z34) OM17E00Z34U0 ]

“Help” — The system announces the avail-
able commands.

“Go back/Correction” — The system an-
nounces “Go back,” ends the VR session
and returns to the call.

“Cancel/Quit” — The system announces
“Cancel,” ends the VR session and returns
to the call.

“Send/Enter/Call/Dial” — Use the Send
command to enter numbers, “*” or “#”
during a call. For example, if you were
directed to dial an extension by an auto-
mated system:

Say: “Send one two three four.”

The system acknowledges the command
and sends the tones associated with the
numbers. The system then ends the VR
session and returns to the call. Say “star” for
“*”, say “pound” for “#”.

“Transfer call” — Use the Transfer Call
command to transfer the call from the
Bluetooth

Hands-Free Phone System to

the cellular phone when privacy is desired.

The system announces, “Transfer call. Call
transferred to privacy mode.” The system
then ends the VR session.

To reconnect a call from the cellular phone
to the Bluetooth

Hands-Free Phone sys-

tem, push the

button.

“Mute” — Use the Mute command to mute
your voice so the other party cannot hear it.
Use the mute command again to unmute
your voice.

NOTE:

If a call is ended or the cellular phone
network connection is lost while the Mute
feature is on, the Mute feature will be reset
to “off” for the next call so the other party
can hear your voice.

Phonebook (phones without automatic
phonebook download function)

“Transfer Entry”

Use the Transfer Entry command to store a new
name in the system.

When prompted by the system, say the name
you would like to give the new entry.

For example, say: “Mary.”

If the name is too long or too short, the system
tells you, then prompts you for a name again.

Also, if the name sounds too much like a name

already stored, the system tells you, then
prompts you for a name again.

The system will ask you to transfer a phone
number stored in the cellular phone’s memory.

To enter a phone number by voice command:

For example, say: “five five five one two one
two.” See “How to say numbers” (P.4-89) for
more information.

To transfer a phone number stored in the cellular
phone’s memory:

Say: “Transfer entry.” The system acknowledges
the command and asks you to initiate the
transfer from the phone handset. The new
contact phone number will be transferred from
the cellular phone via the Bluetooth

commu-

nication link.

The transfer procedure varies according to each
cellular phone. See the cellular phone Owner’s
Manual for details. You can also visit www.
nissanusa.com/bluetooth for instructions on
transferring phone numbers from NISSAN re-
commended cellular phones.

The system repeats the number and prompts
you for the next command. When you have
finished entering numbers or transferring an
entry, choose “Store.”

The system confirms the name, location and
number.

Center display, heater, air conditioner, audio, phone and voice recognition systems

4-93

Condition:

Nissan 370Z Roadster (2017 year). Instruction - part 16