Qashqai J11. Transaxle & Transmission - part 38

TM-594

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10G]

P2765 INPUT SPEED SENSOR B

>> GO TO 2.

2.

CHECK DTC DETECTION

1.

Start the engine.

2.

Drive the vehicle.

3.

Maintain the following conditions for 10 seconds or more.

4.

Stop the vehicle.

5.

Check the first trip DTC.

Is “P2765” detected?

YES

>> Go to 

TM-594, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000010245652

1.

CHECK OUTPUT SPEED SENSOR POWER CIRCUIT 

1.

Turn ignition switch OFF.

2.

Disconnect output speed sensor connector.

3.

Turn ignition switch ON.

4.

Check voltage between output speed sensor harness connector terminal and ground. 

Is the inspection result normal?

YES 

>> GO TO 2.

NO

>> GO TO 6.

2.

CHECK OUTPUT SPEED SENSOR GROUND CIRCUIT 

Check continuity between output speed sensor harness connector terminal and ground. 

Is the inspection result normal?

YES 

>> GO TO 3.

NO

>> Repair or replace malfunctioning parts.

3.

CHECK CIRCUIT BETWEEN OUTPUT SPEED SENSOR AND TCM (PART 1)

1.

Turn ignition switch OFF.

2.

Disconnect TCM connector.

3.

Check continuity between output speed sensor harness connector terminal and TCM harness connector
terminal.

Is the inspection result normal?

Selector lever

: “D” position

Engine speed

: 1,200 rpm or more

Vehicle speed

: 55 km/h (34 MPH) or more

+

−

Voltage

Output speed sensor

Connector

Terminal

F41

3

Ground

10 – 16 V

Output speed sensor

—

Continuity

Connector

Terminal

F41

1

Ground

Existed

Output speed sensor

TCM

Continuity

Connector

Terminal

Connector

Terminal

F41

2

F1

34

Existed

P2765 INPUT SPEED SENSOR B

TM-595

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10G]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

YES 

>> GO TO 4.

NO

>> Repair or replace malfunctioning parts.

4.

CHECK CIRCUIT BETWEEN OUTPUT SPEED SENSOR AND TCM (PART 2)

Check continuity between output speed sensor harness connector terminal and ground. 

Is the inspection result normal?

YES 

>> GO TO 5.

NO

>> Repair or replace malfunctioning parts.

5.

CHECK TCM INPUT SIGNALS

1.

Connect all of disconnected connectors.

2.

Lift the vehicle.

3.

Start the engine.

4.

Check frequency of output speed sensor.

Is the inspection result normal?

YES 

>> Check intermittent incident. Refer to 

GI-41, "Intermittent Incident"

.

NO

>> Replace output speed sensor. Refer to 

TM-636, "Removal and Installation"

.

6.

DETECT MALFUNCTIONING ITEMS

Check the following items:
• Open circuit or short circuit in harness between ignition switch and output speed sensor. Refer to 

PG-56,

"Wiring Diagram - IGNITION POWER SUPPLY -"

.

• 10A fuse [No.74, located in fuse block (J/B)]. Refer to 

PG-97, "Fuse, Connector and Terminal Arrangement"

.

• IPDM E/R

Is the check result normal?

YES

>> Check intermittent incident. Refer to 

GI-41, "Intermittent Incident"

.

NO

>> Repair or replace malfunctioning parts.

Output speed sensor

—

Continuity

Connector

Terminal

F41

2

Ground

Not existed

+

−

Condition

Frequency

(Approx.)

TCM

Connector

Terminal

F1

34

Ground

• Shift position: “M1” position
• Vehicle speed: 20 km/h (12 MPH)

200 Hz

JSDIA1904GB

TM-596

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10G]

P2813 SELECT SOLENOID

P2813 SELECT SOLENOID

DTC Logic

INFOID:0000000010245653

DTC DETECTION LOGIC

NOTE:
DC stands for “DRIVING CYCLE” and indicates a series of driving cycle of “Ignition switch OFF 

→

 ON 

→

 driv-

ing 

→

 OFF”.

