Ford GT (2018 year). Manual - part 14

GENERAL INFORMATION

Condensation in the Exterior Front
Lamps and Rear Lamps

Exterior front lamps and rear lamps have
vents to accommodate normal changes
in air pressure.

Condensation can be a natural by-product
of this design. When moist air enters the
lamp assembly through the vents, there is
a possibility that condensation can occur
when the temperature is cold. When
normal condensation occurs, a fine mist
can form on the interior of the lens. The
fine mist eventually clears and exits
through the vents during normal operation.

Clearing time may take as long as 48 hours
under dry weather conditions.

Examples of acceptable condensation are:
•

The presence of a fine mist (no streaks,
drip marks or large droplets).

•

A fine mist covers less than 50% of the
lens.

Examples of unacceptable condensation
are:
•

A water puddle inside the lamp.

•

Streaks, drip marks or large droplets
present on the interior of the lens.

If you see any unacceptable condensation,
have your vehicle checked by an authorized
dealer.

LIGHTING CONTROL

E252122

Off.

A

Parking lamps, instrument panel
lamps, license plate lamps and
rear lamps.

B

Headlamps.

C

Autolamps.

D

High Beams

E227823

High beam control.

A

Press the button briefly to flash the high
beams.

Press and hold to switch the high beams
on.

Press and hold again to switch the high
beams off.

AUTOLAMPS

WARNING

The system does not relieve you of
your responsibility to drive with due
care and attention. You may need to

override the system if it does not turn the
headlamps on in low visibility conditions,
for example daytime fog.

E142451

When the lighting control is in the
autolamps position, the headlamps turn
on in low light situations, or when the
wipers turn on.

The headlamps remain on for a period of
time after you switch the ignition off.  Use
the information display controls to adjust
the period of time that the headlamps
remain on.

Note:  If you switch on the autolamps, you
cannot switch the high beams on until the
system turns the low beams on.

INSTRUMENT LIGHTING
DIMMER

Note: If you disconnect the battery or it
becomes discharged, the illuminated
components turn to the maximum setting.

E236438

Press repeatedly or press and
hold to brighten.

A

Press repeatedly or press and
hold to dim.

B

DAYTIME RUNNING LAMPS

WARNING

The daytime running lamps system
does not activate the rear lamps and
may not provide adequate lighting

during low visibility driving conditions.
Make sure you switch the headlamps on,
as appropriate, during all low visibility
conditions. Failure to do so may result in a
crash.

To switch the system on:
•

For vehicles sold in the United States,
the lighting control must be in the
autolamps position. The lamps turn on
in daylight and turn the headlamps on
when ambient light is low. You can
enable this feature in the information
display.  See Information Displays
(page 70).

•

For vehicles sold in Canada, daytime
running lamps turn on in both off and
autolamps position. You cannot
disable this feature.

DIRECTION INDICATORS

E229691

Left direction indicator.

A

Right direction indicator.

B

Note: The direction indicator buttons are
on the steering wheel.

Press and hold the button briefly to use
the direction indicators.

Press the button briefly to flash the
indicator three times.

INTERIOR LAMPS

 (If Equipped)

Note: The interior lamp switch is on the
overhead console.

The lamps turn on under the following
conditions:
•

You open any door.

•

You press the panic button on the
remote control.

•

You press the lamp button.

E187345

POWER WINDOWS

WARNINGS

Do not leave children unattended in
your vehicle and do not let them play
with the power windows. Failure to

follow this instruction could result in
personal injury.

When closing the power windows,
verify they are free of obstruction and
make sure that children and pets are

not in the proximity of the window
openings.

E146043

Note: You may hear a pulsing noise when
just one of the windows is open. Lower the
opposite window slightly to reduce this
noise.

Press the switch to open the window.

Lift the switch to close the window.

One-Touch Down

Press the switch fully and release it. Press
again or lift it to stop the window.

One-Touch Up

Lift the switch fully and release it. Press or
lift it again to stop the window.

Bounce-Back

The window will stop and reverse some
distance if it detects an obstacle while
closing.

Overriding the Bounce-Back Feature

WARNING

If you override bounce-back, the
window does not reverse if it detects
an obstacle. Take care when closing

the windows to avoid personal injury or
damage to your vehicle.

Pull up the window switch and hold within
two seconds of the window reaching the
bounce-back position. The window will
travel up with no bounce-back protection.
The window will stop if you release the
switch before the window is fully closed.

Accessory Delay

You can use the window switches for
several minutes after you switch the
ignition off or until you open either front
door.

GLOBAL OPENING

You can use the remote control to open
the windows with the ignition off.

Note: You can enable or disable this feature
in the information display, or see an
authorized dealer.  See General
Information (page 70).

Note: To operate this feature, accessory
delay must not be active.