Snowmobile Polaris 600 IQ LXT (2015 year). Manual - part 10

43

FEATURES

Instrumentation

MFD Digital Display Programs

Engine Program

The Engine Program automatically displays the engine coolant 
temperature, engine hours, electrical system voltage level and fuel level 
(if equipped). On machines equipped with altimeter sensor and ambient 
air temperature sensors, altitude and ambient air temperature will 
display as additional screens in the engine program. Press the SET 
button to display the ambient air temperature and altitude screens. Use 
the following procedures to make changes to these screens.

Hour Meter

The hour meter records the total hours of 
engine operation since manufacture. This 
meter cannot be reset.

Engine Temperature

A thermometer measures water temperature, 
giving an indication of engine temperature.

Air Temperature (if equipped)

The MFD displays actual air temperature in 
either standard or metric units.

1. Enter the Engine Program.

2. Press and hold the MODE switch for ten 

seconds to switch between standard and 
metric units of measurement.

44

FEATURES

Instrumentation

MFD Digital Display Programs

Engine Program
Altitude (if equipped)

The rider can calibrate the altimeter for current 
atmospheric conditions. Altimeter accuracy 
will be +/-300 ft. (91 m) after adjustment.

1. Enter the Engine Program.

Tip: Press and hold the MODE switch for ten sec-

onds to switch between standard and metric 
units of measurement. When "ALt" displays, the 
program is in the metric mode.

2. Press and release the SET button until the altimeter screen is active.

3. Press and hold the SET button for five seconds. When the digits 

begin to flash, release the button. 

4. Press and release the SET button once to advance 50 feet (15 m).

Tip: Press and hold the SET button to advance quickly by 100-foot (30 m) 

increments.

5. Adjust the altitude display to within 50 ft. (15 m) of current altitude.

Tip: The gauge reads barometric pressure and allows the rider to compensate 

for daily fluctuations in air pressure. The gauge can adjust the displayed 
altitude to +/- 1300 ft. (396 m) from the preset value. It will adjust up to 
+1300 ft. (396 m) above the calibrated altitude. Once the +1300 ft. (396 m) 
offset has been reached, the next adjustment is -1300 ft. (396 m) from the 
calibrated altitude, and 50 ft. (15 m) will be added to the altitude each time 
the SET button is pressed.

6. Press and release the MODE button to set the reading at the adjusted 

value. If the MODE button is not pressed within ten seconds, the 
gauge will automatically save the new entry.

45

FEATURES

Instrumentation

MFD Digital Display Programs

History Program

The History Program automatically displays electrical system voltage 
level and fuel level (if equipped).

While in the History mode, press the SET button to view maximum 
vehicle speed, maximum engine rpm or the current service interval 
setting. The gauge automatically logs the maximum speed and engine 
rpm even if the History Program is not currently displayed. 

The History Program will display the history of the Maximum Speed, 
Maximum RPM and Service Interval settings.

Maximum Speed/Maximum RPM

1. Enter the History Program.

2. Press and release the SET button until 

one of the two screens is active.

Tip: The MPH and RPM values are both reset at 

the same time. Reset the values before each 
run to obtain accurate readings. 

3. Press and hold the SET button for three 

seconds to reset the recorded maximum 
values for both MPH and RPM.

Tip: Due to electrical noise, the MFD may 

occasionally display MAX MPH/RPM values 
that are not representative of actual values.

46

FEATURES

Instrumentation

MFD Digital Display Programs

History Program
Service Interval Reminder

The gauge logs the number of engine 
hours accumulated between service 
reminders. When the logged hours 
reaches the designated service interval 
(set by the user), the gauge provides a 
reminder that service is due. "SErVCE" 
will flash in the odometer area and 
"ENG" will flash in the icon area for five 
seconds each time the engine is started 
(until the service reminder is reset.) Use 
the following procedures to reset the 
reminder.

To reset the reminder at the existing interval:

1. Enter the History Program.

2. Press and release the SET button until the service interval screen is 

active.

3. Press and hold the SET button for ten seconds, continuing to hold 

even after the display begins to flash.

4. When the display stops flashing, release the button. The service 

interval has been reset.