Frelander 2. Manual - part 456

 

  Index      Land Rover     Land Rover Frelander 2 - service repair manual 2006-2010 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  454  455  456  457   ..

 

 

Frelander 2. Manual - part 456

 

 

General Information

YES /

NO

 

YES /

NO

 

Diagnostics (Battery Testing)

 

 

 

 

1: Loose battery clamps

Yes

*

No

*

2: Loose hold down clamps

Yes

 

No

 

3: Corroded terminal posts

Yes

*

No

*

4: Physical damage/leaks

Yes

 

No

 

5: Low electrolyte

Yes

*

No

*

6: FEAD belt tension

OK

*

Not OK *

7: Surface charge removed

Yes

*

No

*

8: Voltage (appendix A)

Yes

*

No

*

9: Quiescent Drain

mA

*

 

 

10: Vent tube correctly installed

Yes

 

No

 

11: Midtronics test

 

 

 

 

Code before charging

*

 

 

 

If Midtronics indicates that the battery needs re-charging, charge the
battery for 24 hours

 

 

 

 

Code after charge

*

 

 

 

Result after charge

*

 

 

 

If "good and re-charge" charge the battery for an additional 24 hours.

 

 

 

 

If "charge and re-test" for both before and after 24 hours charge renew the
battery

 

 

 

 

Only renew the battery if "renew battery", "bad cell" or charge and re-test
has been displayed twice.

 

 

 

 

Comments
-
-
-
-
-

Battery and Charging System - General Information - Quiescent Drain

Description and Operation

QUIESCENT DRAIN - TYPICAL VALUES

• NOTE: The quiescent drain after the initial shutdown period should not exceed the value shown in the table.

Land Rover Quiescent Drain Values

MODEL

SHUT DOWN PERIOD

(minutes)

TYPICAL VALUES BATTERY DRAIN

(mA)

Range Rover (LM) - Up to 2009MY

30

16.0 - 18.0

Range Rover (LM) - From 2010MY

20 (after lock/arm condition) ²

<30

33 (unlocked)

<30

Range Rover Sport (LS) - Up to 2007MY

20

<22

Range Rover Sport (LS) - From 2007MY to
2010MY

30

<25

Range Rover Sport (LS) - From 2010MY

3 (after lock/arm condition) ²

<30

33 (unlocked)

<30

Range Rover Evoque (LV) - From 2012MY

20 (after lock and arm condition) <20

Discovery 3/LR3 (LA) - Up to 2007MY

20

<22

Discovery 3/LR3 (LA) - From 2007MY to 2010MY 30

<25

Discovery 4/LR4 (LA) - From 2010MY

3 (after lock/arm condition) ²

<30

33 (unlocked)

<30

Freelander 2/LR2 (LF) - From 2007MY

35 (single locked or unlocked)

<23.6

12 (double locked)

<23.6

Freelander (LN) - Up to 2007MY

10

24-25 - without Becker Navigation
system

10

27-28 - with Becker Navigation system

Defender (LD) - 1998MY to 2007MY

30

<21

Defender (LD) - from 2007MY

<30

<30

Discovery Series 2 (LT)

30

<30

• NOTE:

1. The total current drain will be higher if certain approved accessories are fitted (for example: tracker, trailer module,
etc.)

2. Applies to vehicles without Tire Pressure Monitoring System (TPMS). Vehicle shut-down period with TPMS is
approximately 15 minutes.

Battery and Charging System - General Information - Charging System

Diagnosis and Testing

Principles of Operation

For a detailed description of the charging system, refer to the relevant Description and Operation section in the workshop
manual. REFER to:

Battery Care (414-00, Description and Operation),
Battery and Cables (414-01, Description and Operation),
Generator - ID4 2.4L Diesel (414-02, Description and Operation).

Inspection and Verification

CAUTION: Diagnosis by substitution from a donor vehicle is NOT acceptable. Substitution of control modules does

not guarantee confirmation of a fault, and may also cause additional faults in the vehicle being tested and/or the donor
vehicle.

1. Verify the customer concern.

1.

2. Visually inspect for obvious signs of mechanical or electrical damage.

2.

• NOTE: Check the vehicle battery condition and state of charge before condemning any of the charging system
components. For additional information, refer to the battery care manual.

For a complete list of all diagnostic trouble codes that could be logged on this vehicle, please refer to section 100-00.
REFER to: (100-00)

Diagnostic Trouble Code (DTC) Index - DTC: Engine Control Module (PCM) (Description and Operation),
Diagnostic Trouble Code (DTC) Index - DTC: Instrument Cluster (IPC) (Description and Operation).

Visual Inspection

Mechanical

Electrical

Generator
Drive belt
Drive belt tensioner
Generator pulley
Check the security of the generator fixings

Generator
Battery
Mega-fuse
Engine/generator ground connection
Harness(s)
Electrical connector(s)
Engine Control Module (ECM)
Central junction box (Freelander 2 only)

3. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before

proceeding to the next step

3.

4. If the cause is not visually evident, check for Diagnostic Trouble Codes (DTCs) and refer to the DTC Index.

4.

