Aprilia RS 250. Manual - part 29

 

  Index      Manuals     Aprilia RS 250. Repair Manual

 

Search            

 

 

 

 

 

 

 

 

Content   ..  27  28  29  30   ..

 

 

Aprilia RS 250. Manual - part 29

 

 

9

- 7

---    -     -  ---

RS 250 

  -    --  - 

Estos números son necesarios para matricular el vehícu-
lo.

La alteración de los números de identificación
puede provocar graves sanciones penales y

administrativas; en particular, la alteración del núme-
ro del bastidor produce la anulación inmediata de la
garantía.

NUMERO DE BASTIDOR

El número del bastidor está impreso en el manguito de la
dirección, lado derecho.

NUMERO DEL MOTOR

El número del motor está impreso en el lado trasero, cer-
ca del piñón.

- -  -    - 

Los dos cilindros del motor se identifican con “L” para el
cilindro izquierdo y “R” para el derecho.

--      --

 -   -

COMBUSTIBLE

El combustible para la propulsión de los mo-
tores de explosión, es muy inflamable y puede
volverse explosivo en determinadas condicio-

nes. Es oportuno reponer gasolina y realizar las ope-
raciones de mantenimiento en una zona ventilada y
con el motor apagado. No fume durante la provisión
de gasolina y cerca de los vapores del combustible;
evite el contacto con llamas, chispas y cualquier otra
fuente que pueda causar el encendido o la explosión. 
Además, evite que el combustible salga de la boca de
llenado, ya que éste podría incendiarse si toca las su-
perficies candentes del motor. 
En caso que se vierta accidentalmente combustible,
antes de arrancar el vehículo, controle que la zona
esté completamente seca. 
El combustible se dilata con el calor y bajo la acción
de los rayos solares. Por lo tanto, nunca llene el de-
pósito hasta el tope. Cierre cuidadosamente la tapa al
finalizar las operaciones de reposición. 
Evite el contacto del combustible con la piel, la inha-
lación de los vapores, la ingestión y el trasiego de un
recipiente a otro por medio de un tubo.

NO VIERTA EL COMBUSTIBLE EN EL MEDIO 
AMBIENTE.

MANTÉNGASE LEJOS DEL ALCANCE DE LOS NIÑOS.

Utilice exclusivamente gasolina super sin plomo según
DIN 51 607, mínimo de octano 95 (N.O.R.M.) y 85
(N.O.M.M.).





-      -

These numbers are necessary  in order to register the ve-
hicle. 

Do not alter the identification numbers if you
do not want to incur severe penal and admin-

istrative sanctions. In particular, the alteration of the
frame number results in the immediate invalidity of
the guarantee.

FRAME NUMBER

The frame number is stamped on the right side of the
steering column.

ENGINE NUMBER

The engine number is stamped on the rear part of the
engine, near the pinion.



The two cylinders of this engine are identified as “L” left
cylinder and “R” right cylinder.

 --       

 -  -   -

FUEL

The fuel used for internal combustion engines
is extremely inflammable and  in certain con-
ditions can become explosive. 

It is advisable to perform the operations of refuelling
and maintenance in a well-ventilated area with the en-
gine switched off. Do not smoke while refuelling or
when near fuel vapours and, in any case,  avoid con-
tact with naked flames, sparks and any other source
of heat  that might cause the fuel to catch fire or to
explode. Avoid escape of fuel from the fuel filler as it
could ignite on contact with the red-hot surfaces of
the engine. 
In case fuel has accidentally been spilt, make sure
that the area is completely dry before starting the ve-
hicle.
Never fill the tank to the brim as fuel expands under
the heat of the sun and reacts to the effects of sun ra-
diation .
Close the cap securely after refuelling. 
Avoid contact of the fuel with the skin and inhalation
of the fumes; do not swallow fuel or pour it from one
container into another by means of a tube.

DO NOT DISPOSE OF FUEL IN THE ENVIRONMENT.

KEEP FUEL AWAY FROM CHILDREN.

Use only premium grade unleaded petrol according to the
DIN 51 607, min. O.N. 95 (N.O.R.M.) and 85 (N.O.M.M.).





