Geely EC718, EC718RV, EC715, EC715RV. Manual part

2.2.3 System Working Principle
2.2.3.1 System Working Principle

ECM calculates the basic fuel injection duration, Air-Fuel ratio
close to the ideal mixture for the engine, and controls engine
operation based on the engine's intake air quantity and engine
speed signal. For example, in cold start, according to related
signals,  ECM  increases  the  fuel  injection  and  controls  idle
speed  control  valve  actuator,  to  achieve  a  smooth  start  and
controls the engine idle speed. In addition, ECM also has the
fault self-diagnosis and protection function, when the engine
fails, ECM can automatically diagnose and preserve the DTC
code and, sends a warning through the fault indicator light. The
stored  code  can  appear  again  in  certain  trigger  conditions.
Once the sensor or actuator fail, ECM automatically start the
backup system, to ensure the safety of the vehicle, maintain
the  vehicle  driving  ability.  ECM  can  also  communicate  with
scan tool. Scan tool can be used to read the stored DTC code
and scan the current ECM operating system parameters, that
is  the  data  stream.  Scan  tool  can  also  be  used  to  drive  the
control  system  actuators  for  test,  which  provides  a  great
convenience to diagnostic.

2.2.3.2 Fuel Injection Quantity Adjustment

At  Startup,  ECM  calculates  fuel  injection  time  based  on  the
engine speed, engine coolant temperature signal. After startup,
ECM determines the basic fuel injection quantity based on the
intake  manifold  absolute  pressure  sensor.  After  determining
the  basic  fuel  injection  quantity,  according  to  the  different
engine operating conditions, ECM adjusts the fuel injection as
following:

–

Start Up-Enrich Mixture: Starting condition is when the
engine speed is below the specified value, the ignition
switch is ON. Especially in the low temperature, in order to
improve startup performance, ECM increases fuel injection
time, and enriches the mixture.

–

After Start-Enrich Mixture: The engine has just started, in
order to maintain its running stability, ECM increases fuel
injection amount according to the engine coolant
temperature.

–

Warm Up-Enrich Mixture: The engine temperature is low,
gasoline evaporation is poor, ECM provides rich mixture.
ECM increases fuel injection amount according to the
engine coolant temperature.

–

Heavy  Load-Enrich  Mixture:  The  engine  power  output  is
maximum,  in  order  to  ensure  the  engine  work  properly,
ECM increases fuel injection duration according to throttle
position,  engine  speed,  air  flow,  engine  coolant
temperature  signal.  Increased  fuel  amount  is  up  to  8%
-30% of normal fuel injection amount.

–

Acceleration-Enrich  Mixture:  When  the  engine  is
accelerating,  for  it  to  have  dynamic,  enrich  the  mixture.
ECM  increase  the  fuel  injection  amount  according  to  air
flow, engine speed, vehicle speed, throttle position (change
rate), the engine coolant temperature sensor signal.

–

Intake Air Temperature Adjustment: Air density changes as
the  temperature  changes.  In  order  to  maintain  a  more
accurate  Air-Fuel  ratio,  ECM  uses  air  density  at  20°C
(68 ºF) as the standard value. ECM adjusts fuel injection
according to measured intake air temperature signal. At low
temperature, ECM increases fuel injection amount. At high
temperature,  ECM  decreases  fuel  injection  amount.  The
adjustment is up to 10%.

–

idle  Stability  Adjustment:  In  the  engine  control  system,
when the intake manifold pressure increase, the idle speed
drops.  ECM  adjusts  fuel  injection  amount  according  to
throttle  position,  engine  speed,  intake  manifold  absolute
pressure sensor signal.

–

Air-Fuel Ratio Feedback Adjustment: ECM adjusts fuel
injection amount according to oxygen sensor signal. When
engine starts, the mixture will be enriched. With heavy load,
the engine coolant temperature below the set temperature
and fuel supply cut off operating conditions, ECM is in
close-loop control mode.

–

Cut Off Fuel Supply: In order to achieve good fuel economy,
lower emissions pollution, when the engine is in forced idle
state, ECM cut off fuel supply temporarily according to
throttle position, engine speed, engine coolant temperature
sensor signal. During emergency deceleration, engine over
speed, vehicle over speed, fuel supply will also be cut off
temporarily.

–

Voltage Adjustment: Power supply voltage affects fuel
injection amount. When voltage is low, the actual injection
duration is shorter than normal and the mixture is lean. It
needs to be adjusted. ECM adjusts fuel injection amount
according to high or low voltage. Power supply voltage
signal is from the battery.

Engine

Control System JL4G18-D

2-23

2.2.3.3 Fault Self-Diagnostic and Protection
Function

In order to discover the engine electronically controlled
gasoline injection system fault in time, and maintain the vehicle
basic driving ability when a fault occurs, ECM has a fault
diagnostic and self-protection function. ECM is equipped with
a dedicated self-diagnostic circuit. When the engine is running,
ECM continuous monitors various parts. Once ECM detects an
abnormal situation, it will store the fault signal in memory, and
displays DTC code.

In order to prevent vehicle can not be driven due to the sensor
malfunction. ECM uses pre-stored sensor signals to continue
to control engine operation.

For actuators, in order to prevent their failure affect safety, ECM
can take measures to ensure the engine safety. At this point,
ECM will send out warning signals and stop fuel injection.

In addition, ECM is also equipped with an emergency circuit.
When the emergency control circuit receives an abnormal
signal, ECM will enable the backup program. The fuel injection
amount and ignition timing will be controlled according to the
original set-up program, to maintain the vehicle basic driving
ability.

2-24

Control System JL4G18-D

Engine