Nissan Note E12. Manual - part 646

TM-142

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

P0705 TRANSMISSION RANGE SENSOR A

P0705 TRANSMISSION RANGE SENSOR A

DTC Logic

INFOID:0000000009019923

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CAUTION:

Be careful of the driving speed.

1.

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at

least 10 seconds, then perform the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

1. Start the engine.

2. Maintain the following conditions.

3. Shift the selector lever through entire positions from “P” to “L”. (Hold the selector lever at each position for

10 seconds or more.)

4. Check the first trip DTC.
Is “P0705” detected?

YES

>> Go to 

TM-142, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009019924

1.

CHECK TCM INPUT SIGNALS

With CONSULT

1. Turn ignition switch ON.

2. Select “Data Monitor” in “TRANSMISSION”.

3. Select “D POSITION SW”, “N POSITION SW”, “R POSITION SW”, “P POSITION SW” and “L POSITION

SW”.

4. Shift the selector lever through entire positions from “P” to “L” and check ON/OFF of each monitor item. 

DTC

Trouble diagnosis name

DTC detection condition

Possible causes

P0705

Transmission Range Sensor 
A Circuit (PRNDL Input)

Two or more range signals simultaneously 
stay ON continuously for 5 seconds under the 
following diagnosis condition 1 and 2: 
• Diagnosis condition 1 (continued for 5 sec-

onds or more) 

- TCM power supply voltage: More than 11 V
• Diagnosis condition 2 (continued for 2 sec-

onds or more) 

- Vehicle speed: Less than 3 km/h (2 MPH)
- Accelerator pedal position: 0.6/8 or less
- Idle switch: ON 
- Stop lamp switch: ON

• Harness or connector

(Short circuit between transmission 
range switch and TCM)

• Transmission range switch

Accelerator pedal position

: 0.0/8

Brake pedal

: Depressed

Vehicle speed

: 0 km/h (0 MPH)

Monitor item

Test condition

Condition

D POSITION SW

Selector lever: “D” position

On

Other than the above

Off

P0705 TRANSMISSION RANGE SENSOR A

TM-143

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

Without CONSULT

1. Turn ignition switch OFF.

2. Disconnect TCM connector.

3. Turn ignition switch ON.

4. Shift the selector lever from “P” to “L” and check voltage between TCM harness connector terminals and

ground. 

Is the inspection result normal?

YES 

>> Check intermittent incident. Refer to 

GI-41, "Intermittent Incident"

.

NO-1 [“D POSITION SW” is “ON” when selector is not in “D” position. (Or connector terminal 4 is at power

voltage.)]>>GO TO 2.

NO-2 [“N POSITION SW” is “ON” when selector is not in “N” position. (Or connector terminal 5 is at power

voltage.)]>>GO TO 4.

NO-3 [“R POSITION SW” is “ON” when selector is not in “R” position. (Or connector terminal 6 is at power

voltage.)]>>GO TO 6.

NO-4 [“P POSITION SW” is “ON” when selector is not in “P” position. (Or connector terminal 7 is at power

voltage.)]>>GO TO 8.

NO-5 [“L POSITION SW” is “ON” when selector is not in “L” position. (Or connector terminal 2 is at power

voltage.)]>>GO TO 10.

2.

CHECK D POSITION SW CIRCUIT (PART 1)

1. Turn ignition switch OFF.

2. Disconnect TCM connector.

3. Check continuity between TCM harness connector terminals.

N POSITION SW

Selector lever: “N” position

On

Other than the above

Off

R POSITION SW

Selector lever: “R” position

On

Other than the above

Off

P POSITION SW

Selector lever: “P” position

On

Other than the above

Off

L POSITION SW

Selector lever: “L” position

On

Other than the above

Off

+

−

Condition

Voltage

TCM

Connector

Terminal

F44

2

Ground

Selector lever: “ L” position

Battery voltage

Other than the above

Approx. 0 V

4

Selector lever: “D” position

Battery voltage

Other than the above

Approx. 0 V

5

Selector lever: “N” position

Battery voltage

Other than the above

Approx. 0 V

6

Selector lever: “R” position

Battery voltage

Other than the above

Approx. 0 V

7

Selector lever: “P” position

Battery voltage

Other than the above

Approx. 0 V

Monitor item

Test condition

Condition

TM-144

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

P0705 TRANSMISSION RANGE SENSOR A

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace malfunctioning parts.

3.

CHECK D POSITION SW CIRCUIT (PART 2)

1. Disconnect transmission position switch connector.

2. Turn ignition switch ON.

3. Check voltage between TCM harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 12.

NO

>> Repair or replace malfunctioning parts.

4.

CHECK N POSITION SW CIRCUIT (PART 1)

1. Turn ignition switch OFF.

2. Disconnect TCM connector.

3. Check continuity between TCM harness connector terminals.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace malfunctioning parts.

5.

CHECK N POSITION SW CIRCUIT (PART 2)

1. Disconnect transmission position switch connector.

2. Turn ignition switch ON.

3. Check voltage between TCM harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 12.

NO

>> Repair or replace malfunctioning parts.

TCM

Continuity

Connector

Terminal

F44

4

2

Not existed

5

6

7

+

−

Voltage

(Approx.)

TCM

Connector

Terminal

F44

4

Ground

0 V

TCM

Continuity

Connector

Terminal

F44

5

2

Not existed

4

6

7

+

−

Voltage

(Approx.)

TCM

Connector

Terminal

F44

5

Ground

0 V

P0705 TRANSMISSION RANGE SENSOR A

TM-145

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

6.

CHECK P POSITION SW CIRCUIT (PART 1)

1. Turn ignition switch OFF.

2. Disconnect TCM connector.

3. Check continuity between TCM harness connector terminals.

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Repair or replace malfunctioning parts.

7.

CHECK P POSITION SW CIRCUIT (PART 2)

1. Disconnect transmission position switch connector.

2. Turn ignition switch ON.

3. Check voltage between TCM harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 12.

NO

>> Repair or replace malfunctioning parts.

8.

CHECK R POSITION SW CIRCUIT (PART1)

1. Turn ignition switch OFF.

2. Disconnect TCM connector.

3. Check continuity between TCM harness connector terminals.

Is the inspection result normal?

YES

>> GO TO 9.

NO

>> Repair or replace malfunctioning parts.

9.

CHECK R POSITION SW CIRCUIT (PART 2)

1. Disconnect transmission position switch connector.

2. Turn ignition switch ON.

3. Check voltage between TCM harness connector terminal and ground.

TCM

Continuity

Connector

Terminal

F44

7

2

Not existed

4

5

6

+

−

Voltage

(Approx.)

TCM

Connector

Terminal

F44

7

Ground

0 V

TCM

Continuity

Connector

Terminal

F44

6

2

Not existed

4

5

7