Dodge Challenger (2022 year). Manual in english

GETTING TO KNOW YOUR VEHICLE



To operate HomeLink®, push and release any

of the programmed HomeLink® buttons. These

buttons will activate the devices they are

programmed to with each press of the corre

sponding HomeLink® button.



The HomeLink® indicator light is located above

the center button.

NOTE:

HomeLink® is disabled when the Vehicle Security

system is active

page 322.

EFORE

EGIN

ROGRAMMING

OME

INK

For efficient programming and accurate

transmission of the Radio Frequency (RF) signal, it

is recommended that a new battery be placed in

the hand-held transmitter of the device that is

being programmed to the HomeLink® system.

Make sure your hand-held transmitter is

programmed to activate the device you are trying

to program your HomeLink® button to.
Ensure that your vehicle is parked outside of the

garage before you begin programming.
It is recommended that you erase all the channels

of your HomeLink® before you use it for the first

time.

RASING

OME

INK

HANNELS

To erase the channels, follow this procedure:
1. Place the ignition switch into the ON/RUN

position.

2. Push and hold the two outside HomeLink®

buttons (I and III) for up to 20 seconds, or until

the HomeLink® indicator light flashes.

NOTE:

Erasing all channels should only be performed

when programming HomeLink® for the first time.

Do not erase channels when programming addi

tional buttons.

DENTIFYING

HETHER

AVE

OLLING

ODE

-R

OLLING

ODE

EVICE

Before programming a device to one of your

HomeLink® buttons, you must determine whether

the device has a rolling code or non-rolling code.

Rolling Code Devices
To determine if your device has a rolling code, a

good indicator is its manufacturing date. Typically,

devices manufactured after 1995 have rolling

codes. A device with a rolling code will also have a

“LEARN” or “TRAIN” button located where the

antenna is attached to the device. The button may

not be immediately visible when looking at the

device. The name and color of the button may vary

slightly by manufacturer.

NOTE:

The “LEARN” or “TRAIN” button is not the button

you normally use to operate the device.
Non-rolling Code Devices
Most devices manufactured before 1995 will not

have a rolling code. These devices will also not

have a “LEARN” or “TRAIN” button.

GETTING TO KNOW YOUR VEHICLE

ROGRAMMING

OME

INK

® T

ARAGE

OOR

PENER

To program any of the HomeLink® buttons to

activate your garage door opener motor, follow the

steps below:

NOTE:

All HomeLink® buttons are programmed using this

procedure. You do not need to erase all channels

when programming additional buttons.
1. Place the ignition switch into the ON/RUN

position.

2. Place the garage door opener transmitter

1 to 3 inches (3 to 8 cm) away from the

HomeLink® button you wish to program, while

keeping the HomeLink® indicator light in view.

3. Push and hold the HomeLink® button you

want to program while you push and hold the

garage door opener transmitter button you are

trying to replicate.

4. Continue to hold both buttons and observe the

HomeLink® indicator light. The HomeLink®

indicator light will flash slowly and then rapidly.

Once this happens, release both buttons.

NOTE:

Make sure the garage door opener motor is

plugged in before moving on to the rolling code/

non-rolling code final steps.

Rolling Code Garage Door Opener Final Steps

NOTE:

You have 30 seconds in which to initiate rolling

code final step 2, after completing rolling code

final step 1.
1. At the garage door opener motor (in the

garage), locate the “LEARN” or “TRAIN”

button. This can usually be found where the

hanging antenna wire is attached to the

garage door opener motor. Firmly push and

release the “LEARN” or “TRAIN” button.

2. Return to the vehicle and push the

programmed HomeLink® button three times

(holding the button for two seconds each

time). If the garage door opener motor

operates, programming is complete.

3. Push the programmed HomeLink® button to

confirm that the garage door opener motor

operates. If the garage door opener motor

does not operate, repeat the final steps for the

rolling code procedure.

Non-Rolling Code Garage Door Opener Final Steps
1. Push and hold the programmed HomeLink®

button and observe the HomeLink® indicator

light. If the HomeLink® indicator light stays

on constantly, programming is complete.

2. Push the programmed HomeLink® button to

confirm that the garage door opener motor

operates. If the garage door opener motor

does not operate, repeat the steps from the

beginning.

ROGRAMMING

OME

INK

® T

ISCELLANEOUS

EVICE

The procedure on how to program HomeLink® to a

miscellaneous device follows the same procedure

as programming to a garage door opener

page 42. Be sure to determine if the device has

a rolling code, or non-rolling code before beginning

the programming process.

