Content .. 17 18 19 20 ..

Toyota bZ4X (2023 year). Manual in english - page 19

305

5-4. Using the driving support systems

ing

Approximately 9.8 ft. (3 m) from the rear bumper

Approximately 9.8 ft. (3 m) to 197 ft. (60 m) from the rear
bumper

:The area between the side of the vehicle and 1.6 ft. (0.5 m) from the side

of the vehicle cannot be detected.

:The greater the difference in speed between your vehicle and the

detected vehicle is, the farther away the vehicle will be detected, causing
the outside rear view mirror indicator to illuminate or flash.

■

The Blind Spot Monitor is oper-

ational when

The Blind Spot Monitor is opera-

tional when all of the following con-

ditions are met:

●

The power switch is in ON.

●

The Blind Spot Monitor is on.

●

The shift position is in a position

other than R.

●

The vehicle speed is greater than

approximately 7 mph (10 km/h).

■

The Blind Spot Monitor will

detect a vehicle when

The Blind Spot Monitor will detect a

vehicle present in the detection area

in the following situations:

●

A vehicle in an adjacent lane over-

takes your vehicle.

●

You overtake a vehicle in an adja-

cent lane slowly.

●

Another vehicle enters the detec-

tion area when it changes lanes.

■

Conditions under which the

system will not detect a vehicle

The Blind Spot Monitor is not

designed to detect the following

types of vehicles and/or objects:

●

Small motorcycles, bicycles,
pedestrians, etc.,

●

Vehicles traveling in the opposite

direction

●

Guardrails, walls, signs, parked

vehicles and similar stationary
objects

●

Following vehicles that are in the
same lane

●

Vehicles traveling 2 lanes away
from your vehicle

●

Vehicles which are being over-
taken rapidly by your vehicle

: Depending on the conditions,

detection of a vehicle and/or
object may occur.

■

Conditions under which the

system may not function cor-

rectly

●

The Blind Spot Monitor may not

detect vehicles correctly in the fol-

lowing situations:

• When the sensor is misaligned

due to a strong impact to the sen-

sor or its surrounding area

• When mud, snow, ice, a sticker,

etc., is covering the sensor or sur-

rounding area on the rear bumper

• When driving on a road surface

that is wet with standing water

during bad weather, such as

heavy rain, snow, or fog

• When multiple vehicles are

approaching with only a small gap

between each vehicle

• When the distance between your

vehicle and a following vehicle is

short

• When there is a significant differ-

ence in speed between your vehi-

cle and the vehicle that enters the

detection area

• When the difference in speed

between your vehicle and another

vehicle is changing

306

5-4. Using the driving support systems

• When a vehicle enters a detection

area traveling at about the same

speed as your vehicle

• As your vehicle starts from a stop,

a vehicle remains in the detection

area

• When driving up and down con-

secutive steep inclines, such as

hills, dips in the road, etc.

• When driving on roads with sharp

bends, consecutive curves, or

uneven surfaces

• When vehicle lanes are wide, or

when driving on the edge of a

lane, and the vehicle in an adja-

cent lane is far away from your

vehicle

• When an accessory (such as a

bicycle carrier) is installed to the

rear of the vehicle

• When there is a significant differ-

ence in height between your vehi-

cle and the vehicle that enters the

detection area

• Immediately after the Blind Spot

Monitor is turned on

• When towing with the vehicle

●

Instances of the Blind Spot Moni-

tor unnecessarily detecting a vehi-

cle and/or object may increase in

the following situations:

• When the sensor is misaligned

due to a strong impact to the sen-

sor or its surrounding area

• When the distance between your

vehicle and a guardrail, wall, etc.,

that enters the detection area is

short

• When driving up and down con-

secutive steep inclines, such as

hills, dips in the road, etc.

• When vehicle lanes are narrow, or

when driving on the edge of a

lane, and a vehicle traveling in a

lane other than the adjacent lanes

enters the detection area

• When driving on roads with sharp

bends, consecutive curves, or

uneven surfaces

• When the tires are slipping or

spinning

• When the distance between your

vehicle and a following vehicle is

short

• When an accessory (such as a

bicycle carrier) is installed to the

rear of the vehicle

• When towing with the vehicle

307

5-4. Using the driving support systems

ing

: If equipped

Multi-information display

Turning the Safe Exit Assist on/off
When the system determines that
the possibility of a collision with a
door is high, the target door is dis-
played on the multi-information dis-
play. Also, if the door is opened
when the outside rear view mirror
indicator is illuminated, a buzzer
will sound as a warning.

