Subaru Impreza (2019 year). Instruction

(119,1)

北米Model "A1350BE-A" EDITED: 2018/ 4/ 20

Opening rear gate (5-door mod-
els)

Rear gate opener button

Carry the access key fob, and press the
rear gate opener button. Either only the
rear gate will unlock, or all doors will
unlock. Also, an electronic chirp will sound
twice and the hazard warning flashers will
flash twice.

Opening trunk (sedan)

Trunk opener button

Carry the access key fob, and press the
trunk opener button. The trunk will open.
An electronic chirp will sound twice and the
hazard warning flashers will flash twice.

NOTE

Under the following conditions, the
trunk can be opened without the key
fob.
.

the trunk lock/unlock setting is set to

on
.

all doors are unlocked

The trunk lock/unlock setting can be
changed by a SUBARU dealer. Contact
your SUBARU dealer to change the
setting.

Door unlock selection function

When the door is unlocked using the
keyless access function, only the doors
that were set can be unlocked.
The settings can be changed with the
following methods.
.

The setting can be changed by operat-

ing the combination meter display (color
LCD) (if equipped). Refer to “Keyless Entry
System” F3-40.
.

The setting can be changed by a

SUBARU dealer.

– CONTINUED –

Keys and doors/Keyless access with push-button start system

2-11

(120,1)

北米Model "A1350BE-A" EDITED: 2018/ 4/ 20

Unlock using PIN Code Ac-
cess

When all doors including the rear gate (5-
door models) are locked, you can unlock
the doors (including rear gate) without a
key by performing the following procedure.
.

Sedan: press the trunk opener button

5-door models: press the rear lock

button

Trunk opener button (sedan)

Rear lock button (5-door models)

NOTE

PIN Code Access will be helpful if the
key fob is accidentally left in the
vehicle. It is recommended that a 5-
digit security code (PIN code) be regis-
tered.

Preparation for registering a PIN
code

1. Turn off the ignition switch.
2. Close all doors (including trunk/rear
gate).
3. Press and hold the “ ” button on the
access key fob. Then all doors (including
rear gate) will be locked.
4. Keep the “ ” button pressed, and
press the trunk opener button (sedan)/rear

lock button (5-door models) within 5
seconds after step 3.
5. Press and hold the trunk opener button
(sedan)/rear lock button (5-door models)
for more than 5 seconds. Confirm a chirp
sound.
6. Release the “ ” button and trunk
opener button (sedan)/rear lock button
(5-door models).
7. Press the “ ” button on the access key
fob while the chirp sounds.
Then the chirp will stop and the prepara-
tion is complete.

NOTE

Press the “ ” button within 30 seconds
of step 6 to end the preparation mode
and move on to the registration stage.
Unless the “ ” button is pressed within
30 seconds after step 6, the PIN code
registration will be canceled.

Registration for a PIN code

For example, to register “32468” as the
PIN code, perform the following proce-
dure.
1. Press the trunk opener button (sedan)/
rear lock button (5-door models) three
times.
2. After a chirp sounds once, press the
trunk opener button (sedan)/rear lock

Keys and doors/Keyless access with push-button start system

2-12

(121,1)

北米Model "A1350BE-A" EDITED: 2018/ 4/ 20

button (5-door models) twice.
3. After a chirp sounds once, press the
trunk opener button (sedan)/rear lock
button (5-door models) four times.
4. After a chirp (ding) sounds once, press
the trunk opener button (sedan)/rear lock
button (5-door models) six times.
5. After a chirp (ding) sounds once, press
the trunk opener button (sedan)/rear lock
button (5-door models) eight times.
6. Perform steps 1 to 5 again within
approximately 30 seconds after the chirp
starts sounding intermittently.
7. All doors will be unlocked and locked.
Then the PIN code will be registered.

NOTE

Press the trunk opener button (se-

dan)/rear lock button (5-door models)
ten times to enter “0”.
.

Change the PIN code frequently to

protect your vehicle from theft.
.

If you have lent your vehicle to

another person, confirm that the PIN
code has not been changed or deleted.
If the PIN code has been changed or
deleted, reregister a new PIN code.
.

If you make an error during the

registration procedure, press the “ ”
or “

” button on the access key fob.

Then, start over from the procedure

described in “Preparation for register-
ing a PIN code”.
.

To protect your vehicle from theft,

you cannot register a string of the same
five numbers together, such as
“00000”, nor “12345” as a PIN code.
.

