Toyota Tundra Hybrid (2023 year). Manual in english - page 13

208

4-2. Driving procedures

Turns the brake hold system on

The brake hold standby indica-
tor (green)   comes on. While 
the system is holding the brake, 
the brake hold operated indica-
tor (yellow)   comes on.

■

Brake hold system operating 

conditions

The brake hold system cannot be 

turned on in the following condi-

tions:

●

The driver’s door is not closed.

●

The driver is not wearing the seat 

WARNING

■

When parking the vehicle

Do not leave a child in the vehicle 

alone. The parking brake may be 

released unintentionally by a child 

and there is the danger of the 

vehicle moving that may lead to 

an accident resulting in death or 

serious injury.

■

Parking brake switch

Do not set any objects near the 

parking brake switch. Objects 

may interfere with the switch and 

may lead the parking brake to 

unexpectedly operate.

NOTICE

■

When parking the vehicle

Before you leave the vehicle, shift 

the shift lever to P, set the parking 

brake and make sure that the 

vehicle does not move.

■

When the system malfunc-

tions

Stop the vehicle in a safe place 

and check the warning messages.

■

When the parking brake can-

not be released due to a mal-

function

Driving the vehicle with the park-

ing brake set will lead to brake 

components overheating, which 

may affect braking performance 

and increase brake wear. Have 

the vehicle inspected by your Toy-

ota dealer immediately if this 

occurs.

Brake Hold

The brake hold system 
keeps the brake applied 
when the shift lever is in D, 
S or N with the system on 
and the brake pedal has 
been depressed to stop the 
vehicle. The system 
releases the brake when the 
accelerator pedal is 
depressed with the shift 
lever in D or S to allow 
smooth start off.

Enabling the system

209

4-2. Driving procedures

4

Dr

iv

ing

belt.

●

The parking brake is engaged.

If any of the conditions above are 

detected when the brake hold sys-

tem is enabled, the system will turn 

off and the brake hold standby indi-

cator light will go off. In addition, if 

any of the conditions are detected 

while the system is holding the 

brake, a warning buzzer will sound 

and a message will be shown on the 

multi-information display. The park-

ing brake will then be set automati-

cally.

■

Brake hold function

●

If the brake pedal is left released 

for a period of about 3 minutes 

after the system has started hold-

ing the brake, the parking brake 

will be set automatically. In this 

case, a warning buzzer sounds 

and a message is shown on the 

multi-information display.

●

To turn the system off while the 

system is holding the brake, firmly 

depress the brake pedal and 

press the button again.

●

The brake hold function may not 

hold the vehicle when the vehicle 

is on a steep incline. In this situa-

tion, it may be necessary for the 

driver to apply the brakes. A warn-

ing buzzer will sound and the 

multi-information display will 

inform the driver of this situation. If 

a warning message is shown on 

the multi-information display, read 

the message and follow the 

instructions.

■

When the parking brake is set 

automatically while the system 

is holding the brakes

Perform any of the following opera-

tions to release the parking brake:

●

Depress the accelerator pedal. 

(The parking brake is not released 

if the seat belt is not fastened, 

door is open, and/or the shift lever 

is in P or N.)

●

Operate the parking brake switch 

with the brake pedal depressed.

Make sure that the parking brake 

indicator light goes off. (



P.205)

■

When an inspection at your 

Toyota dealer is necessary

When the brake hold standby indi-

cator (green) does not illuminate 

even when the brake hold switch is 

pressed with the brake hold system 

operating conditions met, the sys-

tem may be malfunctioning. Have 

the vehicle inspected at your Toyota 

dealer.

■

If “Brake Hold Malfunction 

Press Brake to Deactivate Visit 

Your Dealer” or “Brake Hold 

Malfunction Visit Your Dealer” 

is displayed on the multi-infor-

mation display

The system may be malfunctioning. 

Have the vehicle inspected by your 

Toyota dealer.

■

Warning messages and buzzers

Warning messages and buzzers are 

used to indicate a system malfunc-

tion or to inform the driver of the 

need for caution. If a warning mes-

sage is shown on the multi-informa-

tion display, read the message and 

follow the instructions.

■

When another control activates 

with the brake hold system

A message is displayed on the 

multi-information display in any of 

the following cases.

●

“Brake Hold Unavailable, See the 

Owner’s Manual”

• When the brake hold switch is 

pressed while the downhill assist 

control system is activated.

