Nissan 370Z (2018 year). Instruction

language setting.
Scroll direction:
Set the scrolling behavior of the TUNE/

MENU knob to scroll UP or DOWN.

FM·AM radio operation

The audio system operates when the

ignition switch is in the “ACC” or “ON”

position.

FM·AM button:

When the FM·AM button is pushed while

the audio system is off, the audio system

will turn on and the radio will turn on.

When the FM·AM button is pushed while

another audio source is already operat-

ing, it will automatically turn off, and the

radio will turn on.
To change the radio bands, push the

FM·AM button until the desired band

appears.
AM

? FM 1 ? FM 2 ? AM

TUNE/MENU knob:
When adjusting the broadcasting station

frequency manually, turn the TUNE/MENU

knob until the preferred frequency is

achieved.

Seek tuning button:

When adjusting the broadcasting station

frequency automatically, push the

button. When the system detects a

broadcasting station, it will stop at the

station.

Radio memory buttons:

During radio reception, pushing the radio

memory button for less than 2 seconds

will select the stored radio station.
The audio system can store up to 12 FM

station frequencies (six in each of FM 1and

FM 2) and 6 AM station frequencies.
To store the station frequency manually:
1. Tune to the desired broadcasting

station frequency by using the

button.

2. Push and hold a radio memory button

until a beep sounds. (The radio

mutes when the radio memory button

is pushed.)

3. The channel indicator will display and

the radio mute disengages, indicating

that the memory is stored properly.

4. Perform steps 1 - 3 for all other

memory buttons.

If the battery cable is disconnected, or if

the audio fuse blows, the radio memory

will be erased. In such a case, reset the

desired stations.

SCAN button:

Push the SCAN button to tune from low

to high frequencies and stops at each

broadcasting station for 5 seconds. Push-

ing the SCAN button again during this 5

seconds period will stop SCAN tuning and

the radio will remain tuned to that

station.
If the SCAN button is not pushed within 5

seconds, SCAN tuning moves to the next

station.

CD player operation

The audio system operates when the

ignition switch is in the “ACC” or “ON”

position.
Loading:
Insert a CD into the slot with the label side

facing up. The CD will be guided auto-

matically into the slot and will start

playing. After loading the CD, the number

of tracks and the playtime will appear on

the display.

CAUTION

Do not force the CD into the slot. This

could damage the player.

Center display, heater, air conditioner, audio, phone and voice recognition systems

4-45

4-46

Center display, heater, air conditioner, audio, phone and voice recognition systems

NOTE:

. The CD player accepts normal audio

CDs or CDs containing MP3/WMA

files.

. The audio unit will automatically

detect if a CD containing MP3/WMA

files is inserted, and “MP3CD” will be

indicated.

. An error notification message will be

displayed when inserting an incom-

patible disc type (e.g. DVD), or if the

player cannot read the CD. Eject the

disc and insert another disc.

List view:
While the track is being played, push

either the ENTER button or the back

button to display the available tracks in

a listed view mode. To select a track from

the list, or a track to start listening to, turn

the TUNE/MENU knob then push the

ENTER button.
Quick search:
In the list view mode, a quick search can

be performed to find a track from the list.

Push the A-Z button, turn the TUNE/

MENU knob to the first alphabetic letter

of the song title and then push the ENTER

button. When found, a list of the available

songs will be displayed. Select, and push

the ENTER button to play the preferred

track.

CD button:

When the CD button is pushed while the

audio system is off and a CD is loaded, the

audio system will turn on and a CD will

start playing automatically. If another

audio source is already playing, it will

automatically turn off and the CD will

start playing.

Fast Forward/Rewind but-

tons:
Push and hold the

button to

fast forward or rewind through the track.

When the button is released, the track will

play at normal playing speed.
Track up/down:
Pushing the

button once, the

track will skip forward to the next track or

backward to the beginning of the current

track. Push the

button more

than once to skip through the tracks.
Folder browsing:
If the recorded media contains folders

with music files, pushing the

button will play in sequence the tracks of

each folder.
To select a preferred folder:
1. Push the ENTER button or the back

button and a list of tracks in the

current folder is displayed.