WARNING!



Your motorized door or gate will open and

close while you are programming the universal

transceiver. Do not program the transceiver if

people or pets are in the path of the door or

gate.



Do not run your vehicle in a closed garage or

confined area while programming the trans

ceiver. Exhaust gas from your vehicle contains

Carbon Monoxide (CO) which is odorless and

colorless. Carbon Monoxide is poisonous

when inhaled and can cause you and others to

be severely injured or killed.

GETTING TO KNOW YOUR VEHICLE

NOTE:

Canadian Radio Frequency (RF) laws require trans

mitter signals to time-out (or quit) after several

seconds of transmission, which may not be long

enough for HomeLink® to pick up the signal during

programming. Similar to this Canadian law, some

U.S. gate operators are designed to time-out in the

same manner. The procedure may need to be

performed multiple times to successfully pair the

device to your HomeLink® buttons.

EPROGRAMMING

A S

INGLE

OME

INK

® B

UTTON

To reprogram a single HomeLink® button that has

been previously trained, without erasing all the

channels, follow the procedure below. Be sure to

determine whether the new device you want to

program the HomeLink® button to has a rolling

code, or non-rolling code.
1. Place the ignition in the ON/RUN position,

without starting the engine.

2. Push and hold the desired HomeLink® button

until the HomeLink® indicator light begins to

flash after 20 seconds. Do not release the

button.

3. Without releasing the button, proceed with

Step 2 in “Programming HomeLink® To A

Garage Door Opener” and follow all remaining

steps.

ANADIAN

ATE

PERATOR

ROGRAMMING

For programming transmitters in Canada/United

States that require the transmitter signals to

“time-out” after several seconds of transmission:
Canadian Radio Frequency (RF) laws require

transmitter signals to time-out (or quit) after

several seconds of transmission, which may not be

long enough for HomeLink® to pick up the signal

during programming. Similar to this Canadian law,

some U.S. gate operators are designed to time-out

in the same manner.
It may be helpful to unplug the device during the

cycling process to prevent possible overheating of

the garage door or gate motor.
1. Place the ignition in the ON/RUN position.

NOTE:

For vehicles equipped with Keyless Enter ‘n Go™,

place the ignition in the RUN position. Make sure

while programming HomeLink® with the engine on

that your vehicle is outside of your garage, or that

the garage door remains open at all times.
2. Place the hand-held transmitter 1 to 3 inches

(3 to 8 cm) away from the HomeLink® button

you wish to program while keeping the

HomeLink® indicator light in view.

3. Continue to push and hold the HomeLink®

button while you push and release (cycle) your

hand-held transmitter every two seconds until

HomeLink® has successfully accepted the

frequency signal. The indicator light will flash

slowly and then rapidly when fully trained.

4. Watch for the HomeLink® indicator to change

flash rates. When it changes, it is

programmed. It may take up to 30 seconds or

longer in rare cases. The garage door may

open and close while you are programming.

5. Push and hold the programmed HomeLink®

button and observe the indicator light.

NOTE:



If the indicator light stays on constantly,

programming is complete and the garage

door/device should activate when the

HomeLink® button is pushed.



To program the two remaining HomeLink®

buttons, repeat each step for each

remaining button. DO NOT erase the chan

nels.

If you unplugged the garage door opener/device

for programming, plug it back in at this time.

GETTING TO KNOW YOUR VEHICLE

Reprogramming A Single HomeLink® Button

(Canadian/Gate Operator)
To reprogram a channel that has been previously

trained, follow these steps:
1. Place the ignition in the ON/RUN position.
2. Press and hold the desired HomeLink® button

until the indicator light begins to flash after

20 seconds. Do not release the button.

3. Without releasing the button, proceed with

“Canadian/Gate Operator Programming”

Step 2 and follow all remaining steps.

ECURITY

It is advised to erase all channels before you sell or

turn in your vehicle.
To do this, push and hold the two outside buttons

for 20 seconds until the indicator flashes. Note

that all channels will be erased. Individual

channels cannot be erased.
The HomeLink® Universal Transceiver is disabled

when the Vehicle Security system is active.

ROUBLESHOOTING

IPS

If you are having trouble programming

HomeLink®, here are some of the most common

solutions:



Replace the battery in the garage door opener

hand-held transmitter.



