Nissan Sentra (2024 year). Manual in english

• You will not be able to use a hands-free

phone under the following conditions:

– Your vehicle is outside of the cellular

service area.

– Your vehicle is in an area where it is

difficult to receive a cellular signal; such
as in a tunnel, in an underground park-
ing garage, near a tall building or in a
mountainous area.

– Your cellular phone is locked to prevent

it from being dialed.

• When the radio wave condition is not

ideal or ambient sound is too loud, it may
be difficult to hear the other person's
voice during a call.

• Do not place the cellular phone in an area

surrounded by metal or far away from
the in-vehicle phone module to prevent
tone quality degradation and wireless
connection disruption.

• While a cellular phone is connected

through the Bluetooth® wireless connec-
tion, the battery power of the cellular
phone may discharge quicker than usual.
The Bluetooth® Hands-Free Phone Sys-
tem cannot charge cellular phones.

• Some cellular phones or other devices

may cause interference or a buzzing
noise to come from the audio system
speakers. Storing the device in a different
location may reduce or eliminate the
noise.

• For additional information, refer to the

cellular phone owner's manual regarding
the telephone charges, cellular phone
antenna and body, etc.

REGULATORY INFORMATION

FCC Regulatory information
– CAUTION: To maintain compliance with

FCC’s RF exposure guidelines, use only
the supplied antenna. Unauthorized an-
tenna,

modification,

attachments

could damage the transmitter and may
violate FCC regulations.

– Operation is subject to the following two

conditions:

1. This device may not cause interfer-

ence and

2. this device must accept any interfer-

ence, including interference that may
cause undesired operation of the
device.

IC Regulatory information
– Operation is subject to the following two

conditions: (1) this device may not cause
interference, and (2) this device must ac-
cept any interference, including interfer-
ence that may cause undesired opera-
tion of the device.

– This Class B digital apparatus meets all re-

quirements of the Canadian Interference-
Causing Equipment Regulations.

BLUETOOTH® is a
trademark owned by
Bluetooth SIG, Inc. and
licensed to
Panasonic.

USING THE SYSTEM

The system allows hands-free operation of
the Bluetooth® Hands-Free Phone System.

If the vehicle is in motion, some commands
may not be available so full attention may
be given to vehicle operation.

Initialization

When the ignition switch is placed in the ON
position, NISSAN Voice Recognition is initial-
ized, which takes a few seconds. If the
button is pressed before the initialization

4-70

Monitor, climate, audio, phone and voice recognition systems

completes, the system will announce
“There is no phone connected” and will not
react to voice commands.

Operating tips

To get the best performance out of the
NISSAN Voice Recognition System, observe
the following:
• Keep the interior of the vehicle as quiet as

possible. Keep all vents pointed away
from the microphone and close the win-
dows to eliminate surrounding noises
(traffic noises, vibration sounds, etc.),
which may prevent the system from rec-
ognizing voice commands correctly.

• Wait until the tone sounds before speak-

ing a command. Otherwise, the com-
mand will not be received properly.

• Start speaking a command within 5 sec-

onds after the tone sounds.

• Speak in a natural voice without pausing

between words.

• For calling contacts by name, please say

both the first and last name of the con-
tact for better recognition.

Giving voice commands

To operate NISSAN Voice Recognition,
press the

button located on the steer-

ing wheel for less than 1.5 seconds. After
the tone sounds, speak a command.

The command given is picked up by the
microphone, and voice feedback is given
when the command is accepted.
• If a command is not recognized, the sys-

tem announces, “Please say or select a
command from the displayed list.” Make
sure the command is said exactly as
prompted by the system and repeat the
command in a clear voice.

• If you want to go back to the previous

command, you can say “Go back” or “Cor-
rection” any time the system is waiting for
a response.

• You can cancel a command when the

system is waiting for a response by say-
ing, “Cancel” or “Quit.” The system an-
nounces “Exit” and ends the Voice Recog-
nition session. You can also press and
hold the

button on the steering

wheel for 1.5 seconds at any time to end
the Voice Recognition session. Whenever
the Voice Recognition session is can-
celed, a double beep is played to indicate
you have exited the system.

• If you want to adjust the volume of the

voice feedback, push the (+ or -) volume
control switches on the steering wheel
while being provided with feedback. You
can also use the radio volume control
knob.

Voice Prompt Interrupt

In most cases you can interrupt the voice
feedback to speak the next command by
pressing the

button on the steering

wheel. After interrupting the system, wait
for a beep before speaking your command.

One Shot Call (if so equipped)

To use the system faster, you may speak
the second level commands with the main
menu command on the main menu. For
example, press the

button and after

the tone say, “Call Redial”.

Monitor, climate, audio, phone and voice recognition systems

4-71

INDICATORS

When a cellular phone is connected through
the Bluetooth® wireless connection, indica-
tors

for the phone and text messaging

are displayed on the top of the screen.

Indicator

Description

Indicates there are unread received
messages.

Indicates the Bluetooth® device
that is currently connected.

Indicates the strength of the signal
the Bluetooth® device is receiving.

Indicates the amount of remaining
Bluetooth® device battery.

CONTROL BUTTONS

The control buttons for the Bluetooth®
Hands-Free Phone System are located on
the steering wheel.

VOICE COMMAND BUTTON
Press and hold the

button

for more than 1.5 seconds to initi-
ate the Voice Recognition session.
To exit the Voice Recognition ses-
sion press and hold the

for

more than 1.5 seconds. For addi-
tional information, see “Voice
prompt interrupt” (P. 4-71).

You can use the

button to

interrupt the system feedback
and give a command at once.

If an iPhone® is connected, Siri®
can be accessed by pressing the

button for less than 1.5 sec-

onds. For additional information,
see “Siri® Eyes Free” (P. 4-65).

PHONE BUTTON
To answer an incoming call or to
end a call press the

button.

To reject a call press and hold the

button.

LHA4723

LHA4954

4-72

Monitor, climate, audio, phone and voice recognition systems

BLUETOOTH® CONNECTING
PROCEDURE

NOTE:

The connecting procedure must be per-
formed when the vehicle is stationary. If
the vehicle starts moving during the pro-
cedure, the procedure will be canceled.

To connect a phone to the Bluetooth®
Hands-Free Phone System:

Bluetooth® Connecting Procedure

1. Select the “Settings” key on the Launch

Bar.

2. Touch the “Connections” key.

3. Touch the Bluetooth tab and touch the

“Add New” key.

4. Follow the instructions on the screen.

If a PIN appears on the screen, operate the
Bluetooth® device to enter/confirm the
PIN.

Menu Item

Result

Bluetooth

Allows user to switch Bluetooth® on and off. Bluetooth® must be turned on in order to connect a device.

Turns Bluetooth® functionality on. To turn off, touch the “ON” key again. The indicator light will go off.

Favorite (Connection first)

Allows user to toggle “Phone” and “Audio” favorite settings on and off.

Allows user to customize the PIN to a four digit number.

LHA4726

Monitor, climate, audio, phone and voice recognition systems

4-73

NOTE:

Some cellular phones may require you to
accept certain permissions in order to
enable features on your Bluetooth® sys-
tem. During the Bluetooth® pairing pro-
cess, please check your cellular phone’s
display for a pop-up with the request to
grant phonebook access.
Granting phonebook access permission
will allow your contacts to be down-
loaded to the vehicle’s Bluetooth® sys-
tem. A pop-up may display on your cellu-
lar phone stating that the Bluetooth®
system would like to access your con-
tacts and call history. Please select “Al-
low” or Yes” to grant this permission.