2. Push the back button.
3. Turn the TUNE/MENU knob for the

preferred folder.

4. Push the ENTER button to access the

folder. Push the ENTER button again

to start playing the first track or turn

the TUNE/MENU knob, and push the

ENTER button to select another track.

If the current selected folder contains sub

folders, push the ENTER button, a new

screen with a list of sub folders will be

displayed. Turn the TUNE/MENU knob for

the sub folder then push the ENTER

button to select. Select the root folder

item when songs are recorded addition-

ally in the root folder.
To return to the previous folder screen,

push back button.

RPT button:

Push the RPT button and the current

track will be played continuously.

RDM button:

Push the RDM button and all the tracks

will be played in a random order.

DISP button:

While a CD with recorded music informa-

tion tags (CD-text/ID3-text tags) is being

played, the title of the played track is

displayed. If the title information is not

provided then “Track” is displayed.
When the DISP button is pushed repeat-

edly, further information about the track

can be displayed along with the track title

as follows:
CD:
Track time

? Album ? Artist ? Track

time
CD with MP3/WMA:
Track time

? Album ? Artist ? Folder

name

? Track time

Track details:
Pushing and holding the DISP button will

turn the display into a detailed overview

and after a few seconds it returns to the

main display.

button:

When the SCAN button is pushed while a

CD is being played, the first 10 seconds of

all the tracks will be played.
When the SCAN button is pushed again,

the CD will return to normal play from the

track which is playing.

CD eject button:

When the CD eject button is pushed while

a CD is loaded, the CD will be ejected.
When the CD eject button is pushed twice,

the CD will be ejected further, and the CD

can be removed with ease.
When the ignition switch is in the “OFF” or

“LOCK” position it is possible to eject the

CD currently being played. However the

audio unit will not be activated.
If a CD is ejected by pushing the CD eject

button, and it is not taken out from the

loading slot within 8 seconds, the CD will

automatically be reloaded to the slot to

protect the CD.

JVH0920X

USB (Universal Serial Bus) connec-

tion port

Connecting USB device:
The USB connection port is located in the

center console. Open the console box lid

and connect a USB memory device into

the USB connection port. The system

switches to the USB mode automatically.
If the system has been turned off while

the USB memory device was playing,

pushing the power button will start play-

back of the USB memory device.

Center display, heater, air conditioner, audio, phone and voice recognition systems

4-47

4-48

Center display, heater, air conditioner, audio, phone and voice recognition systems

WARNING

Do not connect, disconnect or oper-

ate the USB device while driving.

Doing so can be a distraction. If

distracted you could lose control of

your vehicle and cause an accident

or serious injury.

CAUTION

. Do not force the USB device into

the USB connection port. Insert-

ing the USB device tilted or up-

side-down into the port may da-

mage the port. Make sure that

the USB device is connected cor-

rectly into the USB connection

port. (Some USB devices come

with a

mark as a guide. Make

sure that the mark is facing the

correct direction before inserting

the device.)

. Do not leave the USB cable in a

place where it can be pulled

unintentionally. Pulling the cable

may damage the port.

Refer to your device manufacturer’s own-

er information regarding the proper use

and care of the device.

USB button:

When the USB button is pushed with the

system off and the USB memory device is

inserted, the system will turn on.
USB device main operation:
The following operations are identical to

the audio main operation of the Compact

Disc (CD) operation. For details, see “CD

player operation” (P.4-45).
. List view

. Quick search

. RDM (Random play)

. RPT (Repeat track)

. SCAN

. Folder browsing

DISP button:

While a track with recorded music infor-

mation tags (ID3-tags) is being played, the

title of the played track is displayed. If the

tags are not provided then a notification

message is displayed.
When the DISP button is pushed repeat-

edly, further information about the track

can be displayed along with the track title

as follows:
Track time

? Artist ? Album ? Folder

name

? Track time

Track details:
Pushing and holding the DISP button will

turn the display into a detailed overview

and after a few seconds it returns to the

main display, or push the DISP button

briefly.