Do not register your vehicle license

plate number or simple numbers such
as “11122” or “12121” as a PIN code.
Doing so will increase the risk of
vehicle theft.
.

When you try to register “22222”, the

registered PIN code will be deleted. You
cannot unlock the doors by PIN Code
Access until a new code is registered.
.

After registering a new PIN code,

make sure that you can unlock the
doors using the PIN code.
.

The PIN code cannot be deleted

while the keyless access function is
disabled by operating the access key
fob.
.

Reregister the PIN code in the fol-

lowing case.

– when you forget the PIN code
– when you want to change the PIN
code

Unlocking

Perform steps 1 to 5 described in “Regis-
tration for a PIN code”.

NOTE

You cannot unlock by PIN Code

Access in the following cases.

– when the access key fob is within
the operating ranges
– when the ignition switch is in the
“ACC” or “ON” position

If you make an operation error dur-

ing the unlocking procedure, start over
with the unlocking procedure after
waiting for 5 seconds or longer.
.

To protect your vehicle from theft, a

buzzer will sound if incorrect PIN codes
are entered five times continuously. If
this occurs, you cannot unlock the
doors by PIN Code Access for 5
minutes.

– CONTINUED –

Keys and doors/Keyless access with push-button start system

2-13

(122,1)

北米Model "A1350BE-A" EDITED: 2018/ 4/ 20

Power saving function

The keyless access function will be dis-
abled in the following cases to protect the
access key fob battery and the vehicle
battery.
.

Case 1: When the keyless access

function and the remote keyless entry
system have not been used for 2 weeks
or longer while all doors are locked

Operate one of the following items to
recover the keyless access function:

– Unlock the doors by operating any
procedure other than gripping the front
passenger’s door handle
– Lock the doors
– Open a door and then close it

Case 2: When the access key fob has

been left in the operating range for 10
minutes or longer while all doors are
locked

Operate one of the following items to
recover the keyless access function:

– Unlock the doors by gripping the
door handle
– Unlock the doors by pressing the
rear gate opener button
– Lock the doors by touching the door
lock sensor
– Lock or unlock the doors by using

the remote keyless entry system
– Lock or unlock the doors by using
the power door locking switch
– Open either of the front doors

Power saving function of ac-
cess key fob

This function stops the access key fob
from receiving signals and helps minimize
the battery consumption of the access key
fob.
1. Press the “ ” button twice while hold-
ing the “ ” button.

LED indicator

2. Confirm that the LED indicator blinks 4
times to notify that the setting is complete.
When the access key fob is in the power
save mode, the keyless access function

and push-button start system will not be
available.
To cancel the power save mode, press one
of the buttons on the access key fob.

Disabling keyless access
function

WARNING

If you wear an implanted pacemaker
or an implanted defibrillator, per-
form the procedure described in
“By operating the driver’s door”
F2-15 to disable the keyless access
function. If you perform the proce-
dure described in “By operating the
access key fob” F2-15, the opera-
tion of an implanted pacemaker or
implanted defibrillator may be af-
fected by the radio waves from the
transmitter antenna.

When the vehicle is not going to be used
for a long time, or when you choose not to
use the keyless access function, the key-
less access function can be disabled.

NOTE

The locking and unlocking function

by the remote keyless entry system is
not disabled.

Keys and doors/Keyless access with push-button start system

2-14

(123,1)

北米Model "A1350BE-A" EDITED: 2018/ 4/ 20

To start the engine while the func-

tions are disabled, perform the proce-
dure described in “Starting engine”
F9-19.

Disabling functions

By operating the access key fob

If you have registered a PIN code for PIN
Code Access, you can disable the keyless
access function by operating the access
key fob. For details about registering a PIN
code, refer to “Preparation for registering a
PIN code” F2-12.
1. Open the driver’s door.
2. Rotate the lock lever toward the lock
position.

3. Press and hold the “ ” button and “

”

button on the access key fob simulta-

neously for more than 5 seconds.

A chirp sound will be heard, and the
function will be disabled.

By operating the driver’s door

1. Sit in the driver’s seat, and close the
door (5–door models).

2. Push the unlock side of the power door
locking switch.
3. Within 5 seconds after step 2 is
performed, open the driver’s door.
4. Within 5 seconds after step 3 is
performed, push the unlock side of the
power door locking switch twice while the
door is open.
5. Within 10 seconds after step 4 is
performed, close and open the driver’s
door twice.