-------------------------------------------------------------------------------------------------------------------------------------------------------------

---    -

9

- 10

RS 250 

ACEITE CAMBIO

El aceite puede dañar gravemente a la piel si
es manejado durante mucho tiempo y diaria-
mente. Se aconseja lávarse las manos con

mucho cuidado tras haberlo manejado.

No esparza el aceite en el ambiente. 
Se aconseja llevarlo en un recipiente sellado a la es-
tación de servicio donde lo compra normalmente o a
un centro de recogida de aceites. 

En caso de intervenciones de mantenimiento, se
aconseja el uso de guantes de látex.

Controle cada 4000 km (2500 mi) el nivel del aceite cam-
bio, véase pág. 2-22 (ACEITE DEL CAMBIO).

Hay que sustituir el aceite del motor tras los primeros
1000 kilómetros (625 mi) y sucesivamente cada 12000
km (7500 mi), véase pág. 2-22 (ACEITE DEL CAMBIO).

Aceite cambio (aconsejado):



 F.C. SAE 75W - 90.

Alternativamente al aceite aconsejado, pueden utilizarse
aceites de marca con prestaciones conformes o superio-
res a las especificaciones A.P.I. GL-4.

ACEITE MEZCLADOR

Utilizar aceite sintético con las características ISO-L-
ETC++A.P.I. TC++ especial para gasolina sin plomo.

Aceite mezclador (aconsejado):



 MAX 2T COMPETITION.

Este aceite ha sido estudiado para obtener las máximas
prestaciones del motor con menos residuos en la cámara
de explosión, menos autoencendidos, máxima duración
de las bujías y mejor lubricación.

ACEITE PARA HORQUILLA

El aceite para horquilla puede causar graves
daños a la piel si es manipulado por mucho
tiempo y diariamente. Se aconseja lavarse las

manos tras haberlo manipulado.
No esparza el aceite en el medio ambiente. 
Entréguelo o hágalo retirar por la empresa de recupe-
ración de aceites usados más cercana o por el pro-
veedor.

En caso de intervenciones de mantenimiento, se
aconseja el uso de guantes de látex.

Modificando la regulación de los dispositivos de amor-
tiguación y/o la viscosidad del aceite contenido en és-
tos, se puede variar parcialmente la respuesta de la
suspensión.

Viscosidad aceite estándar: SAE 20W.



 F.A. está disponible en dos gradaciones de vis-

cosidad que se pueden elegir según el tipo de ajuste
que se quiere dar al vehículo (SAE 5W blando, 20W
rígido).

Es posible utilizar los dos productos en porcentajes
variables hasta alcanzar el tipo de respuesta
deseado.



 F.A. se caracteriza por variar poco su viscosidad

según la temperatura, y por lo tanto mantiene con-
stante la respuesta de amortiguación.

Aceite para horquilla (aconsejado): aceite para horqui-
llas 



 F.A. 5W o bien 



 F.A. 20W.

Si se desea utilizar un aceite con comportamiento inter-
medio, entre aquéllos ofrecidos por 



 F.A. 5W y por IP

F.A. 20W, pueden mezclarse los productos como indica-
do a continuación:

SAE 10W



 F.A. 5W 67% del volumen, + 



 F.A. 20W 33% del volumen

SAE 15W



 F.A. 5W 33% del volumen, + 



 F.A. 20W 67% del volumen





-------------------------------------------------------------------------------------------------------------------------------------------------------------

9

- 11

---    -

RS 250 

LÍQUIDO DE FRENOS

Este vehículo está equipado con frenos de
disco delantero y trasero, con circuitos hi-

dráulicos separados. Las siguientes informaciones
se refieren a un solo sistema de frenado, pero tienen
validez incluso para ambos sistemas.

El líquido de frenos puede producir irritacio-
nes si tiene contacto con la piel o con los
ojos. Lávese muy bien las partes del cuerpo

que hayan tenido contacto con el líquido y diríjase a
un oftalmólogo o a un médico si el líquido entrara en
contacto con los ojos. 

NO ESPARZA EL LÍQUIDO EN EL MEDIO AMBIENTE.

MANTÉNGASE LEJOS DEL ALCANCE DE LOS NI-
ÑOS

Utilizando el líquido de los frenos, tenga cui-
dado con no verterlo sobre las partes de plás-
tico y pintadas porque podría dañarlas.

Controle cada 1000 km (625 mi) el líquido frenos, véa-
se pág. 2-30 (FRENOS); substitúyalo cada año.

