Toyota Proace EV (2022 year). Manual in english - page 2
21
Malfunction of the SCR emissions
While driving, the message is displayed every 30
Power indicator (Electric)
control system
seconds. The alert is repeated when switching
on the ignition.
Malfunction detection
You can continue driving for up to 1,100 km (685
miles) before the engine immobiliser system is
If a malfunction is detected,
triggered.
these warning lamps come on,
1
accompanied by an audible
WARNING
signal and an "Emissions fault”
or “NO START IN” message.
Have the system checked by any authorized
Toyota retailer or Toyota authorized repairer,
or any reliable repairer as soon as possible.
The alert is triggered while driving, when the
fault is detected for the first time, and thereafter
Starting prevented
when switching on the ignition for subsequent
journeys, while the cause of the fault persists.
Whenever the ignition is switched on, the
CHARGE
"Emissions fault: Starting prevented" or "NO
Traction battery charging during deceleration
NOTICE
START IN" message is displayed.
and braking.
ECO
If the fault is temporary, the alert disappears
WARNING
Moderate energy consumption and optimised
during the next journey, after self-diagnostic
driving range.
To be able to restart the engine, contact any
checks of the SCR emissions control system.
POWER
authorized Toyota retailer or Toyota
Energy consumption by the drive train during
Malfunction confirmed during the
authorized repairer, or any reliable repairer.
acceleration.
permitted driving phase (between 1,100
NEUTRAL
km and 0 km (685 miles and 0 miles))
On switching on the ignition, your vehicle’s
If the fault indication is still displayed
electric drive train neither consumes nor
permanently after 50 km (31 miles) of driving, the
generates energy: after sweeping over the
fault in the SCR system is confirmed.
indicator, the needle returns to its "neutral"
The AdBlue warning lamp flashes, and an
position.
"Emissions fault: Starting prevented in X
miles" or "NO START IN X miles" message is
displayed, indicating the driving range in miles or
kilometres.
22
Associated warning lamps
Thermal comfort
NOTICE
Two successive alert levels indicate that the
consumption indicator
With the ignition off, opening the driver's door
energy available has dropped to a low level:
activates the indicator, which moves to the
1st level: Reserve
(Electric)
100
"neutral" position.
The state of charge of the traction battery
0 %
is low.
Fixed LED and needle in the red zone,
Charge level indicator
accompanied by an audible signal.
(Electric)
► View the remaining range on the instrument
panel.
► Put the vehicle on charge as soon as
possible.
2nd level: Critical
The state of charge of the traction battery
is critical.
Fixed, together with the reserve LED,
accompanied by an audible signal.
The gauge shows the consumption of the
► You must put the vehicle on charge.
traction battery's electrical energy by the thermal
comfort devices in the passenger compartment.
WARNING
The devices in question are the heating and air
conditioning systems.
The remaining range is no longer calculated.
This equipment can be used:
The traction battery's actual charge level and
The drive train power gradually decreases.
- If the vehicle is not plugged in, when the
the remaining range are displayed continuously
The heating and air conditioning are switched
READY lamp is lit.
when the vehicle is started.
off (even if the needle indicating their
- If the vehicle is plugged in, when the ignition is
consumption is not at the "ECO" position).
switched on ("Lounge" mode).
NOTICE
Selecting ECO mode limits the performance
With the ignition off, opening the driver's door
of some of this equipment. The needle on the
activates the indicator.
thermal comfort consumption indicator then
moves into the "ECO" zone.
23
Total distance recorder
NOTICE
To quickly heat or cool the passenger
compartment, feel free to temporarily select
the maximum heating or cooling setting.
► With the ignition on, press the button until
When the heating is on maximum, the gauge
zeros appear.
1
on the thermal comfort consumption indicator
is in the MAX zone. When the air conditioning
is on maximum, it stays in the ECO zone.
Lighting dimmer
Excessive use of thermal comfort equipment,
This system allows the brightness of the
particularly at low speed, can significantly
instruments and controls to be adjusted to suit
decrease the vehicle's range.
