Snowmobile Polaris 600 IQ LXT (2015 year). Manual - part 8

 

  Index      Snowmobiles / ATV     Snowmobile Polaris 600 IQ LXT - service manual 2015 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  6  7  8  9   ..

 

 

Snowmobile Polaris 600 IQ LXT (2015 year). Manual - part 8

 

 

35

FEATURES

Detonation Elimination Technology (DET)

The DET system prevents damage to the engine from detonation by 
automatically reducing the engine timing and adding fuel whenever the 
sensors detect detonation.

You may notice decreased engine RPM and performance when DET is 
activated, but in most cases DET activation is temporary, and the timing 
will return to normal automatically. In extreme conditions the DET 
system retards timing and holds it in a retarded state. If this occurs, 
replace the fuel with recommended fuel or see your POLARIS dealer 
for service.

Sensor Fail-Safe

The DET includes a sensor fail-safe system to prevent the engine from 
damage if the sensor fails, becomes disconnected or is unable to detect 
detonation. The rider will experience a loss of power. The sensor must 
be reconnected or repaired to regain full power. See your POLARIS 
dealer for service if this occurs.

Tip: The check engine light will flash six times if the sensor fails or becomes 

disconnected.

Cause of DET Activation

Solution

Poor quality fuel

Replace with higher quality fuel

Improper engine modifications

Do not modify the engine

36

FEATURES

Instrumentation

MFD Component Identification

Digital Display Identification

Item

1

Analog (if equipped)

2

Digital Gauge

3

Check Engine Indicator

4

Low Oil Indicator

5

High Temp Indicator

6

Brake Indicator

7

Reverse Indicator

8

High Beam Indicator

Item

1 RPM or Speed

Altitude (if equipped)
Service Interval

2 Electrical System Voltage 

Level

3 MAX - Maximum MPH/

KPH or RPM

MPH - Miles per hour
KPH - Kilometers per hour
RPM - Engine crankshaft

revolutions per
minute

4 Air Temp (if equipped)

Engine Temp
Degrees Celsius
Degrees Fahrenheit

5 Miles

Kilometers

6 Hours

Trip 1/Trip 2/Trip F 
Service Label
Altitude Label

7 Fuel Level (if equipped)

1

2

3

5

6

7

8

4

1

2

3

4

5

6

7

37

FEATURES

Instrumentation

MFD Settings

The MFD control switch allows you 
to set the MFD display to your 
preferences. The rocker switch has a 
MODE button (top) and a SET 
button (bottom). Specific 
instructions are outlined on the 
following pages.

Standard vs. Metric

The MFD will display either stan-
dard or metric units of measurement. 
While viewing a screen that displays 
measurements (MPH, km/h or temperatures), press and hold the MODE 
switch until the unit of measurement changes (about 10 seconds). 

MFD Control Switch

SET

MODE

38

FEATURES

Instrumentation

MFD Settings

Speedometer/Tachometer

The speedometer and tachometer can be viewed in either the analog or 
the digital display. If the analog display is set to show speedometer 
readings, the digital screen will automatically display the tachometer 
(option 1). If the analog is set to show the tachometer, the digital screen 
will show the speedometer (option 2).

To change viewing preferences, press and hold the MODE button for 
three seconds. When the button is released, the new setting becomes 
active and screen colors change. See table below.

Option

Analog

Display

Digital

Display

Analog

Screen

Digital

Screen

1

Speed

RPM

Blue “MPH”

Blue

Backlight

2

RPM

Speed

Red 

“X100RPM”

Red

Backlight

 

 

 

 

 

 

 

Content   ..  6  7  8  9   ..