Líquido de frenos (aconsejado):



 F.F. DOT 5 (Compatible DOT 4)

Para no dañar el sistema de frenado, no utilice
líquidos diferentes de aquéllos indicados y no
los mezcle para rellenar.

No utilice líquidos de frenos que hayan estado en re-
cipientes viejos o ya abiertos. No use líquidos de fre-
nos que hayan sobrado de reparaciones anteriores,
si ya ha pasado mucho tiempo.
Variaciones imprevistas del juego o la resistencia
elástica sobre las palancas de los frenos, se deben a
incovenientes en el sistema hidráulico.
Tenga cuidado que los discos de freno y las pastillas
de freno no estén untadas o engrasadas, especial-
mente tras las operaciones de mantenimiento o de
control. Controle que los tubos de los frenos no es-
tén estrangulados o desgastados.
Tenga cuidado que no entre accidentalmente  agua o
polvo en el interior del circuito.

En caso de intervenciones de mantenimiento en el
circuito hidráulico, se aconseja use guantes de látex.

LÍQUIDO REFRIGERANTE

El líquido refrigerante es nocivo si es tragado;
si llega a contacto con la piel o con los ojos
podría causar irritaciones. Si el líquido llegara

a contacto con la piel o los ojos, lávelos con mucha
agua y diríjase a un médico. 
De tragarlo accidentalmente, produzca el vómito, en-
juáguese la boca y la garganta con mucha agua y di-
ríjase inmediatamente a un médico.

NO ESPARZA EL LÍQUIDO EN EL MEDIO AMBIENTE.

MANTÉNGASE LEJOS DEL ALCANCE DE LOS NI-
ÑOS

Tenga cuidado con no verter el líquido refrige-
rante sobre las piezas candentes del motor;
podría incendiarse emitiendo llamas invisi-

bles.

En caso de intervenciones de mantenimiento, se
aconseja usar guantes de látex.

No quite la tapa del depósito de expansión con el mo-
tor caliente ya que el líquido refrigerante está bajo
presión y a temperatura elevada.

No utilice el vehículo si el nivel del líquido refrigeran-
te está por debajo del nivel mínimo.

Controle el líquido refrigerante cada 2000 km (1250 mi),
substitúyalo cada dos años, véase pág. 2-24 (SISTEMA
DE REFRIGERACIÓN).

La solución del líquido refrigerante está compuesta por un
50% de agua y un 50% de anticongelante. Esta mezcla es
ideal para casi todas las temperaturas de funcionamiento y
garantiza una buena protección contra la corrosión.

Se aconseja mantener la misma mezcla incluso durante el
verano pues, de esta manera, se reducen las pérdidas por
evaporación y no es necesario rellenar frecuentemente.
De esta manera disminuyen los depósitos de sales mine-
rales que deja el agua evaporada en el radiador y se man-
tiene inalterada la eficacia del sistema de refrigeración.

En caso de que la temperatura exterior fuera inferior a
cero grados centígrados, controle frecuentemente el cir-
cuito de refrigeración añadiendo, si es necesario, una
mayor concentración de anticongelante (hasta un máxi-
mo del 60%).

Para no arruinar el motor, usar agua destilada para la so-
lución refrigerante.

Líquido refrigerante (aconsejado): 



 ECOBLU -40°

De acuerdo con la temperatura de congelamiento de la
mezcla refrigerante que se quiere obtener, agregue al
agua, el porcentaje de líquido refrigerante indicado por la
siguiente tabla:

Las características de los diferentes líquidos
anticongelantes son distintas. Lea en la eti-

queta del producto, cuál es el grado de protección
que garantiza.

Utilice sólo anticongelante y antioxidante sin
nitrito, que proteja por lo menos hasta -35 °C.









Punto

de congelamiento °C

Líquido refrigerante 

% del volumen

-20°

35

-30°

45

-40°

55









-------------------------------------------------------------------------------------------------------------------------------------------------------------

 -  ---

9

- 12

RS 250 

TRANSMISSION OIL

The oil can cause serious damage to the skin
if handled every day and for long periods.
Wash your hands carefully after using the oil.

Do not dispose of the oil in the environment.
Put it in a sealed container and take it to the filling
station where you usually buy it or to an oil salvage
center.