6. Within 10 seconds after step 5 is
performed, push the unlock side of the
power door locking switch twice while the
door is open.
7. Within 10 seconds after step 6 is
performed, close and open the driver’s
door once.
8. Within 5 seconds after step 7 is
performed, close the door.

A chirp sound will be heard, and the
functions will be disabled.

NOTE

In steps 4 and 6, press the power door
locking switch slowly. If the switch is
pressed quickly, the functions may not
be disabled.

– CONTINUED –

Keys and doors/Keyless access with push-button start system

2-15

(124,1)

北米Model "A1350BE-A" EDITED: 2018/ 4/ 20

Enabling functions

When the procedure to disable the func-
tions is performed again, a chirp sound will
be heard, and the functions are enabled.

NOTE

The keyless access function will be

enabled only if you perform the proce-
dure in the same manner you disabled
the function (for example, when dis-
abling by operating the driver’s door,
the function will not be enabled even if
you operate the access key fob).
.

Press the push-button ignition

switch if you do not know the proce-
dure in which the keyless access func-
tion was disabled.

– When disabling by operating the
driver’s door: a chirp will not be
heard
– When disabling by operating the
access key fob: a chirp will be heard

Selecting audible signal op-
eration

Using an electronic chirp, the system will
give you an audible signal when the doors
lock and unlock. If desired, you may turn
the audible signal off. For more details,
contact a SUBARU dealer.

NOTE

For models with the combination meter
display (color LCD), the setting can be
changed by operating the combination
meter display (color LCD). For details,
refer to “Vehicle Setting” F3-40.

Warning chimes and warning
indicator

The warning chime and the access key
warning light serve the following purposes:
.

To minimize improper operation of the

keyless access with push-button start
system.
.

To protect your vehicle from theft.

For details, refer to “Warning chimes and
warning indicator of the keyless access
with push-button start system” F3-25.

When access key fob does
not operate properly

Refer to “Access key fob – if access key
fob does not operate properly” F9-18.

Replacing battery of access
key fob

Refer to “Replacing battery of access key
fob” F11-48.

Replacing access key fob

Access key fobs can be replaced at
SUBARU dealers. For more details, con-
tact a SUBARU dealer.

Keys and doors/Keyless access with push-button start system

2-16

(125,1)

北米Model "A1350BE-A" EDITED: 2018/ 4/ 20

Certification for keyless ac-
cess with push-button start
system

U.S.-spec. models

FCC ID: HYQ14AHK
FCC ID: Y8PFJ16-1
FCC ID: Y8PSSPIMB02

CAUTION

FCC WARNING

Changes or modifications not ex-
pressly approved by the party re-
sponsible for compliance could void
the user’s authority to operate the
equipment.

NOTE

This device complies with part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This de-
vice may not cause harmful interfer-
ence, and (2) this device must accept
any interference received, including
interference that may cause undesired
operation.

Canada-spec. models

Mexico-spec. models

IFT
RLVDE1415-1661
14AHK
DENSO

Keys and doors/Keyless access with push-button start system

2-17

(126,1)

北米Model "A1350BE-A" EDITED: 2018/ 4/ 20

Immobilizer

The immobilizer system is designed to
prevent an unauthorized person from
starting the engine. Only keys registered
with your vehicle’s immobilizer system can
be used to operate your vehicle. If engine
start is attempted with an unregistered
access key fob or key, the engine will not
start. Even if the engine does start, it will
stop after a few seconds. This system,
however, is not a 100% anti-theft guaran-
tee.

CAUTION

Do not place the key under direct

sunlight or anywhere it may be-
come hot.

Do not get the key wet. If the key

gets wet, wipe it dry with a cloth
immediately.

Do not modify or remove the

system. If modified or removed,
the proper operation of the sys-
tem cannot be guaranteed.

NOTE

To protect your vehicle from theft,

please pay close attention to the follow-
ing security precautions:

– Never leave your vehicle unat-
tended with its keys inside.
– Before leaving your vehicle,
close all windows and the moon-
roof, and lock the doors, trunk
(sedan) and rear gate (5-door mod-
els).
– Do not leave spare keys or any
record of your key number in the
vehicle.

The vehicle has a maintenance-free

type immobilizer system.

Security indicator light

Refer to “Security indicator light” F3-30.