This recorder measures the total distance
the ambient light level.
Remember to optimise equipment settings
travelled by the vehicle since its initial
upon achieving the desired level of comfort,
registration.
and adjust them if necessary whenever you
Trip distance recorder (Diesel)
start the vehicle.
After an extended period without using the
heating, you may notice a slight odour during
the first few minutes of use.
Distance recorders
With the lamps on, press button A to increase
The total and trip distances are displayed for
the brightness of the lighting, or button B to
thirty seconds when the ignition is switched off,
decrease it.
when the driver's door is opened and when the
Release the button when the desired brightness
vehicle is locked or unlocked.
is reached.
This recorder measures the distance travelled
since it was last reset by the driver.
Resetting the trip recorder
24
With touch screen
Trip computer
On the instrument panel
Information displayed about the current journey
(range, fuel consumption, average speed, etc.).
Information display
To display the various trip computer tabs in turn:
► Press this button.
The following current information is shown in
► In the Settings menu, select "Brightness"
turn:
or "OPTIONS", "Screen configuration" then
- Driving range (Diesel).
"Brightness".
- Current consumption.
► Adjust the brightness by pressing the arrows
- Stop & Start time counter (Diesel).
or moving the slider.
► Press the button located on the end of the
- Trip "1" followed by (depending on version)
wiper control stalk.
trip "2" including average speed, average
NOTICE
With steering-mounted controls
consumption and distance travelled for each trip.
Trips "1" and "2" are independent but their use
The brightness can be set differently for day
is identical.
mode and night mode.
For example, trip "1" can be used for daily
figures and trip "2" for monthly figures.
► Press the knob on the steering wheel.
25
Trip reset
Definitions
Current consumption
The reset is performed when the trip counter is
(mpg or l/100 km or km/l)
displayed.
Range
(miles/kWh or kWh/100 km or km/kWh) (Electric)
(km or miles)
/
Calculated during the last few
Distance that can still be travelled with the
seconds.
fuel remaining in the tank (based on the
This function is only displayed at speeds above
1
average fuel consumption over the last few miles
19 mph (30 km/h) (Diesel).
(kilometres) travelled).
Average consumption
NOTICE
(mpg or l/100 km or km/l)
(miles/kWh or kWh/100 km or km/kWh) (Electric)
This value may vary following a change in the
/
Calculated since the last trip
driving style or terrain, resulting in a
computer reset.
► Press the button on the end of the wiper
significant change in the spot fuel
control lever for more than two seconds.
consumption.
Average speed
(km/h or mph)
When the range falls below 30 km (19 miles),
Calculated since the last trip computer
dashes are displayed.
reset.
After filling with at least 5 litres of fuel, the range
is recalculated and is displayed if it exceeds
Distance travelled
► Press the thumbwheel on the steering wheel
100 km (62 miles).
(km or miles)
for more than two seconds.
Calculated since the last trip computer
WARNING
reset.
If dashes instead of figures continue to be
Stop & Start time counter
displayed when driving, contact any
(minutes/seconds or hours/minutes)
authorized Toyota retailer or Toyota
authorized repairer, or any reliable repairer.
If your vehicle is fitted with Stop & Start, a time
counter calculates the time spent in STOP mode
during a journey.
► Press this button for more than 2 seconds.
It resets to zero every time the ignition is
switched on.
26
Touch screen
Recommendations
Menus
This screen is of the capacitive type.
This system gives access to the following
- Do not use pointed objects on the touch
elements:
screen.
- Permanent display of the time and outside
- Do not touch the touch screen with wet hands.
temperature (a blue warning lamp appears if
- Use a soft, clean cloth to clean the touch
there is a risk of ice).
screen.
- Vehicle functions and equipment setting
menus.
Principles
- Audio system and telephone controls and
NOTICE
display of related information.