• When the brake hold switch is 

pressed while the front-wheel 

drive control switch is turned to 

“4L” mode.

●

“Brake Hold Unavailable, Press 

Brake to Deactive.”

• When the “DAC/CRAWL” switch is 

operated while the brake hold sys-

tem is activated.

210

4-2. Driving procedures

• When the four-wheel drive control 

switch is turned to “4L” mode 

while the brake hold system is 

activated.

The brake hold system and downhill 

assist control system or transfer 

“4L” mode cannot be activated at 

the same time.
Please press the brake hold switch 

with the brake pedal depressed to 

turn off the brake hold system.

■

If the brake hold operated indi-

cator flashes



P.506

WARNING

■

When the vehicle is on a 

steep incline

Take care when using the brake 

hold system on a steep incline, 

exercise caution. The brake hold 

function may not hold brakes in 

such situations.

Also, the system may not activate 

depending on the angle of the 

slope.

■

When stopped on a slippery 

road

The system cannot stop the vehi-

cle when the gripping ability of the 

tires has been exceeded. Do not 

use the system when stopped on 

a slippery road.

NOTICE

■

When parking the vehicle

The brake hold system is not 

designed for use when parking 

the vehicle for a long period of 

time. Turning the power switch off 

while the system is holding the 

brake may release the brake, 

which would cause the vehicle to 

move. When operating the power 

switch, depress the brake pedal, 

shift the shift lever to P and set 

the parking brake.

211

4-3. Operating the lights and wipers

4

Dr

iv

ing

4-3.Operating the lights and wipers

Operating the 

 switch turns 

on the lights as follows:

U.S.A.

Canada

1

 The side marker, park-

ing, tail, license plate, instru-
ment panel lights, and 
daytime running lights 
(



P.211) turn on.

2

 The headlights and all 

lights listed above (except 
daytime running lights) turn 
on.

3

 The headlights, day-

time running lights (



P.211) 

and all the lights listed above 
turn on and off automatically.

4

 (if equipped) Off

■

AUTO mode can be used when

The power switch is in ON.

■

Daytime running light system

●

On some models: The daytime 

running lights illuminate using the 

same lights as the headlights but 

at a lower intensity.

●

To make your vehicle more visible 

to other drivers during daytime 

driving, the daytime running lights 

turn on automatically when all of 

the following conditions are met. 

(The daytime running lights are 

not designed for use at night.)

• The hybrid system is started

• The parking brake is released
• The headlight switch is in the 

 or 

*

 position

*

: When the surroundings are bright

●

The daytime running lights remain 

on after they illuminate, even if the 

parking brake is set again.

●

For the U.S.A.: Daytime running 

lights can be turned off by operat-

ing the switch.

■

Headlight control sensor

The sensor may not function prop-

erly if an object is placed on the sen-

sor, or anything that blocks the 

sensor is affixed to the windshield.

Doing so interferes with the sensor 

detecting the level of ambient light 

Headlight switch

The headlights can be oper-
ated manually or automati-
cally.

Operating instructions

212

4-3. Operating the lights and wipers

and may cause the automatic head-

light system to malfunction.

■

Automatic light off system

●

When the headlights are on: The 
headlights and tail lights turn off 
30 seconds after the driver’s door 
is opened and closed if the power 
switch is turned to ACC or off. 
(The lights turn off immediately if 

 on the key is pressed after all 

the doors are closed.)

●

When only the tail lights are on: 

The tail lights turn off automati-

cally if the power switch is turned 

to ACC or OFF and the driver’s 

door is opened.

To turn the lights on again, turn the 
power switch to ON, or turn the light 
switch off once and then back to 

 or 

.

■

Light reminder buzzer

A buzzer sounds when the power 

switch is turned to ACC or OFF and 

the driver’s door is opened while the 

lights are turned on.

■

When unlock the doors (wel-

come lamp) (If equipped)

When the doors are unlocked using 

the entry function or wireless remote 

control, the front parking lights and 

tail lights turn on automatically.

When the light switch is in the AUTO 

position and the surrounding area is 

dark, this function will operate.

■

Automatic headlight leveling 

system (if equipped)

The level of the headlights is auto-

matically adjusted according to the 

number of passengers and the load-

ing condition of the vehicle to 

ensure that the headlights do not 

interfere with other road users.

