Opel Zafira (2020 year). Manual in english - page 7

 

  Index      Manuals     Opel Zafira (2020 year). Manual in english

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

 

 

 

Content      ..     5      6      7      8     ..

 

 

 

Opel Zafira (2020 year). Manual in english - page 7

 

 

Lighting
137
Illustration shows rear courtesy lights.
This function can be activated or
Lighting features
deactivated in the vehicle
personalisation 3 124.
Sunvisor lights
Centre console lighting
The following lights will additionally
Illuminates when the cover is opened.
A spotlight integrated in the overhead
switch on when the driver's door is
console illuminates the centre
opened:
console when headlights are
switched off.
● illumination of some switches
The brightness can be adjusted in the
● Driver Information Centre
vehicle personalisation 3 124.
Exit lighting
Entry lighting
The following lights are switched on if
the key is removed from the ignition
Welcome lighting
switch:
Some or all of the following lights are
● interior lights
switched on for a short time by
● instrument panel light
unlocking the vehicle with the radio
They will switch off automatically after
remote control:
a delay. This function works only in
● headlights
the dark.
● tail lights
Path lighting
● interior lights
The number of activated lights
Headlights, tail lights and number
depends on the surrounding light
plate lights illuminate the surrounding
conditions.
area for an adjustable time after
leaving the vehicle.
The lighting switches off immediately
when the ignition is switched on.
Starting off 3 19.
138
Lighting
Manual path lighting
Automatic path lighting
Press
D
a second time to switch off
Path lighting is activated, when the
peripheral lighting.
ignition is switched off and the driver's
door is opened.
Battery discharge protection
This function can be activated or
To prevent discharge of the vehicle
deactivated in the vehicle
battery when the ignition is switched
personalisation 3 124.
off, some interior lights are switched
Info Display 3 120.
off automatically after some time.
Vehicle locator lighting
This function allows to locate the
vehicle, e.g., in weak lighting
conditions using the remote control.
To switch on the manual path lighting,
The headlights come on and the turn
switch off the ignition, open the
lights flash for 10 seconds.
driver's door and pull the indicator
Press N on the remote control.
lever.
The vehicle must be locked more than
If the driver's door is not closed, the
5 seconds.
lights switch off after several seconds.
To switch off the manual path lighting
pull the lever again while the driver's
Peripheral lighting
door is open.
Peripheral lighting allows you to
The duration of the path lighting can
switch on the position lights, low
be set in the vehicle personalisation
beam and number plate lighting using
3 124.
the remote control.
Info Display 3 120.
Press
D
on the remote control to
switch on peripheral lighting.
Climate control
139
Heated seats ß 3 52.
Climate control
Climate control systems
Temperature
Heating and ventilation
Adjust the temperature by turning ñ
system
Climate control systems
139
to the desired temperature.
Heating and ventilation system 139
HI
: warm
Air conditioning system
141
LO : cold
Electronic climate control
system
143
Heating will not be fully effective until
Parking heater
147
the engine has reached normal
Air vents
149
operating temperature.
Adjustable air vents
149
Air distribution
Fixed air vents
150
Glovebox cooler
150
w : to windscreen and front door
Maintenance
150
windows
Air intake
150
x : to head area via adjustable air
Air conditioning regular
vents
operation
151
y : to foot well and windscreen
Controls for:
Service
151
● temperature ñ
All combinations are possible.
● air distribution w, x and y
Fan speed
● fan speed ý
● air recirculation q
● heated rear window è or heated
exterior mirrors
m
Heated rear window è 3 44.
Heated exterior mirrors
m
3 40.
140
Climate control
Adjust the air flow by turning ý to the
Demisting and defrosting
9 Warning
desired speed.
clockwise
: increase
The exchange of fresh air is
anticklockwise : decrease
reduced in air recirculation mode.
In operation without cooling the air
Air recirculation system q
humidity increases, so the
windows may mist up from inside.
The quality of the passenger
compartment air deteriorates,
which may cause the vehicle
occupants to feel drowsy.
In warm and very humid ambient air
conditions, the windscreen may mist
● Press w: the air distribution is
up from outside when cold air is
directed towards the windscreen.
