Nissan Kicks (2018 year). Instruction

USB/iPod® CHARGING PORTS

There are USB/iPod® charging ports lo-
cated on the center console. These ports
will charge compatible devices.

NOTE:

The USB/iPod® charging ports will not
operate with the display screen. Only the
USB connection port located on the in-
strument panel, below the temperature
controls, will operate USB/iPod® devices
through the audio system.

ANTENNA

The rod antenna cannot be shortened, but
can be removed. When you need to remove
the antenna, turn the antenna rod counter-
clockwise

䊊

To install the antenna rod, turn the antenna
rod clockwise

䊊

and hand tighten.

CAUTION

To avoid damaging or deforming the
antenna, be sure to remove the antenna
under the following conditions.

∙ The vehicle enters an automatic car

wash.

∙ The vehicle enters a garage with a low

ceiling.

∙ The vehicle is covered with a car cover.

∙ Always properly tighten the antenna

rod during installation or the antenna
rod

may

break

during

vehicle

operation.

LHA4725

LHA4236

4-64

Monitor, climate, audio, phone and voice recognition systems

Apple Siri® Eyes Free personal assistant
can be accessed from the vehicle. Siri Eyes
Free can be accessed in Siri Eyes Free
mode to reduce user distraction. In this
mode, Siri Eyes Free is available for interac-
tion by voice control. After connecting a
compatible

Apple

device

using

Bluetooth®, Siri Eyes Free can be activated
from the

button on the steering

wheel.
Siri® is a trademark of Apple Inc., registered
in the U.S. and other countries.

∙ Some Siri Eyes Free functions, such as

displaying pictures or opening apps,
may not be available while driving.

∙ For getting best results, always update

your device to the latest software ver-
sion.

∙ Keep the interior of the vehicle as quiet

as possible. Close the windows to elimi-
nate the surrounding noises (traffic
noises, vibration sounds, etc.), which
may prevent the system from recogniz-
ing the voice commands correctly.

∙ For functions that can be used in Siri

Eyes Free, please refer to the Apple
website.

REQUIREMENTS

Siri is only available on the iPhone® 4S or
later. Devices released before iPhone® 4S
are not supported by the Siri Eyes Free sys-
tem. Visit www.apple.com/ios/siri for de-
tails about device compatibility.

Siri must be enabled on the phone. Please
check phone settings.

If the device has a lock screen, Siri must be
accessible from the lock screen. Please
check phone settings.

For best results, always update your device
to the latest software version.

OPERATING SIRI® EYES FREE

1. Push

button for less than 1.5 sec-

onds.

2. Speak your command and then listen

to the Siri® Eyes Free reply.

After starting Siri Eyes Free, push the
button again within 5 seconds of the end of
the Siri Eyes Free announcement to extend
the session.

LHA4733

SIRI® EYES FREE (if so equipped)

Monitor, climate, audio, phone and voice recognition systems

4-65

Example 1 – Playing music

1. Push

button for less than 1.5 sec-

onds.

2. Say “Play (artist name, song name,

etc.)”.

3. Your vehicle will automatically change

to Bluetooth® Audio or iPod® mode*
when the music starts playing. Mode
selection is determined by the phone.

* If the iPhone® is also connected with the
USB cable.

If the audio track does not start playing
automatically after Siri Eyes Free ends, try
changing the track or audio source to re-
sume playback.

NOTE:

For best results, use the native music
app. Performance of music control func-
tion while using Podcasts, Audiobook or
other 3rd party music apps may vary and
is controlled by the iPhone®.

Example 2 – Replying to text messages

1. If a compatible iPhone® is connected

and “Show Notifications” of the iPhone®
settings is enabled, the vehicle will dis-
play a notification for new incoming
text messages.

2. After reading the message, push or

push and hold the

button to reply

using Siri Eyes Free.

3. After a beep sounds, say “Text mes-

sage” or a similar command to reply
using Siri Eyes Free.

4-66

Monitor, climate, audio, phone and voice recognition systems

TROUBLESHOOTING GUIDE

Symptom

Cause and Countermeasure

Cannot access Siri Eyes
Free from switch on the
steering wheel

Check if a Bluetooth® connection is established between the iPhone® and the system.

Check if Siri is enabled on the device. On your phone, go to Siri setting.

Check that Siri can be accessed from the device lock screen. This can be set in the settings menu of your phone.

Audio Source does not
change automatically to
iPod® or Bluetooth® Au-
dio mode

For best results, use the native Music app. Performance of music control function while using Podcasts, Audiobook or other 3rd party
music apps may vary.

