Content .. 492 493 494 495 ..

Acura RSX Honda Integra. Manual - part 494

−

０１

＊０１

０１

Ｓ６Ｍ６Ａ００Ｋ７９１０００８１１４４ＦＡＡＴ００

−

YES

DTC 14-4:

23-108

SRS

DTC Troubleshooting (cont’d)

SRS UNIT CONNECTOR B (18P)

8. Disconnect SRS unit connector B (18P) from the

SRS unit.

9. Check resistance between the No. 9 and No. 16

terminals of SRS unit connector B (18P). There
should be 0

1.0

Faulty front passenger’s side impact sensor

or SRS unit; replace the front passenger’s side
impact sensor (see page 23-142). If the problem is
still present, replace the SRS unit (see page 23-141).

Open in floor wire harness; replace the floor

wire harness.

1. Erase the DTC memory (see page 23-23).

2. Turn the ignition switch ON (II), and check that the

SRS indicator comes on for about 6 seconds and
then goes off.

Go to step 3.

Intermittent failure, system is OK at this time.

Go to Troubleshooting Intermittent Failures
(see page 23-24). If another DTC is indicated, go to
the DTC Troubleshooting Index.

3. Turn the ignition switch OFF. Disconnect the

battery negative cable, and wait for 3 minutes.

4. Disconnect the driver’s side airbag and front

passenger’s side airbag 2P connectors (A), and
disconnect both seat belt buckle tensioner 4P
connectors (B).

Faulty Power Supply to the Front

Passenger’s Side Impact Sensor

Wire side of female terminals

Is the r esistance as specif ied?

Does the SRS indicator stay on?

05/06/27 18:11:03 61S6M040_230_0108

０２

０３

＊０１

＊０２

−

YES

23-109

SRS UNIT CONNECTOR B (18P)

5. Disconnect the floor wire harness 2P connector (A)

from the front passenger’s side impact sensor (B).

6. Disconnect SRS unit connector B (18P) from the

SRS unit.

7. Check resistance between the No. 9 terminal of

SRS unit connector B (18P) and body ground. There
should be an open circuit or at least 1 M

Go to step 8.

Short to ground in the floor wire harness;

replace the floor wire harness.

8. Check resistance between the No. 9 and No. 16

terminals of SRS unit connector B (18P). There
should be an open circuit or at least 1 M

Faulty front passenger’s side impact sensor

or SRS unit; replace the front passenger’s side
impact sensor (see page 23-142). If the problem is
still present, replace the SRS unit (see page 23-141).

Short in the floor wire harness; replace the

floor wire harness.

Wire side of female terminals

Is the r esistance as specif ied?

05/06/27 18:11:03 61S6M040_230_0109

０１

０２

＊０１

Ｓ６Ｍ６Ａ００Ｋ７９１０００８１１５１ＦＡＡＴ００

−

DTC 15-1:

YES

’02-04 models

’05-06 models

YES

23-110

SRS

DTC Troubleshooting (cont’d)

OPDS UNIT 8P CONNECTOR D

WHT/RED

OPDS UNIT 8P CONNECTOR D

WHT

Faulty OPDS Unit or OPDS System

Not Initialized

1. Make sure nothing is on the front passenger’s seat.

2. Initialize the OPDS unit (see page 23-24).

3. Erase the DTC memory (see page 23-23).

4. Read the DTC.

Go to step 5.

Intermittent failure, system is OK at this time.

Go to Troubleshooting Intermittent Failures
(see page 23-24). If another DTC is indicated, go to
the DTC Troubleshooting Index.

5. Check the No. 9 (10 A) fuse in the under-dash fuse/

relay box.

Go to step 6.

Go to step 9.

6. Disconnect the OPDS unit 8P connector D from the

OPDS unit (A) (see page 23-143).

7. Turn the ignition switch ON (II).

8. Check for voltage between the No. 4 terminal of the

OPDS unit 8P connector D and body ground. There
should be battery voltage.

Go to step 16.

Open in floor wire harness or in the OPDS

unit harness; replace the faulty harness.

9. Replace the No. 9 (10 A) fuse in the under-dash

fuse/relay box.

10. Turn the ignition switch ON (II) for 30 seconds, then

turn it OFF.

Wire side of female terminals

Is DT C 15-1 indicated?

Is the f use OK ?

Is ther e batter y voltage?

05/06/27 18:11:04 61S6M040_230_0110

−

０３

０４

＊０２

−

YES

’02-04 models

’05-06 models

YES

23-111

BLK

OPDS UNIT 8P CONNECTOR D

WHT/BLU

OPDS UNIT 8P CONNECTOR D

11. Check the No. 9 (10 A) fuse in under-dash fuse/relay

box.

Intermittent failure, system is OK at this time.

Go to Troubleshooting Intermittent Failures
(see page 23-24). If another DTC is indicated, go to
the DTC Troubleshooting Index.

Go to step 12.

12. Replace the No. 9 (10 A) fuse in the under-dash

fuse/relay box.

13. Disconnect the OPDS unit 8P connector D from the

OPDS unit (A).

14. Turn the ignition switch ON (II) for 30 seconds, then

turn it off.

15. Check the No. 9 (10 A) fuse in the under-dash

fuse/relay box.

Short to ground in the OPDS unit; replace the

OPDS unit (see page 23-143).

Short to ground in the No. 9 (10 A) circuit.

16. Turn the ignition switch OFF.

17. Check resistance between the No. 8 terminal of the

OPDS unit 8P connector D and body ground. There
should be 0

1.0

Go to step 18.

Open in floor wire harness, seat subharness

(with BOSE sound system), OPDS unit harness, or
poor ground G501 (see page 22-59). If the G501 is
OK, replace the faulty harness.

(cont’d)

Wire side of female terminals

Is the f use OK ?

Is the r esistance as specif ied?

05/06/27 18:11:04 61S6M040_230_0111

Content .. 492 493 494 495 ..