Key replacement

Your key number plate will be required if
you ever need a replacement key made.
Any new key must be registered for use
with your vehicle’s immobilizer system
before it can be used. The maximum
number of keys that can be registered for
use with one vehicle is as follows.
.

Four (models without “keyless access

with push-button start system”)

Seven (models with “keyless access

with push-button start system”)

One key that has already been registered
is required in order to register a new key.

NOTE

If you lose a key, the lost key’s ID code
still remains in the memory of the
vehicle’s immobilizer system. For se-
curity reasons, the lost key’s ID code
should be erased from the memory. To
erase the lost key’s ID code, all keys
that will be used are required.

For details about new key registration
and erasing the lost key’s ID code,
contact your SUBARU dealer.

Certification for immobilizer
system

For models with “keyless access

with push-button start system”:
Refer to “Certification for keyless access
with push-button start system” F2-17.

For models without “keyless access

with push-button start system”:

– U.S.-spec. models

FCC ID: Y8PFJ16-2

Keys and doors/Immobilizer

2-18

(127,1)

北米Model "A1350BE-A" EDITED: 2018/ 4/ 20

CAUTION

FCC WARNING
Changes or modifications not ex-
pressly approved by the party re-
sponsible for compliance could void
the user’s authority to operate the
equipment.

NOTE

– Canada-spec. models

– Mexico-spec. models

Keys and doors/Immobilizer

2-19

(128,1)

北米Model "A1350BE-A" EDITED: 2018/ 4/ 20

Remote keyless entry system

CAUTION

Do not expose the remote trans-

mitter to severe shocks, such as
those experienced as a result of
dropping or throwing.

Do not take the remote transmit-

ter apart except when replacing
the battery.

Do not get the remote transmitter

wet. If it gets wet, wipe it dry with
a cloth immediately.

When traveling in an airplane, do

not press the button of the re-
mote transmitter. If any button of
t h e r e m o t e t r a n s m i t t e r i s
pressed, radio waves are emitted
and may affect the operation of
the airplane. When carrying the
remote transmitter in a bag, take
measures to prevent the buttons
from being pressed accidentally.

Access key fob
1)

Lock/arm button

Unlock/disarm button

Trunk lid opener/rear gate unlock button

PANIC button

Transmitter
1)

Lock/arm button

Unlock/disarm button

Trunk lid opener/rear gate unlock button

PANIC button

The remote keyless entry system has the
following functions.
.

Locking and unlocking the doors (and

rear gate for 5-door models)
.

Unlocking the trunk lid (sedan) or rear

gate (5-door models)
.

Sounding a panic alarm

Arming and disarming the alarm sys-

tem. For detailed information, refer to
“Alarm system” F2-27.

The operable distance of the remote key-
less entry system is approximately 30 feet
(10 meters). However, this distance will

Keys and doors/Remote keyless entry system

2-20

(129,1)

北米Model "A1350BE-A" EDITED: 2018/ 4/ 20

vary depending on environmental condi-
tions. The system’s operable distance will
be shorter in areas near a facility or
electronic equipment emitting strong radio
waves such as a power plant, broadcast
station, TV tower, or remote controller of
home electronic appliances.

NOTE

For models with “keyless access

with push-button start system”, the
remote keyless entry system will not
be activated when the push-button
ignition switch is in any position other
than the “OFF” position.
.

For models without “keyless access

with push-button start system”, the
remote keyless entry system will not
be activated when the key is inserted in
the ignition switch.
.

The hazard warning flashers will

flash once or twice when the access
key fob/transmitter button is pressed in
the following cases.

– When locking the doors
– When unlocking the doors
– When opening the trunk lid (se-
dan)
– When unlocking the rear gate (5-
door models)

Operation of the hazard warning

flashers in the above cases can be set

to “On” or “Off” by a SUBARU dealer.
Consult your SUBARU dealer for de-
tails.
.

The setting of the remote trunk lid

opener function can be changed by a
SUBARU dealer. Consult your SUBARU
dealer for details. (sedan)

Locking the doors

Press the lock/arm button to lock all doors
and rear gate (5-door models). An electro-
nic chirp will sound once and the hazard
warning flashers will flash once.

If any of the doors (or the rear gate/trunk
lid) are not fully closed, the following will
occur to alert you that the doors (or the rear
gate/trunk lid) are not properly closed.
.

an electronic chirp sounds five times.

the hazard warning flashers flash five

times.