For best results, play media already stored on your device. Streaming music or playback from cloud storage may degrade
performance.

Switch the source manually by pressing the AUX or MEDIA button on the vehicle audio system or the SOURCE select switch on the
steering wheel.

Play, pause, next track,
previous track or play
timer does not work

For best results, use the native Music app. Performance of music control function while using Podcasts, Audiobook or other 3rd party
music apps may vary and is controlled by the device.

Cannot hear any music/
audio being played back
from a connected
iPhone®

Check that the audio source is set to Bluetooth® Audio or iPod® mode. A USB connection is required for iPod® mode.

Cannot receive text mes-
sage notifications on the
vehicle audio system

Check if “Send Notifications” is enabled on your phone. On the phone, go to Bluetooth® settings. Find the device name, like “My Car”.
Press the INFO button. Turn on “Show Notifications”.

Cannot reply to text
message notifications by
Siri Eyes Free

After receiving an incoming text message, follow on-screen guidance. Push the

button for 1.5 seconds on the steering wheel

for Siri Eyes Free. After Siri Eyes Free starts, say “Text Message”.

Monitor, climate, audio, phone and voice recognition systems

4-67

When installing a CB, ham radio or car
phone in your vehicle, be sure to observe
the following precautions; otherwise, the
new equipment may adversely affect the
engine control system and other electronic
parts.

WARNING

∙ A cellular phone should not be used

for any purpose while driving so full
attention may be given to vehicle op-
eration. Some jurisdictions prohibit
the use of cellular phones while
driving.

∙ If you must make a call while your ve-

hicle is in motion, the hands free cellu-
lar phone operational mode (if so
equipped) is highly recommended.
Exercise extreme caution at all times
so full attention may be given to ve-
hicle operation.

∙ If you are unable to devote full atten-

tion to vehicle operation while talking
on the phone, pull off the road to a
safe location and stop your vehicle.

CAUTION

∙ Keep the antenna as far away as pos-

sible

from

the

electronic

control

modules.

∙ Keep the antenna wire more than 8 in

(20 cm) away from the electronic con-
trol system harnesses. Do not route
the antenna wire next to any harness.

∙ Adjust the antenna standing-wave

ratio

recommended

the

manufacturer.

∙ Connect the ground wire from the CB

radio chassis to the body.

∙ For additional information, it is rec-

ommended that you visit a NISSAN
dealer.

WARNING

∙ Use a phone after stopping your ve-

hicle in a safe location. If you have to
use a phone while driving, exercise ex-
treme caution at all times so full at-
tention may be given to vehicle
operation.

∙ If you are unable to devote full atten-

tion to vehicle operation while talking
on the phone, pull off the road to a
safe location and stop your vehicle.

CAUTION

To avoid discharging the vehicle bat-
tery, use a phone after starting the
engine.

CAR PHONE OR CB RADIO

BLUETOOTH® HANDS-FREE PHONE
SYSTEM

4-68

Monitor, climate, audio, phone and voice recognition systems

Your

NISSAN

equipped

with

the

Bluetooth® Hands-Free Phone System. If
you have a compatible Bluetooth® enabled
cellular phone, you can set up the wireless
connection between your cellular phone
and the in-vehicle phone module. With
Bluetooth® wireless technology, you can

make or receive a hands-free telephone
call with your cellular phone in the vehicle.

Once your cellular phone is connected to
the in-vehicle phone module, no other
phone connecting procedure is required.
Your phone is automatically connected

with the in-vehicle phone module when
the ignition switch is placed in the ACC or
ON position with the previously connected
cellular phone turned on and carried in the
vehicle.

NOTE:

Some devices require the user to accept
connections to other Bluetooth® de-
vices. If your phone does not connect au-
tomatically to the system, consult the
phone’s Owner’s Manual for details on
device operation.

You can connect up to six different
Bluetooth® cellular phones to the in-
vehicle phone module. However, you can
talk on only one cellular phone at a time.

Before using the Bluetooth® Hands-Free
Phone System, refer to the following notes.

∙ Set up the wireless connection be-

tween a compatible cellular phone and
the in-vehicle phone module before us-
ing the hands-free phone system.

LHA4699

Monitor, climate, audio, phone and voice recognition systems

4-69

∙ Some

Bluetooth®

enabled

cellular

phones may not be recognized or work
properly.