DTC CONFIRMATION PROCEDURE

CAUTION:

Be careful of the driving speed.

1.

PREPARATION BEFORE WORK

DTC

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

Possible causes

P2813

SELECT SOLENOID
(Select solenoid)

When any of 1, or 2 is satisfied:
1.

When all the following conditions are es-
tablished three times in 1DC

-

Precondition

•

DTC other than the applicable DTC is not 
detected.

•

Throttle position: More than 6.27 deg.

•

Vehicle speed: Less than 3 km/h (1 
MPH)

•

CVT fluid temperature: More than 20

°

C 

(68

°

F)

•

Selector lever: Other than P, N

•

Turbine speed when performed N 

→

 D, 

N (P) 

→

 R: More than 500 rpm

•

TCM power supply voltage: More than 11 
V

-

Detection time

•

N 

→

 D: 0.4 seconds

•

N 

→

 R: 0.3 seconds

•

P 

→

 R: 0.3 seconds

2.

When all of the following conditions are 
satisfied and this state is maintained for 
30 seconds:

-

The counting of time continues while all 
of the following conditions are satisfied 
and stops when the conditions become 
unsatisfied (the count is maintained). 
When accumulated time reaches 30 sec-
onds (Clutch is judged as engaged and 
the count is reset.)

•

Selector lever: Other than P, N

•

Vehicle speed: Less than 3 km/h (1 
MPH)

•

Differences between primary pulley 
speed and secondary speed: Less than 
120 rpm

•

Clutch instructions pressure: 0.95 MPa 
or more

•

Differences between turbine speed and 
input speed: Less than 200 rpm

•

Turbine speed – speed: More than 450 
rpm

•

 DTC other than the applicable DTC is 
not detected.

•

TCM power supply voltage: More than 11 
V

Select solenoid valve

P2813 SELECT SOLENOID

TM-597

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10G]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION 1

1.

Start the engine.

2.

Maintain the following conditions. (Keep 30seconds or more after the selector lever shifted.)

3.

Check the first trip DTC.

Is “P2813”detected?

YES

>> Go to 

TM-597, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000010245654

1.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-41, "Intermittent Incident"

.

Is the inspection result normal?

YES 

>> Replace transaxle assembly. Refer to 

TM-653, "Removal and Installation"

.

NO

>> Repair or replace malfunctioning parts.

Selector lever

: N

→

 D, N 

→

 R, P

→

 R

TM-598

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10G]

P2814 SELECT SOLENOID

P2814 SELECT SOLENOID

DTC Logic

INFOID:0000000010245655

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CAUTION:

Be careful of the driving speed.

1.

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

1.

Start the engine.

2.

Maintain the following conditions. (Keep 5 seconds or more after the selector lever shifted.)

3.

Check the first trip DTC.

Is “P2814” detected?

YES

>> Go to 

TM-598, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000010245656

1.

CHECK CIRCUIT BETWEEN TCM AND CVT UNIT

1.

Turn ignition switch OFF.

2.

Disconnect TCM connector and CVT unit connector.

3.

Check continuity between TCM harness connector terminal and ground. 

Is the inspection result normal?

YES 

>> GO TO 2.

NO

>> Repair or replace damaged parts.

2.

CHECK CIRCUIT BETWEEN CVT UNIT AND GROUND

Check continuity between CVT unit harness connector terminal and ground. 

DTC

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

Possible causes

P2814

SELECT SOLENOID
(Select solenoid)

When all of the following conditions are satis-
fied and this state is maintained for 0.48 sec-
onds:
• TCM power supply voltage: 11 V or more
• TCM judges that solenoid valve circuit is 

shorted to ground.

• Harness or connector

(Select solenoid valve circuit shorted to 
ground)

• Select solenoid valve

Selector lever

: N 

→

 D, N 

→

 R, P 

→

 R

TCM

—

Continuity

Connector

Terminal

F1

37

Ground

Not existed

P2814 SELECT SOLENOID

TM-599

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10G]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

Is the inspection result normal?

YES 

>> Check intermittent incident. Refer to 

GI-41, "Intermittent Incident"

.