When you close the door, it will automati-
cally lock and then the following will occur.
.

an electronic chirp sounds once.

the hazard warning flashers flash once.

Unlocking the doors

Press the unlock/disarm button to unlock
the driver’s door. An electronic chirp will
sound twice and the hazard warning
flashers will flash twice. To unlock all doors
and the rear gate (5-door models), briefly
press the unlock/disarm button a second
time within 5 seconds.

NOTE

If the interval between the first and
second presses of the unlock/disarm
button (for unlocking of all of the doors
and the rear gate) is extremely short,
the system may not respond.

Opening the trunk lid
(sedan)

Press and hold the trunk lid opener button
to open the trunk lid. An electronic chirp
will sound twice and the hazard warning
flashers will flash twice.

Unlocking the rear gate
(5-door models)

Press the rear gate unlock button to unlock
the rear gate.
An electronic chirp will sound twice and the
hazard warning flashers will flash twice.

– CONTINUED –

Keys and doors/Remote keyless entry system

2-21

(130,1)

北米Model "A1350BE-A" EDITED: 2018/ 4/ 20

Vehicle finder function

Use this function to find your vehicle
parked among many vehicles in a large
parking lot. Provided you are within 30 feet
(10 meters) of the vehicle, pressing the
lock/arm button three times in a 5-second
period will cause your vehicle’s horn to
sound once and its hazard warning
flashers to flash three times.

NOTE

If the interval between presses is too
short when you press the lock/arm
button three times, the system may
not respond to the signals from the
remote transmitter.

Sounding a panic alarm

To activate the alarm, press the “PANIC”
button once.
The horn will sound and the hazard
warning flashers will flash.
To deactivate the panic alarm, press any
button on the remote transmitter. Unless a
button on the remote transmitter is
pressed, the alarm will be deactivated
after approximately 30 seconds.

Selecting audible signal op-
eration (models without
“keyless access with push-
button start system”)

Using an electronic chirp, the system will
give you an audible signal when the doors
lock and unlock. If desired, you may turn
the audible signal off.

Perform the following steps to deactivate
the audible signal. You can also use the
same steps to restore the function.
1. Sit in the driver’s seat and shut all
doors and the rear gate (5-door models).

2. Hold down the unlock side of the power
door locking switch.
3. While holding down the unlock side of
the power door locking switch, pull the key
out and reinsert it into the ignition switch at

least 6 times within 10 seconds after Step
2.
4. Open and close the driver’s door once
within 10 seconds after Step 3.
5. The hazard warning flashers flash 3
times to indicate completion of the setting.

Your SUBARU dealer can perform the
above procedure for you. Also, for models
with a combination meter display (color
LCD), the setting can be changed using
the display. For details, refer to “Vehicle
Setting” F3-40.

Replacing the battery

Refer to “Replacing key battery” F11-47.

Replacing lost transmitters

If you lose a transmitter or want to
purchase additional transmitters (up to
four can be programmed), your transmit-
ters should be reprogrammed for security
reasons. For details, contact your
SUBARU dealer and have the transmitters
programmed into the remote keyless entry
system.

Keys and doors/Remote keyless entry system

2-22

(131,1)

北米Model "A1350BE-A" EDITED: 2018/ 4/ 20

Certification for remote key-
less entry system

U.S.-spec. models

FCC ID: CWTB1G077
FCC ID: CWTD1G049

CAUTION

FCC WARNING

Changes or modifications not ex-
pressly approved by the party re-
sponsible for compliance could void
the user’s authority to operate the
equipment.

NOTE

Canada-spec. models

Mexico-spec. models

IFETEL RLVSUTB15-1814
SUBARU
MODEL: TB1G077

IFETEL RLVSUTD15-1815
SUBARU
MODEL: TD1G049

Keys and doors/Remote keyless entry system

2-23

(132,1)

北米Model "A1350BE-A" EDITED: 2018/ 4/ 20

Door locks

Locking and unlocking from
the outside

NOTE

If you unlock the driver’s door with a
key (including an emergency key) and
open the door while the alarm system is
armed, the alarm system is triggered
and the vehicle’s horn sounds. In this
case, perform any of the following
operations:

Models with “keyless access with

push-button start system”:

– Press any button on the access
key fob (except when the access
key fob battery is discharged).
– Press the push-button ignition
switch to “ACC”.
– Carry the access key fob and
perform either of the following pro-
cedures.