directed towards it. If windscreen
mists up from outside, activate
● Set temperature controller ñ to
windscreen wiper and deactivate w.
warmest level.
● Set fan speed ý to highest level.
Press q to activate air recirculation
mode. The LED in the button
● Switch on heated rear window
illuminates to indicate activation.
and exterior mirrors è or switch
on heated exterior mirrors
m
Press q again to deactivate air
recirculation mode.
● Switch on heated
windscreen ,.
● Open side air vents as required
and direct them towards the door
windows.
Heated rear window è 3 44.
Climate control
141
Heated exterior mirrors
m
3 40.
Heated exterior mirrors
m
3 40.
Cooling A/C
Heated windscreen
9
3 45.
Temperature ñ
Adjust the temperature by turning ñ
Air conditioning system
to the desired temperature.
HI
: warm
LO : cold
Heating will not be fully effective until
the engine has reached normal
operating temperature.
Air distribution w, x, y
w : to windscreen and front door
Press A/C to switch on cooling. The
windows
LED in the button illuminates to
x : to head area via adjustable air
indicate activation. Cooling is only
vents
functional when the engine is running
y : to foot well
Controls for:
and fan is switched on.
● temperature ñ
All combinations are possible.
Press A/C again to switch off cooling.
● air distribution w, x and y
The air conditioning system cools and
Fan speed ý
● fan speed ý
dehumidifies (dries) as soon as the
Adjust the air flow by turning ý to the
outside temperature is slightly above
● cooling A/C
desired speed.
the freezing point. Therefore,
● air recirculation q
condensation may form and drip from
clockwise
: increase
● heated rear window è or heated
anticlockwise : decrease
under the vehicle.
exterior mirrors
m
If no cooling or drying is required,
Heated rear window è 3 44.
switch off the cooling system for fuel
saving reasons.
142
Climate control
Activated cooling may inhibit
● Switch on cooling A/C.
windows may mist up from inside.
Autostops. Stop-start system 3 157.
The quality of the passenger
● Press q for air recirculation
compartment air deteriorates,
system on.
Air recirculation system q
which may cause the vehicle
● Press x for air distribution.
occupants to feel drowsy.
● Set temperature control ñ to
coldest level.
In warm and very humid ambient air
conditions, the windscreen may mist
● Set fan speed ý to highest level.
up from outside when cold air is
● Open all vents.
directed towards it. If windscreen
mists up from outside, activate
Demisting and defrosting the
windscreen wiper and deactivate w.
windows
Maximum cooling
Press q to activate air recirculation
mode. The LED in the button
illuminates to indicate activation.
Press q again to deactivate air
recirculation mode.
9 Warning
The exchange of fresh air is
● Set fan speed ý to highest level.
reduced in air recirculation mode.
● Set temperature controller ñ to
In operation without cooling the air
Briefly open the windows so that hot
warmest level.
humidity increases, so the
air can disperse quickly.
Climate control
143
● Switch on cooling A/C, if
Electronic climate control
required.
system
● Switch on heated rear window
The dual zone climate control allows
è or heated exterior mirrors
different temperatures for driver side
m
and front passenger side.
● Switch on heated windscreen
In automatic mode, temperature, fan
demisting and defrosting
h
9
speed and air distribution are
● Open side air vents as required
cooling A/C
regulated automatically.
and direct them towards the door
automatic mode AUTO
windows.
dual zone temperature
Note
synchronisation MONO
If the settings for demisting and
heated rear window è or heated
defrosting are selected, an
exterior mirrors
m
Autostop may be inhibited.
fan speed
r
s
If the settings for demisting and
Heated rear window è 3 44.
defrosting are selected while the
engine is in an Autostop, the engine
Heated exterior mirrors
m
3 40.
will restart automatically. Stop-start
Activated functions are indicated by
system 3 157.
the LED in the respective control.
Heated rear window è 3 44.
The electronic climate control system
Heated exterior mirrors
m
3 40.
Controls for:
is only fully operational when the
engine is running.
Heated windscreen
9
3 45.
● manual air recirculation q
Stop-start system 3 157.
● air distribution w
● rocker switch for adjusting the
temperature on driver side and
front passenger side
144
Climate control
Automatic mode AUTO
● Air conditioning must be
Fan speed
rs
activated for optimal cooling and
demisting. Press A/C to switch on
air conditioning. The LED in the
button indicates activation.
● Set the preselected