DTC Index

• NOTE: If the control module or a component is suspect and the vehicle remains under manufacturer warranty, refer to the
Warranty Policy and Procedures manual (section B1.2), or determine if any prior approval programme is in operation, prior
to the installation of a new module/component.

• NOTE: Generic scan tools may not read the codes listed, or may read only five digit codes. Match the five digits from the
scan tool to the first five digits of the seven digit code listed to identify the fault (the last two digits give extra
information read by the manufacturer-approved diagnostic system).

• NOTE: When performing electrical voltage or resistance tests, always use a digital multimeter (DMM) accurate to three
decimal places, and with an up-to-date calibration certificate. When testing resistance, always take the resistance of the
DMM leads into account.

• NOTE: Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests.

• NOTE: If DTCs are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent concern may
be the cause. Always check for loose connections and corroded terminals.

Symptom

Possible Cause

Action

Charge warning lamp does not
illuminate

W arning lamp/circuit -
fault
Generator - internal
fault
CAN Bus - circuit fault
Engine control module
- internal fault

Check the warning lamp function with the
ignition on and the engine off
Repair the circuit as necessary
Check for DTCs indicating a generator, CAN or
engine control module fault

Charge warning lamp stays
on/battery discharges

Accessory drive belt -
fault
Generator pulley
slipping on shaft
Generator - internal

Check the battery and generator cables
Refer to the electrical guides
Check for DTCs indicating a generator fault
Check the accessory drive belt condition and
tension

1

2

1
2
3
4

5
6

1

1

Symptom

Possible Cause

Action

fault
Battery cable - fault
CAN Bus - circuit fault
Engine control module
internal fault
Central junction box

Check that the pulley does not rotate
independently of the generator
Check for DTCs indicating a CAN, central junction
box or engine control module fault

Charge warning lamp intermittent

Accessory drive belt
slipping
Battery cable - fault
Generator - circuit fault
Generator - internal
fault
CAN Bus - circuit fault

• NOTE: Use of a power pack or boost charger may bring
the warning lamp on until disconnected

Check the accessory drive belt condition and
tension
Check the battery and generator cables refer to
the electrical guides
Check for DTCs indicating a generator or CAN
circuit fault

Battery discharges without the
charge warning lamp staying on

Battery - fault
Battery quiescent drain
Intermittent generator
- fault

Check the battery condition
Check for battery quiescent drain
Check for DTCs indicating a generator fault
If no other reason for discharge can be found,
check the circuit. Refer to the electrical guides

Noise (mechanical)

Accessory drive belt
slipping

Check the accessory drive belt condition and
tension
Disconnect the accessory drive belt and check
that the generator rotates freely

Test Procedure

PINPOINT TEST A : BOSCH NON-BMS GENERATOR DIAGNOSTIC FLOW CHART

TEST

CONDITIONS

DETAILS/RESULTS/ACTIONS

A1: MIDTRONICS BATTERY TEST

• NOTE: The battery must be fully charged and any battery defects rectified before continuing with generator diagnosis
• NOTE: The voltmeter must display readings to three decimal places (i.e. 0.001V)
• NOTE: Ignition on is position 2 on a keyed ignition system
• NOTE: Ignition on is two short presses of the start button (power mode 6) with keyless ignition system

Using a Midtronics hand held tester or the Midtronics GR-1 diagnostic charger, carry out the
"Midtronics battery test" as detailed in the battery care manual.
REFER to: Battery Care (414-00, Description and Operation).
Record battery diagnostic result on the provided form

Does the battery pass the "Midtronics battery test"?
Yes

GO to B1

.

No

Rectify any battery defects before continuing with generator diagnosis GO to Pinpoint Test 

B.

PINPOINT TEST B : BOSCH NON-BMS GENERATOR DIAGNOSTIC FLOW CHART

TEST

CONDITIONS

DETAILS/RESULTS/ACTIONS

B1: GENERATOR OUTPUT

• NOTE: Freelander 2 = The heated rear screen is timed to operate for 12 minutes
• NOTE: Defender = The heated rear screen is timed to operate for 8 minutes

Connect a voltmeter to the vehicle battery
Switch ignition state to on (engine off)
Turn off all electrical loads e.g. (blower, radio, interior lights etc.)
Start the engine, switch on the heated rear screen

Ensure the heated rear screen is on (see note above) and that the air conditioning system is off.

Wait 90 seconds
Record the battery voltage (V1) shown on the multimeter

Does battery voltage (V1) = 14.8 volts or greater at idle?
Yes

Install a new generator. Refer to the warranty policy and procedures manual, or determine if any
prior approval programme is in operation, prior to the installation of a new module/component

No

GO to B2

.

B2: BATTERY VOLTAGE AT IDLE

Using battery voltage reading (V1)

Does battery voltage (V1) = 13 volts or greater at idle (But less than 14.8 volts)?
Yes

GO to B3

.

No

GO to Pinpoint Test 

C.

B3: BATTERY WARNING LAMP

The battery voltage is (V1) = 13 volts or greater at idle (but less than 14.8 volts)

 

 

 

 

 

 

 

Content   ..  454  455  456  457   ..