■

Windshield wiper linked head-

light illumination

When driving during daytime with 
the headlight switch turned to 

, if the windshield wipers are 

used, the headlights will turn on 
automatically after several seconds 
to help enhance the visibility of your 
vehicle.

■

12-volt battery-saving function

In order to prevent the 12-volt bat-

tery of the vehicle from discharging, 

if the headlights and/or tail lights are 

on when the power switch is turned 

to OFF the 12-volt battery-saving 

function will operate and automati-

cally turn off all the lights after 

approximately 20 minutes. When 

the power switch is turned to ON, 

the 12-volt battery-saving function 

will be disabled. 

When any of the following are per-

formed, the 12-volt battery-saving 

function is canceled once and then 

reactivated. All the lights will turn off 

automatically 20 minutes after the 

12-volt battery-saving function has 

been reactivated:

●

When the headlight switch is oper-

ated

●

When a door is opened or closed

■

Customization

Some functions can be customized. 

(



P.561)

NOTICE

■

To prevent 12-volt battery dis-

charge

Do not leave the lights on longer 

than necessary when the hybrid 

system is not operating.

213

4-3. Operating the lights and wipers

4

Dr

iv

ing

1

With the headlights on, push 
the lever away from you to 
turn on the high beams.

Pull the lever toward you to the 
center position to turn the high 
beams off.

2

Pull the lever toward you and 
release it to flash the high 
beams once.

You can flash the high beams with 
the headlights on or off.

The vehicle is equipped with 
manual leveling of the head-
lamps. The aim of the head-
lamps can be adjusted by 
adjusting the dial settings based 
on your vehicle loading condi-
tion.
It is recommended that the 
headlamps remain adjusted as 
close to “0” position so not to 
interfere with other road users.

1

Raises the level of the head-
lights

2

Lowers the level of the head-
lights

Turning on the high beam 
headlights

Manual headlight leveling 
dial (if equipped)

214

4-3. Operating the lights and wipers

1

*1

 or 

*2

 Turns the 

front fog lights off

2

 Turns the front fog lights 

on

*1

:U.S.A.

*2

:Canada

■

Fog lights can be used when

The parking lights are on or the 

headlights are on in low beam.

*

: If equipped

1

Press the Automatic High 
Beam switch.

Fog light switch

The fog lights secure excel-
lent visibility in difficult driv-
ing conditions, such as in 
rain and fog.

Operating instructions

AHB (Automatic High 

Beam)

*

The Automatic High Beam 
uses an in-vehicle front 
camera to assess the bright-
ness of streetlights, the 
lights of vehicles ahead etc., 
and automatically turns the 
high beam on or off as nec-
essary.

WARNING

■

Limitations of the Automatic 

High Beam

Do not overly rely on the Auto-

matic High Beam. Always drive 

safely, taking care to observe your 

surroundings and turning the high 

beams on or off manually if nec-

essary.

■

To prevent incorrect opera-

tion of the Automatic High 

Beam system

Do not overload the vehicle.

Activating the Automatic 
High Beam

215

4-3. Operating the lights and wipers

4

Dr

iv

ing

2

Turn the headlight switch to 
the 

 or 

 position.

When the headlight switch lever is 

in the low beam position, the AHB 

system will be enabled and the 

AHB indicator will illuminate.

■

High beam automatic turning 

on or off conditions

●

When all of the following condi-

tions are fulfilled, the high beam 

will be automatically turned on 

(after approximately 1 second):

• Vehicle speed is above approxi-

mately 21 mph (34 km/h) or more.

• The area ahead of the vehicle is 

dark.

• There are no vehicles ahead with 

headlights or tail lights turned on.

• There are few streetlights on the 

road ahead.

●

If any of the following conditions 

are fulfilled, the high beam will be 

automatically turned off:

• Vehicle speed drops below 

approximately 17 mph (27 km/h).

• The area ahead of the vehicle is 

not dark.

• Vehicles ahead have headlights or 

tail lights turned on.

• There are many streetlights on the 

road ahead.

■

Front camera detection infor-

mation

●

The high beam may not be auto-

matically turned off in the following 

situations:

• When oncoming vehicles sud-

denly appear from a curve

• When the vehicle is cut in front of 

by another vehicle

• When vehicles ahead are hidden 

from sight due to repeated curves, 

road dividers or roadside trees

• When vehicles ahead appear from 

the faraway lane on a wide road

• When vehicles ahead have no 

lights

●

The high beam may be turned off 

if a vehicle ahead that is using fog 

lights without using the headlights 

is detected.