temperatures for driver and front
passenger using the left and right
rotary ring. Recommended
temperature is 22 °C.
Press successively AUTO to select
the desired automatic settings:
● Soft Auto for a soft and silent air
distribution.
Basic setting for maximum comfort:
Press
r
to increase or
s
to
● Auto for thermal comfort and
decrease the air flow.
● Press AUTO, the air distribution
silent air distribution.
and fan speed are regulated
To return to automatic mode, press
automatically.
● Auto Fast for a dynamic and
AUTO.
efficient air distribution.
● Open all air vents to allow
optimised air distribution in
Manual settings
automatic mode.
Climate control system settings can
be changed by activating the
following functions:
Climate control
145
Air distribution w
To return to automatic air distribution,
Note
press AUTO.
If A/C is switched on, reducing the
set cabin temperature can cause the
Temperature preselection
engine to restart from an Autostop or
inhibit an Autostop.
Stop-start system 3 157.
Dual zone temperature
synchronisation MONO
Press MONO to link passenger side
temperature setting to the driver side /
Set the preselected temperatures
to remove the linking of the
separately for the driver and the front
passenger side temperature setting
passenger to the desired value using
to the driver side. The passenger side
Press w sucessively until the desired
the left and right switch for
temperature setting is linked to the
direction of the air distribution is
adjustusting the temperature.
driver side if the LED in the button
displayed:
Recommended temperature is 22 °C.
MONO is not illuminated.
t : to windscreen and front door
Temperature is indicated in the
windows
display beside the switches for
u : to head area and rear seats via
adjusting the temperature.
adjustable air vents
If the minimum temperature Lo is set,
v : to front and rear foot well
the climate control system runs at
w : to windscreen and front door
maximum cooling, if cooling A/C is
windows, to head area and rear
switched on.
seats via adjustable air vents, to
If the maximum temperature Hi is set,
front and rear foot well
the climate control system runs at
maximum heating.
Combinations of different air
distribution options can be select by
pressing w sucessively.
146
Climate control
Air conditioning A/C
Manual air recirculation q
compartment air deteriorates,
which may cause the occupants to
feel drowsy.
In warm and very humid ambient air
conditions, the windscreen may mist
up from outside, when cold air is
directed towards it. If windscreen
mists up from outside, activate
windscreen wiper and deactivate w.
Demisting and defrosting the
windows
h
Press A/C to switch on cooling.
Press q to activate the air
Cooling is only functional when the
recirculation mode. q is shown in the
engine is running and climate control
display to indicate activation.
fan is switched on.
Press q again to deactivate
Press A/C again to switch off cooling.
recirculation mode.
The air conditioning system cools and
dehumidifies (dries) when outside
9 Warning
temperature is above a specific level.
Therefore condensation may form
The exchange of fresh air is
and drip from under the vehicle.
reduced in air recirculation mode.
In operation without cooling, the
If no cooling or drying is required,
air humidity increases, so the
switch off the cooling system for fuel
● Press
h. The LED in the button
windows may mist up from inside.
saving reasons.
illuminates to indicate activation.
The quality of the passenger
Climate control
147
● Air conditioning and automatic
Deactivation of electronic climate
● LED illuminates: A timer has
mode are automatically switched
control system
been set.
on. The LED in the button A/C
Press
s
subsequently until the
● LED flashes: The system is
illuminates, AUTO is shown in the
electronic climate control system is
operating.
display.
deactivated.
The LED is extinguished at the end of
● Temperature and air distribution
the heating operation or when the
are set automatically and the fan
Parking heater
parking heater is stopped using the
runs at high speed.
remote control.
The parking heater allows to heat the
● Switch on heated rear window
vehicle's interior and to ventilate the
The parking heater can be
è.
vehicle's interior with ambient air.
programmed using the Infotainment
● Switch on heated windscreen
system. Additionally, the parking
9
heater can be switched on and off
using a remote control.
● To return to previous mode,
press
h
again.
Radio (Infotainment system)
Note
Press MENU to open the menu page.
If
h
is pressed while the engine is