Automatic Connecting Procedure

If no phone is connected to the system,
press and hold the

button on the

steering wheel for less than 1.5 seconds.
After the prompt, speak “Add Phone”, the
system will announce “transferring to the
add phone settings menu”. The system will
start the pairing procedure. When a com-
patible phone is found, a message with a
PIN appears on the screen. Operate the
Bluetooth® phone to complete the con-
nection process. For additional informa-
tion, see “Bluetooth® connections screen”
(P. 4-81).

VOICE COMMANDS

Voice commands can be used to operate
the Bluetooth® Hands-Free Phone System.
Press and hold the

button for less

than 1.5 seconds to bring up the phone
command menu. The commands avail-
able are:
• Call <name>
• Dial <number>
• Recent Calls
• Read/Send Text (if so equipped)
• Siri® (if so equipped)
• Voice Assistant (if so equipped)
• Phonebook
• Quick Dial
• Redial
• Select Phone
• Add Phone
• Call <name> Mobile
• Call <name> Home
• Call <name> Office
• Call <name> Main
• Call <name> Other
• Settings

“Call <name>”

Speak this command to make a call to a
contact that is stored in the phonebook.
Say “Call” followed by a phonebook name to
initiate a call. If the system does not recog-
nize the name it will display a list of similar
names. After the prompt, speak or touch
an item number from the displayed list to
place the call.

“Dial <number>”

Speak this command to make a call with a
spoken phone number. After the prompt,
say “Dial” followed by a 7 to 10 digit phone
number. The system will repeat the num-
ber back. Say “Dial” to initiate the call or
“Correction” to re-enter the phone number.

“Recent Calls”

The following commands are available un-
der “Recent Calls”:
• Incoming Calls

Speak this command to list the last 20 in-
coming calls to the vehicle. If the call is from
an entry in the phonebook, the name will
be displayed. Otherwise, the phone num-
ber of the incoming call will be displayed.
When prompted, speak or touch the item
number on the screen to place the call.
Touch the “Next” key to move through the
list of incoming calls.

4-74

Monitor, climate, audio, phone and voice recognition systems

• Outgoing Calls

Speak this command to list the last 20
outgoing calls from the vehicle. If the call
was to an entry in the phonebook, the
name will be displayed. Otherwise, the
phone number of the outgoing call will be
displayed.
When prompted, speak or touch the item
number on the screen to place the call.
Touch the “Next” key to move through the
list of outgoing calls.

• Missed Calls

Speak this command to list the last 20
missed calls to the vehicle. If the call is
from an entry in the phonebook, the
name will be displayed. Otherwise, the
phone number of the missed call will be
displayed.
When prompted, speak or touch the item
number on the screen to place the call.
Touch the “Next” key to move through the
list of missed calls.

“Read Text/Send Text” (if so
equipped)

Speak this command to access text mes-
saging functions.

For additional information, see “Text mes-
saging” (P. 4-78).

“Phonebook through voice
command”

Speak “Phonebook” to view a list of quick
steps to access entries stored in the
phonebook. Commands are organized by
the phone number type selected in the cel-
lular device. For additional information, re-
fer to the cellular phone’s owner’s manual.

The following commands are available:
• <Say a Contact Name>
• <Say a Contact Name> Main
• <Say a Contact Name> Home
• <Say a Contact Name> Mobile
• <Say a Contact Name> Office
• <Say a Contact Name> Other

For additional information on manually se-
lecting phonebook entries, see “Making a
call” (P. 4-77).

“Quick dial”

Speak this command to access the Quick
dial menu. After the prompt, speak or se-
lect an item number on the displayed list to
place the call. For additional information,
see “Making a call” (P. 4-77).

“Redial”

Speak this command to call the last num-
ber dialed. After the prompt, say “Redial” to
dial the number of the last outgoing call.
The system will display “Redialing <name/
number>”. The name of the phonebook en-
try will be displayed if it is available, other-
wise the number being redialed will be
displayed.

“Select Phone”

Speak this command to access the Con-
nections menu. For additional information,
see “Bluetooth® connections screen”
(P. 4-81).

“Add Phone”

Speak this command to access the Con-
nections menu. For additional information,
see “Bluetooth® connections screen”
(P. 4-81).

Monitor, climate, audio, phone and voice recognition systems

4-75

“Settings”

Speak this command to access the Sys-
tem Voice settings menu. The system will
exit Voice Recognition mode. Touch one of
the following options on the screen to
change the settings.
• Beep Only for Opening Prompt

By touching the “ON” key, the indicator
light will illuminate, the system voice will
turn off and only a tone will sound when
the Bluetooth® Hands-Free Phone Sys-
tem is activated. To turn the system voice
back on, touch the “ON” key again, the
indicator light will turn off.

• Best Match List

When the system doesn't recognize a
phonebook name or dial number, it will
provide a list of similar sounding results.
To turn this off, touch the “ON” key, the
indicator light will turn off. To turn on,
touch the “ON” key again, the indicator
light will turn on.

PHONE DISPLAY SCREEN

The Phone screen can be displayed by
pressing the

button on the control

panel.

The following options are displayed:
• Quick Dial

Displays the Quick Dial screen. For addi-
tional information, see “Quick dial” (P. 4-75)

• Phonebook

Displays the Phonebook screen. For addi-
tional information, see “Making a call”
(P. 4-77).

• Call History

Displays the Call History screen. For addi-
tional information, see “Making a call”
(P. 4-77).

• Dial Number

Displays the Dial Number screen. For ad-
ditional information, see “Making a call”
(P. 4-77).

• Text Message

Displays the received message screen.
For additional information, see “Text mes-
saging” (P. 4-78).

• Connections

Displays the Connections screen. For ad-
ditional information, see “Bluetooth® con-
nections screen” (P. 4-81).

• Volume

Displays the volume adjustment screen.
For additional information, see “Volume &
beeps” (P. 4-84).

LHA4705

4-76

Monitor, climate, audio, phone and voice recognition systems

MAKING A CALL

1. Press the

button on the Launch Bar.

The “Phone” screen will appear on the
display.

2. Select one of the options to make a call.

Phonebook

To access the phonebook:

1. Press the

button on the steering

wheel or touch the “

” key on the

launch bar.

2. Touch the “Phonebook” key.

3. Choose the desired entry from the dis-

played list.

Call History

1. Select a phonebook name or phone

number from the recent incoming, out-
going, or missed calls tabs.

2. Touch a phonebook name or phone

number listed to initiate the call.

Dial Number

1. Enter the phone number manually using

the keypad displayed on the screen.

2. Touch the “OK” key on the screen to initi-

ate the call.

For additional options to make a call, see
“Voice commands” (P. 4-74).

DURING A CALL

While a call is active the following options
will appear on the control panel display:
• Mute

Touch this key to mute or unmute the
system.

• Dial Number

Touch this key to dial digits during the
phone call.

• Switch to Handset

Touch the “Use Handset” key on the screen
to transfer the call to the handset (cellular
phone). To transfer the call back from the
handset to the Bluetooth® Hands-Free
Phone System, press the

button on

the control panel then select the “Transfer
Hands-free” key on the screen.

