SsangYong: Engine Euro 4. Manual - part 44

CHANGED BY

EFFECTIVE DATE

AFFECTED VIN

5

1491

DIAGNOSIS

D27DTP/D27DT (EU4)  SM - 2006.08

D27DTP/D27DT (EU4)

ENGINE

FUEL

I

N

T

AKE

EXHAUST

PRE-HEA

TING

LUB

COOLING

SWITCHABLE

ECU

DIAGNOSIS

1. Select “1] TROUBLE CODE” and press 

 on

“FUNCTION SELECTION” screen.

2. The [TROUBLE CODE] screen is displayed. It con-

tains the information for the trouble.

3. When selecting a trouble code, then

if you press 

 : Displays the sensor data for

the detected trouble (Freeze
Frame Mode).

if you press 

 : Displays the help tips for the

detected trouble.

2. SELECTION OF CHECKING

ITEMS FOR ENGINE D27DT/
D27DTP (POWER UP)

Check the Trouble Code

Ú

Ú

Ú

Ú

Ú Preceding Work: Perform the “Entering Diagnosis

Procedures”

ڟگګٻڍڒڋڃڞڎڤڄ

ڟگګٻڍڒڋڃڞڎڤڄ

ڨڤڮڞڠڧڧڜکڠڪڰڮ

ڨڤڮڞڠڧڧڜکڠڪڰڮ

ڞڎڤ

ڞڎڤ

ڟگګٻڍڒڋڃڞڎڤڄ

ڟگګٻڍڒڋڃڞڎڤڄ

ڞڈګڌڐڎڏډٻپڍٻڣۀڼۏۀۍٻڟۍۄۑۀۍٻڪۋۀۉٻڞۄۍھېۄۏ

ڞڈګڌڐڎڏډٻپڍٻڣۀڼۏۀۍٻڟۍۄۑۀۍٻڪۋۀۉٻڞۄۍھېۄۏ

ڞڈګڌڐڎڋډٻپڌٻڣۀڼۏۀۍٻڟۍۄۑۀۍٻڪۋۀۉٻڞۄۍھېۄۏ

ڞڈګڌڐڎڋډٻپڌٻڣۀڼۏۀۍٻڟۍۄۑۀۍٻڪۋۀۉٻڞۄۍھېۄۏ
ڣڈګڋڌڋړډٻڝۊۊێۏٻګۍۀێێېۍۀٻڮۀۉێۊۍٻڪۋۀۉ

ڣڈګڋڌڋړډٻڝۊۊێۏٻګۍۀێێېۍۀٻڮۀۉێۊۍٻڪۋۀۉ

• If there is not any fault, “No Diagnostic Trouble

Codes” message appears.

NOTE

CHANGED BY

EFFECTIVE DATE

AFFECTED VIN

6

1491

DIAGNOSIS

D27DTP/D27DT (EU4)  SM - 2006.08

D27DTP/D27DT (EU4)

1. Select “2] DATA LIST” and press 

 on “FUNC-

TION SELECTION” screen.

2. The screen shows all the sensor data.

Sensor Data Check

Ú

Ú

Ú

Ú

Ú Preceding Work: Perform the “Entering Diagnosis

Procedures”

ڟگګٻڍڒڋڃڞڎڤڄ

ڟگګٻڍڒڋڃڞڎڤڄ

ڨڤڮڞڠڧڧڜکڠڪڰڮ

ڨڤڮڞڠڧڧڜکڠڪڰڮ

ڞڎڤ

ڞڎڤ

3. Select the items you want to see and press 

key to freeze them.

• You can freeze up to 5 items (*: selected items).

NOTE

CHANGED BY

EFFECTIVE DATE

AFFECTED VIN

7

1491

DIAGNOSIS

D27DTP/D27DT (EU4)  SM - 2006.08

D27DTP/D27DT (EU4)