In case any maintenance operation has to be carried
out, it is advisable to use latex gloves.

Check the transmission oil level every 4000 km (2500
mi), see p. 2-22 (GEAR OIL).

Change the transmission oil after the first 1000 km (625
mi) and successively every 12000 km (7500 mi), see
p. 2-22 (GEAR OIL).

Transmission oil (recommended):



 F.C. SAE 75W - 90.

As an alternative to the recommended oil, it is possible to
use high-quality oils with characteristics in compliance
with or superior to the A.P.I. GL-4.

MIXER OIL

Use synthetic oil with ISO-L-ETC++A.P.I. TC++ specifica-
tions for unleaded gasoline.

Mixer oil (recommended):



 MAX 2T COMPETITION.

This oil is formulated to give best engine performance
with least combustion chamber deposits, least preigni-
tion, maximum spark plug life and best lubrication.

FORK OIL

Fork oil may cause serious damage to the skin
if handled daily and for long periods.  
It is advisable to wash your hands thoroughly

after using. 
Do not dispose of oil in the environment.  
Deliver it to or have it collected by the nearest used
oil recovery firm or by the supplier.

In case any maintenance operation has to be carried
out, it is advisable to use latex gloves.

By changing the setting of the damping elements
and/or the viscosity of the oil they contain, it is possi-
ble to partially vary the response of the suspension.

Standard oil viscosity: SAE 20W.



 F.A. is available in two discosity degrees that can

be chosen according to the kind of vehicle attitude
required (SAE 5W soft, 20W rigid).

It is possible to use the two products in variable per-
centages until obtaining the desired response.

The viscosity of 



 F.A. does not depend on its tem-

perature excessively and therefore its damping re-
sponse is almost constant.

Recommended fork oil: 



 F.A. 5W or 



 F.A. 20W fork

oil.
If an intermediate performance is desired (between those
of 



 F.A. 5W and IP F.A. 20W, the products can be

mixed as follows:

SAE 10W



 F.A. 5W 67% of volume, + 



 F.A. 20W 33% of volume

SAE 15W



 F.A. 5W 33% of volume, + 



 F.A. 20W 67% of volume





-------------------------------------------------------------------------------------------------------------------------------------------------------------

9

- 13

 -  ---

RS 250 

BRAKE FLUID

This vehicle is provided with front and rear
disc brakes, with separate hydraulic circuits.

The following information refers to a single braking
system, but is valid for both.

Brake fluid may cause irritation if it comes into
contact with the skin or eyes. 
Carefully wash the part of the body that has

come into contact with the fluid.
Consult an oculist or a physician if the fluid comes
into contact with your eyes.

DO NOT DISPOSE OF BRAKE FLUID IN THE ENVI-
RONMENT.

KEEP BRAKE FLUID AWAY FROM CHILDREN

When using the brake fluid, take care not to
spill it on the plastic or painted parts, since it
can damage them.

Check every 1000 km (625 mi) the brakes fluid level;
see p. 2-30 (BRAKES); change it every year.

Recommended brake fluid:



 F.F. DOT 5 (compatible DOT 4)

To avoid serious damage to the braking sys-
tem, do not use fluids other than the recom-
mended ones nor mix different fluids for top-

ping up.
Do not use brake fluid taken from old or already
opened containers.  Do not use brake fluid left from
previous repairs if they were done some time ago.
Sudden variations in clearance or an elastic resist-
ance in the brake levers may be due to trouble in the
hydraulic circuits.
Make sure that the brake discs and the friction pads
are completely free of grease or oil, especially after
maintenance or checking operations. 
Check that the brake cables are not twisted or worn.
Make sure that neither water nor dust accidentally en-
ter the circuit.

In case maintenance operations are to be performed
on the hydraulic circuit, it is advisable to use latex
gloves.

COOLANT

The coolant is noxious: do not swallow it; if
the coolant gets in contact with the skin or the
eyes, it can cause serious irritations. If the

coolant gets in contact with your skin or eyes, rinse
with plenty of water and consult a doctor. If it is swal-
lowed, induce vomit, rinse mouth and throat with
plenty of water and consult a doctor without delay.

DO NOT DISPOSE OF BRAKE FLUID IN THE ENVI-
RONMENT.

KEEP BRAKE FLUID AWAY FROM CHILDREN

Be careful not to spill the coolant on the red-
hot parts of the engine: it may catch fire and
send out invisible flames.