► Use the buttons on each side of the touch
- Display of visual manoeuvring aid functions
screen to access the menus, then press the
Press the touch screen with three fingers to
- Internet services and display of related
buttons that appear on the touch screen.
show all of the menu buttons.
information.
Some menus may display across two pages:
- Navigation system controls and
press the "OPTIONS" button to access the
NOTICE
display of related information (depending on
second page.
version).
For more information about the menus, refer
NOTICE
to the sections describing the audio and
WARNING
After a few moments with no action on the
telematics systems.
For safety reasons, always stop the
second page, the first page is displayed
Radio/Media
vehicle before performing operations that
automatically.
require sustained attention.
To deactivate/activate a function, select "OFF"
Navigation (Depending on equipment)
Some functions are not accessible while
or "ON".
driving.
Configuring a function
Driving or Vehicle (Depending on
equipment)
Access to additional information on the
Activation, deactivation and settings for certain
function
functions.
Confirm
The functions are organised in 2 tabs: "Driving
functions" and "Vehicle settings".
Return to the previous page or confirm
Telephone
Applications
27
Display of available connected services.
Energy menu
Energy
Depending on version, this is accessible either:
Access the specific Electric functions
- directly, by pressing the button near the
(energy flow, consumption statistics, deferred
touch screen.
charge) organised in the corresponding 3 tabs.
- via the Applications menu.
or
- Blue bar chart: directly consumed energy
1
Settings
supplied by the traction battery.
Main settings for the audio system and
Flow
- Green bar chart: energy recovered during
touch screen.
The page displays a real-time representation of
deceleration and braking, used to recharge the
Audio system on/off.
the electric drive train’s operation.
battery.
Volume adjustment/mute.
The average result for the current trip is stated in
kWh/100 km.
Upper bar
► You can change the displayed time scale by
Certain information is displayed permanently in
pressing the - or + buttons.
the upper bar of the touch screen:
- Time and outside temperature (a blue warning
NOTICE
lamp appears if there is a risk of ice).
- Reminder of information from the
A current trip is any trip of more than 20
Radio Media and Telephone menus and
minutes without switching off the ignition.
navigation instructions (depending on
1. Active driving mode
equipment).
2. Electric motor
Charging
- Notifications.
3. Estimated traction battery charge level
- Access to the Settings.
4. Energy flows
This page allows you to programme deferred
charging.
The energy flows have a specific colour for each
For more information on Charging the traction
type of driving:
battery (Electric), refer to the corresponding
A. Blue: energy consumption
section.
B. Green: energy recovery
Statistics
This page shows electrical energy consumption
statistics.
28
Remotely-operable
NOTICE
Setting the date and time
functions (Electric)
Network coverage
Without Bluetooth® audio
(Available soon)
In order to be able to use the various remotely
system
operable features, ensure that your vehicle
is located in an area covered by the mobile
In addition to all the functions of the MyToyota
network.
application that you can access from a
A lack of network coverage may prevent
smartphone, you can access the following
communication with the vehicle (for example,
functions:
if it is in an underground car park). In such
- Battery charge management (Deferred
cases, the application will display a message
charging).
indicating that the connection with the vehicle
- Temperature pre-conditioning management.
could not be established.
- Consultation of the state of charge and range
of the vehicle.
Installation procedure
► Download the MyToyota app from the
appropriate online store for your smartphone.
Set the date and time via the instrument panel
► Create an account.
display.
► Enter the vehicle’s V.I.N. (code beginning
► Press and hold this button.
with "VF" on the vehicle registration document).
For more information on Identification
► Press one of these buttons to select
markings, refer to the corresponding section.
the setting to be changed.
► Briefly press this button to confirm.
► Press one of these buttons to change
the setting and confirm again to record
the change.
29
With Bluetooth® audio
With TOYOTA Pro Touch
system
with navigation system
► Press the MENU button for access to the
Time and date settings are only available if GPS
main menu.
synchronisation is deactivated.