Please

visit

www.nissanusa.com/bluetooth

www.nissan.ca/bluetooth for a recom-
mended phone list and connecting in-
structions.

∙ You will not be able to use a hands-free

phone under the following conditions:

– Your vehicle is outside of the cellular

service area.

– Your vehicle is in an area where it is

difficult to receive a cellular signal;
such as in a tunnel, in an under-
ground parking garage, near a tall
building or in a mountainous area.

– Your cellular phone is locked to pre-

vent it from being dialed.

∙ When the radio wave condition is not

ideal or ambient sound is too loud, it
may be difficult to hear the other per-
son’s voice during a call.

∙ Do not place the cellular phone in an

area surrounded by metal or far away
from the in-vehicle phone module to
prevent tone quality degradation and
wireless connection disruption.

∙ While a cellular phone is connected

through the Bluetooth® wireless con-
nection, the battery power of the cellu-
lar phone may discharge quicker than
usual.

The

Bluetooth®

Hands-Free

Phone System cannot charge cellular
phones.

∙ Some cellular phones or other devices

may cause interference or a buzzing
noise to come from the audio system
speakers. Storing the device in a differ-
ent location may reduce or eliminate
the noise.

∙ For additional information, refer to the

cellular phone Owner’s Manual regard-
ing the telephone charges, cellular
phone antenna and body, etc.

REGULATORY INFORMATION

FCC Regulatory information

– CAUTION: To maintain compliance with

FCC’s RF exposure guidelines, use only
the supplied antenna. Unauthorized an-
tenna,

modification,

attachments

could damage the transmitter and may
violate FCC regulations.

– Operation is subject to the following two

conditions:

1. This device may not cause interference

and

2. this device must accept any interfer-

ence, including interference that may
cause undesired operation of the de-
vice.

IC Regulatory information

– Operation is subject to the following two

conditions: (1) this device may not cause
interference, and (2) this device must ac-
cept any interference, including interfer-
ence that may cause undesired opera-
tion of the device.

– This Class B digital apparatus meets all

requirements

the

Canadian

Interference-Causing Equipment Regu-
lations.

BLUETOOTH® is a
trademark owned
by Bluetooth SIG,
Inc. and licensed
to Visteon.

4-70

Monitor, climate, audio, phone and voice recognition systems

USING THE SYSTEM

The system allows hands-free operation of
the Bluetooth® Hands-Free Phone System.

If the vehicle is in motion, some commands
may not be available so full attention may
be given to vehicle operation.

Initialization

When the ignition switch is placed in the ON
position, NISSAN Voice Recognition is initial-
ized,

which

takes

few

seconds.

the

button is pressed before the ini-

tialization completes, the system will an-
nounce “There is no phone connected” and
will not react to voice commands.

Operating tips

To get the best performance out of the
NISSAN Voice Recognition System, observe
the following:

∙ Keep the interior of the vehicle as quiet

as possible. Keep all vents pointed away
from the microphone and close the
windows

eliminate

surrounding

noises (traffic noises, vibration sounds,
etc.), which may prevent the system
from recognizing voice commands cor-
rectly.

∙ Wait until the tone sounds before

speaking a command. Otherwise, the
command will not be received properly.

∙ Start speaking a command within

5 seconds after the tone sounds.

∙ Speak in a natural voice without paus-

ing between words.

∙ For calling contacts by name, please

say both the first and last name of the
contact for better recognition.

Giving voice commands

To operate NISSAN Voice Recognition,
press the

button located on the

steering wheel for more than 1.5 seconds.
After the tone sounds, speak a command.
The command given is picked up by the
microphone, and voice feedback is given
when the command is accepted.

∙ If a command is not recognized, the

system announces, “Please say or se-
lect a command from the displayed list.”
Make sure the command is said exactly
as prompted by the system and repeat
the command in a clear voice.

∙ If you want to go back to the previous

command, you can say “Go back” or
“Correction” any time the system is
waiting for a response.

∙ You can cancel a command when the

system is waiting for a response by say-
ing, “Cancel” or “Quit.” The system an-
nounces “Exit” and ends the Voice Rec-
ognition session. You can also press
and hold the

button on the steer-

ing wheel for 1.5 seconds at any time to
end the Voice Recognition session.
Whenever the Voice Recognition ses-
sion is canceled, a double beep is
played to indicate you have exited the
system.

∙ If you want to adjust the volume of the

voice feedback, push the (+ or -) volume
control switches on the steering wheel
while being provided with feedback. You
can also use the radio volume control
knob.

