Isuzu D-Max / Isuzu Rodeo (TFR/TFS). Manual - part 263

19

Program immobilizer ICU (Diesel Engine Model)

1. Select “Body” and “Immobilizer”.

2. See immobilizer status on the display of Tech 2.

3. Select engine type.

4. Enter the security code.

5. See ECM status.

6. Input the security code, then press the soft key of “Okay” or “Not Okay”.

Security Code

0000

Press ENTER Key to continue

Not

Okay

Okay

CAUTION

7. Enter VIN.

Vehicle Identification Number:

00000000000000000

Press ENTER Key to continue

Not

Okay

Okay

Enter VIN Input Screen

8. Enter Mechanical key number.

Mechanical Key Number:

- - - - - - -

Press ENTER Key to continue

Not

Okay

Okay

Enter Key No. Input Screen

20

9. Turn ON ignition.

Ignition Status                                        Off  0V

 

Turn Ignition On!

Turn On Ignition

10. See the programming result.

Tech 2 displays the result of programming as the following.
Follow those instructions.

Selected Programming is not possible due to wrong System Status!
Immobilizer Not Programmed!
Immobilizer Already Programmed!
ECM Not Programmed!
ECM Already Programmed!

11. Transponder key must be reprogrammed, because all transponder information is erased

when ICU is programmed. See Transponder programming.

Program ECM

1. Procedure is the same as Program Immobilizer ICU procedure steps 1 through 5.

2. Turn On Ignition.

3. Select an Engine system.

4. See the display of programming result.

Program ECM / Immobilizer ICU

Caution:

1) Do not replace ICU and ECM at the same time.
2) Change ICU at first or ECM and other one change follows.

Follow Program Immobilizer ICU steps 1 through 6, procedure is the same as program

Immobilizer ICU procedure steps 1 through 6.

1. Input the security code.

2. Enter VIN.

3. Enter Key No.

4. Select an engine system.

See programming result display and follow instructions of the display.

5. Transponder key must be reprogrammed, because all transponder information on ICU is Erased when

ICU is programmed. See Transponder programming.

6. Follow program ECM steps 1 through 8.

21

Program Diesel Cutoff Solenoid

NOTE:

Perform this function only when the Immobilizer C/U is replaced.

1. Select "Body" and "Immobilizer".

2. Select engine type.

3. See Immobilizer status on the display of Tech 2.

4. Enter the security code.

5. See ECM or PCM status.

6. Select "F3: Program Diesel Cutoff Solenoid".

Programming

F0: Program Immobilizer Function

F1: Program Transponder-Keys

F2: Program Mechanical Key Number

F3: Program Diesel Cutoff Solenoid

7. Confirm the following screen shows up.

Program Diesel Cutoff Solenoid

See Checking Procedure Before

             Programming!

(1) 2001 (TF) LUV

Electronic System: Immobilizer

Confirm

8. Confirm the following screen shows up.

Program Diesel Cutoff Solenoid

If Battery Voltage Is Low Disconnect

             Fuse For Glow Plugs!

(1) 2001 (TF) LUV

Electronic System: Immobilizer

Confirm

22

9. Turn the ignition switch OFF/ON following the screen.

10. The following screen shows up.

Program Diesel Cutoff Solenoid

(1) 2001 (TF) LUV

Electronic System: Immobilizer

0

100

%

11. Follow the screen procedure.

12. Confirm that there is frequent rattling every 10 seconds.

Program Diesel Cutoff Solenoid

Frequent Rattling Every 10 Seconds?

(1) 2001 (TF) LUV

Electronic System: Immobilizer

NO

YES

13. Confirm the following screen shows up.

Program Diesel Cutoff Solenoid

Reconnect Fuse Glow Plugs!

(1) 2001 (TF) LUV

Electronic System: Immobilizer

Confirm