Iran Khodro Samand SE. Service Manual - part 4

54

2

ALARM

* If equipped

1- Alarm* 

55

2

ALARM

Audio – video alarm specification

1. Audio and video capability

2. LCD display

3. Keypad

4. Loud speaker

5. Temperature Sensor

Capability

1. Warning messages are displayed on 

the LCD screen.

2. Vocal warning to notify different messages.

3. Theft deterrent with the following 

specifications:

a) 4 digit password possibility

b) shock sensor with ability of sensibility 

adjustment by software

c) Dual position LED memory.

4. Control timer for RLT roof light

5. Measurement of vehicle interior temperature 

and their display on LCD

6. Equipped with inertia switch for opening 

the doors in case of accident

7. Possibility of changing the back light by 

software

Audio-Visual Alarm Specification

1. During the course of driving, warning 

messages are displayed on the LCD and 

an audio message is broadcasted through 

speakers according to the type of error.

2. This system has tree principal menus 

and eight sub-menus in the settings menu, 

each provided for a specific purpose.

3. Theft deterrent with 4 digit code and siren.

Buttons’ Function

  Button functions in all menus and 

confirms  selected  menu  and  and  input 

data.

 Button is used to stop the sound of 

audio warning and to exit all menus.

By repressing of the 

  button, the 

audio warnings is activated.

 

  Buttons are used for up and 

down, left and right moving.

 Button is used to turn the instrument 

panel on and off.

 Button is used to cut off the warning 

alarm when speed exceeds 120 KM an 

hour and to cut the beep sound of keypad. 

By pressing once again this button the 

warning alarm option is turned on.

By pressing the 

 button on the  main 

menu you can adjust the LCD light from 

0 to 100%

The sign   appears when air condition 

works.     

56

2

ALARM

Warning message

Warning controls detectable problems 

when the car starts running.

Two seconds after a problem occurs, the 

driver is notified in two ways:

1. One can hear the audio warning 

 

through the loud speaker

2. Video warning displays on the screen.

When the car is running, if any of the 

following problems occurs corresponding

warnings are displayed and diffused:

1. The hand brake or brake liquid 

should be controlled

2. Oil pressure is low

3. Replace the brake pad.

4. Water temperature is high

5. Doors are open

6.Turn off the lights

7. Change the engine oil

8.Change the oil filter

9.Change the air filter

Press 

 the button to cut the warning 

sound. The sign ( ) appears on the 

screen. The warning message appears 

but no sound is heard.

 

 Button does not cut the message

related to the lights being left on and the

message will continue in all situations.

Theft-Deterrent

When the remote keyless is used to 

lock the car, all doors, hood, the trunk lid 

and  fuel  filler  cap  are  locked  and  theft-

deterrent is activated. The message “the 

anti-theft is active” appears on the screen 

and the panel light or the corresponding 

signal ( ) blinks on the instrument panel.

If you lock the doors with the key, theft-

deterrent system will not be activated. 

In addition to the usual theft deterrent 

means, the intelligent theft deterrent of 

Samand is equipped with extra capabilities 

as follows:

a) 4 digit code

b) Shock sensor with ability to be set up 

by software

c) memory LED in two positions

57

2

ALARM

Theft-Deterrent is active:

If the car is in “unlock” mode, the “lock” 

button is pressed ,and doors are closed :

The doors are locked and shock sensor 

is activated after 7 seconds. Siren and 

flasher are triggered once. 

If there is any impact against the vehicle 

at this time, the shock sensor is triggered 

depending  on  the  predefined  sensibility. 

Therefore siren and flashers are activated 

continuously for 30 seconds and the map 

reading light stays on for 30 seconds 

and the danger sign is displayed(2). If 

shock sensor remains active for about 30 

seconds,  siren  and  flasher  are  triggered 

for 30 seconds too, map reading light 

stays on and this trend continues, if the 

shock sensor is not triggered, the returns 

to theft deterrent position and memory 

LED remains on, showing a danger till the 

vehicle starts. 

If in theft deterrent position one of the doors 

becomes open, like the previous situation, 

siren  and  flasher  are  triggered,  and  the 

checks the door after 30 seconds. 

