Infiniti I30 (A33). Manual - part 558

 

  Index      Infiniti     Infiniti I30 (A33) - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  556  557  558  559   ..

 

 

Infiniti I30 (A33). Manual - part 558

 

 

I30 2001 – Quick Reference – A/T

5

I30 2001

Quick Reference

A/T

PRECAUTIONS

  Before performing any diagnostic test, vehicle should be driven for approximately 10 minutes

to raise transmission to the proper operating temperature of 122

°

 to 176

°

.

  During stall testing, never hold throttle wide open for more than 5 seconds at a time. Extended

stall testing can overheat transmission and cause serious damage.

 Nissan 

Matic 

’D’ ATF is the only fluid accepted for warranty, service contracts and goodwill

repairs.

  Before performing any internal repairs, thoroughly clean the outside of the transmission case

to prevent contamination.

  Use lint free cloth or towels for wiping parts.  Common shop towels can leave contaminating

fibers on the transmission parts and cause improper transmission operation.

  When servicing the valve body, valves, sleeves, plugs, etc. should slide along the bores in the

valve body under their own weight.

  Before assembly, apply a coat of ATF to all internal transmission parts. Use petroleum jelly to

protect o-rings and seals, or to hold bearings and washers in place during assembly.

Important Note: Nissan Matic ’D’ must be used in performing repairs paid by Nissan/Infiniti, such
as warranty, service contract, or good-will repairs. There will not be reimbursement for repairs
when non-genuine Nissan Matic ’D’ is used.

I30 2001 – Quick Reference – Heater & A/C

6

I30 2001

Quick Reference

Heater & A/C

AIR CONDITIONER (AUTO) 

Compressor

Make Calsonic
Type

V-6 Var. Displacement

Compressor Clutch

Disc-to-Pulley Clearance

0.12 - 0.024 in (0.3 - 0.6 mm)

Refrigerant

Type

HFC-134a (R134a)

Capacity

1.43 +/- 0.11 lb.

Refrigerant Oil

Type

Nissan Type “S” Lub

Capacity

7.0 fl oz

Oil to Add Per

Evaporator

2.5 oz (75 ml)

Condenser

2.5 oz (75 ml)

*Liquid Tank

0.2 oz (30ml)

Large Rerig. Leak

1.0 oz (30 ml)

Compressor
(*Add only if comp. Is not replaced.)

Engine Idle w/A/C On

825 rpm or more in Neutral

Performance Test

Recirculating-to-Discharge Air Temp

Recirc. Air Temp. at

Discharge Air Temp. at

Blower Assy. Inlet

Center Ventilator

Relative Humidity

F

°

(C°)

F°(C°)

50 - 60 %

59

°

 (15

°

)

35 - 39

°

 (1.8 - 4.0

°

)

68

°

 (20

°

)

42 - 46

°

 (5.4 - 8.0

°

)

77

°

 (25

°

)

48 - 54

°

 (9.0 - 12.0

°

)

86

°

 (30

°

)

55 - 62

°

 (12.6 - 16.4

°

)

60 - 70 %

59

°

 (15

°

)

39 - 41

°

 (4.0 - 5.0

°

)

68

°

 (20

°

)

46 - 50

°

 (8.0 - 10.0

°

)

77

°

 (25

°

)

48 - 59

°

 (9.0 - 15.0

°

)

86

°

 (30

°

)

55 - 68

°

 (12.6 - 20.0

°

)

Ambient Air Temp-to-Operating Pressure
Air temperature

Relative Humidity 50-70%

F°(C°)

High-pres. PSI

Low-pres. PSI

77

°

 (25

°

)

137 - 164

28 - 43

86

°

 (30

°

)

171 - 203

34 - 50

95

°

 (35

°

)

206 - 246

38 - 57

104

°

 (40

°

)

242 - 293

43 - 63

Thermal Transmitter

Coolant Temp. F°(C°)

Voltage V

104

°

 (40

°

)

Approx. 10.8

131

°

 (55

°

)

Approx. 9.9

140

°

 (60

°

)

Approx. 9.5

I30 2001 – Quick Reference – Heater & A/C

7

Refrigerant Pressure Sensor

Low pressure (at 26 psi) High pressure (at 398 psi)

At 77

°

F (25

°

C)

0.36 V

4.16V

A/C Drive Belt Deflection
Engine Cold

Used Belt

New Belt

Deflection Limit

0.28 in (7 mm)

Deflection After Adj.

0.165 - 0.181 in

0.146 - 0.161

(4.2 - 4.6 mm)

(3.7 - 4.1 mm)

I30 2001 – Quick Reference – Heater & A/C

8

I30 2001

Quick Reference

Heater & A/C

PERFORMANCE TEST CONDITIONS

  Vehicle indoors or in the shade

 Doors 

closed

 Windows 

open

 Hood 

open

  Temperature on "Max" setting

  Mode switch on "Face Vent"

  Recirculation switch on "Recirc"

  Fan speed on "High"

  A/C switch "On" and verify A/C Clutch engagement

  Engine speed at idle

  Verify heater cock is closed

  Operate the A/C system for 10 minutes before taking measurements

Precautions:

1. When removing the compressor, store it in the same position as it is mounted in the vehicle.

Failure to do so may cause lubricant to enter the low pressure chamber and cause compressor
damage.

2. Allow components stored in cool areas to warm to area temperatures before removing seals.

This prevents condensation from forming inside A/C components.

 

 

 

 

 

 

 

Content   ..  556  557  558  559   ..