JVH0921X

iPod® player operation

Connecting iPod®:
The USB connection port is located in the

center console. Open the console box lid

and connect the iPod® cable to the USB

connection port. The battery of the iPod®

is charged while the connection to the

vehicle.
Depending on the version of the iPod®,

the display on the iPod® shows a NISSAN

or Accessory Attached screen when the

connection is completed. When the iPod®

is connected to the vehicle, the iPod®

music library can only be operated by the

vehicle audio controls.

WARNING

Do not connect, disconnect or oper-

ate the USB device while driving.

Doing so can be a distraction. If

distracted you could lose control of

your vehicle and cause an accident

or serious injury.

CAUTION

. Do not force the USB device into

the USB connection port. Insert-

ing the USB device tilted or up-

side-down into the port may da-

mage the port. Make sure that

the USB device is connected cor-

rectly into the USB connection

port. (Some USB devices come

with a

mark as a guide. Make

sure that the mark is facing the

correct direction before inserting

the device.)

. Do not leave the USB cable in a

place where it can be pulled

unintentionally. Pulling the cable

may damage the port.

Refer to your device manufacturer’s own-

er information regarding the proper use

and care of the device.
Compatibility:
The following models are supported:
. Third generation iPhone® (Firmware

version IOS4/4.0)

. Fourth generation iPhone® (Firmware

version IOS4/4.0)

. Fifth generation iPod® (Firmware ver-

sion 1.3)

. First generation iPod Classic® (Firm-

ware version 1.1.1 or 1.1.2PC)

. Second generation iPod Classic®

(Firmware version 2.0.1)

. First generation iPod touch® (Firm-

ware version 1.1.5 or 2.2.1)

. Second and third generation iPod

touch® (Firmware version 2.2.1 or

IOS4/4.0.0)

. First generation iPod nano® (Firmware

version 1.3.1)

. Second generation iPod nano® (Firm-

ware version 1.1.3)

. Third generation iPod nano® (Firm-

ware version 1.1.2PC or 1.1.3PC)

. Fourth generation iPod nano® (Firm-

ware version 1.0.2 or 1.0.4)

. Fifth generation iPod nano® (Firmware

version 1.0.1 or 1.0.2)

Center display, heater, air conditioner, audio, phone and voice recognition systems

4-49

4-50

Center display, heater, air conditioner, audio, phone and voice recognition systems

The iPod touch® may not response

quickly with the system in some cases.
Make sure that the iPod® firmware is

updated.
Operating tips:
. iPod Shuffle® and iPod mini® are not

supported.

. Some iPod® operations may not be

available with this system.

USB button:

When the USB button is pushed with the

system off and the iPod® is connected to

the vehicle, the system will turn on.
iPod® main operation:
Interface:
The interface for iPod® operation shown

on the audio system display is similar to

the iPod® interface. Use the TUNE/MENU

knob to play a track on the iPod®.
The following items can be chosen from

the menu list screen.
. Playlists

. Artists

. Albums

. Tracks

. Genres
For further information about each item,

see the iPod® owner’s manual.

The following operations are identical to

the audio main operation of the Compact

Disc (CD) operation. For details, see “CD

player operation” (P.4-45).
. List view

. Quick search

. RDM (Random play)

. RPT (Repeat track)

. Folder browsing

DISP button:

While a track with recorded music infor-

mation tags (ID3-tags) is being played, the

title of the played track is displayed. If the

tags are not provided then a notification

message is displayed.
When the DISP button is pushed repeat-

edly, further information about the track

can be displayed along with the track title

as follows:
Track time

? Album ? Artist ? Genre ?

Track time
Track details:
Pushing and holding the DISP button will

turn the display into a detailed overview

and after a few seconds it returns to the

main display, or push the DISP button

briefly.