running, an Autostop will be inhibited
Press Heating or Ventilation.
until
h
is pressed again.
Press
H
or
I
to select the desired
If
h
is pressed while the engine is
timer. Confirm with OK.
in an Autostop, the engine will restart
Set the required time of the timer:
automatically.
Press 7 or 8 to set the desired
value. Confirm with OK.
Heated rear window è 3 44.
The operating status of the parking
To set the timer, press
H
or
I
to
Heated exterior mirrors
m
3 40.
heater is shown by an indicator with
select OK on the display. Confirm with
Heated windscreen
9
3 45.
an LED.
OK.
Stop-start system 3 157.
148
Climate control
Multimedia / Multimedia Navi
Press d.
Press Temperature conditioning.
Activate Temperature conditioning by
pressing ON.
Press Settings.
Select Heating or Ventilation.
Press Time 1 or Time 2 to select the
desired timer.
Define the time of the selected timer.
Press 6 to save the settings and set
Press i.
1. Remove the cap of the remote
control by unscrewing it with a
the timer.
Replacing the battery in the remote
coin and remove the battery
Parking heater via remote control
control
2. Replace battery with a battery of
If the indicator light of the remote
the same type. Pay attention to
The parking heater can be switched
control turns yellow, the charging
the installation position.
on using a remote control.
status of the battery is weak. If the
3. Screw the cap in its place .
indicator light does not illuminated
anymore, the battery is discharged
and has to be replaced.
Climate control
149
Outer air vents in the instrument
Rear air vents in the ceiling
Air vents
panel
Adjustable air vents
Air vents in the instrument panel
To activate the distribution of
Direct the flow of air by tilting and
climatised / heated air via the rear air
swivelling the slats.
vents, press
E
To close the vent, swivel the slats
Direct the flow of air by tilting and
outwards.
swivelling the slats.
At least two air vents must be open
To close the vent, swivel the slats
while cooling is on.
inwards.
9 Warning
Do not attach any objects to the
slats of the air vents. Risk of
damage and injury in case of an
accident.
150
Climate control
Direct the flow of air by tilting and
Turn the slider up or down in order to
Maintenance
swivelling the slats.
enable or disable glovebox cooling.
Adjust the air flow to select the
Air intake
desired speed.
Fixed air vents
Additional air vents are located
beneath the windscreen, the door
windows and in the foot wells.
Glovebox cooler
The air conditioning system draws
cooled air into the glovebox through a
noozle.
The air intake in front of the
windscreen in the engine
compartment must be kept clear to
allow air intake. Remove any leaves,
dirt or snow.
Climate control
151
Air conditioning regular
operation
In order to ensure continuously
efficient performance, cooling must
be operated for a few minutes once a
month, irrespective of the weather
and time of year. Operation with
cooling is not possible when the
outside temperature is too low.
Service
For optimal cooling performance, it is
recommended to annually check the
climate control system, starting
three years after initial vehicle
registration, including:
● functionality and pressure test
● heating functionality
● leakage check
● check of drive belts
● cleaning of condenser and
evaporator drainage
● performance check
152
Driving and operating
Trailer towing
206
Brakes
169
Driving and
Towing equipment
207
Antilock brake system
169
Trailer stability assist
210
operating
Parking brake
170
Brake assist
171
Hill start assist
171
Ride control systems
171
Driving hints
153
Electronic Stability Control and
Control of the vehicle
153
Traction Control system
171
Steering
153
Selective ride control
172
Starting and operating
153
Driver assistance systems
174
New vehicle running-in
153
Cruise control
174
Ignition switch positions
153
Speed limiter
177
Power button
154
Adaptive cruise control
180
Starting the engine
155
Forward collision alert
187
Overrun cut-off
157
Active emergency braking
188
Stop-start system
157
Front pedestrian protection
191
Parking
160
Parking assist
192
Engine exhaust
161
Side blind spot alert
194
Exhaust filter
161
Panoramic view system
196
Catalytic converter
161
Rear view camera
199
AdBlue
162
Lane departure warning
200
Automatic transmission
165
Driver alert
201
Transmission display
166
Fuel
203
Gear selection
166
Fuel for diesel engines
203
Manual mode
167
Refuelling
204
Electronic driving programmes 168
Trailer hitch
205
Fault
168
General information
205
Manual transmission
168
Driving characteristics and
towing tips
205
Driving and operating
153
