Hyundai Getz: Body Repair Manual - part 33

138

SECTION D-D'

SECTION A-A'

SECTION C-C'

Under body  coating (Thickness 0.8 mm - 2.0 mm)

CORROSION PROTECTION - Under  body coat

TB-134

SECTION B-B'

Because parts are to be mounted in these locations, mask the location, before applying
the under body coat.

134-1

134-2

134-3

134-4

A

A'

C'

C

Í

Í

B

B'

D'











UNDER BOD

UNDER BOD

UNDER BOD

UNDER BOD

UNDER BODY CO

Y CO

Y CO

Y CO

Y COA

A

A

A

AT

T

T

T

T

In order to provide corrosion,   stone chipping and vibration resistance, under body coat is applied to the under sides of the
floor  and wheel house.
Therefore, when such  panel is replaced or repaired, apply under body coat to that part.

FLOOR

D

Í

Í

Í

Í

Í

Í

Side outer panel

Center floor panel

Center floor side
member

Center floor panel

Center floor side
member

Rear floor panel

70mm

ø

 50 must be masking

ø

 60 must be masking

60mm

Rear floor extension

Center floor panel

Rear floor panel

Rear floor front
member

Side sill inner panel

139

SIDE BOD

SIDE BOD

SIDE BOD

SIDE BOD

SIDE BODY

Y

Y

Y

Y

SECTION A-A'

CORROSION PROTECTION - Under body coat

135-1

SECTION B-B'

A

A'

ΠΠΠΠÎ

ΠΠΠΠÎ

ΠΠΠΠÎ

ΠΠΠΠÎ

135-2

TB-135

Because parts are to be mounted in these locations, mask the location before applying
the under body coat.

Under body  coating (Thickness 1.0 mm - 2.0 mm)











B'

B









































Front shock absorber
cover panel

Fender apron
upper member

Front apron inner panel

Front side inner
panel

Front side outer panel

Rear spring cover bracket

Wheel house inner panel

Rear floor panel

Rear floor side
member

30mm

Side outer
panel

Quarter inner panel, LH

Fender apron upper
reinforcement

140

VIEW "B"

CAVITY WAX INJECTION

In order to provide greater corrosion resistance, cavity wax injection has been performed for the lower areas of the
vehicle, such as the sidemember, the side sill and the inside of other panels which are a hollow construction.
When replacing these parts, be such to apply cavity wax to the appropriate areas of the new parts.

CORROSION PROTECTION - Cavity wax injection

SECTION A-A'

VIEW "C"

Wax injection must be done through access holess marked.



COR-0031

COR-0033

COR-0030

50mm

Cavity wax injection (Thickness 40 

µ

 - 50

µ

)

A

Ï

A'

(MIN)

Ï































COR-0032

"B"

Ï

"C"

Ï

ø 

13mm

141

CORROSION PROTECTION - Cavity wax injection

SECTION A-A'

SECTION B-B'

Wax injection must be done through access holes marked.



COR-0041

COR-0051

COR-0040/0050

Cavity wax injection (Thickness 40

µ

 - 50

µ

)

SECTION C-C'

COR-0052

30mm



Í

Í

A

A'





B

B'

Í





150mm

HOOD

TAIL GATE

30mm

(MIN)

200mm 250mm



200mm 250mm



Í

(MIN)

150mm (MIN)

(MIN)

5mm
(MIN)

5mm

(MIN)