In case maintenance operations are to be performed,
it is advisable to use latex gloves.

Do not remove the expansion tank cap when the en-
gine is hot as the coolant is under pressure and at a
very high temperature.

Do not use vehicle if the coolant level is below the
minimum prescribed.

Check coolant level every 2000 km (1250 mi) and change
it every 2 years, see p. 2-24  (COOLING SYSTEM).

The coolant is composed of 50% water and 50% anti-
freeze. This mixture is ideal for most running tempera-
tures and ensures good protection against corrosion.  

It is advisable to keep the same mixture in the hot season
as well, since in this way losses due to evaporation are
reduced and it is not necessary to top up so frequently.
The mineral salt deposits left in the radiator by evaporat-
ed water are thus lessened and the efficiency of the cool-
ing system remains unaltered.

If the outdoor temperature is below 0°, check th cooling
circuit frequently and inf necessary increase the anti-
freeze concentration (up to maximum 60%).

Use distilled water for the cooling solution so as not to
damage the engine.

Recommended coolant: 



 ECOBLU -40°

On the basis of the desired freezing temperature of the
coolant mixture, add to the water the percentage of cool-
ant indicated in the following table:

The characteristics of the various antifreeze
liquids are different. Be sure to read the label

on the product to learn the degree of protection it
guarantees.

Use only antifreeze and anticorrosive without
nitrite in order to ensure protection at at least
-35°C.









Freezing point

°C

Coolant

of the volume % 

-20°

35

-30°

45

-40°

55









-------------------------------------------------------------------------------------------------------------------------------------------------------------

9

- 15

---    -

RS 250 

-

El rodaje del motor es fundamental para garantizar una
larga duración y un correcto funcionamiento. 
Recorra, si es posible, carreteras con muchas curvas y/o
onduladas para someter el motor, las suspensiones y los
frenos a un rodaje más eficaz. Durante el rodaje, varíe la
velocidad de conducción para permitir “cargar” el trabajo
de los componentes y sucesivamente “descargarlo”, en-
friando las piezas del motor. Aunque sea importante soli-
citar los componentes del motor durante el rodaje, ponga
mucho cuidado en no exagerar.

Sólo tras los primeros 1500 km (937 mi) de ro-
daje se pueden obtener las mejores prestacio-

nes del vehículo.

Siga las siguientes indicaciones:



No acelere bruscamente y del todo cuando el motor

está en función con un bajo régimen de revoluciones,
sea durante que después del rodaje. 



Durante los primeros 100 km (62 mi), actúe con cuida-

do sobre los frenos y evite frenazos repentinos y pro-
longados.
Todo esto para permitir un ajuste correcto del material
de fricción de las pastillas sobre los discos del freno.



Durante los primeros 800 km (500 mi) de recorrido, no

supere nunca las 6000 rpm.

Tras los primeros 1000 km (625 mi) de funcio-
namiento haga realizar los controles indica-
dos en la columna “fin rodaje” de la FICHA DE

MANTENIMIENTO PERIÓDICO, véase pág. 9-25 (FI-
CHA DE MANTENIMIENTO PERIÓDICO), a fin de evi-
tar daños a sí mismo, a los demás y/o al vehículo.



Entre los 800 km (500 mi) y los 1600 km (1000 mi) de

recorrido, conduzca más vivamente, varíe la velocidad
y utilice la máxima aceleración sólo durante ratos bre-
ves, para permitir un mejor acoplamiento de los compo-
nentes; no supere las 9000 rpm del motor (véase ta-
bla).



Tras los primeros 1600 km (1000 mi) se pueden exigir

mayores prestaciones del motor; sin embargo, las re-
voluciones del motor no deben superar el régimen
máximo permitido (12000 rpm).

     - 

 

Cuando realice la reparación, el desmontaje o el remon-
taje del vehículo, aténgase escrupulosamente a los si-
guientes consejos.