JVH0936X

AUX (Auxiliary) input

AUX IN jack:
The AUX IN jack is located in the center

console. The AUX IN audio input jack

accepts any standard analog audio input

such as from a portable cassette tape/CD

player, MP3 player or laptop computer.
NISSAN strongly recommends using a

stereo mini plug cable when connecting

your music device to the audio system.

Music may not play properly when a

monaural cable is used.

4-52

Center display, heater, air conditioner, audio, phone and voice recognition systems

SAA2495

DVD·CD EJECT button

ON·OFF button/VOL (volume) control

knob

Radio station preset select buttons

DISC·AUX (auxiliary) button

Radio TUNE (tuning) folder selector/

AUDIO control knob

Radio SCAN tuning button

FM·AM band select button

RPT (repeat)/RDM (random) play button

SAT (satellite) button

10.

Radio CAT (category)/REW (rewind) but-

ton for SEEK/TRACK

11.

FF (fast forward) button for SEEK/TRACK

FM-AM-SAT RADIO WITH COMPACT

DISC (CD) PLAYER

For all operation precautions, see “Audio

operation precautions” (P.4-30).
The satellite radio mode requires an

active SiriusXM Satellite Radio subscrip-

tion. The satellite radio is not available in

Alaska, Hawaii and Guam.
It may take some time to receive the

activation signal after subscribing the

SiriusXM Satellite Radio. After receiving

the activation signal, an available channel

list will be automatically updated in the

radio. Push the ignition switch from LOCK

to ACC to update the channel list.

Audio main operation

Head unit:
The auto loudness circuit enhances the

low and high frequency ranges automa-

tically in both radio reception and CD

playback.
ON·OFF/Volume control:
Push the ignition switch to the ACC or ON

position, and then push the ON·OFF

button while the system is off to turn on

the last audio source, which was playing

immediately before the system was

turned off. While the system is on, pushing

the ON·OFF button turns the system off.

Turn the VOL control knob to adjust the

volume.
Adjusting tone quality and speaker
balance:
To adjust Bass, Treble, Balance and Fade,

push the Audio control knob. When the

display shows the setting you want to

change (Bass, Treble, Balance and Fade),

rotate the Audio control knob to set the

desired setting. For the other setting

methods, see “How to use SETTING but-

ton” (P.4-11).
This vehicle has some sound effect func-

tions as follows:
. Speed Sensitive Vol.
For more details, see “How to use SETTING

button” (P.4-11).
Switching the display:
Pushing the DISC·AUX button will switch

the displays as follows:
iPod®/USB

? CD/DVD ? Bluetooth®

Audio

? AUX ? iPod®/USB

FM-AM-SAT radio operation

radio (FM/AM) band select:

Pushing the radio band select button will

change the band as follows:
AM

? FM1 ? FM2 ? AM

radio (SAT) band select:

Pushing the radio band select button will

change the band as follows:
XM1

? XM2 ? XM3 ? XM1

When the radio band select button is

pushed while the ignition switch is in the

ACC or ON position, the radio will come

on at the channel last played.
The last channel played will also come on

when the ON·OFF button is pushed to ON.
The satellite radio is not available in

Alaska, Hawaii and Guam.
If another audio source is playing when

the radio band select button is turned to

ON, the audio source will automatically be

turned off and the last radio channel

played will come on.
When the stereo broadcast signal is weak,

the radio will automatically change from

stereo to monaural reception.

TUNE (Tuning):
. For AM and FM radio

Turn the radio TUNE knob for manual

tuning.

. For SiriusXM Satellite Radio

Turn the radio TUNE knob to seek

channels from all of the categories

when any category is not selected.

SEEK tuning/CATEGORY

(CAT):
. For AM and FM radio

Push the SEEK button

tune from low to high or high to low

frequencies and to stop at the next

broadcasting station.

. For SiriusXM Satellite Radio

Push the SEEK button

tune to the first channel of the next or

previous category.

