SsangYong Musso. Manual - part 321

1F1-42  M162 ENGINE CONTROLS

Pin No.

Description

Pedal potentiometer 1 ground

Pedal potentiometer 1 supply

Fuel pump relay

Tank purge valve

Engine fan

-

CAN-Low

CAN-High

-

-

-

-

Clutch switch

Air conditioning

Electronic traction signal(ABD)

-

Pedal potentiometer 1 signal

Pedal potentiometer 2 signal

Brake light switch

Pedal potentiometer 2 ground

Pedal potentiometer 2 supply

Cruise accelerate/Set

Cruise resume

Cruise decelerate/Set

Cruise safety contact switch

-

Cruise off switch

Diagnostics(K-line)

Vehicle speed signal

Engine speed signal

31

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

49

50

51

52

53

54

55

56

57

58

59

60

GND

SP1+5V

KP

TEV

ML

-

CAN L

CAN H

-

-

-

-

KPL

KLIMA

ETS

-

SP1S

SP2S

BLS

GND

SP2+2.5V

S+B

WA

S-B

KSK

-

AUS

DIAG

V-SIG

TN-SIG

z
z
z
z
z

-

z
z

-

-

-

-

{

z

{

-

z
z

{

z
z

{
{
{
{

-

{

z
z
z

z
z
z
z
z

-

z
z

-

-

-

-

{

z

{

-

z
z

{

z
z

{
{
{
{

-

{

z
z
z

Remarks

Abbreviation

E32 ENG,

5speed M/T

E32 ENG,

4speed A/T

(BTRA)

M162 ENGINE CONTROLS  1F1-43

Pin No.

61

62

63

64

65

66

67

68

69

70

71

72

73

74

75

76

77

78

79

80

81

82

83

84

85

86

87

88

89

90

Description

Injector-cylinder 2

Injector-cylinder 4

Injector-cylinder 1

Injector-cylinder 6

Injector-cylinder 5

Injector-cylinder 3

E-GAS motor plus

E-GAS motor minus

Power ground TM.31

Ignition coil cylinder 1+6

Ignition coil cylinder 2+5

Ignition coil cylinder 3+4

Camshaft control

-

-

-

-

Engine coolant temperature

Temperature ground

Intake air temperature

Hot film air mass signal

-

-

E-GAS potentiometer ground

E-GAS potentiometer 2 signal

-

E-GAS potentiometer 1 signal

-

-

-

EV5

EV6

EV1

EV4

EV2

EV3

M+

M-

TM.31

ZSC16

ZSA25

ZSB34

NWS

-

-

-

-

MT

GND

LT

HFM

-

-

GND

IP2S

-

IP1S

-

-

-

z
z
z
z
z
z
z
z
z
z
z
z
z

-

-

-

-

z
z
z
z

-

-

z
z

-

z

-

-

-

z
z
z
z
z
z
z
z
z
z
z
z
z

-

-

-

-

z
z
z
z

-

-

z
z

-

z

-

-

-

Remarks

Abbreviation

E32 ENG,

5speed M/T

E32 ENG,

4speed A/T

(BTRA)

1F1-44  M162 ENGINE CONTROLS

Pin No.

Description

-

-

-

-

-

-

Intake manifold resonance flap

-

Crankshaft sensor ground

Crankshaft sensor signal

-

-

-

Camshaft sensor ground

Hot film air mass ground

Camshaft sensor signal

-

Hot film air mass supply

-

-

-

E-GAS potentiometer supply

-

Knock sensor 2 ground

Knock sensor 2 signal

-

Knock sensor 1 ground

Knock sensor 1 signal

-

-

91

92

93

94

95

96

97

98

99

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

-

-

-

-

-

-

SRV

-

KW-

KW+

-

-

-

NOWE-

GND

NOWE+

-

V-REF.HFM

-

-

-

V-REF.DK

-

GND

KS2

-

GND

KS1

-

-

-

-

-

-

-

-

z

-

z
z

-

-

-

z
z
z

-

z

-

-

-

z

-

z
z

-

z
z

-

-

-

-

-

-

-

-

z

-

z
z

-

-

-

z
z
z

-

z

-

-

-

z

-

z
z

-

z
z

-

-

Remarks

Abbreviation

E32 ENG,

5speed M/T

E32 ENG,

4speed A/T

(BTRA)

M162 ENGINE CONTROLS  1F1-45

Removal & Installation Procedure

z

z

z

z

z

when removing the ECU only

1. Turn the ignition switch to "OFF" position.

2. Disconnect the negative battery cable.

3. Disconnect the couplings from ECU.

4. Unscrew the left and right bolt (3) on bolt (1) and auxiliarly

bracket and remove the auxiliarly bracket from the bracket
assembly (2).

Installation Notice

5. Unscrew the four bolts (5) and disconnect the ECU (6) from

the bracket assenbly.

Installation Notice

6. Installation should follow the removal procedure in the

reverse order.

Tightening Torque

6 - 8 Nm

5 - 7 Nm

(1)

(3)

Tightening  Torque

5 - 7 Nm

8. Unscrew the bolts (5) and disconnect the ECU (6) from  the

bracket assenbly.

Installation Notice

z

z

z

z

z

When Removing the ECU with ABS or ABS/ASR Unit

1. Turn the ignition switch to "OFF" position.

2. Disconnect the negative battery cable.

3. Disconnect the couplings from ECU.

4. Disconnect the coupling from ABS or ABS/ASR unit.

5. Unscrew the bolt (1) and the left and right flange nuts.

6. Remove the ECU with ABS or ABS/ASR unit assembly.

7. Unscrew the left and right bolt (3) on the auxiliary bracket

and remove the auxiliary bracket from the bracket assembly.

Installation Notice

Tightening  Torque

6 - 8 Nm

Tightening  Torque

5 - 7 Nm

Tightening  Torque

5 - 7 Nm

9. Installation should follow the removal procedure in the

reverse order.