► Press the "7" or "8" button to select the
► Select the Settings menu in the
"Personalisation-configuration" menu, then
banner of the touch screen.
1
confirm by pressing the OK button.
► Press the "OPTIONS" button to access the
► Press the "5" or "6" button to select the
secondary page.
Display configuration menu, then confirm by
► Select "Setting the time-date".
pressing the OKbutton.
► Press the "5" or "6" and "7" or "8" buttons to
► Select the "Date:" or "Time" tab.
adjust the date and time values, then confirm by
► Set the date and/or time using the numeric
pressing the OK button.
keypad.
► Confirm with "OK".
With TOYOTA Pro Touch
Additional settings
► Select the Settings menu in the upper
You can choose:
banner of the touch screen.
- To change the time zone.
► Select "Configuration".
- To change the display format of the date and
► Select "Date and time".
time (12h/24h).
- To activate or deactivate the summer time
► Select "Date" or "Time".
management function (+1 hour).
► Choose the display formats.
- To activate or deactivate GPS synchronisation
► Change the date and/or time using the
(UTC).
numeric keypad.
► Confirm with "OK".
NOTICE
The system does not automatically change
between winter and summer time (depending
on the country of sale).
30
Electronic key with
WARNING
NOTICE
remote control function
As a safety measure, never leave the vehicle,
The remote control buttons are not active with
and built-in key,
even for a short time, without taking the Smart
the ignition switched on.
Entry & Start system’s electronic key with
you.
NOTICE
Unfolding / Folding the key
Be aware of the risk of theft of the vehicle if
If one of the doors or the boot is still open or if
the key is present in one of the defined areas
the electronic key for the Smart Entry & Start
while the vehicle is unlocked.
system has been left inside the vehicle,
If a door is not properly closed (except the
central locking will not take place.
right-hand door with side-hinged rear
However, if the vehicle is fitted with an alarm,
doors):
it will be activated after 45 seconds.
- when the vehicle is stationary and engine
running, this warning lamp comes on,
NOTICE
accompanied by a warning message for a few
seconds,
► Press this button to unfold or fold the key.
If the vehicle is unlocked but the doors or boot
- when the vehicle is moving (at speeds above
are not subsequently opened, the vehicle will
6 mph (10 km/h)), this warning lamp comes on,
WARNING
automatically lock itself again after about
accompanied by an audible signal and a warning
30 seconds. If the vehicle is fitted with an
message for a few seconds.
The remote control may be damaged if you
alarm, it will be reactivated automatically.
do not press the button.
Remote control key
This allows the central locking or unlocking of the
Smart Entry & Start
NOTICE
vehicle using the door lock or remotely.
This allows the remote central locking or
It also allows the vehicle to be located, the fuel
Automatic door mirror folding and unfolding
unlocking of the vehicle.
filler cap to be removed and refitted and the
can be deactivated by any authorized Toyota
It is also used to locate and start the vehicle, as
engine to be started or switched off, as well as
retailer or Toyota authorized repairer, or any
well as providing protection against theft.
providing protection against theft.
reliable repairer.
31
Integral key
"Smart Entry & Start" on your person
Locating the vehicle
This is used to lock and unlock the vehicle when
Helps you to locate your vehicle from a distance,
the remote control cannot operate:
with the vehicle locked:
- remote control battery discharged, vehicle
- The direction indicators flash for approximately
battery discharged or disconnected, etc.
10 seconds.
– vehicle located in an area subject to strong
- The courtesy lamps come on.
2
electromagnetic interference.
► Press this button.
Remote operation of lighting
If fitted to the vehicle.
A short press on this button switches on
It allows the unlocking, locking and starting of the
the lighting remotely (lighting of
vehicle, while carrying the remote control on your
sidelamps, dipped beam headlamps and number
► Keep this button 1 pulled across to remove
person in the recognition zone "A".
plate lamps).
the key 2 from the device.
A second press on the button before the end of
NOTICE
the timed period cancels the remote lighting.