NOTE:

Some jurisdictions prohibit the use of
cellular telephones while driving.

• Switch Call
This option will only be available when a
second call is active.

supported

the

phone,

the

Bluetooth® Hands-Free Phone System
allows for call waiting functionality. If a
call is received while another call is al-
ready active, a message will be displayed
on the screen. Press the

button on

the steering wheel or touch the “
Answer” key on screen to accept the in-
coming call. Touch the “

Decline” key

on the screen to reject the second call.

While a call is active, press the

button

on the steering wheel to access additional
options.

Speak

one

the

following

commands:
• “Send Digits”

Speak this command followed by the dig-
its to enter digits during the phone call.

• “Switch call”

Speak this command to hold the second
call and switch back to the original call.

Monitor, climate, audio, phone and voice recognition systems

4-77

RECEIVING/ENDING A CALL

When a call is received by the phone con-
nected to the vehicle’s Bluetooth® Hands-
Free Phone System, the call information is
displayed on the control panel display.

To accept the incoming call, either:
• Press the

button on the steering

wheel, or

• Touch the “

Answer” key on the

screen.

To end or reject an incoming call, either:
• Press and hold the

button on the

steering wheel, or

• Touch the “

Decline” key on the

screen.

If the user is not able to answer the call
right away, touch the “Hold Call” key dis-
played on the screen. A message will be
played for the caller: “I’m not able to take a
call right now.” The user may then accept
the call when available or reject the call.

TEXT MESSAGING (if so equipped)

WARNING

•

Laws in some jurisdictions may re-
strict the use of “Text-to-Speech”.
Check local regulations before using
this feature.

•

Laws in some jurisdictions may re-
strict the use of some of the applica-
tions and features, such as social
networking and texting. Check local
regulations for any requirements.

•

Use the text messaging feature after
stopping your vehicle in a safe loca-
tion. If you have to use the feature
while

driving,

exercise

extreme

caution at all times so full attention
may be given to vehicle operation.

•

If you are unable to devote full atten-
tion to vehicle operation while using
the text messaging feature, pull off
the road to a safe location and stop
your vehicle.

NOTE:

This feature is automatically disabled if the
connected device does not support the
Message Access Profile (MAP). For addi-
tional information, refer to the phone’s
owner’s manual for details and instructions.

NOTE:

Many phones may require special per-
mission to enable text messaging. Check
the phone’s screen during Bluetooth®
pairing. For some phones, you may need
to enable ‘Notifications’ in the phone’s
Bluetooth® menu for text messages to
appear on the headunit. For additional
information, refer to your phone’s own-
er’s manual. Text message integration
requires that the phone support MAP
(Message Access Profile) for both receiv-
ing and sending text messages. Some
phones may not support all text mes-
saging

features.

Please

refer

www.nissanusa.com/bluetooth

www.nissan.ca/bluetooth for compat-
ibility information, as well as your de-
vice’s owner’s manual.

The system allows for the sending and re-
ceiving of text messages through the ve-
hicle interface.

The availability of the text message func-
tion may vary depending on the cellular
phone.

4-78

Monitor, climate, audio, phone and voice recognition systems

When the cellular phone connected to the
vehicle receives a text message, a notifica-
tion will appear on the control panel dis-
play. To check the message, touch the
“Read” key. Touch the “Ignore” key to save
the message to be checked later.

Access text messaging through the ve-
hicles Bluetooth® Hands-Free Phone or
through the vehicles control panel.

Text messaging using Bluetooth®
Hands-Free Phone System (if so
equipped)

Sending a text message (if so equipped)

1. Press and hold the

button on the

steering wheel for less than 1.5 seconds.

2. Say “Send Text” after the tone.

3. The system will provide a list of available

commands in order to determine the
recipient of the text message. Choose
from the following:

• Phonebook
• Quick Dial
• Incoming Calls
• Outgoing Calls
• Missed Calls
• Dial

4. Once a recipient is chosen, the system

prompts for which message to send.
Nine predefined messages are avail-
able. To choose one of the predefined
messages, speak one of the following
after the tone:

• “Driving, can't text”
• “Call me”
• “On my way”
• “Running late”
• “Okay”
• “Yes”
• “No”
• “Where are you?”
• “When?”

Reading a received text message

1. Press and hold the

button on the

steering wheel for less than 1.5 seconds.

2. Say “Read Text” after the tone.

The display will show a list of 20 messages
with the sender and delivery time. Touch
the “Next” key on the screen to view all mes-
sages. To view a text message press the

button on the steering wheel and

speak the number item list on the screen.
The following options will be available:

• Play

Speak this command to have the system
say the message.

• Reply

Speak this command to send a text mes-
sage response to the sender of the text
message.

• Call

Speak this command to call the sender.

• Previous

Speak this command to move to the pre-
vious text message (if available).

• Next

Speak this command to move to the next
text message (if available).

Siri® Eyes Free

If a connected phone is equipped with Siri®,
it can also be used to create custom mes-
sages that are sent through the phone. For
additional information, see “Siri® Eyes Free”
(P. 4-65).

NOTE:

Text messages are only displayed if the
vehicle speed is less than 5 mph (8 km/h).

NOTE:

For Apple iPhones®, text messages can
only be sent through Siri.

Monitor, climate, audio, phone and voice recognition systems

4-79

Text messaging using the control
panel

Display received message list

1. Press the

button on the control

panel.

2. Touch the “Text Message” key on the

screen

3. Touch an item on the list to read or reply

to the message.

Up to 100 messages can be stored in the
message list.

Received message screen

Touching the “Read” key on the incoming mes-
sage notification screen or selecting a mes-
sage from the message list will show the de-
tails of the received message on the display.

Available actions:
• Prev.

Touch this key to read the previous
message.

• Next

Touch this key to read the next message.

• Play/Stop

Touch the “Play” key to have the hands-
free phone system read out the received
message. Touch the “Stop” key to stop
reading.

• Call

If the sender of the message is registered
in the phonebook, touch the “Call” key to
make a call to the sender.

• Reply

A reply message can be selected from
the predefined list.

Sending a text message (if so equipped)

This function may not be supported de-
pending on the cellular phone.

1. Press the

button on the control

panel.

2. Touch the “Text Message” key on the

screen.

3. Touch the “Create Message” key on the

screen.

The following items are available:

Available item

Action

Enter Number by Keypad

Enter the phone number of the recipient using the keypad. Touch the “OK” key to confirm.

Quick Dial

Select a recipient from the quick dial list.

Phonebook

Select a recipient from the phonebook.

Call History

Select a recipient/phone number from call history.

Select Text

Touch to display a list of predefined text messages.

Send

Touch to send the message.

4-80

Monitor, climate, audio, phone and voice recognition systems

BLUETOOTH® CONNECTIONS
SCREEN

“

” (back) key

Bluetooth tab

Connections screen

“Add New” key

“

” (settings) key

“

” (info) key

“

” (Bluetooth® Audio connection) key

“

” (Bluetooth® Hands-Free Phone

System connection) key

Access the Connections screen to change
settings and view Bluetooth® information.
To access the Connections screen press
the

MENU button on the control panel.

Touch the “Connections” key on the screen
then select the Bluetooth tab.

The paired phone will be added to the list
on the Bluetooth® connections screen.

Touching the name of another device on
the list will switch the connected device.