If the door is closed, the returns to theft 

deterrent position, if not, door opening 

alarm in theft deterrent position is activated, 

meaning  that  the  siren  and  flashers  are 

continuouslyactivated during 30 s. When 

the vehicle is in theft deterrent position, 

if (On) button on the remote control is 

pressed,  siren  and  flasher  turn  on  once 

for confirming the activated theft deterrent 

position (Panic) and map reading light turns 

on and turns off with delay.

Remark:

1- Activating siren once means : siren 

works for 20 ms.

2- One time activating of flasher means, 

flasher works for 500ms

58

2

ALARM

a) If 4 digit code is activated on the intelligent 

(menu 3), figure 3 appears, after unlocking 

and opening the door, if at the end of the 

specified time in the code duration setting 

page, no code is entered or is entered 

by mistake, intelligent shifts to alarm and 

siren  and  flashers  work  for  30  s  (figure 

5). It should be noted that the code can 

be entered three times in a row and if the 

code is entered by mistake for the third time 

(figure 4) shifts to alarm position.

b) And if 4 digit code is not activated and door 

is not opened during 10 seconds, the vehicle 

shifts to lock and theft deterrent position, 

unless one of the buttons on the key pad is 

pressed or the vehicle is started.

Alarm in normal position 

When the is not in theft deterrent position, 

the following capabilities have been 

included to the intelligent:

a) When the vehicle is off and driver 

leaves the vehicle and door is closed, 

after 5 seconds, the siren triggers 5 times 

on 200 ms intervals for reminding to lock 

the vehicle. 

b) Doors are opened with button 1 and 

closed with button 3 on the intelligent 

keyboard.

c) When the speed of vehicle exceeds 20 

Km/h, doors will be locked automatically 

and they will open when the vehicle 

isturning off.

Four digit code:

when the vehicle is in theft deterrent mode 

and unlock (Off) button is pressed:

59

2

ALARM

Map reading light timer

Map reading light control comes on by 

activating intelligent and operates in the 

following situations:

1-While the vehicle is off and the vehicle 

door or trunk is opened, this light turns on 

and while the door is closed, the light stays 

on for 12s and then turns off progressively.

2- When the vehicle is in theft deterrent 

position, by pressing the 

unlock button, 

light stays on; otherwise, it will be activated 

by 

auto-lock and the map reading light 

will turn off automatically.

3- In the case of danger and alarm, the 

map reading light remains on till the end of 

the theft-deterrent alarm position.

4- Should any of the vehicle’s doors (such 

as trunk lid and engine hood) are open, 

when driving, roof light informs driver by 

blinking.

How the background light turns 

on and off?

Effective factors influencing on background 

light turning on and off are as follow:

1- Alarm Position

2- Anti-Theft Position

3- L key

4- Front Light On/Off Position

5- On/Off Position

6- Keyboard keys (except L)

7- Messages display

Escorting of driver in darkness

When you’re leaving the vehicle in dark 

places ,you can keep the space alight for 

30 seconds by turning on the small lights 

and low light. For this purpose:

- Keep the switch in Stop position(or take 

out the switch)

- Turn off the lights.

- Pull the indicator once towards yourself. 

- Get out of the vehicle and lock it.

- small lights and low light will get on 

automatically after 30 seconds and then will 

get off again. 

Automatic lock:

If the theft deterrent is activated, if the 

“open” key is pressed on the remote 

control, but none of the side doors, hood 

door or trunk lid are opened within 12 

seconds, the theft deterrent will lock 

all side doors, hood door and trunk lid 

automatically And the antitheft system will 

be activated. After turning the engine on 

and speeding up to 10 km/hour, doors will 

be locked and unlocked after turning off 

the switch.

Note:

 In the event of failure of any one 

of the keys  (side doors, trunk or hood) or 

shock sensor (if installed on the vehicle) 

corresponding entry in the active state 

of alarm is not checked and the situation 

when activating the alarm Gyraz key to 

activate the remote control with 4 times 

flasher and siren* (the distance between 

two consecutive) that is distinct from the 

normal warning is given. In this case 

it is necessary as soon as possible to 

overcome the problem by referring to the 

agency’s action.