Push the LEARN button on the garage door

opener to complete the training for a rolling

code.



Did you unplug the device for programming and

remember to plug it back in?

If you have any problems, or require assistance,

please call toll-free 1-800-355-3515 or, on the

Internet at

HomeLink.com

for information or

assistance.

EXTERIOR LIGHTS

EADLIGHT

WITCH

The headlight switch is located on the left side of

the instrument panel. This switch controls the

operation of the headlights, parking lights,

instrument panel lights, instrument panel light

dimming, interior lights and fog lights (if equipped).

Headlight Switch

WARNING!



Vehicle exhaust contains carbon monoxide, a

dangerous gas. Do not run your vehicle in the

garage while programming the transceiver.

Exhaust gas can cause serious injury or death.



Your motorized door or gate will open and

close while you are programming the universal

transceiver. Do not program the transceiver if

people, pets or other objects are in the path of

the door or gate. Only use this transceiver with

a garage door opener that has a “stop and

reverse” feature as required by Federal safety

standards. This includes most garage door

opener models manufactured after 1982. Do

not use a garage door opener without these

safety features.

1 — Rotate Headlight Control
2 — Push Fog Light Control
3 — Instrument Panel Dimmer Control
4 — Ambient Light Dimmer Control

GETTING TO KNOW YOUR VEHICLE

Headlight Switch (Vehicles Sold In Canada Only)

NOTE:

Vehicles sold in Canada are equipped with a head

light switch without the OFF position. In order to

turn the exterior lights off, the headlight switch

must be rotated to AUTO position.
To turn on the headlights, rotate the headlight

switch clockwise. When the headlight switch is on,

the parking lights, taillights, license plate light and

instrument panel lights are also turned on. To turn

off the headlights, rotate the headlight switch back

to the O (off) position.

NOTE:

For vehicles sold in Canada, rotate the headlight

switch clockwise from the parking lights and

instrument panel lights position to the first detent

to turn the headlight switch to the AUTO position.

Rotate to the second detent to turn on headlights,

parking lights, and instrument panel lights oper

ation.

ULTIFUNCTION

EVER

The multifunction lever is located on the left side of

the steering column.

Multifunction Lever

AYTIME

UNNING

IGHTS

(DRL

) —

QUIPPED

The Daytime Running Lights will turn on when the

engine is started and will remain on unless the

headlamps are turned to the on position, the

parking brake is applied, or the ignition is placed in

the OFF position.

NOTE:



For vehicles sold in Canada, the Daytime

Running Lights will automatically deactivate

when the front fog lights are turned on.



If allowed by law in the country in which the

vehicle was purchased, the Daytime Running

Lights can be turned on and off using the Ucon

nect system

page 123.



On some vehicles, the Daytime Running Lights

may deactivate, or reduce intensity, on one side

of the vehicle (when a turn signal is activated on

that side), or on both sides of the vehicle (when

the hazard warning lights are activated).

IGH

EAM

WITCH

Push the multifunction lever toward the instrument

panel to switch the headlights to high beams.

Pulling the multifunction lever back will turn the

low beams on.

UTOMATIC

IGH

EAM

EADLAMP

ONTROL

— I

QUIPPED

The Automatic High Beam Headlamp Control

system provides increased forward lighting at night

by automating high beam control through the use

of a camera mounted on the windshield. This

camera detects vehicle specific light and

automatically switches from high beams to low

beams until the approaching vehicle is out of view.

1 — Rotate Headlight Control
2 — Push Fog Light Control
3 — Instrument Panel Dimmer Control
4 — Ambient Light Dimmer Control

GETTING TO KNOW YOUR VEHICLE

NOTE:



The Automatic High Beam Headlamp Control

can be turned on or off using the Uconnect

system

page 123.



Broken, muddy, or obstructed headlights and

taillights of vehicles in the field of view will

cause headlights to remain on longer (closer to

the vehicle). Also, dirt, film, and other obstruc

tions on the windshield or camera lens will

cause the system to function improperly.



To opt out of the Advanced Auto High-Beam

Sensitivity Control and enter Reduced

High-Beam Sensitivity Control (not recom

mended), toggle the high beam lever six full

on/off cycles within 10 seconds of placing the

ignition in the ON position. The system will

return to the default setting upon placing the

ignition in the OFF position.



If the windshield or Automatic High Beam Head

lamp Control mirror is replaced, the mirror must

be re-aimed to ensure proper performance. See

a local authorized dealer.