Voice Prompt Interrupt
In most cases you can interrupt the voice
feedback to speak the next command by
pressing the

button on the steering

wheel. After interrupting the system, wait
for a beep before speaking your command.

Monitor, climate, audio, phone and voice recognition systems

4-71

INDICATORS

When

cellular

phone

connected

through the Bluetooth® wireless connec-
tion, indicators

䊊

for the phone and text

messaging are displayed on the top of the
screen.

Indicator

Description

Indicates there are un-
read received
messages.

Indicates the
Bluetooth® device that
is currently connected.

Indicates the strength
of the signal the
Bluetooth® device is
receiving.

Indicates the amount
of remaining
Bluetooth® device
battery.

CONTROL BUTTONS

The control buttons for the Bluetooth®
Hands-Free Phone System are located on
the steering wheel.

LHA4723

LHA4684

4-72

Monitor, climate, audio, phone and voice recognition systems

VOICE COMMAND BUTTON

Press and hold the

but-

ton for more than 1.5 seconds
to initiate the Voice Recogni-
tion session. To exit the Voice
Recognition session press

and hold the

for more

than 1.5 seconds. For addi-
tional information, refer to
“Voice prompt interrupt” in
this section.

You can use the

button

to interrupt the system feed-
back and give a command at
once.

If an iPhone® is connected,
Siri® can be accessed by

pressing the

button for

less than two seconds. For
additional information, refer
to “Siri® Eyes Free” in this
section.

PHONE BUTTON
To answer an incoming call or
to end a call press

the

button.

To reject a call press and hold

the

button.

CONNECTING PROCEDURE

NOTE:

The connecting procedure must be per-
formed when the vehicle is stationary. If
the vehicle starts moving during the pro-
cedure, the procedure will be canceled.

LHA4726

Monitor, climate, audio, phone and voice recognition systems

4-73

To connect a phone to the Bluetooth®
Hands-Free Phone System:

Manual Connecting Procedure

1. Press the

MENU button on the

control panel.

2. Touch the “Connections” key on the

screen.

3. In the Bluetooth tab, touch the “Add

New” key to connect a phone.

4. When a compatible phone is found a

message with a PIN appears on the
screen.

5. Verify the PIN is correct and accept the

connection.

6. To access the Bluetooth® settings

menu touch the “

” key on the Con-

nections screen. The following options
are available:

Menu Item

Result

Bluetooth

Allows user to switch Bluetooth® on and off. Bluetooth® must be turned on in order to connect a device.

Turns Bluetooth® functionality on. To turn off, touch the “ON” key again. The indicator light will go off.

Favorite (Connection first)

Allows user to toggle “Phone” and “Audio” favorite settings on and off.

Allows user to customize the PIN to a four digit number.

4-74

Monitor, climate, audio, phone and voice recognition systems

NOTE:

Some cellular phones may require you to
accept certain permissions in order to
enable features on your Bluetooth® sys-
tem. During the Bluetooth® pairing pro-
cess, please check your cellular phone’s
display for a pop-up with the request to
grant phonebook access.
Granting phonebook access permission
will allow your contacts to be down-
loaded to the vehicle’s Bluetooth® sys-
tem. A pop-up may display on your cellu-
lar phone stating that the contacts and
call history. Please select “Allow” or Yes”
to grant this permission.

Automatic Connecting Procedure

If no phone is connected to the system,
press and hold the

button on the

steering wheel for more than 1.5 seconds.
After the prompt, speak “Add Phone”, the
system will announce “transferring to the
add phone settings menu”. The system will
start the pairing procedure. When a com-
patible phone is found, a message with a
PIN appears on the screen. Operate the
Bluetooth® phone to complete the con-
nection process. For additional informa-
tion, refer to “Bluetooth® connections
screen” in this section.

VOICE COMMANDS

Voice commands can be used to operate
the Bluetooth® Hands-Free Phone System.
Press and hold the

button for more

than 1.5 seconds to bring up the phone
command menu. The commands avail-
able are:

∙ Call <name>

∙ Dial <number>

∙ Recent Calls

∙ Read/Send Text (if so equipped)

∙ Siri® (if so equipped)

∙ Voice Assistant (if so equipped)

∙ Phonebook

∙ Quick Dial

∙ Redial

∙ Select Phone

∙ Add Phone

∙ Call <name> Mobile

∙ Call <name> Home

∙ Call <name> Office

∙ Call <name> Main

∙ Call <name> Other

∙ Settings

“Call <name>”

Speak this command to make a call to a
contact that is stored in the phonebook.
Say “Call” followed by a phonebook name to
initiate a call. If the system does not recog-
nize the name it will display a list of similar
names. After the prompt, speak or touch
an item number from the displayed list to
place the call.