Outside rear view mirror indi-
cators

When a vehicle or bicycle which
may collide with a door (other than
the back door) when opened is
detected, the outside rear view mir-
ror indicator on the detected side
will illuminate. If the door on the
detected side is open, the outside
rear view mirror indicator will blink.

■

Outside rear view mirror indica-

tor visibility

In strong sunlight, the outside rear

view mirror indicator may be difficult

to see.

■

Buzzer

If the volume setting of the audio

system is high or the surrounding

area is loud, it may be difficult to

hear the buzzer.

SEA (Safe Exit Assist)

The Safe Exit Assist is a
system that uses radar sen-
sors installed on the inner
side of the rear bumper to
help occupants judge if an
approaching vehicle or
bicycle may collide with a
door to reduce the possibil-
ity of a collision.

WARNING

■

Cautions regarding the use of

the system

●

The driver is solely responsible

for safe driving. Always drive

safely, taking care to observe

your surroundings.

●

Safe Exit Assist is a supplemen-

tary system that, when the vehi-

cle is stopped, informs

occupants of the existence of

approaching vehicles and bicy-

cles. As this system alone can-

not be used to judge safety,

over-reliance on this system

may lead to an accident result-

ing in death or serious injury.

As the system may not function

correctly under certain condi-

tions, visual confirmation of

safety with the passengers’ own

eyes and mirrors is necessary.

System components

308

5-4. Using the driving support systems

■

Customization

Some functions can be customized.

(



P.574)

The Safe Exit Assist can be
enabled/disabled on

of the

multi-information display.
(



P.156)

When the Safe Exit Assist is off,
the driving assist information
indicator (



P.149) will illumi-

nate. At this time, “Safe Exit
Assist OFF” will be displayed on
the multi-information display.

WARNING

■

To ensure the system can

operate properly

Safe Exit Assist sensors are

installed behind the left and right

sides of the rear bumper respec-

tively. Observe the following to

ensure the Safe Exit Assist can

operate correctly.

●

Keep the sensors and the sur-

rounding areas on the rear

bumper clean at all times.

If a sensor or its surrounding

area on the rear bumper is dirty

or covered with snow, the Safe

Exit Assist may not operate and

a warning message will be dis-

played. In this situation, clear off

the dirt or snow and drive the

vehicle with the operation condi-

tions of the SEA function satis-

fied for approximately 10

minutes. If the warning mes-

sage does not disappear, have

the vehicle inspected by your

Toyota dealer.

●

Do not attach accessories,

stickers (including transparent

stickers), aluminum tape, etc.,

to a sensor or its surrounding

area on the rear bumper.

●

Do not subject a sensor or its

surrounding area on the rear

bumper to a strong impact.

If a sensor is moved even

slightly off position, the system

may malfunction and vehicles

may not be detected correctly.

In the following situations, have

the vehicle inspected by your

Toyota dealer.

• A sensor or its surrounding area

is subject to a strong impact.

• If the surrounding area of a sen-

sor is scratched or dented, or

part of them has become dis-

connected.

●

Do not disassemble the sensor.

●

Do not modify the sensor or sur-

rounding area on the rear

bumper.

●

If a sensor or the rear bumper

needs to be removed/installed

or replaced, contact your Toyota

dealer.

●

Do not paint the rear bumper

any color other than an official

Toyota color.

Turning the Safe Exit
Assist system on/off

309

5-4. Using the driving support systems

ing

Each time the power switch is
turned to ON, the Safe Exit

Assist is enabled.

When the Safe Exit Assist detects the following vehicles or bicycles
using a rear side radar sensor, the occupants of the vehicle are
informed through an outside rear view mirror indicator, buzzer, dis-
play on the meter, and voice notification.

A Vehicle or bicycle which has a high possibility of colliding with a
door (other than the back door) when opened

The areas that vehicles can be detected in are outlined below.

Approximately 145ft. (45m) rearward from the front door

: The faster the speed of the approaching vehicle or bicycle, the door mir-

ror indicator will turn on or flash, the farther the vehicle or bicycle is to the
door.