Driving hints
Steering
Starting and operating
If power steering assist is lost
Control of the vehicle
because the engine stops or due to a
New vehicle running-in
system malfunction, the vehicle can
Do not brake unnecessarily hard for
Never coast with engine not
be steered but may require increased
the first few journeys.
running
effort.
During the first drive, smoke may
Many systems will not function in this
occur because of wax and oil
situation (e.g. brake servo unit, power
evaporating off the exhaust system.
steering). Driving in this manner is a
Park the vehicle in the open for a
danger to yourself and others.
while after the first drive and avoid
All systems function during an
inhaling the fumes.
Autostop.
During the running-in period, fuel and
Stop-start system 3 157.
engine oil consumption may be
higher.
Pedals
Additionally, the cleaning process of
the exhaust filter may take place more
To ensure the pedal travel is
often.
uninhibited, there must be no mats in
the area of the pedals.
Exhaust filter 3 161.
Use only floor mats, which fit properly
and are fixed by the retainers on the
Ignition switch positions
driver side.
Turn key:
154
Driving and operating
Ignition on power mode without
9 Danger
starting the engine
Press Start/Stop without operating
Never remove the key from
clutch or brake pedal. Control
ignition switch during driving as
indicators illuminate and most
this will cause steering wheel lock.
electrical functions are operable.
Engine and ignition off
Power button
Press Start/Stop briefly in each mode
or when engine is running and vehicle
is stationary. Some functions remain
active until driver's door is opened,
provided the ignition was on
0
:
ignition off: some functions
previously.
remain active until key is
Emergency shut off during driving
removed or driver's door is
Press Start/Stop for about 3 seconds
opened, provided the ignition was
3 155. Steering wheel locks as soon
on previously
as vehicle is stationary.
1
:
ignition on power mode: ignition
is on, diesel engine is preheating,
Steering wheel lock
control indicators illuminate and
The steering wheel lock activates
most electrical functions are
The electronic key must be inside the
automatically when:
operable
vehicle.
2
:
engine start: release key after
● The vehicle is stationary.
engine has been started
Engine start
● The ignition has been switched
Operate the clutch pedal (manual
off.
Steering wheel lock
transmission), the brake pedal and
To release steering wheel lock, open
press Start/Stop.
Remove key from ignition switch and
and close driver's door and switch the
turn steering wheel until it engages.
ignition on power mode or start the
engine directly.
Driving and operating
155
Hold the electronic key with buttons
Starting the engine
9 Warning
outside at the marking on the steering
column cover as shown in the
Vehicles with ignition switch
If the vehicle battery is discharged,
illustration.
the vehicle must not be towed,
Operate the clutch pedal (manual
tow-started or jump-started as the
transmission), the brake pedal and
steering wheel lock cannot be
press Start/Stop.
disengaged.
This option is intended for
Operation on vehicles with
emergencies only. Replace the
electronic key system in case of
electronic key battery as soon as
possible 3 24.
failure
For unlocking or locking the doors,
If either the electronic key fails or the
see fault in radio remote control unit
battery of the electronic key is weak,
or electronic key system 3 25.
a message may be displayed in the
Driver Information Centre.
Turn key to position 1 to release the
steering wheel lock.
Manual transmission: operate clutch
and brake pedal.
Automatic transmission: operate
brake pedal and move selector lever
to P or N.
Do not operate accelerator pedal.
Diesel engines: wait until control
indicator
z
extinguishes.
156
Driving and operating
Turn key briefly to position 2 and
Manual transmission: operate
Emergency shut off during driving
release after engine has been
clutch and brake pedal.
If the engine needs to be switched off
started.
Automatic transmission: operate
during driving in case of emergency,
Manual transmission: during an
brake pedal and move selector
press Start/Stop for 5 seconds.
Autostop, the engine can be started
lever to P or N.
by depressing the clutch pedal
Do not operate accelerator pedal.
9 Danger
3 157.
Press Start/Stop button.
Automatic transmission: during an
Switching off the engine during
Release button after starting
Autostop, the engine can be started
driving may cause loss of power
procedure begins. Diesel engine
by releasing the brake pedal 3 157.