Está prohibido utilizar llama viva para cual-
quier tipo de operación.
Antes de empezar cualquier tipo de interven-

ción de mantenimiento o inspección en el vehículo,
apague el motor y quite la llave, espere a que el motor
y el sistema de escape se hayan enfríado; si es posi-
ble levante el vehículo mediante un equipo adecuado,
sobre un piso sólido y nivelado.
En particular, preste atención a las piezas del motor y
del sistema de escape que aún estén calientes, para
evitar quemaduras. El vehículo está fabricado con
piezas no comestibles. Por ninguna razón, muerda,
chupe, mastique ni trague ninguna pieza del mismo.
Si no está indicado expresamente, la reinstalación de
los grupos se realiza en el sentido contrario al de las
operaciones de desmontaje.
No haga funcionar el motor en locales cerrados o
poco ventilados.
Maneje el combustible con mucho cuidado.
Nunca utilice el combustible como disolvente para
limpiar el vehículo.
En el caso de que deba efectuar soldaduras eléctri-
cas, desconecte el cable negativo (–) de la batería.
Cuando dos o más personas trabajan simultánea-
mente, preste atención a la seguridad de cada una de
ellas.

– Utilice exclusivamente REPUESTOS ORIGINALES

aprilia.

– Utilice los lubricantes aconsejados.
– Utilice, en donde está previsto, las herramientas espe-

ciales 



 proyectadas para este vehículo.

– Utilice siempre el caballete central si el vehículo está

equipado con éste.

– Para llevar a cabo algunas intervenciones, es aconseja-

ble utilizar un caballete 



 para sostener el vehículo en

posición vertical.

– Al apretar los tornillos y las tuercas, empiece por los

que tienen el diámetro mayor o por los que están en el
interior, siguiendo en diagonal.
Apriete con pasajes sucesivos antes de aplicar el par
de apriete.

– Limpie y lave cuidadosamente con detergente de bajo

nivel de inflamabilidad, los componentes desmontados.

– Lubrique las piezas (cuando es posible) antes de reins-

talarlas.

– Controle que cada componente haya sido montado co-

rrectamente.

– Siempre substituya las juntas, anillos aislantes, anillos

elásticos, juntas tóricas (OR) y grupillas por otros nue-
vos.

– Marque la posición sobre todos los empalmes de co-

nexión (tubos, cables, etc.) antes de soltarlos e identifí-
quelos con signos distintos. 
Hay que marcar claramente cada pieza para poder
identificarla en fase de instalación.

Los cojinetes deben girar libremente, sin tropiezos
ni/o ruidos, en caso contrario deben substituirse.

No vuelva a utilizar nunca un anillo elástico,
cuando se desmonta hay que sustituirlo con
otro nuevo. Cuando se monta un anillo elástico

nuevo, tenga cuidado en no estirar los extremos más
de lo necesario para introducirlo en el eje.
Tras haber montado un anillo elástico, controle que
esté total y firmemente introducido en su alojamiento.

Números máximos de revoluciones 

del motor recomendados

Recorrido km (mi)

rpm

0÷800 (0÷500)

6000

800÷1600 (500÷1000)

9000

oltre 1600 (1000)

12000









-------------------------------------------------------------------------------------------------------------------------------------------------------------

 -  ---

9

- 16

RS 250 

  

The running-in of the engine is important to ensure its
correct functioning.
If possible, drive on hilly roads and/or roads with many
bends, so that the engine, the suspensions and the
brakes undergo a more effective running-in. 
During running-in, change speed. In this way the compo-
nents are first ìloadedî and then ìrelievedî and the en-
gine parts can thus cool down. Even if it is important to
stress the engine components during running-in, take
care not to exceed.

Only after the first 1500 km (937 mi) of run-
ning-in you can expect the best performance

levels from the vehicle.

Keep to the following indications:



Do not open the throttle completely if the speed is low,

both during and after the running-in.



During the first 100 km (62 mi) put on the brakes with

caution, avoiding sharp and prolonged brakings. 
This ensures a correct bedding-in of the pads on the
brake disc.



During the first 800 km (500 mi) never exceed 6000

rpm.

After the first 1000 km (625 mi), carry out the
checks indicated in the column “After run-
ning-in” of the REGULAR SERVICE INTER-

VALS CHART, see p. 9-25 (PERIODIC SERVICE
CHART FOR THE COMPONENTS), in order to avoid
hurting yourself or other people and/or damaging the
vehicle.



Between the first 800 km (500 mi) and 1600 km (1000

mi) drive more briskly, change speed and use the max-
imum acceleration only for a few seconds, in order to
ensure better coupling of the components; never ex-
ceed 9000 rpm (see table).