■

The Safe Exit Assist is opera-

tional when

The Safe Exit Assist is operational

when all of the following conditions

are met:

Objects that can be detected by the Safe Exit Assist

The Safe Exit Assist detection areas

310

5-4. Using the driving support systems

●

When the EV system is running,

less than 3 minutes have elapsed

since the EV system was stopped,

or less than 3 minutes have

elapsed since a door was opened

and someone has entered the

vehicle (the time which operation

is possible may be extended if a

door is opened and closed)

●

When the Safe Exit Assist is on

●

The vehicle is stopped.

●

The shift position is in a position

other than R.

■

The Safe Exit Assist will detect

a vehicle when

The Safe Exit Assist will detect a

vehicle present in the detection area

in the following situations:

When the vehicle is stopped and a

vehicle or bicycle, which is traveling

parallel to the vehicle, is approach-

ing within the area that a door opens

(other than the back door)

■

Conditions under which the

system will not detect a vehicle

●

Safe Exit Assist does not detect

the following objects, vehicles,

and bicycles:

• Vehicles or bicycles which are

approaching slowly

• Vehicles or bicycles which are

determined to have a low possibil-

ity of colliding with a door (other

than the back door) when opened

• Vehicles or bicycles which are

determined to have a low possibil-

ity of colliding with a door when

opened

• Vehicles or bicycles which are

approaching from directly behind

• Vehicles or bicycles which are

approaching from the front

• Guardrails, walls, signs, parked

vehicles, and other stationary

objects

• Animals, etc.

●

In situations such as the following,

Safe Exit Assist will not operate:

• When 3 minutes or more have

elapsed since the EV system off

(the time which operation is possi-

ble may be extended if a door is

opened and closed)

• When your vehicle is not com-

pletely stopped

■

Conditions under which the

system may not function cor-

rectly

●

Vehicles and bicycles may not be

effectively detected in the follow-

ing situations:

• When the sensor is misaligned

due to a strong impact to the sen-

sor or its surrounding area

• When mud, snow, ice, a sticker,

etc., is covering the sensor or sur-

rounding area on the rear bumper

• When driving on a road surface

that is wet with standing water

during bad weather, such as

heavy rain, snow, or fog

• When a vehicle or bicycle

approaches from behind a nearby

parked vehicle

• When an approaching vehicle or

bicycle suddenly changes direc-

tion

• Immediately after a vehicle or

bicycle starts moving

• When the back door is open

• When a bicycle carrier, ramp, or

other accessory is installed to the

back of the vehicle

• When a parked vehicle, wall, sign,

person or other stationary object

is behind the vehicle

• When the vehicle is stopped at an

angle to the road

• When a vehicle is traveling near

an approaching vehicle or bicycle

• When an approaching vehicle or

bicycle is traveling along a station-

ary object, such a wall or sign

• When a vehicle or bicycle is

approaching at high speed

• When towing with the vehicle

• When stopped on a steep incline

• When stopped on a curve or at the

exit of a curve

●

Instances of the Safe Exit Assist

unnecessarily detecting a vehicle

and/or object may increase in the

following situations:

• When the sensor is misaligned

311

5-4. Using the driving support systems

ing

due to a strong impact to the sen-

sor or its surrounding area

• When a vehicle or bicycle

approaches from behind your

vehicle at an angle

• When the vehicle is stopped at an

angle to the road

• When a vehicle or bicycle

approaches from behind a parked

vehicle at an angle

• When a parked vehicle, wall, sign,

person or other stationary object

is behind the vehicle

• When an approaching vehicle or

bicycle suddenly changes direc-

tion

• When an approaching vehicle or

bicycle is traveling along a station-

ary object, such a wall or sign

• When the back door is open

• When a bicycle carrier, ramp, or

other accessory is installed to the

back of the vehicle

• When a vehicle or bicycle is

approaching at high speed

• When towing with the vehicle

• When stopped on a steep incline

• When stopped on a curve or at the

exit of a curve

: If equipped

■

Types of sensors

Front corner sensors

Front center sensors

Rear corner sensors

Rear center sensors

Front side sensors (vehicles
with Advanced Park)

Rear side sensors (vehicles
with Advanced Park)

Intuitive parking

assist

The distance from your
vehicle to objects, such as a
wall, when parallel parking
or maneuvering into a
garage is measured by the
sensors and communi-
cated via the multimedia
display and a buzzer.
Always check the surround-
ing area when using this
system.