“

” (back) key

Touch the “

” key to go back to the

previous screen.

Connecting Bluetooth®

For additional information on connecting a
cellular phone or device to the Bluetooth®
Hands-Free Phone System, see “Bluetooth®
connecting procedure” (P. 4-73).

NOTE:

Some cellular phones or other devices
may cause interference or a buzzing
noise to come from the audio system
speakers. Storing the device in a differ-
ent location may reduce or eliminate the
noise.

Bluetooth tab

This tab will display up to six Bluetooth®
devices. If six devices are already con-
nected, one of the devices must be deleted
before another device can be connected.

“Add New” key

Touch the key on the screen to connect a
new Bluetooth® device. For additional in-
formation, see “Bluetooth® connecting
procedure” (P. 4-73).

“

” (Bluetooth® settings) key

Touch the “

” key on the screen to

display a list of options.
•

Bluetooth

Touch this key to turn the Bluetooth®
connection on or off

•

Favorite (Connection first)

Touch this key to change which device
will be connected first when multiple de-
vices are connected to the vehicle.
Turn the “

” key on or off to make the

device a favorite connection.
Turn the “

” key on or off to make the

device a favorite connection.

LHA4716

Monitor, climate, audio, phone and voice recognition systems

4-81

•

Pin

Touch this key to customize the PIN code.
Input a four digit number then touch the
“OK” key. The new PIN will be set.

“

” (info) key

Touch the “

” key on the screen to

display the information of the cellular
phone or to delete the device.

Touch the “Delete” key to remove a paired
device then select “Yes” when a message
appears.

“

” (Bluetooth® Hands-Free

Phone System connection) key

A list of connected devices will be displayed
on the screen. Touch the “

” key next to

the name to connect a device to the
Hands-Free Phone System. If the phone is
listed as a favorite, a star will appear on the
icon. Touch the key again to disconnect the
device. The device will not be removed
from the list. For additional information on
removing a device, see “

(info) key”

(P. 4-82).

“

” (Bluetooth® Audio

connection) key

A list of connected devices will be displayed
on the screen. Touch the “

” key next to

the

name

connect

device

Bluetooth® Audio. If the device is listed as a
favorite, a star will appear on the icon.
Touch the key again to disconnect the de-
vice. The device will not be removed from
the list. For additional information on re-
moving a device, see “

(info) key”

(P. 4-82).

PHONE AND TEXT MESSAGE
SETTINGS

Bluetooth® Hands-Free Phone System set-
tings can be changed according to the us-
er’s preference. To access the “Phone” set-
tings menu press the

MENU button on

the control panel. Touch the “Settings” key
then select the “Phone” key.

LHA4721

4-82

Monitor, climate, audio, phone and voice recognition systems

The following options are available:

Menu Item

Result

Quick Dial

Edit

Entries in the Quick Dial can be edited. For additional information, see “Quick dial” (P. 4-75).

Delete All

Deletes all of the stored phone numbers in quick dial.

Phonebook

Download Entire Phone-
book

All the phone numbers that are stored in a phonebook in the cellular phone that is connected to the vehicle are
downloaded at once. For additional information, refer to the cellular phone’s owner’s manual.

Auto Downloaded

Turns on/off automatic downloading of the phonebook when a new phone is connected.

Text Message

Turns the text messaging function on/off.

Text Message Ringtone

Turn the incoming message sound on/off.

Signature

Turns the signature setting for the outgoing text message on/off.

Auto Reply

Turns the automatic text message reply function on/off.

Auto Reply Text Message

Select the text message to be used for the automatic reply. Choose from a list of predefined messages.

Notifications

Driver Only

When this item is turned on, incoming call notification is displayed only on the handset.

Vehicle Ringtone

Turns the vehicle ringtone on/off.

Automatic Hold

When this item turns on, an incoming call will be put on hold automatically.

Monitor, climate, audio, phone and voice recognition systems

4-83

Volume & beeps

There are several methods to customize
the volume settings.

Volume & Beeps

The Volume & Beeps screen can be found
by pressing the

MENU button on the

control panel, touching the “Settings” key
on the screen and selecting “Volume &
Beeps”. To adjust the volume of the follow-
ing options, touch the “–” and “+” keys on the
screen.

The available settings are:
• Ringtone

Adjust the volume level of the ringtone of
incoming calls.

• Outgoing Call

Adjust the volume level of the outgoing
calls.

• Voice Prompt Vol.

Adjust the volume level of the system
voice.

• Text-to-speech Vol.

Adjust the volume of the replay voice for
text messaging.

• Button Beeps

Turns on/off the button beep sounds and
alarm for prohibited operations.

Volume Settings

The Volume settings screen can be found
by pressing the

button on the control

panel then touching the “Volume” key on
the screen. To adjust the volume of the
following options, touch the “–” and “+” keys
on the screen.

The available settings are:
• Ringtone

Adjust the volume level of the ringtone of
incoming calls.

• Outgoing Call

Adjust the volume level of the outgoing
calls.

“Made for iPod”, “Made for iPhone” and
“Made for iPad” mean that an electronic
accessory has been designed to connect
specifically to iPod, iPhone or iPad, respec-
tively, and has been certified by the devel-
oper to meet Apple performance stan-
dards. Apple is not responsible for the
operation of this device or its compliance
with safety and regulatory standards.
Please note that the use of this accessory
with iPod, iPhone or iPad may affect wire-
less performance.

iPad, iPhone, iPod classic, iPod nano, iPod
shuffle and iPod touch are trademarks of
Apple Inc., registered in the U.S. and other
countries. Lightning is a trademark of
Apple Inc.

iPod®/iPhone®

4-84

Monitor, climate, audio, phone and voice recognition systems

WARNING

•

Do not leave children or adults who
would normally require the assis-
tance of others alone in your vehicle.
Pets should also not be left alone.
They could accidentally injure them-
selves or others through inadvertent
operation of the vehicle. Also, on hot,
sunny days, temperatures in a closed
vehicle could quickly become high
enough to cause severe or possibly
fatal injuries to people or animals.

•

Closely supervise children when they
are around cars to prevent them
from playing and becoming locked in
the trunk where they could be seri-
ously injured. Keep the car locked,
with the rear seatback and trunk lid
securely latched when not in use, and
prevent children's access to car keys.

EXHAUST GAS (carbon monoxide)

WARNING

•

Do not breathe exhaust gases; they
contain colorless and odorless car-
bon monoxide. Carbon monoxide is
dangerous. It

can

cause

uncon-

sciousness or death.

•

If you suspect that exhaust fumes
are entering the vehicle, drive with all
windows fully open, and have the ve-
hicle inspected immediately.

•

Do not run the engine in closed
spaces such as a garage.

•

Do not park the vehicle with the en-
gine running for any extended length
of time.

•

Keep the rear vent windows, doors
and trunk lids (if so equipped) closed
while

driving,

otherwise

exhaust

gases could be drawn into the pas-
senger compartment. If you must
drive with one of these open, follow
these precautions:

1. Open all the windows.
2. Set the

air recirculation but-

ton to off and the fan control dial
to high to circulate the air.

•

If electrical wiring or other cable con-
nections must pass to a trailer
through the seal on the trunk lid or
the body, follow the manufacturer's
recommendation to prevent carbon
monoxide entry into the vehicle.