NOTICE
In the ignition on (accessories) position, with
Advice
If the alarm is activated, the audible signal
the "START/STOP" button, the hands-free
triggered on opening a door with the key
function is deactivated and it is impossible to
(integral with the remote control) will stop
WARNING
open the doors.
when the ignition is switched on.
For more information on Starting/switching
Remote control
off the engine, Smart Entry & Start and in
The remote control is a sensitive, high-
WARNING
particular the "ignition on" position, refer to
frequency device; avoid handling it in your
the corresponding section.
pocket, due to the risk of unintentionally
Once the built-in key is ejected, always keep
unlocking the vehicle.
it with you to be able to carry out the
Avoid pressing the remote control buttons
corresponding back-up precedures.
while out of range of the vehicle, due to
the risk of rendering the remote control
32
inoperative. It would then be necessary to
NOTICE
NOTICE
reset it.
The remote control does not work when the
Purchasing a second-hand vehicle
Electrical interference
key is in the ignition switch, even when the
Have the key codes memorised by any
The electronic key may not operate if close to
ignition is switched off.
authorized Toyota retailer or Toyota
certain electronic devices such as telephones
authorized repairer, or any reliable repairer, to
(switched on or on standby) or laptop
ensure that the keys in your possession are
computers, strong magnetic fields, etc. If this
WARNING
the only ones able to start the vehicle.
happens, remove the electronic key from the
Anti-theft protection
electronic device.
Do not modify the electronic vehicle
WARNING
immobiliser, as this might result in
WARNING
malfunctions.
To preserve the battery charge in the
For vehicles with a key ignition switch,
electronic key and the vehicle's battery, the
Accumulations (water, dust, grime, salt, etc.)
remember to remove the key and turn the
"hands-free" functions are set to hibernation
on the inner surface of the door handle may
steering wheel to engage the steering lock.
mode after 21 days without use. To restore
affect detection.
these functions, press one of the remote
If cleaning the inner surface of the door
WARNING
control buttons or start the engine with the
handle using a cloth does not restore
electronic key in the reader.
detection, contact any authorized Toyota
Locking the vehicle
For more information on starting with the
retailer or Toyota authorized repairer, or any
Driving with the doors locked could make
Smart Entry & Start system, refer to the
reliable repairer.
it more difficult for the emergency services
corresponding section.
A sudden splash of water (stream of water,
to enter the passenger compartment in an
high pressure jet washer, etc.) may be
emergency.
identified by the system as the desire to open
As a safety precaution, remove the key from
the vehicle.
the ignition or take the electronic key with you
when leaving the vehicle, even for a short
time.
33
Unlocking/Complete or
Unlocking/Complete
NOTICE
selective unlocking
unlocking
The separation of the cabin and loading
area unlocking is a security measure.
NOTICE
What is the purpose of total
It is used to lock out access to the part of the
or selective unlocking?
vehicle in which you are not present.
2
Unlocking is signalled by rapid flashing of the
direction indicators for a few seconds.
Activation/Deactivation
Depending on version, the door mirrors unfold
and the alarm is deactivated.
With the key
► To unlock the vehicle fully, turn the key in the
front left-hand door lock towards the front of the
vehicle.
If the vehicle has an alarm, it will not be
Complete unlocking unlocks all the vehicle’s
deactivated. Opening a door will trigger the
doors (front, side and rear).
► To activateselective unlocking
alarm, which can be stopped by switching the
between the cab and the loading
ignition on.
area or to deactivate selective unlocking and
return to total unlocking mode, switch on the
With the remote control
ignition and press this button for more than two
► Depending on equipment,
seconds.
press one of these buttons to
An audible signal and, depending on equipment,
unlock the vehicle.
a display message, confirm that the request has
Selective unlocking unlocks either the cabin
been acknowledged.
Using the remote control with electric
doors, or the doors of the loading area (side
and rear).
sliding side door(s)
NOTICE
► To fully unlock the vehicle and open
the side door, press and hold this button
Selective unlocking between cab and loading
until the door has opened.
area is activated by default.