System components

312

5-4. Using the driving support systems

■

Display

When the sensors detect an
object, such as a wall, a graphic
is shown on the multimedia dis-
play depending on the position
and distance to the object. (As
the distance to the object
becomes short, the distance
segments may blink.)



Multimedia display (vehicles
without Advanced Park)



Multimedia display (vehicles
with Advanced Park)

Front corner sensor detection

Front center sensor detection

Rear corner sensor detection

Rear center sensor detection

Front side sensor detection

Rear side sensor detection

Use the meter control switches
to enable/disable the intuitive
parking assist. (



P.156)

Press

to select

Press

to select

and then press

When the intuitive parking assist

function is disabled, the intuitive

parking assist OFF indicator

(



P.149) illuminates.

To re-enable the system when it
was disabled, select

on the

multi-information display, select

and then On. If disabled using

this method, the system will not be
re-enabled by turning the power
switch off and then to ON.

Turning intuitive parking
assist on/off

WARNING

■

Cautions regarding the use of

the system

There is a limit to the degree of

recognition accuracy and control

performance that this system can

provide, do not overly rely on this

system. The driver is always

responsible for paying attention to

the vehicle’s surroundings and

driving safely.

■

To ensure the system can

operate properly

Observe the following precau-

tions.
Failing to do so may result in the

vehicle being unable to be driven

safely and possibly cause an acci-

dent.

313

5-4. Using the driving support systems

ing

■

The system can be operated

when

●

The power switch is in ON.

●

Intuitive parking assist function is

on.

●

The vehicle speed is less than

about 6 mph (10 km/h).

●

A shift position other than P is

selected.

■

Sensor detection information

●

The sensor’s detection areas are

limited to the areas around the

vehicle’s front and rear bumpers.

●

The following situations may occur

during use.

• Depending on the shape of the

object and other factors, the

detection distance may shorten, or

detection may be impossible.

• Detection may be impossible if

static objects draw too close to the

sensor.

• There will be a short delay

between static object detection

and display (warning buzzer

sounds). Even at low speeds,

there is a possibility that the object

will come within 11.9 in. (30 cm)

before the display is shown and

the warning buzzer sounds.

• It might be difficult to hear the

buzzer due to the volume of the

audio system or air flow noise of

the air conditioning system.

• It may be difficult to hear the

sound of this system due to the

buzzers of other systems.

WARNING

●

Do not damage the sensors,

and always keep them clean.

●

Do not attach a sticker or install

an electronic component, such

as a backlit license plate (espe-

cially fluorescent type), fog

lights, fender pole or wireless

antenna near a radar sensor.

●

Do not subject the surrounding

area of the sensor to a strong

impact. If subjected to an

impact, have the vehicle

inspected by your Toyota

dealer. If the front or rear

bumper needs to be

removed/installed or replaced,

contact your Toyota dealer.

●

Do not modify, disassemble or

paint the sensors.

●

Do not attach a license plate

cover.

●

Keep your tires properly

inflated.

■

When to disable the function

In the following situations, disable

the function as it may operate

even though there is no possibility

of a collision.

●

Failing to observe the warnings

above.

●

A non-genuine Toyota suspen-

sion (lowered suspension, etc.)

is installed.

■

Notes when washing the vehi-

cle

Do not apply intensive bursts of

water or steam to the sensor

area.
Doing so may result in the sensor

malfunctioning.

●

When using a high pressure

washer to wash the vehicle, do

not spray the sensors directly,

as doing so may cause a sensor

to malfunction.

●

When using steam to clean the

vehicle, do not direct steam too

close to the sensors as doing so

may cause a sensor to malfunc-

tion.

314

5-4. Using the driving support systems

■

Objects which the system may

not be properly detected

The shape of the object may pre-

vent the sensor from detecting it.

Pay particular attention to the follow-

ing objects:

●

Wires, fences, ropes, etc.

●

Cotton, snow and other materials

that absorb sound waves

●

Sharply-angled objects

●

Low objects

●

Tall objects with upper sections

projecting outwards in the direc-

tion of your vehicle

People may not be detected if they

are wearing certain types of cloth-

ing.

■

Situations in which the system

may not operate properly

Certain vehicle conditions and the

surrounding environment may affect

the ability of a sensor to correctly

detect objects. Particular instances

where this may occur are listed

below.