NO

>> There is malfunction of select solenoid valve. Replace transaxle assembly. Refer to 

TM-653,

"Removal and Installation"

.

CVT unit

—

Condition

Resistance

Connector

Terminal

F207

4

Ground

CVT fluid temperature: 20

°

C (68

°

F)

5.5 – 7.0 

Ω

CVT fluid temperature: 50

°

C (122

°

F)

6.0 – 8.0 

Ω

CVT fluid temperature: 80

°

C (176

°

F)

6.5 – 8.5 

Ω

TM-600

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10G]

P2815 SELECT SOLENOID

P2815 SELECT SOLENOID

DTC Logic

INFOID:0000000010245657

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

1.

Start the engine.

2.

Maintain the following conditions. (Keep 5 seconds or more after the selector lever shifted.)

3.

Check the first trip DTC.

Is “P2815” detected?

YES

>> Go to 

TM-600, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000010245658

1.

CHECK CIRCUIT BETWEEN TCM AND CVT UNIT

1.

Turn ignition switch OFF.

2.

Disconnect TCM connector and CVT unit connector.

3.

Check continuity between TCM harness connector terminal and ground. 

Is the inspection result normal?

YES 

>> GO TO 2.

NO

>> Repair or replace damaged parts.

2.

CHECK CIRCUIT BETWEEN CVT UNIT AND GROUND

Check continuity between CVT unit harness connector terminal and ground. 

DTC

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

Possible causes

P2815

SELECT SOLENOID
(Select solenoid)

When all of the following conditions are satis-
fied and this state is maintained for 0.2 sec-
onds:
• TCM power supply voltage: More than 11 V
• TCM judges that solenoid valve circuit is 

open. 

• P2814 is not detected. 

• Harness or connector

(Select solenoid valve circuit open or 
shorted to power supply)

• Select solenoid valve

Selector lever

: N 

→

 D, N 

→

 R, P 

→

 R

TCM

CVT unit

Continuity

Connector

Terminal

Connector

Terminal

F1

37

F58

4

Existed

P2815 SELECT SOLENOID

TM-601

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10G]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

Is the inspection result normal?

YES 

>> Check intermittent incident. Refer to 

GI-41, "Intermittent Incident"

.

NO

>> There is malfunction of select solenoid valve. Replace transaxle assembly. Refer to 

TM-653,

"Removal and Installation"

.

CVT unit

—

Condition

Resistance

Connector

Terminal

F207

4

Ground

CVT fluid temperature: 20

°

C (68

°

F)

5.5 – 7.0 

Ω

CVT fluid temperature: 50

°

C (122

°

F)

6.0 – 8.0 

Ω

CVT fluid temperature: 80

°

C (176

°

F)

6.5 – 8.5 

Ω

TM-602

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10G]

MAIN POWER SUPPLY AND GROUND CIRCUIT

MAIN POWER SUPPLY AND GROUND CIRCUIT

Diagnosis Procedure

INFOID:0000000010245659

1.

CHECK TCM POWER CIRCUIT (PART 1)

1.

Turn ignition switch OFF.

2.

Disconnect TCM connector.

3.

Check voltage between TCM harness connector terminals and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> GO TO 4.

2.

CHECK TCM POWER CIRCUIT (PART 2)

Check voltage between TCM harness connector terminals and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 5.

3.

CHECK TCM GROUND CIRCUIT

Check continuity between TCM harness connector terminals and ground.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-41, "Intermittent Incident"

.

NO

>> Repair or replace malfunctioning parts.

4.

DETECT MALFUNCTION ITEMS (PART 1)

Check the following items:
• Open circuit or short circuit in harness between battery positive terminal and TCM connector terminal 45,

and 46.

• 10A fuse (No.81, located in the fuse and fusible link block). Refer to 

PG-99, "Fuse and Fusible Link Arrange-

ment (Gasilone Engine)"

.

Is the inspection result normal?

YES >> Check 

intermittent incident. Refer to 

GI-41, "Intermittent Incident"

.

NO

>> Repair or replace malfunctioning parts.