After the first 1600 km (1000 mi) you can expect better

performance from the engine, however, without ex-
ceeding the maximum allowed  rpm (12000 rpm).

-   -      --

Follow with care these recommendations when repairing,
disassembling and reassembling the vehicle.

The use of naked flames is forbidden for any
type of operation.
Before commencing any service or inspection

operation on the vehicle, switch off the engine and
remove the key,  wait until the engine and the exhaust
system have cooled down and, if possible, raise the
vehicle with the suitable equipment onto firm flat
ground.
In order to avoid burns, be careful not to touch any
parts of engine or exhaust system which have not
cooled down completely.
The vehicle is constructed of inedible parts. 
Do not bite, suck, chew or swallow any part of the ve-
hicle for any reason whatever.
If not expressly described,  the reassembly of the
units is carried out by reversing the order of opera-
tions. Do not run the engine in closed or badly venti-
lated places.
Handle fuel with the greatest caution.
Never use fuel as a solvent for cleaning the vehicle.
Disconnect the negative cable (–) from the battery
when electric welding.
When two or more persons are working together,
make sure that each is working in safe conditions.

– Use only original aprilia SPARE PARTS.
– Use the recommended lubricants.
– Use, when necessary, the special tools 



 designed

for this vehicle.

– Always use the centre stand, if the vehicle is provided

with it.

– In order to carry out certain interventions we recom-

mend using a  stand 



 to hold the vehicle in a vertical

position.

– When tightening screws and nuts, begin with those

having greater diameters or with inner ones, proceed-
ing diagonally.
Tighten screws or nuts in successive passages before
applying driving torque.

– Clean and wash carefully any disassembled parts with

low inflammability detergents.

– Whenever possible, lubricate the parts before reas-

sembly.

– Make sure that each component has been reassem-

bled correctly.

– Always replace gaskets, grommets, circlips, O-rings

and split pins with new ones.

– Before disconnecting the joints (pipes, cables, etc.),

mark the positions on all of them and mark them with
different distinguishing signs.
Each piece must be marked clearly, in order not to
have problems during installation.

The bearings must rotate freely, without  halting a/o
noise otherwise they must be replaced.

Never use a circlip twice. When a circlip is re-
moved, it must be replaced with a new one.
When assembling a new circlip be careful not

to stretch its ends more than strictly necessary to put
it on the shaft.
After installing a circlip, make sure that it is com-
pletely and firmly inserted  in its seat.

Engine maximum rpm 

recommended

Mileage km (mi)

rpm

0÷800 (0÷500)

6000

800÷1600 (500÷1000)

9000

oltre 1600 (1000)

12000









-------------------------------------------------------------------------------------------------------------------------------------------------------------

9

- 17

---   -   ---    -     -  ---

RS 250 

 -  -

En caso de substitución, utilice sólo
Repuestos Originales aprilia. Los Re-
puestos Originales aprilia son de alta
calidad, proyectados y fabricados ex-
presamente oara vehículos aprilia.

Utilizar repuestos NO origi-
nales 

 !"!

, puede causar

daños y problemas de rendi-

mientos.



- 



   -

For any replacement, use aprilia Gen-
uine Spare Parts only. 
aprilia Genuine Spare Parts are high-
quality parts, expressly designed and
manufactured for aprilia vehicles.

Failure to use 

 !"!

 Genu-

ine Spare Parts may result in
incorrect performance and

damages.

- 

 - 



- - -

In caso di sostituzione, utiizzare solo
Ricambi Originali aprilia
I Ricambi Originali aprilia sono di alta
qualità, progettati e costruiti espressa-
mente per i veicoli aprilia.

L’impiego di ricambi NON
originali 

 !"!

 può causare

problemi di prestazioni e

danneggiamenti.

---

- 

DIMENSIONI / 

DIMENSIONES

 / DIMENSIONS

Lunghezza max / 

Longitud máx.

 / Max. length

1975 mm

Larghezza max / 

Anchura máx. 