●

There is dirt, snow, water drops or

ice on a sensor. (Cleaning the

sensors will resolve this problem.)

●

A sensor is frozen. (Thawing the

area will resolve this problem.)

In especially cold weather, if a

sensor is frozen the sensor dis-

play may be displayed abnormally,

or objects, such as a wall, may not

be detected.

●

When a sensor or the area around

a sensor is extremely hot or cold.

●

On an extremely bumpy road, on

an incline, on gravel, or on grass.

●

When vehicle horns, vehicle

detectors, motorcycle engines, air

brakes of large vehicles, the clear-

ance sonar of other vehicles or

other devices which produce ultra-

sonic waves are near the vehicle

●

A sensor is coated with a sheet of

spray or heavy rain.

●

If objects draw too close to the

sensor.

●

When a pedestrian is wearing

clothing that does not reflect ultra-

sonic waves (ex. skirts with gath-

ers or frills).

●

When objects that are not perpen-

dicular to the ground, not perpen-

dicular to the vehicle traveling

direction, uneven, or waving are in

the detection range.

●

Strong wind is blowing

●

When driving in inclement weather

such as fog, snow or a sandstorm

●

When an object that cannot be

detected is between the vehicle

and a detected object

●

If an object such as a vehicle,

motorcycle, bicycle or pedestrian

cuts in front of the vehicle or runs

out from the side of the vehicle

●

If the orientation of a sensor has

been changed due to a collision or

other impact

●

When equipment that may

obstruct a sensor is installed, such

as a towing eyelet, bumper pro-

tector (an additional trim strip,

etc.), bicycle carrier, or snow plow

●

If the front of the vehicle is raised

or lowered due to the carried load

●

If the vehicle cannot be driven in a

stable manner, such as when the

vehicle has been in an accident or

is malfunctioning

●

When a tire chains, compact

spare tire or an emergency tire

puncture repair kit is used

315

5-4. Using the driving support systems

ing

■

Situations in which the system

may operate even if there is no

possibility of a collision

In some situations, such as the fol-

lowing, the system may operate

even though there is no possibility of

a collision.

●

When driving on a narrow road

●

When driving toward a banner,

flag, low-hanging branch or boom

barrier (such as those used at rail-

road crossings, toll gates and

parking lots)

●

When there is a rut or hole in the

surface of the road

●

When driving on a metal cover

(grating), such as those used for

drainage ditches

●

When driving up or down a steep

slope

●

If a sensor is hit by a large amount

of water, such as when driving on

a flooded road

●

There is dirt, snow, water drops or

ice on a sensor. (Cleaning the

sensors will resolve this problem.)

●

A sensor is coated with a sheet of

spray or heavy rain

●

When driving in inclement weather

such as fog, snow or a sandstorm

●

When strong winds are blowing

●

When vehicle horns, vehicle

detectors, motorcycle engines, air

brakes of large vehicles, the clear-

ance sonar of other vehicles or

other devices which produce ultra-

sonic waves are near the vehicle

●

If the front of the vehicle is raised

or lowered due to the carried load

●

If the orientation of a sensor has

been changed due to a collision or

other impact

●

The vehicle is approaching a tall

or curved curb

●

Driving close to columns (H-

shaped steel beams, etc.) in multi-

story parking garages, construc-

tion sites, etc.

●

If the vehicle cannot be driven in a

stable manner, such as when the

vehicle has been in an accident or

is malfunctioning

●

On an extremely bumpy road, on

an incline, on gravel, or on grass

●

When a tire chains, compact

spare tire or an emergency tire

puncture repair kit is used

316

5-4. Using the driving support systems

■

Detection range of the sen-
sors (vehicles without
Advanced Park)

Approximately 3.3 ft. (100
cm)

Approximately 4.9 ft. (150
cm)

Approximately 2.0 ft. (60 cm)

The diagram shows the detection
range of the sensors. Note that the
sensors cannot detect objects that
are extremely close to the vehicle.
The range of the sensors may
change depending on the shape of
the object, etc.,

■

Detection range of the sen-
sors (vehicles with
Advanced Park)

Approximately 6.6 ft. (200
cm)

Sensor detection display,
object distance

317

5-4. Using the driving support systems

ing

■

The distance and buzzer



Vehicles without Advanced Park

: Automatic buzzer mute function is enabled. (



P.319)