●

House lights, street lights, traffic 

signals, and illuminated billboards 

or signs may cause the high beam 

to switch to the low beams, or the 

low beams to remain on.

●

The following factors may affect 

the amount of time taken to turn 

the high beam on or off:

• The brightness of headlights, fog 

lights, and tail lights of vehicles 

ahead

• The movement and direction of 

vehicles ahead

• When a vehicle ahead only has 

operational lights on one side

• When a vehicle ahead is a two-

wheeled vehicle

• The condition of the road (gradi-

ent, curve, condition of the road 

surface etc.)

• The number of passengers and 

amount of luggage

●

The high beam may be turned on 

or off when the driver does not 

expect it.

●

Bicycles or similar objects may not 

be detected.

●

In the situations shown below, the 

system may not be able to accu-

rately detect surrounding bright-

ness levels. This may cause the 

low beams to remain on or the 

high beams to cause problems for 

pedestrians, vehicles ahead or 

other parties. In these cases, 

manually switch between the high 

and low beams.

• In bad weather (rain, snow, fog, 

216

4-3. Operating the lights and wipers

sandstorms, etc.)

• The windshield is obscured by 

fog, mist, ice, dirt, etc.

• The windshield is cracked or dam-

aged

• The front camera is deformed or 

dirty

• When the temperature of the front 

camera is extremely high

• Surrounding brightness levels are 

equal to those of headlights, tail 

lights or fog lights

• When headlights or tail lights of 

vehicles ahead are turned off, 

dirty, changing color, or not aimed 

properly

• When the vehicle is hit by water, 

snow, dust, etc. from a preceding 

vehicle

• When driving through an area of 

intermittently changing brightness 

and darkness

• When frequently and repeatedly 

driving ascending/descending 

roads, or roads with rough, bumpy 

or uneven surfaces (such as 

stone-paved roads, gravel roads, 

etc.)

• When frequently and repeatedly 

taking curves or driving on a wind-

ing road

• There is a highly reflective object 

ahead of the vehicle, such as a 

sign or mirror

• The back of a vehicle ahead is 

highly reflective, such as a con-

tainer on a truck

• The vehicle’s headlights are dam-

aged or dirty, or are not aimed 

properly

• The vehicle is listing or titling due 

to a flat tire, a trailer being towed, 

etc.

• The high beam and low beam are 

repeatedly being switched 

between in an abnormal manner

• The driver believes that the high 

beam may be causing problems 

or distress to other drivers or 

pedestrians nearby

■

Temporarily lowering sensor 

sensitivity

The sensitivity of the sensor can be 

temporarily lowered.

1

Turn the power switch off while 

the following conditions are met.

●

The headlight switch is in 

 or 

.

●

The headlight switch lever is in 

low beam position.

●

Automatic High Beam switch is 

on.

2

Turn the power switch to ON.

3

Within 60 seconds after step 

2

, 

repeat pushing the headlight 

switch lever to the high beam 

position then pulling it to the orig-

inal position quickly 10 times, 

then leave the lever in the origi-

nal position.

4

If the sensitivity is changed, the 

AHB indicator is turn on and off 3 

times.

Automatic High Beam (headlights) 

may turn on even when the vehicle 

is stopped.

■

Switching to the high 
beams

Push the lever away from you.

The AHB indicator will turn off and 
the high beam indicator will turn on.
Pull the lever to its original position 
to activate the Automatic High 
Beam system.

Turning the high beams 
on/off manually

217

4-3. Operating the lights and wipers

4

Dr

iv

ing

■

Switching to the low beams

Press the Automatic High Beam 
switch.

The AHB indicator will turn off.
Press the switch to activate the 
Automatic High Beam system 
again.

■

Temporarily switching to 
the low beams

Pull the lever toward you and 
then return it to its original posi-
tion.
The high beams are on while 
the lever is pulled toward you. 
However, after the lever is 
returned to its original position, 
the low beams remain on for a 
certain period of time. After-
wards, the Automatic High 
Beam system will be activated 
again.

■

Temporarily switching to the 

low beams

It is recommended to switch to the 

low beams when the high beam 

may cause problems or distress to 

other drivers or pedestrians nearby.

218

4-3. Operating the lights and wipers

*

: If equipped

Press the switch.