+

−

Voltage

TCM

Connector

Terminal

F1

45

Ground

10 – 16 V

46

+

−

Condition

Voltage

TCM

Connector

Terminal

F1

47

Ground

Ignition switch ON

10 – 16 V

Ignition switch OFF

Approx. 0 V

48

Ignition switch ON

10 – 16 V

Ignition switch OFF

Approx. 0 V

TCM

—

Continuity

Connector

Terminal

F1

41

Ground

Existed

42

MAIN POWER SUPPLY AND GROUND CIRCUIT

TM-603

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10G]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

5.

DETECT MALFUNCTIONING ITEMS (PART 2)

Check the following items:
• Open circuit or short circuit in harness between battery positive terminal and TCM connector terminal 47,

and 48.

• 10A fuse [No.74, located in fuse block (J/B)]. Refer to 

PG-97, "Fuse, Connector and Terminal Arrangement"

.

• IPDM E/R

Is the check result normal?

YES

>> Check intermittent incident. Refer to 

GI-41, "Intermittent Incident"

.

NO

>> Repair or replace malfunctioning parts.

TM-604

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10G]

SHIFT POSITION INDICATOR CIRCUIT

SHIFT POSITION INDICATOR CIRCUIT

Component Parts Function Inspection

INFOID:0000000010245664

1.

CHECK SHIFT POSITION INDICATOR

1.

Start the engine.

2.

Shift selector lever.

3.

Check that the selector lever position and the shift position indicator on the combination meter are identi-
cal.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Go to 

TM-604, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000010245665

1.

CHECK TCM INPUT/OUTPUT SIGNAL 

With CONSULT

1.

Start the engine.

2.

Select “Data Monitor” in “TRANSMISSION”.

3.

Select “RANGE”. 

4.

Shift selector lever.

5.

Check that selector lever position, “RANGE” on CONSULT screen, and shift position indicator display on
combination meter are identical.

Is the check result normal?

YES

>> INSPECTION END

NO-1 (“RANGE” is changed but is not displayed on shift position indicator.>>Check “Self Diagnostic Result”

in “TRANSMISSION”.

NO-2 (“RANGE” and shift position indicator are different.)>>Check “Self Diagnostic Result” in “TRANSMIS-

SION”.

NO-3 (Specific “RANGE” is not displayed on shift position 

indicator.)>>Check “Self Diagnostic Result” in

“METER/M&A”.

SHIFT LOCK SYSTEM

TM-605

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10G]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

SHIFT LOCK SYSTEM

Component Function Check

INFOID:0000000010245666

1.

CHECK SHIFT LOCK OPERATION (PART 1)

1.

Turn ignition ON.

2.

Shift the selector lever to “P” position.

3.

Attempt to shift the selector lever to any other than position with the brake pedal released.

Can the selector lever be shifted to any other position?

YES

>> Go to 

TM-605, "Diagnosis Procedure"

.

NO

>> GO TO 2.

2.

CHECK SHIFT LOCK OPERATION (PART 2)

Attempt to shift the selector lever to any other than position with the brake pedal depressed.

Can the selector lever be shifted to any other position?

YES

>> INSPECTION END

NO

>> Go to 

TM-605, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000010245667

1.

CHECK POWER SOURCE (PART 1)

1.

Turn ignition switch OFF.

2.

Disconnect stop lamp switch connector

3.

Turn ignition switch ON.

4.

Check the voltage between the stop lamp switch harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> GO TO 8.

2.

CHECK STOP LAMP SWITCH (PART 1)

Check stop lamp switch. Refer to 

TM-606, "Component Inspection (Stop Lamp Switch)"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 9.

3.

CHECK CIRCUIT BETWEEN STOP LAMP SWITCH AND CVT SHIFT SELECTOR

1.

Disconnect CVT shift selector connector

2.

Check the continuity between the stop lamp switch harness connector terminal and the CVT shift selector
harness connector terminal.

3.

Also check short circuit in harness.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace the malfunctioning parts.

4.

