Subaru Impreza (2019 year). Instruction - part 9

(135,1)

北米Model "A1350BE-A" EDITED: 2018/ 4/ 20

NOTE

The default setting for this function

is set as “operational”. The operational/
non-operational setting of this function
can be changed by a SUBARU dealer.
Contact your SUBARU dealer to
change the setting.
.

When leaving the vehicle, please

make sure that all doors and the rear
gate (5-door models) are completely
closed.
.

The battery drainage prevention

function does not operate while the
key is in the ignition switch.

Alarm system

The alarm system helps to protect your
vehicle and valuables from theft. The horn
sounds and the hazard warning flashers
flash if someone attempts to break into
your vehicle.

For models with “keyless access with
push-button start system”:
The system can be armed or disarmed
with the keyless access function or access
key fob.
The system will not be activated when the
push-button ignition switch is in the “ACC”
or “ON” position.

For models without “keyless access
with push-button start system”:
The system can be armed or disarmed
with the remote transmitter.
The system will not be activated when the
key is inserted into the ignition switch.

Your vehicle’s alarm system has been set
for activation at the time of shipment from
the factory. You can set the system for
deactivation yourself or have it done by
your SUBARU dealer.

Alarm system operation

When the alarm system is armed, it is
triggered by opening any of the doors, the
engine hood, the rear gate (5-door mod-
els) or the trunk lid (sedan).
The alarm system will activate the follow-
ing alarms when triggered.
.

The vehicle’s horn will sound for 30

seconds.
.

The hazard warning flashers will flash

for 30 seconds.

If any of the doors, the engine hood or the
rear gate/trunk lid remains open after the
30-second period, the horn will continue to
sound for a maximum of 3 minutes. If the
door, the engine hood or the rear gate/
trunk lid is closed while the horn is
sounding, the horn will stop sounding with
a delay of up to 30 seconds.

NOTE

The alarm system can be set to illumi-
nate the following interior lights.
.

Map lights (illuminates only when

the map lights switch is in the “DOOR”
position)
.

Dome light (illuminates only when

the dome light switch is in the “DOOR”
position)

– CONTINUED –

Keys and doors/Alarm system

2-27

(136,1)

北米Model "A1350BE-A" EDITED: 2018/ 4/ 20

Cargo area light (illuminates only

when the cargo area light switch is in
the “DOOR” position)

The notifications regarding the map
lights, dome light and cargo area light
are deactivated as the factory setting. A
SUBARU dealer can activate the sys-
tem. Contact your SUBARU dealer for
details.

Arming the system

The alarm system becomes armed when
the following operation is performed.
1. Close all windows and the moonroof (if
equipped) and turn the ignition switch to
the “OFF” position.
2. Carry the key and get out of the
vehicle.
3. Make sure that the engine hood is
closed.
4. Lock the doors using any of the
following methods.

Locking using the remote keyless

entry system. For details, refer to
“Remote keyless entry system” F2-20.
.

Locking using the keyless access

function (if equipped). For details, refer
to “Locking with the door lock sensor”
F2-10.

Locking using the power door lock-

ing switch. For details, refer to “Locking
using power door locking switch” F2-
25.

NOTE

Security indicator light

All doors and the rear gate (5-door

models) will lock, an electronic chirp
will sound once, the hazard warning
flashers will flash once, and the secur-
ity indicator light will start flashing
rapidly.
.

If any of the doors or the rear gate/

trunk lid is not fully closed, an electro-
nic chirp sounds five times, the hazard
warning flashers flash five times to
alert you that the doors (or the rear

gate/trunk lid) are not properly closed.
When you close the door, doors will
automatically lock.

5. Approximately 30 seconds later, the
system will enter surveillance state.

When the system is in surveillance state,
the security indicator light will then flash
slowly (twice approximately every 2 sec-
onds), indicating that the system has been
armed for surveillance.

NOTE

The system can be armed even if the

windows and/or moonroof are open.
Always make sure that they are fully
closed before arming the system.
.

The 30-second standby time can be

eliminated if you prefer. Have it per-
formed by your SUBARU dealer.
.

For sedan, if you open the trunk

using the access key fob/remote trans-
mitter’s “

” button with the alarm

system armed, the system will be
temporarily placed in a standby state.
The system will go back to the surveil-
lance state upon locking the trunk.