•

The exhaust system and body should
be inspected by a qualified mechanic
whenever:

a. The vehicle is raised for service.
b. You suspect that exhaust fumes

are entering into the passenger
compartment.

c. You notice a change in the sound

of the exhaust system.

d. You have had an accident involv-

ing damage to the exhaust sys-
tem, underbody, or rear of the
vehicle.

THREE-WAY CATALYST

The three-way catalyst is an emission con-
trol device installed in the exhaust system.
Exhaust gases in the three-way catalyst
are burned at high temperatures to help
reduce pollutants.

WARNING

•

The exhaust gas and the exhaust
system are very hot. Keep people,
animals

flammable

materials

away

from

the

exhaust

system

components.

•

Do not stop or park the vehicle over
flammable materials such as dry
grass, waste paper or rags. They may
ignite and cause a fire.

PRECAUTIONS WHEN STARTING AND
DRIVING

5-4

Starting and driving

CAUTION

•

Do not use leaded gasoline. Deposits
from leaded gasoline will seriously
reduce the three-way catalyst's abil-
ity to help reduce exhaust pollutants.

•

Keep your engine tuned up. Malfunc-
tions in the ignition, fuel injection, or
electrical systems can cause overrich
fuel flow into the three-way catalyst,
causing it to overheat. Do not keep
driving if the engine misfires, or if no-
ticeable loss of performance or other
unusual operating conditions are de-
tected. Have the vehicle inspected
promptly. It is recommended that
you visit a NISSAN dealer for this
service.

•

Avoid driving with an extremely low
fuel level. Running out of fuel could
cause the engine to misfire, damag-
ing the three-way catalyst.

•

Do not race the engine while warm-
ing it up.

•

Do not push or tow your vehicle to
start the engine.

TIRE PRESSURE MONITORING
SYSTEM (TPMS)

Each tire, including the spare (if provided),
should be checked monthly when cold and
inflated to the inflation pressure recom-
mended by the vehicle manufacturer on
the vehicle placard or tire inflation pressure
label. (If your vehicle has tires of a different
size than the size indicated on the vehicle
placard or tire inflation pressure label, you
should determine the proper tire inflation
pressure for those tires.)

As an added safety feature, your vehicle
has been equipped with a Tire Pressure
Monitoring System (TPMS) that illuminates
a low tire pressure telltale when one or
more of your tires is significantly under-
inflated. Accordingly, when the low tire
pressure telltale illuminates, you should
stop and check all your tires as soon as
possible, and inflate them to the proper
pressure. Driving on a significantly under-
inflated tire causes the tire to overheat and
can lead to tire failure. Under-inflation also
reduces fuel efficiency and tire tread life,
and may affect the vehicle’s handling and
stopping ability.

Please note that the TPMS is not a substi-
tute for proper tire maintenance, and it is
the driver’s responsibility to maintain cor-
rect tire pressure, even if under-inflation
has not reached the level to trigger illumi-
nation of the TPMS low tire pressure telltale.

Your vehicle has also been equipped with a
TPMS malfunction indicator to indicate
when the system is not operating properly.
The TPMS malfunction indicator is com-
bined with the low tire pressure telltale.
When the system detects a malfunction,
the telltale will flash for approximately one
minute and then remain continuously illu-
minated. This sequence will continue upon
subsequent vehicle start-ups as long as
the malfunction exists. When the malfunc-
tion indicator is illuminated, the system
may not be able to detect or signal low tire
pressure as intended. TPMS malfunctions
may occur for a variety of reasons, includ-
ing the installation of replacement or alter-
nate tires or wheels on the vehicle that
prevent the TPMS from functioning prop-
erly. Always check the TPMS malfunction
telltale after replacing one or more tires or
wheels on your vehicle to ensure that the
replacement or alternate tires and wheels
allow the TPMS to continue to function
properly.

Starting and driving

5-5

Additional information:

• When using a wheel without the TPMS

such as the spare tire, the TPMS does not
monitor the tire pressure of the spare tire.

• The TPMS will activate only when the ve-

hicle is driven at speeds above 16 mph (25
km/h). Also, this system may not detect a
sudden drop in tire pressure (for example,
a flat tire while driving).

• The low tire pressure warning light does

not automatically turn off when the tire
pressure of all your tires is adjusted. After
the tires are inflated to the recom-
mended pressure, the vehicle must be
driven at speeds above 16 mph (25 km/h)
to activate the TPMS and turn off the low
tire pressure warning light. Use a tire
pressure

gauge

check

the

tire

pressure.

• The “Tire Pressure Low - Add Air” warning

message is displayed in the odometer
when the low tire pressure warning light
is illuminated and low tire pressure is de-
tected. The “Tire Pressure Low - Add Air”
warning message turns off when the low
tire pressure warning light turns off. The
low tire pressure warning light remains
illuminated until the tires are inflated to
the recommended COLD tire pressure.

The “Tire Pressure Low - Add Air” warning
message is displayed each time the igni-
tion switch is placed in the ON position as
long as the low tire pressure warning light
remains illuminated.

• The “Tire Pressure Low - Add Air” warning

is not displayed if the low tire pressure
warning light illuminates to indicate a
TPMS malfunction.

• Tire pressure rises and falls depending on

the heat caused by the vehicle’s opera-
tion and the outside temperature. Do not
reduce the tire pressure after driving be-
cause the tire pressure rises after driving.
Low outside temperature can lower the
temperature of the air inside the tire
which can cause a lower tire inflation
pressure. This may cause the low tire
pressure warning light to illuminate. If the
warning light illuminates, check the tire
pressure for all four tires.

• The Tire and Loading Information label is

located in the driver's door opening.

For additional information, see “Tire Pres-
sure Low - Add Air ” (P. 2-31) or (P. 2-50), “Low
tire pressure warning light” (P. 2-12) or “Tire
Pressure Monitoring System (TPMS)” (P. 6-3).

WARNING

•

Radio waves could adversely affect
electric medical equipment. Those
who use a pacemaker should contact
the

electric

medical

equipment

manufacturer for the possible influ-
ences before use.

•

If the low tire pressure warning light
illuminates while driving, avoid sud-
den steering maneuvers or abrupt
braking, reduce vehicle speed, pull
off the road to a safe location and
stop the vehicle as soon as possible.
Driving with under-inflated tires may
permanently damage the tires and
increase the likelihood of tire failure.
Serious vehicle damage could occur
and may lead to an accident and
could result in serious personal in-
jury. Check the tire pressure for all
four tires. Adjust the tire pressure to
the recommended COLD tire pres-
sure shown on the Tire and Loading
Information label to turn the low tire
pressure warning light off. If you have
a flat tire, replace it with a spare tire
as soon as possible. For additional
information on changing a flat tire,
see “Flat tire” (P. 6-3).

5-6

Starting and driving

•

When using a wheel without the
TPMS such as the spare tire, when a
spare tire is mounted or a wheel is
replaced, the TPMS will not function
and the low tire pressure warning
light will flash for approximately 1
minute. The light will remain on after
1 minute. Have your tires replaced
and/or TPMS reset as soon as pos-
sible. It is recommended that you
visit a NISSAN dealer for this service.

•

Replacing tires with those not origi-
nally specified by NISSAN could af-
fect the proper operation of the
TPMS.

•

Do not inject any tire liquid or aerosol
tire sealant into the tires, as this may
cause a malfunction of the tire pres-
sure sensors.