34
With Smart Entry & Start on your
With tailgate
Selective unlocking
person
To unlock the vehicle, the remote control must be
in recognition zone A.
► To unlock the vehicle fully, pass your hand
behind one of the door handles (front door(s),
NOTICE
manual sliding side door(s) or left-hand side-
hinged door) and then pull the handle to open
► With the Smart Entry & Start on your person,
Unlocking is signalled by rapid flashing of the
the corresponding door.
to unlock the vehicle, pull the tailgate handle
direction indicators for a few seconds.
With electric sliding side door(s)
and then lift it up to open it.
Depending on version, the door mirrors unfold
and the alarm is deactivated.
With an opening rear screen in the tailgate
With the remote control
► To unlock the cabin doors alone,
press this button once.
► To unlock the side and rear doors of the
loading area, press this button a second time.
If the vehicle is fitted with this function:
► Press this button to unlock the
► With the Smart Entry & Start on your person,
loading area only.
to unlock the vehicle, press the tailgate opening
► With the Smart Entry & Start on your person,
rear screen unlocking control. The screen will
Using the remote control with electric
pass your hand behind the handle to unlock the
open slightly; then, lift it up to open it.
sliding side door(s)
vehicle, then pull and release the handle. This
► To unlock the loading area alone
action also causes the corresponding door to
without opening the side door, press the
open.
relevant door button or keep the button pressed
down to open the door.
35
With Smart Entry & Start on your
With tailgate
NOTICE
person
Depending on the version, the door mirrors
unfold only when the cabin is unlocked, the
alarm is deactivated.
2
With electric sliding side door(s)
► With the Smart Entry & Start on your person,
► To unlock the cabin alone, pass your hand
to unlock the loading area, pull the tailgate
behind a handle of the front left or right doors,
handle and then lift it up.
then pull the handle to open the door.
NOTICE
NOTICE
Unlocking is signalled by rapid flashing of the
The door locking state of the loading area
direction indicators for a few seconds.
remains unchanged.
► With the Smart Entry & Start on your person,
pass your hand behind the left-hand or right-
hand door handle to unlock the loading area,
then pull and release the handle. This action also
causes the corresponding door to open.
► To unlock the loading area alone, the remote
control on your person in recognition zone A, B
or C, pass your hand behind a handle of the front
left or right doors, then pull the handle to open
the corresponding door.
36
With electric sliding side door(s)
Locking
NOTICE
► With the Smart Entry & Start on your person,
to lock the vehicle fully, press the markings on
If the vehicle is not fitted with an alarm,
With the key
one of the front door handles.
locking is signalled by fixed lighting of the
► To lock the vehicle fully, turn the key in the
direction indicators for approximately two
front left-hand door lock towards the rear of the
With tailgate
seconds.
vehicle.
Depending on version, the door mirrors fold at
If your vehicle has an alarm, it will not be
the same time.
activated.
With the remote control
WARNING
► To lock the vehicle completely, press
this button.
Driving with the doors locked could make it
► With the Smart Entry & Start on your person,
more difficult for the emergency services to
press the tailgate locking control to lock the
With Smart Entry & Start on
enter the passenger compartment in an
vehicle.
emergency.
your person
As a safety measure, never leave the vehicle
To lock the vehicle, the remote control must be in
NOTICE
without taking the remote control with you,
recognition zone A.
even for a short time.
Depending on version, keeping the
locking controls depressed closes the
windows. If the control is released, the
window stops in its current position.
WARNING
► To lock the vehicle, press the markings on
one of the door handles (front door(s), manual
Ensure that no person or object might prevent
sliding side door(s) or left-hand side-hinged
the windows from closing properly.
door).
Pay particular attention to children when
operating windows.
37
Deadlocking
With tailgate
NOTICE
WARNING
If the vehicle is not fitted with an alarm,
deadlocking is confirmed by fixed illumination
Deadlocking deactivates the exterior and
of the direction indicators for about two
interior door controls, as well as the central
seconds.
