Nissan Versa Sedan. Manual - part 859

TM-342

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

P062F EEPROM

P062F EEPROM

Description

INFOID:0000000009268145

TCM compares the calculated value stored in the flash ROM with the value stored in TCM. If the calculated

value does not agree with the stored value, TCM judges this as a malfunction.

DTC Logic

INFOID:0000000009268146

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at

least 10 seconds, then perform the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

1. Start the engine.

2. Check the DTC.
Is “P062F” detected?

YES

>> Go to 

TM-342, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009268147

1.

CHECK INTERMITTENT INCIDNT

Refer to 

GI-45, "Intermittent Incident"

.

Is the inspection result normal?

YES

>> Replace the TCM. Refer to 

TM-437, "Removal and Installation"

.

NO

>> Repair or replace malfunctioning parts.

DTC

Trouble diagnosis name

DTC detection condition

Possible causes

P062F

Internal Control Module EE-
PROM Error

Flash ROM error is detected when turning ON 
the ignition switch.

• TCM (flash ROM)
• Harness or connector

[TCM power supply (back-up) circuit is 
open or shorted]

P0705 TRANSMISSION RANGE SENSOR A

TM-343

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

P0705 TRANSMISSION RANGE SENSOR A

DTC Logic

INFOID:0000000009268148

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CAUTION:

Be careful of the driving speed.

1.

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at

least 10 seconds, then perform the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

1. Start the engine.

2. Maintain the following conditions.

3. Shift the selector lever through entire positions from “P” to “L”. (Hold the selector lever at each position for

10 seconds or more.)

4. Check the first trip DTC.
Is “P0705” detected?

YES

>> Go to 

TM-343, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009268149

1.

CHECK TCM INPUT SIGNALS

With CONSULT

1. Turn ignition switch ON.

2. Select “Data Monitor” in “TRANSMISSION”.

3. Select “D POSITION SW”, “N POSITION SW”, “R POSITION SW”, “P POSITION SW” and “L POSITION

SW”.

4. Shift the selector lever through entire positions from “P” to “L” and check ON/OFF of each monitor item. 

DTC

Trouble diagnosis name

DTC detection condition

Possible causes

P0705

Transmission Range Sensor 
A Circuit (PRNDL Input)

Two or more range signals simultaneously 
stay ON continuously for 5 seconds under the 
following diagnosis condition 1 and 2: 
• Diagnosis condition 1 (continued for 5 sec-

onds or more) 

- TCM power supply voltage: More than 11 V
• Diagnosis condition 2 (continued for 2 sec-

onds or more) 

- Vehicle speed: Less than 3 km/h (2 MPH)
- Accelerator pedal position: 0.6/8 or less
- Idle switch: ON 
- Stop lamp switch: ON

• Harness or connector

(Short circuit between transmission 
range switch and TCM)

• Transmission range switch

Accelerator pedal position

: 0.0/8

Brake pedal

: Depressed

Vehicle speed

: 0 km/h (0 MPH)

Monitor item

Test condition

Condition

D POSITION SW

Selector lever: “D” position

On

Other than the above

Off

TM-344

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

P0705 TRANSMISSION RANGE SENSOR A

 Without CONSULT

1. Turn  ignition switch OFF.

2. Disconnect  TCM connector.

3. Turn ignition switch ON.

4. Shift the selector lever from “P” to “L” and check  voltage between  TCM harness connector terminals and

ground. 

Is the inspection result normal?

YES >> Check 

intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

NO-1 [“D POSITION SW” is “ON” when selector is not in “D” position. (Or connector terminal 4 is at power

voltage.)]>>GO TO 2.

NO-2 [“N POSITION SW” is “ON” when selector is not in “N” position. (Or connector terminal 5 is at power

voltage.)]>>GO TO 4.

NO-3 [“R POSITION SW” is “ON” when selector is not in “R” position. (Or connector terminal 6 is at power

voltage.)]>>GO TO 6.

NO-4 [“P POSITION SW” is “ON” when selector is not in “P” position. (Or connector terminal 7 is at power

voltage.)]>>GO TO 8.

NO-5 [“L POSITION SW” is “ON” when selector is not in “L” position. (Or connector terminal 2 is at power

voltage.)]>>GO TO 10.

2.

CHECK D POSITION SW CIRCUIT (PART 1)

1. Turn  ignition switch OFF.

2. Disconnect  TCM connector.

3. Check  continuity between  TCM harness connector terminals.

N POSITION SW

Selector lever: “N” position

On

Other than the above

Off

R POSITION SW

Selector lever: “R” position

On

Other than the above

Off

P POSITION SW

Selector lever: “P” position

On

Other than the above

Off

L POSITION SW

Selector lever: “L” position

On

Other than the above

Off

TCM

Ground

Test condition

Voltage

Connector

Terminal

F44

2

Ground

Selector lever: “ L” position

Battery voltage

Other than the above

Approx. 0 V

4

Selector lever: “D” position

Battery voltage

Other than the above

Approx. 0 V

5

Selector lever: “N” position

Battery voltage

Other than the above

Approx. 0 V

6

Selector lever: “R” position

Battery voltage

Other than the above

Approx. 0 V

7

Selector lever: “P” position

Battery voltage

Other than the above

Approx. 0 V

Monitor item

Test condition

Condition

P0705 TRANSMISSION RANGE SENSOR A

TM-345

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace malfunctioning parts.

3.

CHECK D POSITION SW CIRCUIT (PART 2)

1. Disconnect  transmission position switch connector.

2. Turn ignition switch ON.

3. Check  voltage between  TCM harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 12.

NO

>> Repair or replace malfunctioning parts.

4.

CHECK N POSITION SW CIRCUIT (PART 1)

1. Turn  ignition switch OFF.

2. Disconnect  TCM connector.

3. Check  continuity between  TCM harness connector terminals.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace malfunctioning parts.

5.

CHECK N POSITION SW CIRCUIT (PART 2)

1. Disconnect  transmission position switch connector.

2. Turn ignition switch ON.

3. Check  voltage between  TCM harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 12.

NO

>> Repair or replace malfunctioning parts.

6.

CHECK P POSITION SW CIRCUIT (PART 1)

1. Turn  ignition switch OFF.

TCM

Continuity

Connector

Terminal

F44

4

2

Not existed

5

6

7

TCM

Ground

Voltage

Connector

Terminal

F44

4

Ground

Approx. 0 V

TCM

Continuity

Connector

Terminal

F44

5

2

Not existed

4

6

7

TCM

Ground

Voltage

Connector

Terminal

F44

5

Ground

Approx. 0 V