Keys and doors/Alarm system

2-28

(137,1)

北米Model "A1350BE-A" EDITED: 2018/ 4/ 20

If any of the following actions is

done during the standby period, the
system will not switch to the surveil-
lance state.

– Doors (including the rear gate/
trunk lid) are unlocked using the
access key fob/remote transmitter.
– Doors (including the rear gate/
trunk lid) are unlocked using the
keyless access function (models
with “keyless access with push-
button start system”).
– Any door (including the rear gate/
trunk lid) is opened.
– The ignition switch is turned to
the “ON” position (models without
“keyless access with push-button
start system”).
– Push-button ignition switch is
turned to the “ACC” position (mod-
els with “keyless access with push-
button start system”).

Disarming the system

Perform either of the following procedures.
.

Briefly press a button (for less than 2

seconds) on the access key fob/remote
transmitter.
.

Carry the access key fob and perform

either of the following procedures (models
with “keyless access with push-button
start system”).

– Grip the front door handle.
– Press the rear gate opener button
(5-door models).
– Unlock using the PIN code access.

The flashing of the security indicator light
will then change slowly (once approxi-
mately every 3 seconds from twice ap-
proximately every 2 seconds), indicating
that the alarm system has been disarmed.

Emergency disarming

If you cannot disarm the system using the
access key fob/transmitter (i.e. the trans-
mitter is lost, broken or the transmitter
battery is too weak), you can disarm the
system without using the access key fob/
remote transmitter.
The system can be disarmed if you turn the
ignition switch from the “LOCK”/“OFF” to
the “ON” position with a registered key/
access key fob.

NOTE

For models with “keyless access with
push-button start system”, if the ac-
cess key fob battery is discharged,
perform the procedure described in
“Switching power status” F9-19. In
such a case, replace the battery im-
mediately. Refer to “Replacing battery
of access key fob” F11-48.

Alarm system setting

To change the setting of your vehicle’s
alarm system for activation or deactiva-
tion, do the following.
1. Disarm the alarm system. Refer to
“Disarming the system” F2-29.
2. Sit in the driver’s seat and shut all
doors, the engine hood and the rear gate
(5-door models).
3. Turn the ignition switch to the “ON”
position.
4. Hold down the unlock side of the
driver’s power door locking switch, open
the driver’s door within the following 1
second, and wait 10 seconds without
releasing the switch. The setting will then
be changed as follows.

– CONTINUED –

Keys and doors/Alarm system

2-29

(138,1)

北米Model "A1350BE-A" EDITED: 2018/ 4/ 20

Type A combination meter

Setting

status

Combination

meter display

Horn

Activate

AL on

Once

Deactivate

AL oF

Twice

Type B combination meter

Setting

status

Combination

meter display

Horn

Activate

AL ON

Once

Deactivate

AL OFF

Twice

NOTE

You may have the above setting change
done by your SUBARU dealer.

If you have accidentally trig-
gered the alarm system

To stop the alarm

Do any of the following operations:
.

Press any button on the access key fob/

remote transmitter.
.

Turn the ignition switch to the “ON”

position (models without “keyless access
with push-button start system”).
.

Turn the push-button ignition to the

“ACC” position (models with “keyless
access with push-button start system”).

NOTE

Only registered keys will stop the
alarm. If the immobilizer transponder
is not registered, the alarm will not
stop.

Valet mode

When you choose the valet mode, the
alarm system does not operate. In valet
mode, the remote transmitter is used only
for locking and unlocking the doors and
rear gate (5-door models) and panic
activation.

To enter the valet mode, change the
setting of your vehicle’s alarm system for
deactivation mode. Refer to “Alarm system
setting” F2-29. The security indicator light
will continue to flash once every 3 seconds
indicating that the system is in the valet
mode.

To exit valet mode, change the setting of
your vehicle’s alarm system for activation
mode. Refer to “Alarm system setting” F2-
29.

Child safety locks

Each rear door has a child safety lock.
When the child safety lock lever is in the
lock position, the door cannot be opened
from inside. The door can only be opened
from the outside.

WARNING

Always turn the child safety locks to
the “LOCK” position when children
sit in the rear seat. Serious injury
could result if a child accidentally
opens the door and falls out.

Keys and doors/Child safety locks

2-30

(139,1)

北米Model "A1350BE-A" EDITED: 2018/ 4/ 20

Windows

WARNING

To avoid serious personal injury
caused by entrapment, always con-
form to the following instructions
without exception.