CAUTION

Do not place metalized film or any
metal parts (antenna, etc.) on the win-
dows. This may cause poor reception of
the signals from the tire pressure sen-
sors, and the TPMS will not function
properly.

Some devices and transmitters may tem-
porarily interfere with the operation of the
TPMS and cause the low tire pressure
warning light to illuminate.

Some examples are:
• Facilities or electric devices using similar

radio frequencies are near the vehicle.

• If a transmitter set to similar frequencies

is being used in or near the vehicle.

• If a computer (or similar equipment) or a

DC/AC converter is being used in or near
the vehicle.

The low tire pressure warning light may
illuminate in the following cases:
• If the vehicle is equipped with a wheel and

tire without TPMS.

• If the TPMS has been replaced and the ID

has not been registered.

• If the wheel is not originally specified by

NISSAN.

NOTE:

This device complies with part 15 of the
FCC Rules. Operation is subject to the fol-
lowing two conditions: (1) This device
may not cause harmful interference, and
(2) this device must accept any interfer-
ence received, including interference
that may cause undesired operation.

NOTE:

L’émetteur/récepteur exempt de licence
contenu dans le présent appareil est
conforme aux CNR d’Innovation, Sci-
ences et Développement économique
Canada applicables aux appareils radio
exempts de licence. L’exploitation est au-
torisée aux deux conditions suivantes:

1. L’appareil ne doit pas produire de

brouillage;

2. L’appareil doit accepter tout brouil-

lage radioélectrique subi, même si le
brouillage est susceptible d’en com-
promettre le fonctionnement.

FCC WARNING

Changes or modifications not expressly
approved by the party responsible for
compliance could void the user's author-
ity to operate the equipment.

Starting and driving

5-7

TPMS with Easy-Fill Tire Alert

When adding air to an under-inflated tire,
the TPMS with Easy-Fill Tire Alert provides
visual and audible signals outside the ve-
hicle to help you inflate the tires to the rec-
ommended COLD tire pressure.

Vehicle set-up:

1. Park the vehicle in a safe and level place.

2. Apply the parking brake and place the

shift lever in the P (Park) position (if so
equipped).

3. Place the ignition switch in the ON posi-

tion. Do not start the engine.

Operation:

1. Add air to the tire.

2. After a few seconds, the hazard indica-

tors will start flashing.

3. When

the

designated

pressure

reached, the horn beeps once and the
hazard indicators stop flashing.

4. Perform the above steps for each tire.

• If the tire is over-inflated more than

approximately 4 psi (30 kPa), the horn
beeps and the hazard indicators flash
three times. To correct the pressure,
push the core of the valve stem on the

tire briefly to release pressure. When
the pressure reaches the designated
pressure, the horn beeps once.

• If the hazard indicator does not flash

within approximately 15 seconds after
starting to inflate the tire, it indicates that
the Easy-Fill Tire Alert is not operating.

• The TPMS will not activate the Easy-Fill

Tire Alert under the following conditions:

– If there is interference from an ex-

ternal device or transmitter.

– The air pressure from the inflation

device is not sufficient to inflate the
tire.

– There is a malfunction in the TPMS

system.

– There is a malfunction in the horn

or hazard indicators.

– The identification code of the tire’s

pressure sensor is not registered to
the system.

– The battery of the tire pressure

sensor is low.

• If the Easy-Fill Tire Alert does not oper-

ate due to TPMS interference, move
the vehicle about 3 ft (1 m) backward
or forward and try again.

If the Easy-Fill Tire Alert is not working, use a
tire pressure gauge.

AVOIDING COLLISION AND
ROLLOVER

WARNING

Failure to operate this vehicle in a safe
and prudent manner may result in loss
of control or an accident.

Be alert and drive defensively at all times.
Obey all traffic regulations. Avoid excessive
speed, high speed cornering, or sudden
steering maneuvers, because these driving
practices could cause you to lose control of
your vehicle.

As with any vehicle, loss of control could
result in a collision with other vehicles or
objects or cause the vehicle to roll over,
particularly if the loss of control causes
the vehicle to slide sideways.

Be attentive at all times, and avoid driving
when tired. Never drive when under the in-
fluence of alcohol or drugs (including pre-
scription or over-the-counter drugs which
may cause drowsiness). Always wear your
seat belt as outlined in the “Safety – Seats,
seat belts and supplemental restraint sys-
tem” section of this manual, and also in-
struct your passengers to do so.

5-8

Starting and driving

Seat belts help reduce the risk of injury in
collisions and rollovers.

In a rollover crash, an unbelted person is
significantly more likely to die than a
person wearing a seat belt.

OFF-ROAD RECOVERY

While driving, the right side or left side
wheels may unintentionally leave the road
surface. If this occurs, maintain control of
the vehicle by following the procedure be-
low. Please note that this procedure is only
a general guide. The vehicle must be driven
as appropriate based on the conditions of
the vehicle, road and traffic.

1. Remain calm and do not overreact.

2. Do not apply the brakes.

3. Maintain a firm grip on the steering

wheel with both hands and try to hold a
straight course.

4. When appropriate, slowly release the ac-

celerator pedal to gradually slow the
vehicle.

5. If there is nothing in the way, steer the

vehicle to follow the road while vehicle
speed is reduced. Do not attempt to
drive the vehicle back onto the road sur-
face until vehicle speed is reduced.

6. When it is safe to do so, gradually turn

the steering wheel until both tires return
to the road surface. When all tires are on
the road surface, steer the vehicle to
stay in the appropriate driving lane.

• If you decide that it is not safe to return

the vehicle to the road surface based
on vehicle, road or traffic conditions,
gradually slow the vehicle to a stop in
a safe place off the road.

RAPID AIR PRESSURE LOSS

Rapid air pressure loss or a “blow-out” can
occur if the tire is punctured or is damaged
due to hitting a curb or pothole. Rapid air
pressure loss can also be caused by driving
on under-inflated tires.

Rapid air pressure loss can affect the han-
dling and stability of the vehicle, especially
at highway speeds.

Help prevent rapid air pressure loss by
maintaining the correct air pressure and
visually inspecting the tires for wear and
damage. For additional information, see
“Wheels and tires” (P. 8-29). If a tire rapidly
loses air pressure or “blows-out” while driv-
ing, maintain control of the vehicle by fol-
lowing the procedure below. Please note
that this procedure is only a general guide.

The vehicle must be driven as appropriate
based on the conditions of the vehicle, road
and traffic.

WARNING

If there is a sudden loss of tire air pres-
sure, the vehicle will generally move or
pull in the direction of the flat tire. In
this situation, losing control of the ve-
hicle may cause a collision and result in
personal injury.
To help avoid loss of control:

•

Do not rapidly apply the brakes.

•

Do not rapidly release the accelerator
pedal.

•

Do not rapidly turn the steering
wheel.

1. Remain calm and do not overreact.

2. Maintain a firm grip on the steering

wheel with both hands and try to hold a
straight course.

3. When appropriate, slowly release the ac-

celerator pedal to gradually slow the
vehicle.

Starting and driving

5-9

4. Gradually steer the vehicle to a safe lo-

cation off the road and away from traffic
if possible.

5. Lightly apply the brake pedal to gradu-

ally stop the vehicle.