■

Light bar operating condition

When the following conditions are 

met, the light bar will turn on:

●

The high beam headlights are on.

●

The light bar switch is pressed.

●

The power switch is in ON.

■

If the indicator blinks twice 

when the switch is pressed

Light bar will not turn on. Check that 

the high beam headlights are turned 

on.

■

If the indicator blinks slowly 

when the switch is pressed

Light bar will not turn on. Check that 

the power switch is in ON, or that 

the “READY” indicator is illumi-

nated.

Operate the 

 lever operates 

the wipers or washer as follows:



Intermittent windshield wip-
ers with interval adjuster

When intermittent windshield 
wiper operation is selected, the 
wiper interval can be also 
adjusted.

1

*1

 or 

*2

Light bar

*

Turning the light bar 
on/off

Windshield wipers and 

washer

Operating the lever can 
switch between automatic 
operation and manual oper-
ation, or can use the 
washer.

NOTICE

■

When the windshield is dry

Do not use the wipers, as they 

may damage the windshield.

Operating the wiper lever

219

4-3. Operating the lights and wipers

4

Dr

iv

ing

Off

2

*1

 or 

*2

Intermittent operation

3

*1

 or 

*2

Low speed wiper operation

4

*1

 or 

*2

High speed wiper operation

5

*1

 or 

*2

Temporary operation

Wiper intervals can be adjusted 
when intermittent operation is 
selected.

6

Increases the intermittent 
windshield wiper frequency

7

Decreases the intermittent 
windshield wiper frequency

8

 Washer/wiper dual oper-

ation

Pulling the lever operates the wip-

ers and washer.
(After operating several times, the 
wipers operate once more time 
after a short delay to prevent drip-
ping. However, the dripping preven-
tion does not operate while the 
vehicle is moving.)

*1

:U.S.A.

*2

:Canada



Rain-sensing windshield wip-
ers

When 

 is selected, the 

wipers will operate automatically 
when the sensor detects falling 
rain. The system automatically 
adjusts wiper timing in accor-
dance with rain volume and 
vehicle speed.

1

*1

 or 

*2

Off

2

 Rain-sensing wiper 

operation

The wipers will operate automati-
cally when the sensor detects fall-
ing rain. The system automatically 

220

4-3. Operating the lights and wipers

adjusts wiper timing in accordance 
with rain volume and vehicle speed.

3

*1

 or 

*2

Low speed wiper operation

4

*1

 or 

*2

High speed wiper operation

5

*1

 or 

*2

Temporary operation

When 

 is selected, the 

sensor sensitivity can be 
adjusted by turning the switch 
ring.

6

Increases the sensitivity

7

Decreases the sensitivity

8

 Washer/wiper dual oper-

ation

Pulling the lever operates the wip-
ers and washer.
(After operating several times, the 

wipers operate once more time 
after a short delay to prevent drip-
ping. However, the dripping preven-
tion does not operate while the 
vehicle is moving.)

*1

:U.S.A.

*2

:Canada

■

The windshield wiper and 

washer can be operated when

The power switch is in ON.

■

Effects of vehicle speed on 

wiper operation (vehicles with 

rain-sensing windshield wipers)

Even when the wipers are not in 

AUTO mode, vehicle speed affects 

the time until the drip prevention 

wiper sweep occurs.
With low speed windshield wiper 

operation selected, wiper operation 

will be switched from low speed to 

intermittent wiper operation only 

when the vehicle is stationary.

(However, when the sensor sensitiv-

ity is adjusted to the highest level, 

the mode cannot be switched.)

■

Raindrop sensor (vehicles with 

rain-sensing windshield wipers)

●

The raindrop sensor judges the 

amount of raindrops.

An optical sensor is adopted. It 

may not operate properly when 

sunlight from the rising or setting 

of the sun intermittently strikes the 

windshield, or if bugs, etc., are 

present on the windshield.

●

If the wiper is turned to AUTO 

221

4-3. Operating the lights and wipers

4

Dr

iv

ing

mode while the power switch is in 

ON, the wipers will operate once 

to show that AUTO mode is acti-

vated.

●

If the temperature of the raindrop 

sensor is 185°F (85°C) or higher, 

or 5°F (-15°C) or lower, automatic 

operation may not occur. In this 

case, operate the wipers in any 

mode other than AUTO mode.

■

If no windshield washer fluid 

sprays

Check that the washer nozzles are 

not blocked if there is washer fluid in 

the windshield washer fluid reser-

voir.