2
locking button on the dashboard.
The horn remains operational.
With Smart Entry & Start on your
► With the Smart Entry & Start on your person,
You must therefore never leave anyone inside
person
press the tailgate locking control to lock the
the vehicle when it is deadlocked.
entire vehicle.
To lock the vehicle, the remote control must be in
► To deadlock the vehicle, press the control
recognition zone A.
With the key
again within five seconds.
► To deadlock the vehicle, turn the key in the
front left-hand door lock towards the rear of the
NOTICE
vehicle.
If the vehicle is not fitted with an alarm,
► Then, within five seconds, turn the key
deadlocking is signalled by fixed lighting of
towards the rear again.
► To lock the vehicle fully, press the markings
the direction indicators for approximately two
on one of the door handles (front door(s),
With the remote control
seconds.
manual sliding side door(s) or left-hand side-
► To deadlock the vehicle, press this
hinged door).
button.
► To deadlock the vehicle, press the markings
► Then press this button again within five
again within five seconds.
seconds after locking.
With electric sliding side door(s)
NOTICE
► With the Smart Entry & Start on your person,
to lock the vehicle fully, press the markings on
At the same time, depending on version, the
one of the front door handles.
electric door mirrors fold in.
► To deadlock the vehicle, press the markings
again within five seconds.
38
► Turn the key rearwards again within
Back-up procedures
WARNING
5 seconds to deadlock the vehicle.
In the event of a malfunction of the central
Lost keys, remote control,
NOTICE
locking system, the battery must be
electronic key
disconnected to ensure that the vehicle is
If the vehicle is fitted with an alarm, it will not
Go to any authorized Toyota retailer or Toyota
locked fully.
be activated when locking with the key.
authorized repairer, or any reliable repairer
If the alarm is activated, the siren sounds
with the vehicle's registration certificate,
when the door is opened; switch on the
Front left-hand door
your personal identification documents and if
ignition to stop it.
possible, the label bearing the key code.
► Insert the key into the door lock.
Any authorized Toyota retailer or Toyota
► Turn the key towards the rear of the vehicle
authorized repairer, or any reliable repairer
to lock it, or towards the front to unlock it.
NOTICE
will be able to retrieve the key code and the
Front passenger door and sliding
transponder code, enabling a new key to be
If the vehicle is unlocked with the key in the
side door
ordered.
lock after locking it with the remote control
or the Smart Entry & Start system, all
Unlocking
Complete unlocking/locking
doors and the boot are unlocked.
► Pull the interior door opening handle.
If the vehicle is unlocked with the key in the
Locking
of the vehicle with the key
lock after locking it with the key, only the
► Open the door.
Use this procedure in the following situations:
doors (front door and sliding side door(s)) are
► For the side door, check that the child lock is
- Remote control battery discharged.
unlocked. The side-hinged doors and tailgate
not on. Refer to the corresponding section.
- Remote control malfunction.
are not unlocked. Switching on the ignition
- Vehicle battery discharged.
unlocks them.
- Vehicle in an area subject to strong
electromagnetic interference.
In the first case, change the remote control
Central locking not
battery.
functioning
Front passenger door
In the second case, reinitialise the remote
Use these procedures in the following cases:
control.
- Central locking malfunction.
Refer to the corresponding sections.
– Battery disconnected or discharged.
► Insert the key in the door lock.
► Turn the key towards the front/rear to unlock/
lock the vehicle.
39
Sliding side door
Unlocking the tailgate
Battery type: CR2032/3 volts.
► Remove the black cap on the edge of the
Without Smart Entry & Start
door, using the key.
► Insert the key in the aperture without
forcing it, then without turning it, move the latch
sideways towards the inside of the door.
2
► Remove the key and refit the black cap.
► Close the doors and check from the outside
that the vehicle is locked.