CHCK GROUND CIRCUIT

+

−

Voltage

Stop lamp switch

Connector

Terminal

E50

3

Ground

Battery voltage

Stop lamp switch

CVT shift selector

Continuity

Connector

Terminal

Connector

Terminal

E50

4

M9

3

Existed

TM-606

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10G]

SHIFT LOCK SYSTEM

Check the continuity between the CVT shift selector harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace the malfunctioning parts.

5.

CHECK PART POSITION SWITCH

1.

Disconnect park position switch connector.

2.

Check park position switch. Refer to 

TM-607, "Component Inspection (Park Position Switch)"

.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace the malfunctioning parts.

6.

CHECK SHIFT LOCK SOLENOID

1.

Disconnect shift lock solenoid connector.

2.

Check shift lock solenoid. Refer to 

TM-607, "Component Inspection (Shift Lock Solenoid)"

.

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Repair or replace the malfunctioning parts.

7.

CHECK CVT SHIFT SELECTOR HARNESS

Check CVT shift selector harness. Refer to 

TM-607, "Component Inspection (CVT Shift Selector Harness)"

.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Repair or replace the malfunctioning parts.

8.

DETECT MALFUNCTIONING ITEM

Check the following items:
• Open circuit or short circuit in harness between ignition switch and stop lamp switch connector. Refer to 

PG-

56, "Wiring Diagram - IGNITION POWER SUPPLY -"

.

• Ignition switch
• 10A fuse [No.4, fuse block (J/B)]. Refer to 

PG-97, "Fuse, Connector and Terminal Arrangement"

.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Repair or replace the malfunctioning parts.

9.

CHECK INSTALLATION POSITION OF STOP LAMP SWITCH

Adjust stop lamp switch position. Refer to 

BR-8, "Inspection and Adjustment"

 (LHD), 

BR-52, "Inspection and

Adjustment"

 (RHD).

>> GO TO 10.

10.

CHECK STOP LAMP SWITCH (PART 2)

Check stop lamp switch. Refer to 

TM-606, "Component Inspection (Stop Lamp Switch)"

.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Repair or replace the malfunctioning parts.

Component Inspection (Stop Lamp Switch)

INFOID:0000000010245669

1.

CHECK STOP LAMP SWITCH

Check continuity between the stop lamp switch connector terminals.

CVT shift selector

—

Continuity

Connector

Terminal

M9

4

Ground

Existed

SHIFT LOCK SYSTEM

TM-607

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10G]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace stop lamp switch. Refer to 

BR-17, "Exploded View"

 (LHD), 

BR-61, "Exploded View"

(RHD).

Component Inspection (Park Position Switch)

INFOID:0000000010475026

1.

CHECK PARK POSITION SWITCH

Check continuity between park position switch connector terminals.

CAUTION:

• Connect the fuse between the terminals when applying the voltage.
• Never cause shorting between terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace park position switch. Refer to 

TM-619, "Disassembly and Assembly"

.

Component Inspection (Shift Lock Solenoid)

INFOID:0000000010475027

1.

CHECK SHIFT LOCK SOLENOID

Apply voltage to terminals of shift lock solenoid connector and check that shift lock solenoid is activated.

CAUTION:

• Connect the fuse between the terminals when applying the voltage.
• Never cause shorting between terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace shift lock unit. Refer to 

TM-619, "Disassembly and Assembly"

.

Component Inspection (CVT Shift Selector Harness)

INFOID:0000000010475028

1.

CHECK CVT SHIFT SELECTOR HARNESS (PART 1)

Check continuity between CVT shift selector harness connector terminal and shift lock solenoid harness con-
nector terminal.

Stop lamp switch

Condition

Continuity

Terminal

3 – 4

Depressed brake pedal

Yes

Released brake pedal

No

Park position switch

Condition

Continuity

Terminal

1 – 2

Shift selector lever to “P” position.

Existed

Other than above

Not existed

Shift lock solenoid

Condition

Status

+ (fuse)

−

Terminal

1

2

Apply battery voltage be-
tween terminals 1 and 2.

Shift lock solenoid operates

CVT shift selector

Shift lock solenoid

Continuity

Connector

Terminal

Connector

Terminal

M9

3

M326

1

Existed

TM-608

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10G]

SHIFT LOCK SYSTEM

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace CVT shift selector assembly. Refer to 

TM-617, "Removal and Installation"

.