When operating the power win-

dows, be extremely careful to
prevent anyone’s fingers, arms,
neck, head or other objects from
being caught in the window.

Always lock the passengers’ win-

dows using the lock switch when
children are riding in the vehicle.

Always carry the key when you

leave the vehicle for safety rea-
sons and never allow an unat-
tended child to remain in the
vehicle. Failure to follow this
procedure could result in injury
to a child operating the power
window.

The power windows operate only when the
ignition switch is in the “ON” position.

Power window operation

Power window switches

Driver’s side power window switches:

For front left window (with one-touch auto
up and down feature)

For front right window (with one-touch
auto up and down feature)

For rear left window

For rear right window

Lock switch

All door windows can be controlled by the
power window switch cluster at the driver
side door.

Passenger ’s side power window

switches:

Each passenger window can be controlled
by the power window switch located on the
door.

– CONTINUED –

Keys and doors/Windows

2-31

(140,1)

北米Model "A1350BE-A" EDITED: 2018/ 4/ 20

Operating the window

With one-touch auto up and down

feature:

Automatically close*

Open

Automatically open*

*: To stop the window halfway, operate the

switch to opposite side.

NOTE

Avoid the following.
.

After the driver’s window is fully

closed or fully opened, the switch is
continuously operated in the same
direction for a few seconds.
.

After the windows for three or more

seats are fully closed or fully opened,
each switch is continuously operated

in the same direction simultaneously
for a few seconds.
Either of the operations described
above may cause the power window
breaker to operate making it impossible
to open or close the window. Be sure to
initialize the power windows. If they are
not initialized, the one-touch auto up/
down function will not operate. Refer to
“Initialization of power window with
one-touch auto up/down function”
F2-33.

Without one-touch auto up and down

feature:

Open

Anti-entrapment function (windows
with one-touch auto up/down func-
tion)

While closing the driver’s and front pas-
senger’s windows automatically, if the
window senses a substantial enough
object trapped between the window and
the window frame, it automatically moves
down slightly and stops.
If a foreign object is caught while the
driver’s window or passenger’s window is
opening automatically, the window will
stop.

CAUTION

Never attempt to test this func-

tion using fingers, hands or other
parts of your body.

The anti-entrapment function

may not operate properly if some
object gets trapped just before
the window fully closes.

NOTE

If a window detects an impact similar

to that caused by trapping an object (for
example, when the vehicle encounters
a deep pothole), the anti-entrapment
function may operate.

Keys and doors/Windows

2-32

(141,1)

北米Model "A1350BE-A" EDITED: 2018/ 4/ 20

The window cannot be operated for a

few seconds after the anti-entrapment
function operates.

Off delay function (windows with
one-touch auto up/down function)

The front windows can be operated for
approximately 45 seconds even after the
ignition switch is turned to the “ACC” or
“OFF” position. If a front door is opened
within 45 seconds, the off delay function is
canceled.

Locking the passengers’ windows

Lock

Unlock

When the lock switch is in the lock position,
the passengers’ windows cannot be
opened or closed.

Initialization of power window
with one-touch auto up/down
function

If the power window automatic function
(one-touch auto up and down function)
does not operate properly, operate each
window according to the following proce-
dure in order to initialize the power window
system.
1. Close the door.
2. Turn the ignition switch to the “ON”
position.
3. Open the window completely and then
press and hold down the power window
switch for approximately 1 second.
4. Close the window completely and then
pull and hold the power window switch for
approximately 1 second.

Trunk lid (sedan)

WARNING

To prevent dangerous exhaust

gas from entering the vehicle,
always keep the trunk lid closed
while the engine is running.

Help prevent children, adults or

animals from locking themselves
in the trunk. On hot or sunny
days, the temperature in the trunk
could quickly become high en-
ough to cause death or serious
heat-related injuries including
brain damage to anyone locked
inside, particularly for small chil-
dren.

When leaving the vehicle, either

close all windows and lock all
doors. Also make certain that the
trunk is closed.

– CONTINUED –

Keys and doors/Trunk lid (sedan)

2-33

(142,1)

北米Model "A1350BE-A" EDITED: 2018/ 4/ 20

To open and close the trunk
lid from outside

The trunk lid can be opened using the
keyless access function or remote keyless
entry system. For details, refer to the
following section.
.

For models with “keyless access with

push-button start system”, refer to “Open-
ing trunk (sedan)” F2-11 or “Opening the
trunk lid (sedan)” F2-21.
.