– Grip the front door handle
– Press the rear gate opener
button

Models without “keyless access

with push-button start system”:

– Press any button on the remote
transmitter (except when the trans-
mitter battery is discharged).

– Insert the key into the ignition
switch and turn the ignition switch
to “ON”.

For details about the alarm system,
refer to “Alarm system” F2-27.

How to lock and unlock the vehicle
by using the key

Rotate the key toward the front to lock.

Rotate the key toward the rear to unlock.

In this case, only the driver’s side door is
locked.

NOTE

Models with “keyless access with
push-button start system”:
The emergency key is directional. If the
key cannot be inserted, change the

direction that the grooved side is facing
and insert it again.

How to lock the vehicle without
using the key

To lock the door from outside without the
key, the following methods are available.

Locking using lock lever

Rotate the lock lever forward.

Close the door.

In this way, only the door that was operated
will be locked.

Keys and doors/Door locks

2-24

(133,1)

北米Model "A1350BE-A" EDITED: 2018/ 4/ 20

Locking using power door lock-
ing switch

Press the lock side of the power door
locking switch.*

Close the door.

*: For details about the power door locking

switch, refer to “How to operate the power
door locking switches” F2-25.

In this case, all closed doors and the rear
gate (5-door models) are locked at the
same time.

NOTE

Make sure that you do not leave the key
inside the vehicle when locking the
doors from the outside without the key.

Locking and unlocking from
the inside

How to use the lock lever

Rotate the lock lever rearward to unlock.

Rotate the lock lever forward to lock.

Always make sure that all doors and the
rear gate (5-door models) are closed
before starting to drive.

The red mark on the lock lever appears
when the door is unlocked.

WARNING

Keep all doors locked when you
drive, especially when small chil-
dren are in your vehicle.

Along with the proper use of seat-

belts and child restraints, locking
the doors reduces the chance of
being thrown out of the vehicle in an
accident.

It also helps prevent passengers
from falling out if a door is acciden-
tally opened, and intruders from
unexpectedly opening doors and
entering your vehicle.

How to operate the power door
locking switches

All doors and the rear gate (for 5-door
models) can be locked and unlocked using
the power door locking switches located at
the driver’s side and the front passenger’s
side doors.

– CONTINUED –

Keys and doors/Door locks

2-25

(134,1)

北米Model "A1350BE-A" EDITED: 2018/ 4/ 20

Example
1)

Press to lock

Press to unlock

NOTE

Make sure that you do not leave the key
inside the vehicle before locking the
doors from the outside using the power
door locking switches.

Key lock-in prevention func-
tion

Under the following conditions, all the
doors will not lock when the power door
locking switch is pushed with the driver
door open.
.

The key is still in the ignition switch

(models without “keyless access with
push-button start system”)
.

The ignition switch is in the “ACC” or

“ON” position (models with “keyless ac-
cess with push-button start system”)
.

With the driver’s door open, the doors

are automatically kept unlocked even if the
power door locking switch is pressed to the
lock position.

NOTE

When leaving the vehicle, make sure

you are holding the key before locking
the doors.
.

The factory setting (default setting)

for this function is set as “operational”.
This function’s operational/non-opera-
tional setting can be changed by a
SUBARU dealer. Contact a SUBARU
dealer for details.

Non-operation of key lock-in pre-
vention function

When the system is set so that it does not
operate, the doors are locked by the

following operation.
.

If the lock lever is turned to the front

(“LOCK”) position with the driver’s door
open and the driver’s door is then closed
with the lock lever in that position, the
driver’s door is locked.
.

If the spare key is used to lock the

driver’s door from the outside of the
vehicle, the door is locked.

Battery drainage prevention
function

If a door or the rear gate (5-door models) is
not completely closed, the interior lights
will remain illuminated as a result. How-
ever, several lights are automatically
turned off by the battery drainage preven-
tion function to prevent the battery from
discharging. The following interior lights
are affected by this function.

Item

Switch

position

Automatically turning

off

Map lights

DOOR

Approximately 20

minutes later

Dome light

DOOR

Approximately 20

minutes later

Ignition
switch light

—

Approximately 20

minutes later

Cargo area
light

DOOR

Approximately 20

minutes later

Keys and doors/Door locks

2-26

Subaru Impreza (2019 year). Instruction - part 8