Content .. 251 252 253 254 ..

FANUC Series 30i/300i/300is-MODEL A. Machining Center System. User's manual - page 253

1.ROUTINE MAINTENANCE

MAINTENANCE

B-63944EN/03

- 1980 -

CAUTION

1 The connector of the battery can be connected with

either of CX5X and CX5Y.

2 Attaching the battery from the cable outlet applies

tension to the cable. Therefore, attach the cable
from another place to prevent the cable from being
stretched. If this cable is connected on a stretch
condition, a bad conductivity may be occurred.

- Used batteries

Old batteries should be disposed as "INDUSTRIAL WASTES"
according to the regulations of the country or autonomy where your
machine has been installed.

APPENDIX

B-63944EN/03

APPENDIX

A.PARAMETERS

- 1983 -

PARAMETERS

This manual describes all parameters indicated in this manual.
For those parameters that are not indicated in this manual and other
parameters, refer to the parameter manual.

NOTE

A parameter that is valid with only one of the path
control types for the lathe system (T series) and
machining center system (M series) is indicated in
the upper or lower row as described below. A blank
represents an unusable parameter.

[Example 1]

The parameter HTG is common to the T series and
M series, and RTV and ROC are parameters used
with the T series only.

1403

RTV

ROC

HTG

T series

M series

[Example 2]

The following parameter is used with the M series
only:

1411

Cutting feedrate

T series

M series

A.PARAMETERS

APPENDIX

B-63944EN/03

- 1984 -

A.1

DESCRIPTION OF PARAMETERS

#7 #6 #5 #4 #3 #2 #1 #0

0000

ISO

TVC

[Input type] Setting input

[Data type] Bit path

# 0

TVC

check

0: Not

performed

1: Performed

# 1

ISO

Code used for data output

0: EIA

code

1: ISO

code

NOTE

ASCII code is used at all times for output to the
memory card.

#7 #6 #5 #4 #3 #2 #1 #0

0001

FCV

[Input type] Setting input

[Data type] Bit path

# 1

FCV

Program

format

0: Series 16 standard format
1: Series 15 format

NOTE

1 Programs created in the Series 15 program format

can be used for operation on the following
functions:

1  Subprogram call M98
2  Thread cutting with equal leads G32 (T series)
3  Canned cycle G90, G92, G94 (T series)
4  Multiple repetitive canned cycle G71 to G76 (T

series)

5 Drilling canned cycle

G83.1, G80 to G89 (T series)
G73, G74, G76, G80 to G89(M series)

2 When the program format used in the Series 15 is

used for this CNC, some limits may add. Refer to
the User’s Manual.

B-63944EN/03

APPENDIX

A.PARAMETERS

- 1985 -

#7 #6 #5 #4 #3 #2 #1 #0

0010

PRM

[Input type] Setting input

[Data type] Bit path

# 1

PRM

When parameters are output, the parameters whose values are 0 are:

0: Output.
1: Not

output.

#7 #6 #5 #4 #3 #2 #1 #0

0012

MIRx

[Input type] Setting input

[Data type] Bit axis

# 0

MIRx

Mirror image for each axis

0: Mirror image is off. (Normal)
1: Mirror image is on. (Mirror)

0020

I/O CHANNEL : Input/output device selection, or interface number for a

foreground input device

[Input type] Setting input

[Data

type]

Byte

[Valid data range] 0 to 5

The CNC has the following interfaces for transferring data to and from
an external input/output device and the host computer:

Input/output device interface (RS-232-C serial ports 1 and 2)

Memory card interface

Data server interface

Embedded Ethernet interface

By setting bit 0 (IO4) of parameter No. 0110, data input/output can be
controlled separately. When IO4 is not set, data input/output is
performed using the channel set in parameter No. 0020. When IO4 is
set, a channel can be assigned to each of foreground input, foreground
output, background input, and background output.
In these parameters, specify the interface connected to each
input/output device to and from which data is to be transferred. See
the table below for these settings.

Correspondence between settings and input/output devices

Setting Description

0,1

RS-232-C serial port 1

RS-232-C serial port 2

Memory card interface

Data server interface

Embedded Ethernet interface

A.PARAMETERS

APPENDIX

B-63944EN/03

- 1986 -

#7 #6 #5 #4 #3 #2 #1 #0

0100

NCR

CTV

[Input type] Setting input

[Data

type]

Bit

# 1

CTV

Character counting for TV check in the comment section of a

program.
0: Performed
1: Not

performed

# 3

NCR

Output of the end of block (EOB) in ISO code

0: LF, CR, CR are output.
1: Only LF is output.

#7 #6 #5 #4 #3 #2 #1 #0

0138

MNC

[Input type] Parameter input

[Data

type]

Bit

# 7

MNC

DNC operation from the memory card and external device

subprogram call from the memory card are:
0: Not

performed.

1: Performed.

0983

Path control type of each path

NOTE

When this parameter is set, the power must be
turned off before operation is continued.

[Input type] Parameter input

[Data type] Byte path

[Valid data range] 0 to 1

Set the path control type of each path.
The following two path control types are available:
T series (lathe system)

: 0

M series (machining system) : 1

B-63944EN/03

APPENDIX

A.PARAMETERS

- 1987 -

#7 #6 #5 #4 #3 #2 #1 #0

0984

LCP

[Input type] Parameter input

[Data type] Bit path

NOTE

When this parameter is set, the power must be
turned off before operation is continued.

# 0

LCP

Set whether the path is a loader control path.

0: The path is not a loader control path.
1: The path is a loader control path.

#7 #6 #5 #4 #3 #2 #1 #0

1001

INM

[Input type] Parameter input

[Data type] Bit path

NOTE

When this parameter is set, the power must be
turned off before operation is continued.

# 0

INM

Least command increment on the linear axis

0: In mm (metric system machine)
1: In inches (inch system machine)

#7 #6 #5 #4 #3 #2 #1 #0

1002

IDG

XIK

AZR

JAX

[Input type] Parameter input

[Data type] Bit path

# 0

JAX

Number of axes controlled simultaneously in jog feed, manual rapid

traverse and manual reference position return
0: 1

axis

1: 3

axes

Content .. 251 252 253 254 ..