“Dial <number>”

Speak this command to make a call with a
spoken phone number. After the prompt,
say “Dial” followed by a 7 to 10 digit phone
number. The system will repeat the num-
ber back. Say “Dial” to initiate the call or
“Correction” to re-enter the phone number.

Monitor, climate, audio, phone and voice recognition systems

4-75

“Recent Calls”

The following commands are available un-
der “Recent Calls”:

∙ Incoming Calls

Speak this command to list the last
20 incoming calls to the vehicle. If the
call is from an entry in the phonebook,
the name will be displayed. Otherwise,
the phone number of the incoming call
will be displayed.
When prompted, speak or touch the
item number on the screen to place the
call. Select the “Next” key to move
through the list of incoming calls.

∙ Outgoing Calls

Speak this command to list the last 20
outgoing calls from the vehicle. If the
call was to an entry in the phonebook,
the name will be displayed. Otherwise,
the phone number of the outgoing call
will be displayed.
When prompted, speak or touch the
item number on the screen to place the
call. Select the “Next” key to move
through the list of outgoing calls.

∙ Missed Calls

Speak this command to list the last 20
missed calls to the vehicle. If the call is
from an entry in the phonebook, the
name will be displayed. Otherwise, the
phone number of the missed call will be
displayed.
When prompted, speak or touch the
item number on the screen to place the
call. Select the “Next” key to move
through the list of missed calls.

“Read Text/Send Text” (if so
equipped)

Speak this command to access text mes-
saging functions. For additional informa-
tion, refer to “Text messaging” in this sec-
tion.

“Phonebook through voice
command”

Speak “Phonebook” to view a list of quick
steps to access entries stored in the
phonebook. Commands are organized by
the phone number type selected in the cel-
lular device. For additional information, re-
fer to the cellular phone’s owner’s manual.

The following commands are available:

∙ <Say a Contact Name>

∙ <Say a Contact Name> Main

∙ <Say a Contact Name> Home

∙ <Say a Contact Name> Mobile

∙ <Say a Contact Name> Office

∙ <Say a Contact Name> Other

For additional information on manually se-
lecting phonebook entries, refer to “Making
a call” in this section.

“Quick dial”

Speak this command to access the Quick
dial menu. After the prompt, speak or se-
lect an item number on the displayed list to
place the call. For additional information,
refer to “Making a call” in this section.

“Redial”

Speak this command to call the last num-
ber dialed. After the prompt, say “Redial” to
dial the number of the last outgoing call.
The

system

will

display

“Redialing

<name/number>”.

The

name

the

phonebook entry will be displayed if it is
available, otherwise the number being re-
dialed will be displayed.

4-76

Monitor, climate, audio, phone and voice recognition systems

“Select Phone”

Speak this command to access the Con-
nections menu. For additional information,
refer to “Bluetooth® connections screen” in
this section.

“Add Phone”

Speak this command to access the Con-
nections menu. For additional information,
refer to “Bluetooth® connections screen” in
this section.

“Settings”

Speak this command to access the Sys-
tem Voice settings menu. The system will
exit Voice Recognition mode. Touch one of
the following options on the screen to
change the settings.

∙ Beep Only for Opening Prompt

By touching the “ON” key, the indicator
light will illuminate, the system voice will
turn off and only a tone will sound when
the Bluetooth® Hands-Free Phone Sys-
tem is activated. To turn the system
voice back on, touch the “ON” key again,
the indicator light will turn off.

∙ Best Match List

When the system doesn’t recognize a
phonebook name it will provide a list of
similar sounding names. To turn this off,
touch the “ON” button, the indicator
light will turn off. To turn on, touch the
“ON” key again, the indicator light will
turn on.

PHONE DISPLAY SCREEN

The Phone screen can be displayed by
pressing the

button on the control

panel.
The following options are displayed:

∙ Quick Dial

Displays the Quick Dial screen. For addi-
tional information, refer to “Quick dial” in
this section.

∙ Phonebook

Displays the Phonebook screen. For ad-
ditional information, refer to “Making a
call” in this section.

LHA4705

Monitor, climate, audio, phone and voice recognition systems

4-77

∙ Call History

Displays the Call History screen. For ad-
ditional information, refer to “Making a
call” in this section.