Side-hinged doors
► From inside the vehicle, insert a small
screwdriver into hole A on the lock to unlock the
Unlocking
tailgate.
► Use the interior opening handle.
► Move the latch to the left.
Locking
► If fitted to your vehicle, check that the electric
With Smart Entry & Start
NOTICE
child lock is not on.
► Open the left-hand side-hinged door.
If the fault persists after closing again, the
tailgate will remain locked.
Changing the battery
If the battery is flat, this warning lamp
comes on, accompanied by an audible
► Insert the key into the latch aperture on the
signal and the display of a message.
edge of the door (without forcing it) and slide the
assembly upwards.
► Remove the key.
► Close the door and check from the outside
► Unclip the cover by inserting a small
that the vehicle is locked.
screwdriver in the slot and lift the cover.
► Remove the flat battery from its housing.
► Put the new battery in place, respecting the
polarity. Start by inserting it into the contacts
40
located in the corner, then clip the cover onto
► Switch on the ignition by pressing the
the unit.
► Switch the ignition off.
"START/STOP" button.
► Reinitialise the remote control.
► Turn the key to position 2 (Ignition on).
If the fault persists after reinitialisation, contact
For more information on Reinitialising the
► Immediately press the closed padlock button
any authorized Toyota retailer or Toyota
remote control, refer to the corresponding
for a few seconds.
authorized repairer, or any reliable repairer
section.
► Switch off the ignition and remove the key
without delay.
from the ignition switch.
ECO
The remote control is now fully operational
Central locking
again.
Do not throw remote control batteries away,
as they contain metals that are harmful to the
With Smart Entry & Start
environment. Take them to an approved
disposal point.
Reinitialising the remote
control
Following replacement of the battery or in
the event of a fault, it may be necessary to
Manual
reinitialise the remote control.
► Press this button to lock/unlock the vehicle
Without Smart Entry & Start
(doors, tailgate or side-hinged doors) from inside
► Insert the mechanical key (incorporated into
the vehicle.
the remote control) into the lock to open the
The indicator lamp comes on to confirm the
vehicle.
central locking of the vehicle.
► Place the electronic key against the back-up
reader on the steering column and hold it there
WARNING
until the ignition is switched on.
► With a manual gearbox, place the gear lever
Central locking does not take place if any of
in neutral then fully depress the clutch pedal.
the doors are open.
► With an automatic gearbox or drive
selector, while in mode P, depress the brake
pedal.
41
► Press the button until an audible signal is
NOTICE
heard and/or a message appears on the screen.
When locking/deadlocking from the
Locking/unlocking the
outside
NOTICE
When the vehicle is locked or deadlocked
loading area
from the outside, the indicator lamp flashes
When transporting an oversized load (tailgate
2
and the button is deactivated.
or side-hinged doors open), press the button
► After normal locking, pull one of the
to lock only the front and rear doors (sliding
interior door controls to unlock the vehicle.
side door).
► After deadlocking, you must use the
remote control, the "Smart Entry & Start"
system or the built-in key to unlock the
NOTICE
vehicle.
When locking from inside, the door mirrors do
not fold.
WARNING
Central locking from the inside does not
operate if one of the doors is open (indicated
Driving with the doors locked makes access
by a mechanical noise coming from the
for the emergency services more difficult in an
NOTICE
locks).
emergency.
When the tailgate or side-hinged doors are
This button is unavailable if the vehicle has
open, only the other doors are locked (the
been locked or deadlocked from outside
button does not light up).
(using the key, remote control or Smart Entry
& Start, depending on equipment) or if any of
Automatic (anti-intrusion
the doors are still open.
NOTICE
security)
The doors and the tailgate or the side-hinged
Automatic
When transporting an oversized load (tailgate
or side-hinged doors open), press the button
doors can lock automatically while driving (speed
The loading area is always locked when driving.
to lock only the cab doors.
above 6 mph (10 km/h)).
To deactivate/reactivate this function (activated
by default):