Car finder:

While the anti theft system is activated, 

alarming* system gets activated once and 

the flasher starts blinking for 15 seconds 

by pressing the close key on remote 

control.

Note:

1- Activation of alarming system ,means it 

gets activated just for 0.020 second.

2-  Activation  of  flasher  ,means  it  gets 

activated just for 400 milliseconds.

3- You can disconnect alarming system 

by special switch delivered to you among 

other keys of the vehicle.

* If equipped

60

2

ALARM

Warning

None of battery cables should be 

disconnected more than 15 minutes, 

otherwise temporary ECU memory 

will be erased.

Alarm resetting

For resetting the the battery and siren 

connector should de disconnected and 

reconnected. You can disconnect the 

siren by the special switch that has been 

delivered to you Disconnect the siren 

connectors and unscrew battery terminal 

negative cable and remove the battery 

cap.  Then  once  again,  first  place  the 

battery cap and tighten its screw, then set 

the siren connector and set the switch to 

on position. Now, the is reset and time 

adjustment should be renewed.

61

2

ALARM

Alarm general information

If the car speed exceeds 120 KM per 

hour, warning alarm is heard and beeps 

increases in number when the car speeds 

up. The alarm can be turned on / off by 

pressing 

 button.

The keypad lamp and the display screen light 

up when main headlights are turned on.

The default display illumination intensity is 

50%. Display on or display off options and 

the illumination intensity are memorized 

as default.

The clock is displayed in the main menu 

screen as default setting. Refer to menu 4 

explanations for clock adjustments.

On the main menu press button 

on the keypad to unlock doors and 

button to lock the doors. 

This option can be used to open the doors 

in speeds over 20 KM /h.

Main Menu

menu details are as follows:

1- Distance Display

2- Oil Filter

3- Settings

3.1 Temperature Adjustment

3.2 Shock Sensor

3.3 Code Settings

3.4 Clock Adjustment

3.5 Date Adjustment

3.6 Contrast

3.7 Language Changing

3.8 Default Settings

62

2

ALARM

The main menu display is according to 

(7), we can choose one of the 3 options 

by pressing the 

 or 

  keys and 

entering the corresponding menu by 

pressing 

 .On this page by pressing 

the 

  key the main menu appears. 

To enter adjustment menu, the 

 key 

should be pressed for 1 second.

Distance display screen

On this screen the distance is shown in 

kilometers (8). Any time the 

 button 

is pressed, the distance will be reset to 0 

and it will restart from 0.

Oil filter screen

This page is divided into the kilometers 

adjustment page and usage.

 

 

Kilometers adjustment

When  adjusting  oil  level,  oil  filter  or  air 

filter it is possible to enter the maximum 

amount of proper usage for oil or air filter 

in kilometers (9).

63

2

ALARM

To change the kilometer setting, 

  or 

 should be pressed and then press 

 

to confirm. By pressing 

, the message 

“should the adjustments be confirmed?” is 

displayed (10), and if 

 key is pressed, 

the changes will be confirmed and if 

 

key is pressed, the changes will not be 

considered.

Usage:

In this menu the usage of oil, filter, air filter 

is shown in kilometers. By pressing 

 

key, this page is closed.

Driver information display menus:

There are 8 sub-menus in the warning. 

By pressing 

 key on adjustments, the 

sub-menu is activated (11).

By pressing 

 or 

 buttons choose 

the desired menu, and then press the 

 key (12). After termination press the 

 key to exit menu.

64

2

ALARM

Option Menu1:Temperature setting

“Internal Temperature” indicates the 

temperature level inside the car.

“Temperature Setting” indicates the level 

selected by the user.

This menu also enables the user to set the 

temperature for AC.

  Pressing this button will decrease 

the temperature setting . 

 Pressing this button will increase the 

temperature setting.

Select “Temperature Setting” in Option 

Menu1.

 Pressing this button allows selection 

of Automatic or Manual option and at the 

end press 

 button.

By pressing the 

 key, you can choose 

the automatic or manual positions.

Default position is manual position. AC will 

remain on and there will be no control over 

the temperature. In “Automatic” mode, to 

“decrease” to the internal temperature set 

by the user, the AC will turn on and off till 

it maintains the selected internal cabin 

temperature. This (AC) can not adjust the 

temperature while the heating is working. 