2.

CHECK CVT SHIFT SELECTOR HARNESS (PART 2)

Check continuity between shift lock solenoid harness connector terminal and park position switch harness
connector terminal.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace CVT shift selector assembly. Refer to 

TM-617, "Removal and Installation"

.

3.

CHECK CVT SHIFT SELECTOR HARNESS (PART 3)

Check continuity between park switch harness connector terminal and CVT shift selector harness connector
terminal.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Replace CVT shift selector harness. Refer to 

TM-617, "Removal and Installation"

.

4.

CHECK CVT SHIFT SELECTOR HARNESS (PART 4)

Check harness cladding CVT shift selector harness for damage.
Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace CVT shift selector assembly. Refer to 

TM-617, "Removal and Installation"

.

Shift lock solenoid

Park position switch

Continuity

Connector

Terminal

Connector

Terminal

M326

2

M325

1

Existed

Park switch

CVT shift selector

Continuity

Connector

Terminal

Connector

Terminal

M325

2

M9

4

Existed

CVT CONTROL SYSTEM

TM-609

< SYMPTOM DIAGNOSIS >

[CVT: RE0F10G]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

SYMPTOM DIAGNOSIS

CVT CONTROL SYSTEM

Symptom Table

INFOID:0000000010245670

• The diagnosis item number indicates the order of check. Start checking in the order from 1. 
• Perform diagnoses of symptom table 1 before symptom table 2.

Symptom Table 1

Symptom

En

gi

ne sy

st

em

CAN communication 

line

T

ra

n

s

m

is

s

io

n

 ra

ng

e s

w

itc

h

 (P07

05

, P0

70

6)

In

p

u

t sp

ee

d se

ns

or (P0

7

1

7

)

Prim

ary

 spe

e

d

 se

ns

or (P07

15

)

Out

p

u

t s

p

e

e

d

 se

ns

or 

(P27

65

)

CVT 

flu

id

 tem

p

erat

ure

 se

ns

o

r (P07

12

, P0

71

3)

Pri

m

a

ry p

res

s

u

re

 se

ns

or 

(P08

4C, 

P08

4

D)

Sec

o

n

d

a

ry pre

s

s

u

re

 se

ns

or (P08

41

, 

P0

84

7,

 P08

4

8

)

T

o

rq

ue

 co

nv

ert

e

r c

lu

tc

h

 s

o

le

n

o

id

 v

a

lv

e

 (P07

40

, P

0

7

43,

 P0

74

4)

St

a

ll t

e

s

t

CVT position 

Power suppl

y

 

Control valve

CVT

 f

lui

d l

e

v

e

l an

d s

ta

te

Ig

ni

tio

n

 switch

 an

d st

a

rter

EC

9-

1

3

7

TM-485

TM-50

8

TM-61

9

TM-60

2

TM-62

9

TM-61

5

PG-56

, 

STR-18

Shift Shock

Large shock (N

→

D  position)

1

4

7

3

6

2

8

5

Large shock (N

→

R  position)

1

4

7

3

6

2

8

5

Shock is too large for lock-up.

2

3

6

1

5

4

Slips/Will Not 
Engage

Vehicle cannot be started from D posi-
tion.

8

3

5

6

7

9

10

11

4

2

12

13

1

Vehicle cannot be started from R posi-
tion.

8

3

5

6

7

9

10

11

4

2

12

13

1

Does not lock-up.

2

6

8

3

4

10

9

11

12

5

7

13

1

Does not hold lock-up condition.

2

6

8

3

4

10

9

11

12

5

7

13

1

Lock-up is not released.

2

6

3

4

5

7

8

1

With selector lever in D position, ac-
celeration is extremely poor.

3

4

5

7

8

9

12

10

11

2

6

13

14

1

With selector lever in R position, ac-
celeration is extremely poor.

3

4

5

7

8

9

12

10

11

2

6

13

14

1

Slips at lock-up.

2

6

8

3

4

10

9

11

12

5

7

13

1