LASH

-T

-P

ASS

You can signal another vehicle with your headlights

by lightly pulling the multifunction lever toward you.

This will cause the high beam headlights to turn on,

and remain on, until the lever is released.

NOTE:

If the multifunction lever is held in the flash-to pass

position for more than 20 seconds, the high beams

will shut off.

UTOMATIC

EADLIGHTS

This system automatically turns the headlights on

or off according to ambient light levels. To turn the

system on, rotate the headlight switch

counterclockwise to the AUTO position.
When the system is on, the Headlight Delay feature

is also on. This means the headlights will stay on

for up to 90 seconds after you place the ignition

into the OFF position. To turn the automatic

headlights off, turn the headlight switch out of the

AUTO position.

NOTE:

The engine must be running before the headlights

will come on in the automatic mode.

ARKING

IGHTS

To turn on the parking lights and instrument panel

lights, rotate the headlight switch clockwise. To

turn off the parking lights, rotate the headlight

switch back to the O (off) position.

NOTE:

For vehicles sold in Canada, rotate the headlight

switch to the AUTO position to turn off the parking

lights.

UTOMATIC

EADLIGHTS

ITH

IPERS

If your vehicle is equipped with Automatic

Headlights, it also has this

customer-programmable feature. When your

headlights are in the automatic mode and the

engine is running, they will automatically turn on

when the wiper system is on. This feature is

programmable through the Uconnect system

page 123.

In addition, the headlights will turn off when the

wipers are turned off if they were turned on by this

feature.

GETTING TO KNOW YOUR VEHICLE

EADLIGHT

IME

ELAY

To assist when exiting the vehicle, the headlight

delay feature will leave the headlights on for up to

90 seconds. This delay is initiated when the

ignition is placed in the OFF position while the

headlight switch is on, and then the headlight

switch is cycled off within 45 seconds. Headlight

delay can be cancelled by either turning the

headlight switch on then off, or by placing the

ignition in the ON position.

NOTE:



This feature can be programmed through the

Uconnect system

page 123.



If you turn the headlights off before the ignition,

they will turn off in the normal manner.

IGHTS

-O

EMINDER

If the headlights or parking lights are on after the

ignition is placed in the OFF position, the vehicle

will chime when the driver's door is opened.

IGHTS

— I

QUIPPED

To activate the front fog lights, turn on the parking

lights or the low beam headlights, and push the fog

light button on the headlight switch.

Fog Light Switch

Fog Light Switch (Vehicles Sold In Canada Only)

The fog lights will operate only when the parking

lights are on or when the vehicle headlights are on

low beam. An indicator light located in the

instrument cluster will illuminate when the fog

lights are on. The fog lights will turn off when the

switch is pushed a second time, when the

headlight switch is rotated to the off position, or

the high beam is selected.

URN

IGNALS

Move the multifunction lever up or down to

activate the turn signals. The arrows on each side

of the instrument cluster flash to show proper

operation.

NOTE:



If either light remains on and does not flash, or

there is a very fast flash rate, check for a defec

tive outside light bulb.



A “Turn Signal On” message will appear in the

instrument cluster display and a continuous

chime will sound if the vehicle is driven more

than 1 mile (1.6 km) with either turn signal on.

ANE

HANGE

SSIST

— I

QUIPPED

Lightly push the multifunction lever up or down,

without moving beyond the detent, and the turn

signal will flash three times then automatically turn

off.

GETTING TO KNOW YOUR VEHICLE

INTERIOR LIGHTS

The interior lights come on when a door is opened.
To protect the battery, the interior lights will turn off

automatically 10 minutes after the ignition is

placed in the OFF position. This will occur if the

interior lights were switched on manually or are on

because a door is open. The Battery Protection

also includes the glove compartment light and the

trunk light. To restore interior light operation after

automatic battery protection is enabled (lights off),

either place the ignition in the ON/RUN position or

cycle the light switch.

RONT

EADING

IGHTS

These lights are mounted between the sun visors

on the overhead console. Each light is turned on by

pushing the lens. Push the lens a second time to

turn off the light. These lights also turn on when a

door is opened, when the unlock button on the

remote keyless entry key fob is pushed, or when

the dimmer control is turned fully upward, to the

second detent.