Approximate distance to obstacle

Buzzer

Front sensor:
Approximately 3.3 ft. to 2.0 ft. (100
cm to 60 cm)

Rear sensor:
Approximately 4.9 ft. to 2.0 ft. (150
cm to 60 cm)

Slow

Approximately 2.0 ft. to 1.5 ft. (60 cm
to 45 cm)

Medium

Approximately 1.5 ft. to 1.0 ft. (45 cm
to 30 cm)

Fast

Approximately 1.0 ft. to 0.5 ft. (30 cm
to 15 cm)

Continuous

Less than approximately 0.5 ft. (15
cm)

318

5-4. Using the driving support systems



Vehicles with Advanced Park

Approximate distance to obstacle

Buzzer

Front center sensor:
Approximately 6.6 ft. to 3.3 ft. (200
cm to100 cm)
Rear center sensor:
Approximately 6.6 ft. to 4.9 ft. (200
cm to 150 cm)
Side sensor:
Approximately 6.6 ft. to 5.4 ft. (200
cm to 165 cm)
Corner sensor:
Approximately 6.6 ft. to 2.0 ft. (200
cm to 60 cm)

Does not sound (Display only)

Front center sensor:
Approximately 3.3 ft. to 2.0 ft. (100
cm to 60cm)

Rear center sensor:
Approximately 4.9 ft. to 2.0 ft. (150
cm to 60cm)

Side sensor:
Approximately 5.4 ft. to 2.0 ft. (165
cm to 60 cm)

Slow

Side sensor:
Approximately 2.0 ft. to 1.3 ft. (60 cm
to 40 cm)

Other than side sensor:
Approximately 2.0 ft. to 1.5 ft. (60 cm
to 45cm)

Medium

319

5-4. Using the driving support systems

ing

: Automatic buzzer mute function is enabled. (



P.319)

■

Buzzer operation and dis-
tance to an object

A buzzer sounds when the sen-
sors are operating.



The buzzer beeps faster as
the vehicle approaches an
object.
When the vehicle comes
within approximately 1.0 ft.
(30 cm) of the object, the
buzzer sounds continuously.



When 2 or more sensors
simultaneously detect a static
object, the buzzer sounds for
the nearest object.



Even when the sensors are
operating, the buzzer will be
muted in some situations.
(automatic buzzer mute func-
tion)

■

Adjusting the buzzer vol-
ume

The buzzer volume can be
adjusted on the multi-informa-

tion display.
Use the meter control switches
to change settings. (



P.156)

Press

of the meter

control switch to select

Press

of the meter

control switch to select

and then press and hold

Select the volume and then
press

Each time the switch is pressed,

the volume level will change

between 1, 2, and 3.

■

Muting a buzzer temporarily

When an object is detected, the
temporary mute switch is dis-
played on the multimedia dis-
play system.
Select

to mute a buzzer of

the intuitive parking assist-sen-

Side sensor:
Approximately 1.3 ft. to 1.0 ft. (40 cm
to 30 cm)

Other than side sensor:
Approximately 1.5 ft. to 1.0 ft. (45cm
to 30 cm)

Fast

Less than approximately 1.0 ft. (30
cm)

Continuous

Less than approximately 0.5 ft. (15
cm)

Approximate distance to obstacle

Buzzer

320

5-4. Using the driving support systems

sor, RCTA, and RCD all
together.
Mute will be canceled automati-
cally in the following situations:



When the shift position is
changed.



When the vehicle speed
exceeds a certain speed.



When there is a malfunction
in a sensor or the system is
temporarily unavailable.



When the operating function
is disabled manually.



When the power switch is
turned off.

The object warning function
informs the driver of the exis-
tence of objects along the side
of the vehicle, using a display
and buzzer, if the objects are
within the estimated path of the
vehicle.

Object

Calculated vehicle route

When the vehicle is moving, the side sensors or side cameras can
detect objects. While the vehicle is moving, if a detected object can
no longer be detected by the side sensors or side cameras, the loca-
tion of the object relative to the vehicle is estimated. If the object is
determined to be in the estimated path of the vehicle, the object
warning function will operate.

Object detected by side sensors or side cameras

The vehicle is stopped and objects along the sides of the vehicle

Object warning function
(vehicles with Advanced
Park)

Content .. 17 18 19 20 ..