6. Turn on the hazard warning flashers and

contact a roadside emergency service
to change the tire. For additional infor-
mation, see “Changing a flat tire” (P. 6-3 ).

DRINKING ALCOHOL/DRUGS AND
DRIVING

WARNING

Never drive under the influence of alco-
hol or drugs. Alcohol in the blood-
stream reduces coordination, delays
reaction time and impairs judgement.
Driving after drinking alcohol increases
the likelihood of being involved in an
accident injuring yourself and others.
Additionally, if you are injured in an ac-
cident, alcohol can increase the sever-
ity of the injury.

NISSAN is committed to safe driving. How-
ever, you must choose not to drive under the
influence of alcohol. Every year thousands of
people are injured or killed in alcohol-related
collisions. Although the local laws vary on

what is considered to be legally intoxicated,
the fact is that alcohol affects all people dif-
ferently and most people underestimate the
effects of alcohol.

Remember, drinking and driving don't mix!
That is true for drugs (over-the-counter,
prescription) and illegal drugs, too. Don't
drive if your ability to operate your vehicle is
impaired by alcohol, drugs, or some other
physical condition.

WARNING

Do not operate the push-button igni-
tion switch while driving the vehicle ex-
cept in an emergency. (The engine will
stop when the ignition switch is pushed
three consecutive times in quick suc-
cession or the ignition switch is pushed
and held for more than 2 seconds.) If
the engine stops while the vehicle is
being driven, this could lead to a crash
and serious injury.

LSD2645

PUSH-BUTTON IGNITION SWITCH

5-10

Starting and driving

When the ignition switch is pushed without
depressing the brake pedal, the ignition
switch position will illuminate as follows:

Push center:
• Once to change to the ON position.
• Two times to change to the OFF position.

The ignition switch will automatically re-
turn to the LOCK position when any door is
either opened or closed with the switch in
the OFF position.

The ignition lock is designed so that the
ignition switch position cannot be placed
in the OFF position until the shift lever is
moved to the P (Park) position.

When the ignition switch cannot be pushed
toward the OFF position, proceed as fol-
lows:

1. Move the shift lever to the P (Park)

position.

2. Push the ignition switch. The ignition

switch position will change to the ON
position.

3. Push the ignition switch again to the

OFF position.

The shift lever can be moved from the P
(Park) position if the ignition switch is in
the ON position and the brake pedal is
depressed.

If the battery of the vehicle is discharged,
the ignition switch cannot be moved
from the LOCK position.

Some indicators and warnings for opera-
tion are displayed in the meter. For addi-
tional information, see “Warning lights, indi-
cator lights and audible reminders” (P. 2-8).

OPERATING RANGE

The Intelligent Key functions can only be
used when the Intelligent Key is within the
specified operating range.

When the Intelligent Key battery is almost
discharged or strong radio waves are pres-
ent near the operating location, the Intelli-
gent Key system’s operating range be-
comes narrower and may not function
properly.

If the Intelligent Key is within the operating
range, it is possible for anyone, even someone
who does not carry the Intelligent Key, to push
the ignition switch to start the engine.

LSD2089

Starting and driving

5-11

The operating range of the engine start
function is inside of the vehicle

• The luggage area is not included in the

operating range, but the Intelligent Key
may function.

• If the Intelligent Key is placed on the in-

strument panel or inside the glove box,
storage bin or door pocket, the Intelligent
Key may not function.

• If the Intelligent Key is placed near the

door or window outside the vehicle, the
Intelligent Key may function.

PUSH-BUTTON IGNITION SWITCH
POSITIONS

LOCK (Normal parking position)

The ignition switch can only be locked in
this position.

The ignition switch will be unlocked when it
is pushed to the ON position while carrying
the Intelligent Key.

The ignition switch will lock when any door
is opened or closed with the ignition
switched off.

ON (Normal operating position)

The ignition system and the electrical ac-
cessory power activate at this position
without the engine turned on.

The ON position has a battery saver feature
that will place the ignition switch in the OFF
position, if the vehicle is not running, after
some time.

CAUTION

Do not leave the vehicle with the igni-
tion switch in the AUTO ACC or ON posi-
tion when the engine is not running for
an extended period. This can discharge
the battery.

OFF

The ignition switch is in the OFF position
when the engine is turned off using the
ignition switch. No lights will illuminate on
the ignition switch.

AUTO ACC:

With the vehicle in the P (Park) position, the
Intelligent Key with you, and the ignition
switch placed from the ON to the OFF po-
sition, the radio can still be used for a period
of time, or until the driver’s door is opened.

After a period of time, functions such as
radio, navigation, and Bluetooth® Hands-
Free Phone System may be restarted by
pressing the “POWER button/VOLUME con-
trol knob” or the key fob unlock button. For
additional information, see the “Monitor, cli-
mate, audio, phone and voice recognition
systems” section of this manual.

EMERGENCY ENGINE SHUT OFF

To shut off the engine in an emergency
situation while driving, perform the follow-
ing procedure:
• Rapidly push the ignition switch three

consecutive times in less than 1.5 sec-
onds, or

• Push and hold the ignition switch for

more than 2 seconds.

5-12

Starting and driving

NISSAN INTELLIGENT KEY®
BATTERY DISCHARGE

If the battery of the NISSAN Intelligent Key®
is discharged or environmental conditions
interfere with the Intelligent Key operation,
start the engine according to the following
procedure:

1. Place the shift lever in the P (Park)

position.

2. Firmly apply the foot brake.

3. Touch the ignition switch with the Intel-

ligent Key as illustrated. (A chime will
sound.)

After step 3 is performed, when the igni-
tion switch is pushed without depress-
ing the brake pedal, the ignition switch
position will change to the ON position.

4. Push the ignition switch while depress-

ing the brake pedal within 10 seconds
after the chime sounds. The engine will
start.

NOTE:
• When the ignition switch is pushed to

the ON position or the engine is started
by the above procedure, the Intelligent
Key battery discharge indicator ap-
pears in the vehicle information dis-
play even when the Intelligent Key is
inside the vehicle. This is not a mal-
function. To turn off the Intelligent Key
battery discharge indicator, touch the
ignition switch with the Intelligent Key
again.

• If the Intelligent Key battery discharge

indicator appears, replace the battery
as soon as possible. For additional in-
formation, see “Battery replacement”
(P. 8-23).

NISSAN VEHICLE IMMOBILIZER
SYSTEM

The NISSAN Vehicle Immobilizer System
will not allow the engine to start without
the use of the registered key.

If the engine fails to start using a registered
key (for example, when interference is
caused by another registered key, an auto-
mated toll road device or automatic pay-
ment device on the key ring), restart the
engine using the following procedure:

1. Leave the ignition switch in the ON posi-

tion for approximately 5 seconds.

2. Place the ignition switch in the OFF or

LOCK position, and wait approximately
10 seconds.

3. Repeat steps 1 and 2.

4. Restart the engine while holding the de-

vice (which may have caused the inter-
ference) separate from the registered
key.

If the no start condition re-occurs, NISSAN
recommends placing the registered key on
a separate key ring to avoid interference
from other devices.

SSD0860

Starting and driving

5-13

• Make sure the area around the vehicle is

clear.

• Check fluid levels such as engine oil, cool-

ant, brake and clutch fluid (if so equipped),
and

windshield-washer

fluid

fre-

quently as possible, or at least whenever
you refuel.