Map/Reading Lights

MBIENT

IGHT

— I

QUIPPED

The overhead console is equipped with an ambient

light feature. This light casts illumination for

improved visibility of the floor and center console

area.
Rotate the right dimmer control upward or

downward to increase or decrease the brightness

of the door handle lights, map pocket lights, and

ambient light located in the overhead console.

Door Handle/Ambient Light Dimmer

(Vehicles Sold In Canada Only)

GETTING TO KNOW YOUR VEHICLE

IMMER

ONTROLS

The dimmer control is part of the headlight switch

and is located on the left side of the instrument

panel.
With the parking lights or headlights on, rotating

the left dimmer control upward will increase the

brightness of the instrument panel lights and

lighted cupholders (if equipped).

Instrument Panel Dimmer

Instrument Panel Dimmer (Vehicles Sold In Canada Only)

Rotate the instrument panel dimmer control

downward to the O (off) position, and the interior

lights will remain off when the doors are open.
Rotate the instrument panel dimmer control

upward to the first detent to brighten all text

displays such as the odometer, instrument cluster

display, and radio when the parking lights or

headlights are on. Rotating the instrument panel

dimmer control completely upward to the second

detent will turn on the interior lights. The interior

lights will remain on when the dimmer control is in

this position.

LLUMINATED

NTRY

The courtesy lights will turn on when you use the

key fob to unlock the doors or open any door.
The lights will fade to off after approximately

30 seconds, or they will immediately fade to off

once the ignition switch is placed in the ON/RUN

position from the OFF position.
The courtesy lights will not turn off if the instrument

panel dimmer control is rotated upward to the

second detent. The courtesy lights will turn off after

10 minutes when the ignition is placed in the OFF

position to protect the battery.
The illuminated entry system will not operate if the

instrument panel dimmer control is rotated all the

way down to the O (off) position.

GETTING TO KNOW YOUR VEHICLE

(Continued)

WINDSHIELD WIPERS AND WASHERS

The windshield wiper/washer controls are located

on the multifunction lever on the left side of the

steering column. The multifunction lever operates

the windshield wipers and washer when the

ignition is placed in the ACC or ON/RUN position.

Windshield Wiper/Washer Control

INDSHIELD

IPER

PERATION

Rotate the end of the multifunction lever to the first

detent, past the intermittent settings for low-speed

wiper operation, or to the second detent past the

intermittent settings for high-speed wiper

operation.

Intermittent Wipers
Rotate the end of the multifunction lever to the first

detent position, and then turn the end of the lever

to select the desired delay interval. There are four

delay settings, which allow you to regulate the wipe

interval from a minimum of one cycle every second

to a maximum of approximately 36 seconds

between cycles. The delay intervals will double in

duration when the vehicle speed is 10 mph

(16 km/h) or less.
Windshield Washers
To use the washer, push the multifunction lever

inward (toward the steering wheel) and hold. If the

lever is pushed while in the intermittent setting,

the wipers will turn on and operate for two cycles

after the end of the lever is released, and then

resume the intermittent interval previously

selected.
If the end of the lever is pushed while the wipers

are in the off position, the wipers will operate for

three wipe cycles and then turn off.

Mist
Rotate the end of the lever downward to the MIST

position and release for a single wiping cycle. The

wipers will continue to operate until you release

the multifunction lever

NOTE:

The Mist feature does not activate the washer

pump; therefore, no washer fluid will be sprayed on

the windshield. The wash function must be used in

order to spray the windshield with washer fluid.
For information on wiper care and replacement,

see

page 268.

1 — Push End Inward For Washer
2 — Rotate For Front Wiper Operation And Mist

WARNING!

Sudden loss of visibility through the windshield

could lead to a collision. You might not see other

vehicles or other obstacles. To avoid sudden

icing of the windshield during freezing weather,

warm the windshield with the defroster before

and during windshield washer use.

CAUTION!



Turn the windshield wipers off when driving

through an automatic car wash. Damage to

the windshield wipers may result if the wiper

control is left in any position other than off.



In cold weather, always turn off the wiper

switch and allow the wipers to return to the

park position before turning off the engine. If

the wiper switch is left on and the wipers

freeze to the windshield, damage to the wiper

motor may occur when the vehicle is

restarted.

GETTING TO KNOW YOUR VEHICLE

AIN

ENSING

IPERS

— I

QUIPPED

This feature senses rain or snowfall on the

windshield and automatically activates the wipers.