For models without “keyless access

with push-button start system”, refer to
“Opening the trunk lid (sedan)” F2-21.

To close the trunk lid, lightly press the trunk
lid down until the latch engages.

NOTE

Do not leave your valuables in the

trunk when you leave your vehicle.
.

Under the following conditions, the

trunk can be opened without the access
key fob.

– the trunk lock/unlock setting is
set to on
– all doors are unlocked

The trunk lock/unlock setting can be
changed by a SUBARU dealer. Contact
your SUBARU dealer to change the
setting.

To open the trunk lid from
inside

Pull the trunk lid release lever upward. The
lever is on the floor at the left of the driver’s
seat.

Internal trunk lid release
handle

The internal trunk lid release handle is a
device designed to open the trunk lid from
inside the trunk. In the event children or
adults become locked inside the trunk, the
handle allows them to open the lid. The
handle is located on the inside of the trunk
lid.

To open the trunk lid from inside the trunk,
pull the trunk lid release handle upward as
indicated by the arrow on the handle.
This operation unlocks the trunk lid. Then,
push up the lid.

The handle is made of material that
remains luminescent for approximately
an hour in the dark trunk space after it is
exposed to ambient light even for a short
time.

WARNING

Never allow any child to get in the
trunk and play with the release
handle. If the driver starts the vehi-
cle without knowing that a child is
inside the trunk and the child opens
the lid using the release handle, the

Keys and doors/Trunk lid (sedan)

2-34

(143,1)

北米Model "A1350BE-A" EDITED: 2018/ 4/ 20

child could fall out and be killed or
seriously injured.

CAUTION

Do not close the lid while gripping

the release handle. The handle
may be damaged.

Do not use the handle as a hook

to fasten straps or ropes to
secure your cargo in the trunk.
Such use may result in damage of
the handle.

Load the trunk so that cargo

cannot strike the release handle.
If the cargo hits the handle while
the vehicle is being driven, the
handle may be pulled up and the
trunk lid may open. That may
cause cargo to fall out of the
trunk, which could create a traffic
safety hazard.

Inspection

Perform the following steps at least twice a
year to check the release handle for
correct operation.
1. Open the trunk lid.

2. Use a flat-head screwdriver with a thin
blade. Slide the flat-head screwdriver
blade from the slit aperture of the lock
assembly fully to the end until you hear a
click.

This places the latch in the locked position.

3. Pull the release handle upward and
check that the latch is released.

If the latch is not released, contact your
SUBARU dealer.
In this case, press the “

” button on the

key lug to release the latch, then close the
trunk lid.
Also, if the movement of the trunk lid
release handle feels restricted or not
entirely smooth during operation, or the
handle and/or handle base is cracked,
contact your SUBARU dealer.

Keys and doors/Trunk lid (sedan)

2-35

(144,1)

北米Model "A1350BE-A" EDITED: 2018/ 4/ 20

Rear gate (5-door models)

WARNING

To prevent dangerous exhaust

gas from entering the vehicle,
always keep the rear gate closed
while the engine is running.

Do not attempt to shut the rear

gate while holding the recessed
grip. Also avoid closing the rear
gate by pulling on the recessed
grip from inside the cargo space.
There is a danger of your hand
being caught and injured.

NOTE

If the rear gate cannot be unlocked due
to a discharged vehicle battery, a mal-
function in the door locking/unlocking
system or other causes, you can unlock
it by manually operating the rear gate
lock release lever.
For the procedure, refer to “Rear gate –
if the rear gate cannot be opened” F9-
20.

Lock/unlock

The rear gate can be locked and unlocked
using any of the following systems.
.

Power door locking switch: Refer to

“How to operate the power door locking
switches” F2-25.
.

Keyless access with the push-button

start system (if equipped): Refer to “Key-
less access with push-button start system”
F2-3.
.

Remote keyless entry system: Refer to

“Remote keyless entry system” F2-20.

Open/close

The rear gate opener button

To open:
First unlock the rear gate lock then push
the rear gate opener button.

To close:
Lower the rear gate slowly and push down
firmly until the latch engages.
The rear gate can be lowered easily if you
pull it down holding the recessed grip.

CAUTION

Do not jam a plastic bag in or

place cellophane tape on the rear
gate stays or scratch the stays
while loading or unloading cargo.
That could cause leakage of gas
from the stays, which may result
in their inability to hold the rear
gate open.

