Nissan Note E12. Manual - part 648

TM-150

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

P0706 TRANSMISSION RANGE SENSOR A

7.

CHECK CIRCUIT BETWEEN IPDM E/R AND TRANSMISSION RANGE SWITCH

1. Disconnect IPDM E/R connector.

2. Check continuity between IPDM E/R harness connector and transmission range switch.

Is the check result normal?

YES

>> GO TO 8.

NO

>> Repair or replace malfunctioning parts.

8.

DETECT MALFUNCTIONING ITEMS

Check the following items:

• Open circuit or short circuit in harness between ignition switch and IPDM E/R. Refer to 

PG-22, "Wiring Dia-

gram — Ignition Power Supply —"

.

• Short circuit in harness between IPDM E/R harness connector terminal 21 and transmission range switch

harness connector terminal 4.

• 10A fuse (No. 49, IPDM E/R). Refer to 

PG-39, "IPDM E/R Terminal Arrangement"

.

• IPDM E/R
Is the check result normal?

YES

>> Check intermittent incident. Refer to 

GI-41, "Intermittent Incident"

.

NO

>> Repair or replace malfunctioning parts.

Component Inspection (Transmission Range Switch)

INFOID:0000000009019928

1.

CHECK TRANSMISSION RANGE SWITCH

Check continuity between transmission range switch connector terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> There is a malfunction of transmission range switch. Replace transaxle assembly. Refer to 

TM-

250, "Removal and Installation"

.

IPDM E/R

Transmission range switch

Continuity

Connector

Terminal

Connector

Terminal

E45

21

F52

4

Existed

Transmission range switch

Condition

Continuity

Terminal

7 – 10

Manual lever: “P” and “N” positions

Existed

Other than the above

Not existed

4 – 5

Manual lever: “P” position

Existed

Other than the above

Not existed

4 – 8

Manual lever: “R” position

Existed

Other than the above

Not existed

4 – 9

Manual lever: “N position

Existed

Other than the above

Not existed

4 – 2

Manual lever: “D” position

Existed

Other than the above

Not existed

4 – 6

Manual lever: “L” position

Existed

Other than the above

Not existed

P0711 TRANSMISSION FLUID TEMPERATURE SENSOR A

TM-151

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

P0711 TRANSMISSION FLUID TEMPERATURE SENSOR A

DTC Logic

INFOID:0000000009019929

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at

least 10 seconds, then perform the next test.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

1. Start the engine.

2. Drive the vehicle.

3. Maintain the following conditions for a total of 10 minutes or more.

4. Stop the vehicle.

5. Check the first trip DTC.
Is “P0711” detected?

YES

>> Go to 

TM-166, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009019930

1.

CHECK CVT FLUID TEMPERATURE SENSOR

1. Turn ignition switch OFF.

2. Disconnect CVT unit connector.

3. Check CVT fluid temperature sensor. Refer to 

TM-152, "Component Inspection (CVT Fluid Temperature

Sensor)"

.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-41, "Intermittent Incident"

.

NO

>> Repair or replace malfunctioning parts.

DTC

Trouble diagnosis name

DTC detection condition

Possible causes

P0711

Transmission Fluid Tempera-
ture Sensor A Circuit Range/
Performance

Under the following diagnosis conditions, CVT 
fluid temperature recognized by TCM does not 
change for 10 minutes or more in a tempera-
ture range.
• Diagnosis condition
- Selector lever: “D” position
- Vehicle speed: 10 km/h (7 MPH) or more
- Engine speed: 450 rpm or more
- Accelerator pedal position: 1.0/8 or more
- TCM power supply voltage: More than 11 V
- CVT fluid temperature: Less than 10

°C

NOTE:
Every time the CVT fluid temperature increas-
es, reset the detection time and start the diag-
nosis again. 

CVT fluid temperature sensor

Selector lever

: “D” position

Accelerator pedal position

: 1.0/8 or more

Vehicle speed

: 20 km/h (12 MPH) or more

TM-152

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

P0711 TRANSMISSION FLUID TEMPERATURE SENSOR A

Component Inspection (CVT Fluid Temperature Sensor) 

INFOID:0000000009019931

1.

CHECK CVT FLUID TEMPERATURE SENSOR

Check resistance between CVT unit connector terminals. 

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> There is a malfunction of CVT fluid temperature sensor. Replace transaxle assembly. Refer to

TM-250, "Removal and Installation"

.

CVT unit

Condition

Resistance

(Approx.)

Terminal

12 – 18

CVT fluid temperature: 20

°C (68°C)

6.5 k

Ω

CVT fluid temperature: 50

°C (122°C)

2.2 k

Ω

CVT fluid temperature: 80

°C (176°C)

0.87 k

Ω

P0712 TRANSMISSION FLUID TEMPERATURE SENSOR A

TM-153

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

P0712 TRANSMISSION FLUID TEMPERATURE SENSOR A

DTC Logic

INFOID:0000000009019932

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at

least 10 seconds, then perform the next test.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

1. Start the engine and wait for 10 seconds or more.

2. Check the first trip DTC.
Is “P0712” detected?

YES

>> Go to 

TM-153, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009019933

1.

CHECK CIRCUIT BETWEEN TCM AND CVT UNIT

1. Turn ignition switch OFF.

2. Disconnect TCM connector and CVT unit connector. 

3. Check continuity between TCM harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace malfunctioning part.

2.

CHECK CVT FLUID TEMPERATURE SENSOR

Check CVT fluid temperature sensor. Refer to 

TM-153, "Component Inspection (CVT Fluid Temperature Sen-

sor)"

.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-41, "Intermittent Incident"

.

NO

>> Repair or replace malfunctioning parts.

Component Inspection (CVT Fluid Temperature Sensor) 

INFOID:0000000009019934

1.

CHECK CVT FLUID TEMPERATURE SENSOR

Check resistance between CVT unit connector terminals. 

DTC

Trouble diagnosis name

DTC detection condition

Possible causes

P0712

Transmission Fluid Tempera-
ture Sensor A Circuit Low

The CVT fluid temperature identified by the 
TCM is 180

°C (356°F) or more continuously 

for 5 seconds or more under the following di-
agnosis conditions:
• Diagnosis conditions
- Ignition switch: ON
- TCM power supply voltage: More than 11 V

• Harness or connector

(CVT fluid temperature sensor circuit is 
shorted to ground)

• CVT fluid temperature sensor

TCM

—

Continuity

Connector

Terminal

F44

12

Ground

Not existed