Rotate the end of the multifunction lever to one of

four settings to activate this feature.
The sensitivity of the system can be adjusted with

the multifunction lever. Wiper delay position 1 is

the least sensitive, and wiper delay position 4 is

the most sensitive.
Wiper delay position three should be used for

normal rain conditions.

NOTE:



The Rain Sensing feature will not operate when

the wiper switch is in the low or high-speed posi

tion.



The Rain Sensing feature may not function prop

erly when ice, or dried salt water is present on

the windshield.



Use of Rain-X or products containing wax or sili

cone may reduce Rain Sensing performance.



The Rain Sensing feature can be turned on and

off using the Uconnect system

page 123.

The Rain Sensing system has protection features

for the wiper blades and arms, and will not operate

under the following conditions:



Low Ambient Temperature — When the ignition

is first placed in the ON position, the Rain

Sensing system will not operate until the wiper

switch is moved, vehicle speed is greater than

0 mph (0 km/h), or the outside temperature is

greater than 32°F (0°C).



Transmission In NEUTRAL Position — When the

ignition is ON, and the transmission is in the

NEUTRAL position, the Rain Sensing system will

not operate until the wiper switch is moved,

vehicle speed is greater than 3 mph (5 km/h),

or the gear selector is moved out of the

NEUTRAL position.



Remote Start Mode Inhibit — On vehicles

equipped with the Remote Start system, Rain

Sensing wipers are not operational when the

vehicle is in the Remote Start mode.

CLIMATE CONTROLS

The Climate Control system allows you to regulate

the temperature, air flow, and direction of air

circulating throughout the vehicle. The controls are

located on the touchscreen (if equipped) and on

the instrument panel below the radio.

UTOMATIC

LIMATE

ONTROL

ESCRIPTIONS

UNCTIONS

Uconnect 4 With 7-inch Display Automatic

Climate Controls



Always remove any buildup of snow that

prevents the windshield wiper blades from

returning to the off position. If the windshield

wiper control is turned off and the blades

cannot return to the off position, damage to

the wiper motor may occur.

CAUTION!

GETTING TO KNOW YOUR VEHICLE

Uconnect 4C/4C NAV With 8.4-inch Display Automatic

Climate Controls

MAX A/C Button

Press and release the MAX A/C button on

the touchscreen to change the current

setting to the coldest output of air. The

MAX A/C indicator illuminates when

MAX A/C is on. Pressing and releasing the button

again will cause the MAX A/C operation to exit.

NOTE:

The MAX A/C button is only available on the touch

screen.

A/C Button

Press and release this button on the

touchscreen, or push the button on the

faceplate to change the current setting.

The A/C indicator illuminates when A/C is

ON.

The Air Conditioning (A/C) button allows the

operator to manually activate or deactivate the air

conditioning system. When the air conditioning

system is turned on, cool dehumidified air will flow

through the outlets into the cabin.

NOTE:



If fog or mist appears on the windshield or side

glass, select Defrost mode, and increase blower

speed if needed.



If your air conditioning performance seems

lower than expected, check the front of the A/C

condenser (located in front of the radiator), for

an accumulation of dirt or insects. Clean with a

gentle water spray from the front of the radiator

and through the condenser.

Recirculation Button

Press and release this button on the

touchscreen, or push the button on the

faceplate to change the system between

recirculation mode and outside air mode.

The Recirculation indicator and the A/C indicator

illuminate when the Recirculation button is

pressed. Recirculation can be used when outside

conditions such as smoke, odors, dust, or high

humidity are present. Recirculation can be used in

all modes. Recirculation may be unavailable

(button on the touchscreen greyed out) if

conditions exist that could create fogging on the

inside of the windshield. The A/C can be

deselected manually without disturbing the mode

control selection. Continuous use of the

Recirculation mode may make the inside air stuffy

and window fogging may occur. Extended use of

this mode is not recommended. Recirculation

mode may automatically adjust to optimize

customer experience for warming, cooling,

dehumidification, etc.
In cold weather, use of Recirculation mode may

lead to excessive window fogging. The

Recirculation feature may be unavailable if

conditions exist that could create fogging on the

inside of the windshield.

AUTO Button

Set your desired temperature and press

AUTO. AUTO will achieve and maintain

your desired temperature by

automatically adjusting the blower speed

and air distribution. Air Conditioning (A/C) may be

active during AUTO operation to improve

performance. AUTO mode is highly recommended

for efficiency. You can press and release this

button on the touchscreen, or push the button on

the faceplate, to turn AUTO on. The AUTO indicator

illuminates when AUTO is on. Toggling this function

will cause the system to switch between manual

mode and automatic modes

page 54.