support for brake and steering
starts after control indicator
z
systems. Assistance systems and
Vehicles with power button
for preheating extinguishes.
airbag systems are disabled.
Before restarting or to switch off
Lighting and brake lights will
the engine when vehicle is
extinguish. Therefore power down
stationary, press Start/Stop once
the engine and ignition while
more briefly.
driving only when required in case
To start the engine during an
of emergency.
Autostop:
● Manual transmission: during an
Autostop, the engine can be
started by depressing the clutch
pedal 3 157.
● Automatic transmission: during
an Autostop, the engine can be
started by releasing the brake
pedal 3 157.
Driving and operating
157
Starting the vehicle at low
Depending on driving conditions, the
With touchscreen
temperatures
overrun cut-off may be deactivated.
The system can be activated in the
vehicle personalisation 3 124. If the
Starting the engine without additional
stop-start system is temporarily not
Stop-start system
heaters is possible down to -25 °С for
available, the control indicator D
diesel engines and -30 °C for petrol
The stop-start system helps to save
flashes for a few seconds.
engines. Required is an engine oil
fuel and to reduce the exhaust
with the correct viscosity, the correct
emissions. When conditions allow, it
Deactivation
fuel, performed services and a
switches off the engine as soon as the
Without touchscreen
sufficiently charged vehicle battery.
vehicle is at a low speed or at a
With temperatures below -30 °C the
standstill, e.g. at a traffic light or in a
automatic transmission requires a
traffic jam.
warming phase of approx. 5 minutes.
The selector lever must be in position
Activation
P.
The stop-start system is available as
soon as the engine is started, the
Turbo engine warm-up
vehicle starts-off and the conditions
Upon start-up, engine available
as stated below in this section are
torque may be limited for a short time,
fulfilled.
especially when the engine
Without touchscreen
temperature is cold. The limitation is
The system is ready to operate when
to allow the lubrication system to fully
the LED in the button D is not
protect the engine.
illuminated. To activate the system
Press D to deactivate the stop-start
when the system is deactivated,
system. The deactivation is indicated
Overrun cut-off
press D. If the stop-start system is
when the LED in the button
temporarily not available and the
illuminates.
The fuel supply is automatically cut off
button D is pressed, the LED in the
during overrun, i.e. when the vehicle
button flashes.
is driven with a gear engaged but
accelerator pedal is released.
158
Driving and operating
With touchscreen
In case of vehicles with automatic
The sliding doors are closed
The stop-start system can be
transmission of type B, an Autostop
The vehicle battery is sufficiently
deactivated in the vehicle
can also be activated at a speed
charged and in good condition.
personalisation 3 124.
below 20 km/h.
The engine is warmed up.
If the system is deactivated during an
The engine will be switched off while
The ambient temperature is
Autostop, the engine restarts
the ignition stays on.
between 0 °C and 35 °C.
immediately.
Indication
The engine coolant temperature
Autostop
is not too high.
The engine exhaust temperature
Vehicles with manual transmission
is not too high, e.g. after driving
An Autostop can be activated at a
with high engine load.
standstill or at a speed below
20 km/h.
The climate control system
allows an Autostop.
Activate an Autostop as follows:
The brake vacuum is sufficient.
● Depress the clutch pedal.
An Autostop is indicated by control
indicator ñ.
The self-cleaning function of the
● Set the selector lever to neutral.
exhaust filter is not active.
● Release the clutch pedal.
During an Autostop, the heating and
brake performance will be
The vehicle was driven at least at
The engine will be switched off while
maintained.
walking speed since the last
the ignition stays on.
Autostop.
Vehicles with automatic transmission
Conditions for an Autostop
Otherwise an Autostop will be
If the vehicle is at a standstill with
The stop-start system checks if each
inhibited.
depressed brake pedal or gear
of the following conditions is fulfilled.
Note
selector in N, Autostop is activated
● The stop-start system is not
The Autostop may be inhibited for
automatically.
manually deactivated.
several hours after a battery
● The driver's door is closed or the
replacement or reconnection.
driver's seat belt is fastened.

 

 

 

 

 

 

 

Content      ..     5      6      7      8     ..