∙ Dial Number

Displays the Dial Number screen. For
additional information, refer to “Making
a call” in this section.

∙ Text Message

Displays the received message screen.
For additional information, refer to “Text
messaging” in this section.

∙ Connections

Displays the Connections screen. For
additional

information,

refer

“Bluetooth® connections screen” in this
section.

∙ Volume

Displays

the

volume

adjustment

screen. For additional information, refer
to “Volume & beeps” in this section.

MAKING A CALL

To make a call press the

button on

the control panel. Touch an option from
menu screen:

∙ Phonebook

Select a person and the phone number
you wish to call from the phonebook.
Depending on the device, the phone-
book will be downloaded from the cel-
lular phone automatically when it is
connected. If the automatic download
does not take place, the phone number
must be transferred to the hands-free
phone system from the cellular phone
prior to using this method. For addi-
tional information, refer to “Phone and
text message settings” in this section.

∙ Call History

Select a phonebook name or phone
number from the recent incoming, out-
going or missed calls tabs. Touch a
phonebook name or phone number
listed to initiate the call.

∙ Dial Number

Enter the phone number manually us-
ing the keypad displayed on the screen.
Press the “OK” key on the screen to initi-
ate the call.

For additional options to make a call, refer
to “Voice commands” in this section.

Quick Dial

Quick Dial entries can be used to quickly
make a call. The system allows up to 20
entries to be stored. To set up a quick dial
press the

button on the control

panel. Touch the “Quick Dial” key to display a
list of quick dial entries. Touch the “Edit” key
to edit current entries or touch the “Add
New” key to make a new entry. Two meth-
ods are given to create a quick dial entry:

∙ Touch the “Copy from Call History” key

to save a phone number from the In-
coming, Outgoing or Missed call history
lists. Select the person or phone num-
ber from the menu to be added. A reg-
istration menu will display the Entry #,
phone number, phone number type
stored in the cellular phone and Voice
Tag. Select the “OK” key.

4-78

Monitor, climate, audio, phone and voice recognition systems

∙ Touch the “Copy from Phonebook” key

to save a number from the phonebook.
Use the scroll keys on the side to move
up and down through the menu. Select
a person to be added. A menu will dis-
play the Entry #, phone number, phone
number type stored in the cellular
phone and Voice Tag. Select the “OK”
key.

Voice tag

A voice tag can be recorded for each of the
registered Quick Dial numbers and can be
used to dial the number by speaking it. On
the Quick Dial registration screen, touch
the “Voice Tag” key. Select a relationship
from the list or create a new voice tag. To
record a new voice tag touch the “Custom-
ize” key on the screen then touch the “Store”
key. Speak a name after the prompt, the
new tag will be stored. To edit or create a
new voice tag select the “Customize” key
again. Touch the “Play” key to play the re-
corded voice tag, touch the “Restore” key to
edit the voice tag or “Delete” to delete the
current voice tag.

RECEIVING A CALL

When a call is received by the phone con-
nected to the vehicle’s Bluetooth® Hands-
Free Phone System, the call information is
displayed on the control panel display.

Press the

button on the steering

wheel or touch the “

Answer” key on

the screen to accept the call. To reject the
call touch the “

Decline” key on the

screen.
If the user is not able to answer the call
right away, touch the “Hold Call” key dis-
played on the screen. A message will be
played for the caller: “I’m not able to take a
call right now.” The user may then accept
the call when available or reject the call.

To reject a call, press and hold the
button on the steering wheel.

DURING A CALL

While a call is active the following options
will appear on the control panel display:

∙ Mute

Touch this key to mute or unmute the
system.

∙ Dial Number

Touch this key to dial digits during the
phone call.

∙ Use Handset

Touch this key to transfer the call to the
handset. To transfer the call back from
the handset to the Bluetooth® Hands-
Free Phone System, press the
button on the control panel then select
the “Transfer Hands-free” key on the
screen.

∙ Switch Call

This option will only be available when a
second call is active.

supported

the

phone,

the

Bluetooth® Hands-Free Phone System
allows for call waiting functionality. If a
call is received while another call is al-
ready active, a message will be dis-
played on the screen. Press the
button on the steering wheel or touch
the “

Answer” key on screen to ac-

cept the incoming call. Touch the
“

Decline” key on the screen to re-

ject the second call.

Monitor, climate, audio, phone and voice recognition systems

4-79

Nissan Kicks (2018 year). Instruction - part 16