ENGINE

FUEL

I

N

T

AKE

EXHAUST

PRE-HEA

TING

LUB

COOLING

SWITCHABLE

ECU

DIAGNOSIS

ڟگګٻڍڒڋڃڞڎڤڄ

ڟگګٻڍڒڋڃڞڎڤڄ

ڭڠڳگڪکٻڠڞڰٻڟگګٻڍڒڋڃڞڎڤڄ

ڭڠڳگڪکٻڠڞڰٻڟگګٻڍڒڋڃڞڎڤڄ

ڜڞگڰڜگڪڭٻڮڠڧڠڞگڤڪک

ڜڞگڰڜگڪڭٻڮڠڧڠڞگڤڪک

ڋڌڸٻڠڢڭٻڱڜڧڱڠ

ڋڌڸٻڠڢڭٻڱڜڧڱڠ

ڋڍڸٻگڈڝڪڟڴڃڡڧڜګڄ

ڋڍڸٻگڈڝڪڟڴڃڡڧڜګڄ
ڋڎڸٻڢڧڪڲٻڰکڤگ

ڋڎڸٻڢڧڪڲٻڰکڤگ
ڋڏڸٻڤڨڱٻڱڜڧڱڠ

ڋڏڸٻڤڨڱٻڱڜڧڱڠ
ڋڐڸٻگڰڭڝڪٻڨڪڟڰڧډ

ڋڐڸٻگڰڭڝڪٻڨڪڟڰڧډ
ڋڑڸٻڡڜکٻپڌ

ڋڑڸٻڡڜکٻپڌ
ڋڒڸٻڡڜکٻپڌڊپڍ

ڋڒڸٻڡڜکٻپڌڊپڍ
ڋړڸٻڡڜکڃګڲڨڄ

ڋړڸٻڡڜکڃګڲڨڄ
ڋڔڸٻګڪڲڠڭٻڭڠڧڜڴ

ڋڔڸٻګڪڲڠڭٻڭڠڧڜڴ
ڌڋڸٻڠکڢٻڞڣڠڞڦٻڧڜڨګ

ڌڋڸٻڠکڢٻڞڣڠڞڦٻڧڜڨګ
ڌڌڸٻڢڧڪڲٻګڧڰڢٻڧڜڨګ

ڌڌڸٻڢڧڪڲٻګڧڰڢٻڧڜڨګ

ڌڍڸٻڤڨڨڪډڧڜڨګ

ڌڍڸٻڤڨڨڪډڧڜڨګ
ڌڎڸٻڜڊڞٻڭڠڧڜڴ

ڌڎڸٻڜڊڞٻڭڠڧڜڴ
ڌڏڸٻګگڞٻڭڠڧڜڴڃپڍڄ

ڌڏڸٻګگڞٻڭڠڧڜڴڃپڍڄ
ڌڐڸٻګگڞٻڭڠڧڜڴڃپڌڄ

ڌڐڸٻګگڞٻڭڠڧڜڴڃپڌڄ
ڌڑڸٻڡڰڠڧٻڡڤڧڧگڠڭ

ڌڑڸٻڡڰڠڧٻڡڤڧڧگڠڭ
ڌڒڸٻڤکڥڠڞگڪڭٻپڌ

ڌڒڸٻڤکڥڠڞگڪڭٻپڌ
ڌړڸٻڤکڥڠڞگڪڭٻپڍ

ڌړڸٻڤکڥڠڞگڪڭٻپڍ
ڌڔڸٻڤکڥڠڞگڪڭٻپڎ

ڌڔڸٻڤکڥڠڞگڪڭٻپڎ
ڍڋڸٻڤکڥڠڞگڪڭٻپڏ

ڍڋڸٻڤکڥڠڞگڪڭٻپڏ
ڍڌڸٻڤکڥڠڞگڪڭٻپڐ

ڍڌڸٻڤکڥڠڞگڪڭٻپڐ

ڟگګٻڍڒڋڃڞڎڤڄ

ڟگګٻڍڒڋڃڞڎڤڄ

ڨڤڮڞڠڧڧڜکڠڪڰڮ

ڨڤڮڞڠڧڧڜکڠڪڰڮ

ڞڎڤ

ڞڎڤ

1. Select “3] ACTUATOR CHECK” and press 

 on

“FUNCTION SELECTION” screen.

2. The screen shows 21 items. Select the item you

want to see and press 

.

3. For example, if you select “03] GLOW UNIT” item

and press 

 , the screen as shown in figure is

displayed.

Actuator Check

Ú

Ú

Ú

Ú

Ú Preceding Work: Perform the “Entering Diagnosis

Procedures”

• This section is subject to change or update from

time to time so it is mainly described for the diag-
nostic progress. For actual display items, refer to
SCAN-100 screens.

NOTICE

CHANGED BY

EFFECTIVE DATE

AFFECTED VIN

8

1491

DIAGNOSIS

D27DTP/D27DT (EU4)  SM - 2006.08

D27DTP/D27DT (EU4)

4. If you want to operate the glow plug relay, press

“

” key. The “CHECKING THE CIRCUIT

(WAIT...)” message appears and the glow plug
warning light in the instrument cluster comes on.

5. If the system operates properly, Scan-100 displays

“GOOD”.

ڟگګٻڍڒڋڃڞڎڤڄ

ڟگګٻڍڒڋڃڞڎڤڄ

ڙڙٻڞڣڠڞڦڤکڢٻگڣڠٻڞڤڭڞڰڤگڃڲڜڤگډډډڄٻڗڗ

ڙڙٻڞڣڠڞڦڤکڢٻگڣڠٻڞڤڭڞڰڤگڃڲڜڤگډډډڄٻڗڗ

ڟگګٻڍڒڋڃڞڎڤڄ

ڟگګٻڍڒڋڃڞڎڤڄ

ڰکڤگ

ڰکڤگ

6. If you want to stop the operation, press “

” key.