Keys and doors/Rear gate (5-door models)

2-36

(145,1)

北米Model "A1350BE-A" EDITED: 2018/ 4/ 20

Be careful not to hit your head or

face on the rear gate when open-
ing or closing the rear gate and
when loading or unloading cargo.

Moonroof (if equipped)

WARNING

Never let anyone’s hands, arms,
head or any objects protrude from
the moonroof. A person could be
seriously injured if any of the follow-
ing conditions occur.

The vehicle stops suddenly.

The vehicle turns sharply.

The vehicle is involved in an

accident.

Body parts protruding from the

vehicle are struck by outside
objects.

To avoid serious personal injury
caused by entrapment, always con-
form to the following instructions
without exception.

Before closing the moonroof,

make sure that no one’s hands,
arms, head or other objects will
be accidentally caught in the
moonroof.

Always carry the key when you

leave the vehicle for safety rea-
sons and never allow an unat-
tended child to remain in the

vehicle. Failure to follow this
procedure could result in injury
to a child operating the moon-
roof.

Never try to check the anti-en-

trapment function by deliberately
placing part of your body in the
moonroof.

CAUTION

Do not sit on the edge of the open

moonroof.

Do not operate the moonroof if

falling snow or extremely cold
conditions have caused it to
freeze shut.

The anti-entrapment function

does not operate when the moon-
roof is being tilted down. Be sure
to confirm that it is safe to do so
before tilting the moonroof down.

If the moonroof does not close,

have the system checked by a
SUBARU dealer.

The moonroof has both tilting and sliding
functions.

The moonroof operates only when the
ignition switch is in the “ON” position.

– CONTINUED –

Keys and doors/Moonroof

2-37

(146,1)

北米Model "A1350BE-A" EDITED: 2018/ 4/ 20

Moonroof switches

Tilting moonroof

Down

To raise the moonroof, press and hold the
switch in the up side and release. To lower
the moonroof, press and hold the switch in
the down side.

NOTE

Release the switch after the moonroof
has been raised or has been lowered
completely. Pressing the switch con-
tinuously may cause damage to the
moonroof.

Sliding moonroof

Open

To open or close the moonroof using the
automatic function, press and hold the
switch toward the open/close side and
release.
To stop the moonroof halfway, press a
switch on the moonroof switch.

NOTE

After washing the vehicle or after it
rains, wipe away water on the roof prior
to opening the moonroof to prevent
drops of water from falling into the
passenger compartment.

Anti-entrapment function

When the moonroof senses a substantial
enough object trapped between its glass
and the vehicle’s roof during closure, it
automatically moves back to the fully open
position and stops there. The anti-entrap-
ment function may also be activated by a
strong shock on the moonroof even when
there is nothing trapped.

CAUTION

Never attempt to test this function
using fingers, hands or other parts
of your body.

NOTE

For the sake of safety, it is recom-
mended that you avoid driving with the
moonroof fully opened.

Keys and doors/Moonroof

2-38

(147,1)

北米Model "A1350BE-A" EDITED: 2018/ 4/ 20

Sun shade

The sun shade can be slid forward or
backward by hand while the moonroof is
closed.
If the moonroof is opened, the sun shade
also moves back.

Keys and doors/Moonroof

2-39

(2,1)

Model "ALL_MODEL_MEMO" EDITED: 2017/ 11/ 6

Left Page

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

(149,1)

北米Model "A1350BE-A" EDITED: 2018/ 4/ 20

Ignition switch (models without “keyless

access with push-button start system”) ............ 3-4

Key positions......................................................... 3-4
Key reminder chime ............................................... 3-5
Ignition switch light (if equipped) ........................... 3-6

Push-button ignition switch (models with

“keyless access with push-button start
system”) ............................................................... 3-6

Safety precautions ................................................. 3-6
Operating range for push-button start system ........ 3-6
Switching power status .......................................... 3-7
When access key fob does not operate properly .... 3-8

Hazard warning flasher .......................................... 3-8
Meters and gauges ................................................. 3-9

Speedometer ......................................................... 3-9
Tachometer ............................................................ 3-9
Odometer............................................................... 3-9
Double trip meter ................................................... 3-9
Fuel gauge............................................................ 3-10
ECO gauge (if equipped) ....................................... 3-11
Combination meter settings .................................. 3-11