GETTING TO KNOW YOUR VEHICLE

Front Defrost Button

Press and release the Front Defrost

button on the touchscreen, or push and

release the button on the faceplate, to

change the current airflow setting to

Defrost mode. The Front Defrost indicator

illuminates when Front Defrost is on. Air comes

from the windshield and side window demist

outlets. When the defrost button is selected, the

blower level may increase. Use Defrost mode with

maximum temperature settings for best

windshield and side window defrosting and

defogging. When toggling the front defrost mode

button, the climate system will return to the

previous setting.

Rear Defrost Button

Press and release the Rear Defrost

button on the touchscreen, or push and

release the button on the faceplate, to

turn on the rear window defroster and the

heated outside mirrors (if equipped). The Rear

Defrost indicator illuminates when the rear window

defroster is on. The rear window defroster

automatically turns off after 10 minutes.

Driver And Passenger Up And Down

Buttons

These buttons provide the driver and passenger

with independent temperature control.

Push the red button on the faceplate or

touchscreen or press and slide the

temperature bar towards the red arrow

button on the touchscreen for warmer

temperature settings.

Push the blue button on the faceplate or

touchscreen or press and slide the

temperature bar towards the blue arrow

on the touchscreen for cooler

temperature settings.

SYNC Button

Press the SYNC button on the

touchscreen to toggle the Sync feature

on/off. The SYNC indicator is illuminated

when SYNC is on. SYNC is used to

synchronize the passenger temperature setting

with the driver temperature setting. Changing the

passenger temperature setting while in SYNC will

automatically exit this feature.

NOTE:

The SYNC button is only available on the touch

screen.

Blower Control

Blower Control is used to regulate the

amount of air forced through the Climate

Control system. There are seven blower

speeds available. Adjusting the blower

will cause automatic mode to switch to manual

operation. The speeds can be selected using either

the blower control knob on the faceplate or the

buttons on the touchscreen.

CAUTION!

Failure to follow these cautions can cause

damage to the heating elements:



Use care when washing the inside of the rear

window. Do not use abrasive window cleaners

on the interior surface of the window. Use a

soft cloth and a mild washing solution, wiping

parallel to the heating elements. Labels can

be peeled off after soaking with warm water.



Do not use scrapers, sharp instruments, or

abrasive window cleaners on the interior

surface of the window.



Keep all objects a safe distance from the

window.

GETTING TO KNOW YOUR VEHICLE

Faceplate
The blower speed increases as you turn the blower

control knob clockwise from the lowest blower

setting. The blower speed decreases as you turn

the blower control knob counterclockwise.
Touchscreen
Use the small blower icon to reduce the blower

setting and the large blower icon to increase the

blower setting. Blower can also be selected by

pressing the blower bar area between the icons.

Mode Control

Select Mode by pressing one of the Mode

buttons on the touchscreen to change

the airflow distribution mode. The airflow

distribution mode can be adjusted so air

comes from the instrument panel outlets, floor

outlets, defrost outlets and demist outlets.

Panel Mode

Air comes from the outlets in the

instrument panel. Each of these outlets

can be individually adjusted to direct the

flow of air. The air vanes of the center

outlets and outboard outlets can be moved up and

down or side to side to regulate airflow direction.

There is a shut-off wheel located below the air

vanes to shut off or adjust the amount of airflow

from these outlets.

Bi-Level Mode

Air comes from the instrument panel

outlets and floor outlets. A slight amount

of air is directed through the defrost and

side window demister outlets.

NOTE:

Bi-Level mode is designed under comfort condi

tions to provide cooler air out of the panel outlets

and warmer air from the floor outlets.

Floor Mode

Air comes from the floor outlets. A slight

amount of air is directed through the

defrost and side window demister

outlets.

Mix Mode

Air is directed through the floor, defrost,

and side window demister outlets. This

setting works best in cold or snowy

conditions that require extra heat to the

windshield. This setting is good for maintaining

comfort while reducing moisture on the

windshield.

Climate Control OFF Button

Press and release this button to turn the

Climate Control ON/OFF.

UTOMATIC

EMPERATURE

ONTROL

(ATC)

Automatic Operation

1. Push the AUTO button on the faceplate, or the

AUTO button on the touchscreen on the

Automatic Temperature Control (ATC) Panel.