WARNING

■

Caution regarding the use of 

windshield wipers in AUTO 

mode (vehicles with rain-

sensing windshield wipers)

The windshield wipers may oper-

ate unexpectedly if the sensor is 

touched or the windshield is sub-

ject to vibration in AUTO mode. 

Take care that your fingers or any-

thing else do not become caught 

in the windshield wipers.

■

Caution regarding the use of 

washer fluid

When it is cold, do not use the 

washer fluid until the windshield 

becomes warm. The fluid may 

freeze on the windshield and 

cause low visibility. This may lead 

to an accident, resulting in death 

or serious injury.

NOTICE

■

When there is no washer fluid 

spray from the nozzle

Damage to the washer fluid pump 

may be caused if the lever is 

pulled toward you and held con-

tinually.

■

When a nozzle becomes 

blocked

In this case, contact your Toyota 

dealer.

Do not try to clear it with a pin or 

other object. The nozzle will be 

damaged.

■

To prevent 12-volt battery dis-

charge

Do not leave the wipers on longer 

than necessary when the hybrid 

system is off.

222

4-4. Refueling

4-4.Refueling



Turn the power switch off and 
ensure that all the doors and 
windows are closed.



Confirm the type of fuel.

■

Fuel types



P.542

■

Fuel tank opening for unleaded 

gasoline

To help prevent incorrect fueling, 

your vehicle has a fuel tank opening 

that only accommodates the spe-

cial nozzle on unleaded fuel pumps.

Opening the fuel tank 

cap

The fuel tank of your vehicle 
has a special structure, 
which requires a reduction 
in fuel tank pressure before 
refueling. After the opener 
switch has been pressed, it 
will take several seconds 
until the vehicle is ready for 
refueling.

Before refueling the vehi-
cle

WARNING

■

When refueling the vehicle

Observe the following precautions 

while refueling the vehicle. Failure 

to do so may result in death or 

serious injury.

●

After exiting the vehicle and 

before opening the fuel door, 

touch an unpainted metal sur-

face to discharge any static 

electricity. It is important to dis-

charge static electricity before 

refueling because sparks result-

ing from static electricity can 

cause fuel vapors to ignite while 

refueling.

●

Always hold the grips on the 

fuel tank cap and turn it slowly 

to remove it.

A whooshing sound may be 

heard when the fuel tank cap is 

loosened. Wait until the sound 

cannot be heard before fully 

removing the cap. In hot 

weather, pressurized fuel may 

spray out of the filler neck and 

cause injury.

●

Do not allow anyone that has 

not discharged static electricity 

from their body to come close to 

an open fuel tank.

●

Do not inhale vaporized fuel.

Fuel contains substances that 

are harmful if inhaled.

●

Do not smoke while refueling 

the vehicle.

Doing so may cause the fuel to 

ignite and cause a fire.

●

Do not return to the vehicle or 

touch any person or object that 

is statically charged. This may 

cause static electricity to build 

up, resulting in a possible igni-

tion hazard.

■

When refueling

Observe the following precautions 

to prevent fuel overflowing from 

the fuel tank:

●

Securely insert the fuel nozzle 

into the fuel filler neck.

●

Stop filling the tank after the fuel 

nozzle automatically clicks off.

223

4-4. Refueling

4

Dr

iv

ing

1

Press the opener switch.

2

Turn the fuel tank cap slowly 
to open it and put it into the 
holder on the fuel filler door.

After refueling, turn the fuel tank 
cap until you hear a click. Once 
the cap is released, it will turn 
slightly in the opposite direction.

WARNING

●

Do not top off the fuel tank.

NOTICE

■

Refueling

●

Finish refueling within 30 min-

utes. If more than 30 minutes 

passes, the internal valve 

closes. In this condition, fuel 

may overflow during the refuel-

ing process. Press the fuel filler 

door opener switch again.

●

Make sure that the fuel filler 

door lock is not pushed by the 

fuel nozzle boot, etc. If the lock 

is held, the internal valve closes 

and fuel may overflow. To pre-

vent it, press the fuel filler door 

opener switch again.

●

Do not spill fuel during refueling. 

Doing so may damage the vehi-

cle, such as causing the emis-

sion control system to operate 

abnormally or damaging fuel 

system components or the vehi-

cle’s painted surface.

Opening the fuel tank cap

Closing the fuel tank cap