• Check that all windows and lights are

clean.

• Visually inspect tires for their appearance

and condition. Also check tires for proper
inflation.

• Lock all doors.
• Position seat and adjust head restraints/

headrests.

• Adjust inside and outside mirrors.
• Fasten seat belts and ask all passengers

to do likewise.

• Check the operation of warning lights

when the ignition switch is placed in the
ON position. For additional information,
see “Warning lights, indicator lights and
audible reminders” (P. 2-8).

1. Apply the parking brake.

Continuously Variable Transmission
model:

Move the shift lever to P (Park) or N (Neu-
tral). P (Park) is recommended.

The starter is designed not to operate
if the shift lever is in any of the driving
positions.

Manual Transmission (M/T) model:

Move the shift lever to N (Neutral). De-
press the clutch pedal to the floor.

The starter is designed not to operate
unless

the

clutch

pedal

fully

depressed.

3. Push the ignition switch to the ON posi-

tion. Depress the brake pedal and the
clutch pedal (if so equipped) and push
the ignition switch to start the engine.

To start the engine immediately, push
and release the ignition switch while de-
pressing the brake pedal with the igni-
tion switch in any position.

• If the engine is very hard to start in

extremely cold weather or when re-
starting,

depress

the

accelerator

pedal a little (approximately 1/3 to the
floor) and while holding, crank the en-

gine. Release the accelerator pedal
when the engine starts.

• If the engine is very hard to start be-

cause it is flooded, depress the accel-
erator pedal all the way to the floor
and hold it. Push the ignition switch to
the ON position to start cranking the
engine. After 5 or 6 seconds, stop
cranking

pushing

the

ignition

switch to the LOCK position. After
cranking the engine, release the accel-
erator pedal. Crank the engine with
your foot off the accelerator pedal by
depressing the brake pedal and push-
ing the ignition switch to start the en-
gine. If the engine starts, but fails to
run, repeat the above procedure.

CAUTION

Do not operate the starter for more
than 15 seconds at a time. If the engine
does not start, push the ignition switch
to the OFF position and wait 10 seconds
before cranking again, otherwise the
starter could be damaged.

BEFORE STARTING THE ENGINE

STARTING THE ENGINE

5-14

Starting and driving

Warm-up

Allow the engine to idle for at least 30
seconds after starting. Do not race the
engine while warming it up. Drive at a
moderate speed for a short distance
first, especially in cold weather. In cold
weather, keep the engine running for a
minimum of 2 - 3 minutes before shut-
ting it off. Starting and stopping the en-
gine over a short period of time may
make the vehicle more difficult to start.

5. To stop the engine, with the Intelligent

Key inside the vehicle, move the shift
lever to the P (Park) position or to N (Neu-
tral) and apply the parking brake (M/T)
and push the ignition switch to the OFF
position.

NOTE:
Care should be taken to avoid situa-
tions that can lead to potential battery
discharge and potential no-start con-
ditions such as:

1. Installation or extended use of elec-

tronic accessories that consume bat-
tery power when the engine is not
running (phone chargers, GPS, DVD
players, etc.).

2. The vehicle is not driven regularly

and/or only driven short distances.

In these cases, the battery may need to
be charged to maintain battery health.

REMOTE ENGINE START (if so
equipped)

Vehicles started with the Remote Engine
Start require the ignition switch to be
placed in the ON position before the shift
lever can be moved from the P (Park) posi-
tion. To place the ignition switch in the ON
position, follow these steps:

1. Make sure that the Intelligent Key is on

you.

2. Apply the brake.

3. Push the ignition switch once to the ON

position.

For additional information, see “NISSAN In-
telligent Key®” (P. 3-6).

CONTINUOUSLY VARIABLE
TRANSMISSION (CVT) (if so
equipped)

WARNING

•

Do not depress the accelerator pedal
while shifting from P (Park) or N (Neu-
tral) to R (Reverse), D (Drive) or L (Low)
(if so equipped). Always depress the
brake pedal until shifting is com-
pleted. Failure to do so could cause
you to lose control and have an
accident.

•

Cold engine idle speed is high, so use
caution when shifting into a forward
or reverse gear before the engine has
warmed up.

•

Do not downshift abruptly on slip-
pery roads. This may cause a loss of
control.

•

Never shift to either the P (Park) or R
(Reverse) position while the vehicle is
moving forward and P (Park) or D
(Drive) position while the vehicle is
reversing. This could cause an acci-
dent or damage the transmission.

DRIVING THE VEHICLE

Starting and driving

5-15

CAUTION

•

Except in an emergency, do not shift
to the N (Neutral) position while driv-
ing. Coasting with the transmission
in the N (Neutral) position may cause
serious damage to the transmission.

•

To avoid possible damage to your ve-
hicle, when stopping the vehicle on
an uphill grade, do not hold the ve-
hicle by depressing the accelerator
pedal. The foot brake should be used
for this purpose.

The CVT in your vehicle is electronically
controlled to produce maximum power
and smooth operation.

The recommended operating procedures
for this transmission are shown on the fol-
lowing pages. Follow these procedures for
maximum vehicle performance and driv-
ing enjoyment.

NOTE:

Engine power may be automatically re-
duced to protect the CVT if the engine
speed increases quickly when driving on
slippery roads or while being tested on
some dynamometers.

Starting the vehicle

WARNING

•

Cold engine idle speed is high, so use
caution when shifting into a forward
or reverse gear before the engine has
warmed up.

•

Do not downshift abruptly on slip-
pery roads. This may cause a loss of
control.

•

CAUTION

•

Except in an emergency, do not shift
to the N (Neutral) position while driv-
ing. Coasting with the transmission
in the N (Neutral) position may cause
serious damage to the transmission.

•

1. After starting the engine, fully depress

the foot brake pedal before moving the
shift lever out of the P (Park) position.

2. Keep the foot brake pedal depressed

and move the shift lever into a driving
gear.

3. Release the foot brake, then gradually

start the vehicle in motion.

4. Stop the vehicle completely before mov-

ing the shift lever into the P (Park)
position.

5-16

Starting and driving

The Continuously Variable Transmission
is designed so the foot brake pedal MUST
be depressed before shifting from P
(Park) to any drive position while the ig-
nition switch is in the ON position.

The shift lever cannot be moved out of P
(Park) and into any of the other gear po-
sitions if the ignition switch is placed in
the LOCK, OFF or AUTO ACC position.

To move the shift lever:

Press the button

while de-

pressing the brake pedal

Press the button

to shift

Shift without pressing the button

Shifting

After starting the engine, fully depress the
brake pedal and move the shift lever from P
(Park) to any of the desired shift positions.

WARNING

Apply the parking brake if the shift le-
ver is in any position while the engine is
not running. Failure to do so could
cause the vehicle to move unexpect-
edly or roll away and result in serious
personal injury or property damage.

If the ignition switch is placed in the OFF or
AUTO ACC position for any reason while the
vehicle is in N (Neutral), or any drive position,
the ignition switch cannot be placed in the
LOCK position. If this occurs, perform the
following steps:

1. Apply the parking brake when the ve-

hicle is stopped.

2. Move the shift lever to P (Park) to park

the vehicle and place the ignition switch
in the LOCK position.

LSD3738

Starting and driving

5-17

Nissan Sentra (2024 year). Manual in english - page 9