Freelander 1. Manual - part 103

 

  Index      Land Rover     Freelander 1 - service manual 2002 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  101  102  103  104   ..

 

 

Freelander 1. Manual - part 103

 

 

ENGINE - K SERIES KV6

OVERHAUL 12-3-103

35. Position ancillary belt tensioner, fit bolts and 

tighten to 25 Nm (18 lbf.ft).

36. Clean LH and RH front timing belt covers.
37. Position LH and RH front timing belt covers, fit 

and tighten bolts to 4 Nm (3 lbf.ft).

38. Clean idler pulley, position pulley to engine 

front mounting plate and tighten Torx bolt to 45 
Nm (33 lbf.ft).

39. Position alternator to front mounting plate.
40. Fit bolt and nut and bolt securing alternator to 

front mounting plate and tighten to 45 Nm (33 
lbf.ft).

41. Connect alternator multiplug.
42. Connect battery lead to alternator, fit and 

tighten nut to 8 Nm (6 lbf.ft), fit terminal cover.

43. Clean LH rear timing belt cover.
44. Position LH rear timing belt cover, fit and 

tighten bolts to 4 Nm (3 lbf.ft).

45. Clean RH rear timing belt cover.
46. Position RH rear timing belt cover, fit bolts and 

tighten to4 Nm (3 lbf.ft).

47. Position heat shield, fit bolts and tighten M6 bolt 

to 9 Nm (7 lbf.ft) and M8 bolt to 25 Nm (18 lbf.ft).

48. Fit inlet manifold chamber - if fitted.

 

 + 

 MANIFOLDS & EXHAUST SYSTEMS 

- K SERIES KV6, REPAIRS, Seals - inlet 
manifold chamber.

49. Position ancillary drive belt to crankshaft and 

alternator pulleys.

50. Position engine mounting front bracket to 

engine front plate and tighten bolts to 45 Nm 
(33 lbf.ft).

ENGINE - K SERIES KV6

12-3-104 OVERHAUL

EMISSION CONTROL

ADJUSTMENTS

17-1-1

EMISSION CONTROL 

ADJUSTMENTS

Evaporative loss control system 
(EVAPS) - leak test - NAS

$% 17.90.02.01 

The following procedure allows a fuel leak, indicated 
by the Malfunction Indicator Lamp (MIL), to be 
accurately located. It must only be carried out once it 
has been established that there are no obvious faults 
with any of the system components. 

Check

1. Check components in fuel and EVAP system 

for obvious damage. Ensure all connections 
are properly secured.

2. The system must be checked using a EVAPS 

Diagnostic Testing Station LRA-19-004.

3. Disconnect vent pipe from purge valve and 

connect adapter LRA-19-004/1.

NOTE: The reason for inserting the adapter into 
the purge valve is that there is currently no 
service port fitted to Freelander. 

4. Remove RH rear wheel arch liner.

 

 + 

 EXTERIOR FITTINGS, REPAIRS, 

Liner - rear wheel arch.

5. Release clip and disconnect hose from 

charcoal canister.

CAUTION: Before disconnecting any part of 
the fuel system, it is imperative that all dust, 
dirt and debris is removed from around 
components to prevent ingress of foreign 
matter into fuel system.

6. Block charcoal canister port with bung, 

included in LRA-19-004.

7. Connect LRA-19-004 to service port fitted on 

purge valve.

8. Carry out procedures given in the operating 

instructions, these are supplied with LRA-19-
004
.

Adjust

1. If a leak has been detected, replace component 

as necessary and repeat leak test to validate 
repair.

2. Remove bung from charcoal canister.
3. Connect hose to charcoal canister and secure 

with clip.

4. Fit rear wheel arch liner.

 

 + 

 EXTERIOR FITTINGS, REPAIRS, 

Liner - rear wheel arch.

5. Disconnect adaptor LRA-19-004/1 from purge 

valve.

6. Connect hose to purge valve.

EMISSION CONTROL

17-1-2

ADJUSTMENTS

 

 

 

 

 

 

 

Content   ..  101  102  103  104   ..