The activation or deactivation of the AC is 

shown by on or off (13).

Option Menu 2: Theft-Deterrent 

(Shock Sensor)

 Press this button to navigate to option 

menu 2. In this menu you can choose the 

sensitivity of the shock sensor (14).

65

2

ALARM

Shock sensor display

By pressing 

  and 

  buttons, the 

shock sensor sensitivity can be altered 

from 0 to 100 (15&16). When the sensitivity 

is 100, the theft-deterrent will be activated 

even by the smallest shock .

On the opposite, when the sensitivity is 

near to 0, the alarm will be activated only 

after a heavy shock and if the “shock 

sensors” are placed on 0, the alarm (sire) 

will be totally deactivated.

 Press this button to exit the menu.

Option menu 3: Security code setting

 Press this button to navigate to Option 

Menu 3. This menu allows the user to (17): 

- Change the 4 digit code number. 

- Reset the time allowed for keying in the 4 

digit code number. - Activate or deactivate 

the 4 digit code number.

66

2

ALARM

To make any changes in this menu, you must 

enter the correct 4 digit code number (18). 

If the correct code is not entered, this 

message will be displayed:”Security Code is 

incorrect” and the menu will be closed down. 

After the correct code has been entered, a 

sub-menu will be appeared. (19)

By pressing the 

 and 

 buttons you 

can move between different positions.

If the code is activated (20), you have to 

enter the four digit code number before 

starting.

If the code is not activated you do not 

need to enter the four digit code number 

before starting.

 

The default code is 1111 and you can 

change it as you wish.

In default mode, the four digit code is 

deactivated. If you forget your four digit 

code and a problem occurs for the , you 

can reset the as mentioned; in this case 

the default codes will be1111.

67

2

ALARM

For- Digit code number changing

  Pressing this button selects the 

option to “Change Security Code”(21).

You will then be able to enter a new 4 digit 

code number(22).

After entering the four digits, you will be 

requested to enter the new code number once 

more. If two digits of this entry are the same, 

this code number will change to become your 

new 4 digit code number. If digits do not match, 

the following message will be displayed:”The 

security number is incorrect” and no new 

security code will be set.

68

2

ALARM

Password Time Selection

By pressing 

  button select the 

“adjusting code duration” mode.

In this way you can change the duration 

for entering the code. 

By pressing 

  key, 4 options will be 

displayed on the screen for duration (24).

By pressing 

  and 

  buttons you 

can adjust the desired time.

By pressing 

 button the selection sign 

will move to the left and by pressing 

 

button it will move to the right. By pressing  

  button this display screen will be 

closed.

The duration for entering the code will 

start at the opening of doors or pressure 

on one of the keys.

By pressing 

 button on “four digit code 

number” mode you can activate or deactivate 

“four digit code number” mode (25).

In activation mode the start will not operate 

until the correct code number is entered 

and when exiting the theft deterrent mode, 

the will ask for the four digit code number.

By pressing 

  button exit the menu. 

When the code number is activated, it is not 

possible to open the hood without entering 

the code and the alarm will go on. If the code 

is deactivated, when exiting the anti-theft 

mode, there is no need to enter the code(26).

Option menu 4: Clock setting

By pressing 

 button, enter menu 4(27).

69

2

ALARM

In this mode a dark line will appear under 

the time digit (28).

By pressing 

 and 

 buttons, adjust 

the clock digit.

By pressing 

 button, you can move on 

the minute and second digits and adjust 

them accordingly.

By pressing 

 button, you can activate 

or deactivate clock display on the main 

menu (29). 

Exit menu by pressing 

 button.

Option menu 5: Date adjustment

By pressing 

 button enter menu 5(30).

In this menu you can choose the day, 

year, month and weekdays options.

By pressing the 

 button the dash sign 

will move between year, month and day (31).

By pressing the 

  and 

  buttons, 

adjust the date.

If the date is adjusted, weekdays will be 

adjusted automatically.

The range of adjustable date is 50 years.

By pressing the 

 button, exit menu.

Press 

 button to exit the menu.