Illumination brightness control............................ 3-12

Auto dimmer cancel function (if equipped) ............ 3-12

Warning and indicator .......................................... 3-13

Initial illumination for system check ...................... 3-13
Seatbelt warning light and chime .......................... 3-14
SRS airbag system warning light........................... 3-15
Front passenger’s frontal airbag ON and OFF

indicators ........................................................... 3-15

CHECK ENGINE warning light/Malfunction

indicator light ..................................................... 3-16

Coolant temperature low indicator light/Coolant

temperature high warning light .......................... 3-17

Charge warning light ............................................ 3-18
Oil pressure warning light..................................... 3-18
Engine low oil level warning light.......................... 3-18
Windshield washer fluid warning light................... 3-19
AT OIL TEMP warning light (CVT models).............. 3-19
Low tire pressure warning light

(U.S.-spec. models)............................................ 3-19

ABS warning light................................................. 3-20
Brake system warning light (red) .......................... 3-21
Low fuel warning light .......................................... 3-22
Hill start assist warning light/Hill start assist

OFF indicator light............................................. 3-22

Door open warning light ....................................... 3-22
All-Wheel Drive warning light (CVT models) .......... 3-23
Power steering warning light ................................ 3-23
Vehicle Dynamics Control warning light/Vehicle

Dynamics Control operation indicator light ........ 3-24

Vehicle Dynamics Control OFF indicator light ....... 3-25
Warning chimes and warning indicator of the

keyless access with push-button start system
(if equipped) ...................................................... 3-25

Security indicator light.......................................... 3-30
Select lever/gear position indicator

(CVT models)..................................................... 3-31

Turn signal indicator lights ................................... 3-31
High beam indicator light...................................... 3-31
High beam assist indicator light (if equipped) ....... 3-31
Cruise control indicator light (if equipped) ............ 3-32
Cruise control set indicator light (if equipped)....... 3-32

Instruments and controls

(150,1)

北米Model "A1350BE-A" EDITED: 2018/ 4/ 20

Automatic headlight beam leveler warning light

(models with LED headlights).............................. 3-32

LED headlight warning light (models with LED

headlights).......................................................... 3-32

Steering Responsive Headlight warning light/

Steering Responsive Headlight OFF indicator
light (if equipped)................................................ 3-32

Front fog light indicator light (if equipped) ............ 3-32
Headlight indicator light (if equipped).................... 3-32
Steering responsive fog lights warning indicator/

Steering responsive fog lights OFF indicator (if
equipped) ........................................................... 3-33

BSD/RCTA warning indicator (if equipped)............. 3-33
BSD/RCTA OFF indicator (if equipped) .................. 3-33
RAB warning indicator (if equipped) ...................... 3-33
RAB OFF indicator light (if equipped) .................... 3-33
Icy road surface warning indicator (if equipped) .... 3-33

Combination meter display (color LCD)

(if equipped) ....................................................... 3-34

Basic operation..................................................... 3-35
Welcome screen (opening animation) and

Good-bye screen (ending animation) ................... 3-35

Warning screen..................................................... 3-36
Telltale screen....................................................... 3-36
Basic screens ....................................................... 3-37
Menu screens ....................................................... 3-39

Multi-function display (black and white) ............. 3-41

Driving information display ................................... 3-41
Outside temperature indicator ............................... 3-45
Clock .................................................................... 3-46

Multi-function display (color LCD)

(if equipped) ....................................................... 3-46

Features ............................................................... 3-47
Welcome screen ................................................... 3-47
Self-check screen ................................................. 3-47
Interruption screen ............................................... 3-48
Basic operation .................................................... 3-48
Basic screens....................................................... 3-49
Setting screen ...................................................... 3-56
How to get the source code using the open

source............................................................... 3-61

Clock...................................................................... 3-61

Setting the clock manually.................................... 3-61
Setting the clock automatically ............................. 3-64
Regulatory information ......................................... 3-65

Light control switch ............................................. 3-65

Precautions and tips............................................. 3-65
Headlights ............................................................ 3-66
High/low beam change (dimmer) ........................... 3-67
Headlight flasher .................................................. 3-68
High beam assist function (if equipped) ................ 3-68
Daytime running light system ............................... 3-71

Steering Responsive Headlight (SRH)

(if equipped) ....................................................... 3-71

Headlight beam leveler (models with LED

headlights) ......................................................... 3-72

Fog light switch (if equipped).............................. 3-73

Steering responsive fog lights system

(if equipped) ...................................................... 3-73

Instruments and controls

Content .. 7 8 9 10 ..