2. Next, adjust the temperature that you would

like the system to maintain by adjusting the

driver and passenger temperature control

buttons. Once the desired temperature is

displayed, the system will achieve and

automatically maintain that comfort level.

3. When the system is set up for your comfort

level, it is not necessary to change the

settings. You will experience the greatest

efficiency by simply allowing the system to

function automatically.

NOTE:



It is not necessary to move the temperature

settings for cold or hot vehicles. The system

automatically adjusts the temperature, mode,

and blower speed to provide comfort as quickly

as possible.



The temperature can be displayed in US or

Metric units within Uconnect Settings

page 123.

GETTING TO KNOW YOUR VEHICLE

To provide you with maximum comfort in the

Automatic mode during cold start-ups, the blower

fan will remain on low until the engine warms up.

The blower will increase in speed and transition

into Auto mode.

Manual Operation Override

This system offers a full complement of manual

override features. The AUTO symbol in the front

ATC display will be turned off when the system is

being used in the manual mode.

LIMATE

OICE

OMMANDS

Adjust vehicle temperatures hands-free and keep

everyone comfortable while you keep moving

ahead.
Push the VR button. After the beep, say one of the

following commands:



“Set driver temperature to 70 degrees”



“Set passenger temperature to 70 degrees”

TIP:

Voice Command for Climate may only be used to

adjust the interior temperature of your vehicle.

Voice Command will not work to adjust the heated

seats or steering wheel if equipped.

PERATING

IPS

Refer to the chart at the end of this section for

suggested control settings for various weather

conditions.

Summer Operation

The engine cooling system must be protected with

a high-quality antifreeze coolant to provide proper

corrosion protection and to protect against engine

overheating. OAT coolant (conforming to

MS.90032) is recommended.

Winter Operation

To ensure the best possible heater and defroster

performance, make sure the engine cooling

system is functioning properly and the proper

amount, type, and concentration of coolant is

used. Use of the Air Recirculation mode during

Winter months is not recommended, because it

may cause window fogging.

Vacation/Storage

For information on maintaining the Climate Control

system when the vehicle is being stored for an

extended period of time, see

page 307.

Window Fogging

Vehicle windows tend to fog on the inside in mild,

rainy, and/or humid weather. To clear the

windows, select Defrost or Mix mode and increase

the front blower speed. Do not use the

Recirculation mode without A/C for long periods,

as fogging may occur.

Outside Air Intake

Make sure the air intake, located directly in front of

the windshield, is free of obstructions, such as

leaves. Leaves collected in the air intake may

reduce airflow, and if they enter the air distribution

box, they could plug the water drains. In Winter

months, make sure the air intake is clear of ice,

slush, and snow.

Cabin Air Filter

The Climate Control system filters out dust and

pollen from the air. Contact an authorized dealer to

service your cabin air filter, and to have it replaced

when needed.

GETTING TO KNOW YOUR VEHICLE

Operating Tips Chart

INTERIOR STORAGE AND EQUIPMENT

TORAGE

Glove Compartment

The glove compartment is located on the

passenger side of the instrument panel.

Glove Compartment

To open the glove compartment, pull the release

handle.

Console Features

The center console has a storage compartment

located underneath the armrest. The compartment

contains a 12 Volt power outlet, and is also

equipped with a USB port featuring active

charging, which will continue charging your device

up to 60 minutes after the ignition is turned off.

The USB port also may be equipped with an

IPOD®/USB control

page 57, or Apple CarPlay®

and Android Auto™

page 167.

Center Console

WEATHER

CONTROL SETTINGS

Hot Weather And

Vehicle Interior Is

Very Hot

Set the mode control to

(Panel Mode), (MAX A/C)

on, and blower on high. Roll

down the windows for a

minute to flush out the hot

air. Adjust the controls as

needed to achieve comfort.

Warm Weather

Turn (A/C)

on and set the mode control

to (Panel Mode).

Cool Sunny

Operate in (Bi-Level

Mode).

Cool & Humid

Conditions

Set the mode control to

(Mix Mode) and turn

(A/C) on to keep windows

clear.

Cold Weather

Set the mode control to

(Floor Mode). If windshield

fogging starts to occur, move
the control to (Mix Mode).

WARNING!

Do not operate this vehicle with a console

compartment lid in the open position. Driving

with the console compartment lid open may

result in injury in a collision.

Dodge Challenger (2022 year). Manual in english - page 3