Nissan Versa Sedan. Manual - part 860

TM-346

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

P0705 TRANSMISSION RANGE SENSOR A

2. Disconnect  TCM connector.

3. Check  continuity between  TCM harness connector terminals.

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Repair or replace malfunctioning parts.

7.

CHECK P POSITION SW CIRCUIT (PART 2)

1. Disconnect  transmission position switch connector.

2. Turn ignition switch ON.

3. Check  voltage between  TCM harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 12.

NO

>> Repair or replace malfunctioning parts.

8.

CHECK R POSITION SW CIRCUIT (PART1)

1. Turn  ignition switch OFF.

2. Disconnect  TCM connector.

3. Check  continuity between  TCM harness connector terminals.

Is the inspection result normal?

YES

>> GO TO 9.

NO

>> Repair or replace malfunctioning parts.

9.

CHECK R POSITION SW CIRCUIT (PART 2)

1. Disconnect  transmission position switch connector.

2. Turn ignition switch ON.

3. Check  voltage between  TCM harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 12.

NO

>> Repair or replace malfunctioning parts.

TCM

Continuity

Connector

Terminal

F44

7

2

Not existed

4

5

6

TCM

Ground

Voltage

Connector

Terminal

F44

7

Ground

Approx. 0 V

TCM

Continuity

Connector

Terminal

F44

6

2

Not existed

4

5

7

TCM

Ground

Voltage

Connector

Terminal

F44

6

Ground

Approx. 0 V

P0705 TRANSMISSION RANGE SENSOR A

TM-347

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

10.

CHECK L POSITION SWITCH CIRCUIT (PART 1)

1. Turn  ignition switch OFF.

2. Disconnect  TCM connector.

3. Check  continuity between  TCM harness connector terminals.

Is the inspection result normal?

YES

>> GO TO 11.

NO

>> Repair or replace malfunctioning parts.

11.

CHECK L POSITION SWITCH CIRCUIT (PART 2)

1. Disconnect  transmission position switch connector.

2. Turn ignition switch ON.

3. Check  voltage between  TCM harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 12.

NO

>> Repair or replace malfunctioning parts.

12.

CHECK TRANSMISSION RANGE SWITCH

Check  transmission range switch. Refer to 

TM-347, "Component Inspection (Transmission Range Switch)"

.

Is the check result normal?

YES

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

NO

>> Repair or replace malfunctioning parts.

Component Inspection (Transmission Range Switch)

INFOID:0000000009268150

1.

CHECK TRANSMISSION RANGE SWITCH

Check  continuity between  transmission range switch connector terminals.

TCM

Continuity

Connector

Terminal

F44

2

4

Not existed

5

6

7

TCM

Ground

Voltage

Connector

Terminal

F44

2

Ground

Approx. 0 V

Transmission range switch

Condition

Continuity

Terminal

1 – 2

Manual lever: “P” and “N” positions

Existed

Other than the above

Not existed

3 – 4

Manual lever: “P” position

Existed

Other than the above

Not existed

3 – 5

Manual lever: “R” position

Existed

Other than the above

Not existed

3 – 6

Manual lever: “N position

Existed

Other than the above

Not existed

3 – 7

Manual lever: “D” position

Existed

Other than the above

Not existed

TM-348

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

P0705 TRANSMISSION RANGE SENSOR A

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> There is a malfunction of  transmission range switch. Replace  transaxle assembly. Refer to 

TM-

452, "Removal and Installation"

.

3 – 8

Manual lever: “L” position

Existed

Other than the above

Not existed

Transmission range switch

Condition

Continuity

Terminal

P0706 TRANSMISSION RANGE SENSOR A

TM-349

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

P0706 TRANSMISSION RANGE SENSOR A

DTC Logic

INFOID:0000000009268151

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at

least 10 seconds, then perform the next test.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

1. Start the engine.

2. Maintain the following conditions.

3. Shift the selector lever through entire positions from “P” to “L”. (Hold the selector lever at each position for

35 seconds or more.)

4. Check the first trip DTC.
Is “P0706” detected?

YES

>> Go to 

TM-349, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009268152

1.

ADJUSTMENT OF CONTROL CABLE

Adjust  control cable. Refer to 

TM-430, "Inspection and Adjustment"

.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

1. Turn ignition switch ON.

2. Select “Self Diagnostic Results” in “TRANSMISSION”.

3. Touch “Erase”.

4. Perform "DTC CONFIRMATION PROCEDURE". Refer to 

TM-349, "DTC Logic"

.

Is “P0706” detected?

YES

>> GO TO 3.

NO

>> INSPECTION END

DTC

Trouble diagnosis name

DTC detection condition

Possible causes

P0706

Transmission Range Sensor 
A Circuit Range/Performance

All range signals stay OFF continuously for 30 
seconds under the following diagnosis condi-
tion 1 and 2:
• Diagnosis condition 1 (continued for 30 sec-

onds or more) 

- TCM power supply voltage: More than 11 V
• Diagnosis condition 2 (continued for 2 sec-

onds or more) 

- Vehicle speed: Less than 3 km/h (2 MPH)
- Accelerator pedal position: 0.6/8 or less
- Idle switch: ON 
- Stop lamp switch: ON

• Harness or connector

(Open circuit between ignition switch 
and transmission range switch/open 
circuit between transmission range 
switch and TCM)

• Transmission range switch
• Control cable

Accelerator pedal position

: 0.0/8

Brake pedal

: Depressed

Vehicle speed

: 0 km/h (0 MPH)