/ Max. width

690 mm

Altezza max (al cupolino) / 

Altura máx. (hasta la cúpula)

 /

Max. height (front part of the fairing included)

1180 mm

Altezza alla sella / 

Altura hasta el sillín 

/ Saddle height

810 mm

Interasse / 

Distancia entre los ejes

 / Distance between centres

1360 mm

Altezza libera minima dal suolo / 

Altura libre mínima del suelo

 / Min. ground clear-

ance

135 mm

Peso in ordine di marcia / 

Peso en orden de marcha

 / Weight ready for starting

167 kg

MOTORE

 / MOTOR / ENGINE

Tipo / 

Tipo 

/ Type

Bicilindrico a V di 90° 2 tempi con aspirazione lamellare
e valvola alla luce di scarico. Lubrificazione separata con
miscelatore automatico a titolo variabile (0,9 - 2%) / 

Bicilíndrico en V de 90° de 2 tiempos con aspiración
laminar y válvula en la abertura de escape. Lubricación
separada con mezclador automático de flujo variable
(0,9 - 2%) 

/ 90°V two-cylinder with laminar suction and

valve on the exhaust port. Separate lubrication with
automatic, variable oil titer mixer (0.9-2%).

Numero cilindri / 

Número cilindros

 / Number of cylinders

2

Cilindrata complessiva / 

Cilindrada total

 / Total displacement

249,25 cm



Alesaggio e corsa / 

Diámetro y carrera 

/ Bore and stroke

56 mm / 50,6 mm

Rapporto di compressione / 

Relación de compresión 

/ Compression ratio

12 ± 0,7 : 1

Avviamento / 

Arranque

 / Starting

a pedale / 

por pedal

 / 

With pedal

N° giri del motore al minimo / 

N° revoluciones del motor al mínimo

 / Idling engine 1300 ± 100 giri/min / 

rpm

 / rpm 

Frizione / 

Embrague 

/ Clutch

multidisco in bagno d’olio con comando a mano sul lato
sinistro del manubrio / 

multidisco en baño de aceite con mando manual en el
lado izquierdo del manillar / 

multidisc in oil bath, with

manual control on the left side of the handlebar

Cambio / 

Cambio

 / Change gear

meccanico a 6 rapporti con comando a pedale sul lato
sinistro del motore / 

mecánico con 6 relaciones con mando de pedal en el
lado izquierdo del motor 

/

 

mechanical, 6 gears with foot control on the left side of
the engine

Raffreddamento / 

Refrigeración 

/ Cooling

a liquido / 

por líquido

 / liquid-cooled

Filtro aria / 

Filtro aire

 / Air filter

con elemento filtrante in poliuretano / 

con elemento fil-

trante de poliuretano

 / with polyurethane filter element

Sistema di lubrificazione / 

Sistema de lubricación

 / Lubrication system

pompa olio con circuito separato / 

bomba del aceite

con circuito separado

 / oil pump with separate circuit 

CAPACITÀ / 

CAPACIDAD

 / CAPACITY

Carburante (inclusa riserva) / 

Combustible (reserva incluida)

 / 

Fuel (reserve included)

19,5



Riserva carburante / 

Reserva combustible

 / Fuel reserve

3,6 



(riserva meccanica) / 

3,6 



(reserva mecánica) / 

3.6 



(mechanical reserve)

Olio miscelatore (inclusa riserva) / 

Aceite mezclador (reserva incluida)

 / 

Mixer oil (reserve included)

1,6 



Riserva olio miscelatore / 

Reserva aceite mezclador

 / Mixer oil reserve

0,3 



Olio cambio / 

Aceite cambio

 / Change gear oil

700 cm



Olio forcella (stelo destro e stelo sinistro) / 

Aceite horquilla (barra derecha y 

barra izquierda) 

/ Fork oil (right fork tube and left fork tube)

431 cm



Liquido refrigerante / 

Líquido refrigerante

 / Coolant

1,9 



(50% acqua + 50% antigelo con glicole etilenico)

1,9 



(50% agua + 50% anticongelante con glicol etilénico)

1.9 



(50% water + 50% antifreeze with ethylene glycol)

Posti / 

Asientos

 / Seats

2

MAX CARICO VEICOLO / 

MÁX. CARGA VEHÍCULO

 / VEHICLE MAX. LOAD

(pilota + passeggero + bagaglio) / 

(piloto + pasajero + equipaje)

 /

(driver + passenger + luggage)

160 kg



-------------------------------------------------------------------------------------------------------------------------------------------------------------

 

 

 

 

 

 

 

Content   ..  27  28  29  30   ..