During satellite radio reception, the fol-

lowing notices will be displayed under

certain conditions.
. NO SIGNAL (No signal is received while

the SAT tuner is connected.)

. OFF AIR (Broadcasting signed off)

. CHECK ANTENNA (Antenna connec-

tion error)

. LOADING (When the initial setting is

performed)

Center display, heater, air conditioner, audio, phone and voice recognition systems

4-53

4-54

Center display, heater, air conditioner, audio, phone and voice recognition systems

. UPDATING (When the satellite radio

subscription is not active)

SCAN tuning:

Push the SCAN tuning button to tune

from low to high frequencies and stop at

each broadcasting station/channel for 5

seconds. Pushing the button again during

this 5 seconds period will stop SCAN

tuning and the radio will remain tuned

to that station/channel.
If the SCAN tuning button is not pushed

within 5 seconds, SCAN tuning moves to

the next station/channel.

Station memory operations:

12 stations/channels can be set for the

FM band (6 each for FM1 and FM2), 18 for

SiriusXM Satellite Radio (6 each for XM1,

XM2 and XM3) and 6 stations can be set

for the AM band.
1. Choose the radio band using the radio

band select button.

2. Tune to the desired station/channel

using the SEEK/TRACK, SCAN button

or the radio TUNE knob.

3. Push and hold the desired station

preset button

until the radio

mutes.

4. The station indicator will then come

on and the sound will resume. Mem-

orizing is now complete.

5. Other buttons can be set in the same

manner.

If the battery cable is disconnected, or if

the fuse opens, the radio memory will be

erased. In that case, reset the desired

stations/channels.
List (AM and FM radio):
When the “List” key on the display is

selected while the FM or AM radio is being

played, the preset station list will be

displayed.
If 1 of the 6 preset stations listed is

touched and held, the current station will

be stored as the new preset.
Menu (SiriusXM Satellite Radio):
When the “Menu” key on the display is

selected while the SiriusXM Satellite Radio

is being played, the menu list will be

displayed.
The following items are available.
. Preset List

Displays the preset channel list. If 1 of

the 6 preset stations listed is touched

and held, the current station will be

stored as the new preset.

. Customize Channel List

Selects specific channels to skip while

using the TUNE, SEEK/CATEGORY or

Menu-Categories feature.

. Favorite Artists & Songs

Stores the current artist or song that

is being played. Touch the “Alert” key

to be reminded when the stored artist

or song is playing on a station while

listening to SiriusXM Satellite Radio.

. Categories

Selecting a category will go to the first

channel in that category as defined by

SiriusXM Satellite Radio.

. Direct Tune

Inputs the channel number by using a

keypad.

Compact Disc (CD) player operation

Push the ignition switch to the ACC or ON

position and insert the Compact Disc (CD)

into the slot with the label side facing up.

The CD will be guided automatically into

the slot and start playing.
After loading the CD, the number of

tracks on the CD and the play time will

appear on the display.
If the radio is already operating, it will

automatically turn off and the CD will

play.
If the system has been turned off while

the CD was playing, pushing the ON·OFF

button will start the CD.
Do not use 3.1 in (8 cm) discs.

PLAY:

When the DISC·AUX (CD play) button is

pushed with the system off and the CD

loaded, the system will turn on and the

CD will start to play.
When the DISC·AUX button is pushed with

the CD loaded and the radio playing, the

radio will automatically be turned off and

the CD will start to play.
Menu:
When the “Menu” key on the display is

selected while the CD is being played, the

menu screen will be displayed. The fol-

lowing menu options are available.
. Folder List (for CD with compressed

audio files)
Displays the folder list.

. Track List

Displays the track list.

. Play Mode

Select a play mode from the following

items.
— Normal
— 1 Folder Repeat (for CD with com-

pressed audio files)

— 1 Track Repeat
— 1 Disc Random
— 1 Folder Random (for CD with com-

pressed audio files)

Next/Previous Track and

Fast Forward/Rewind:
When the

button is pushed for

more than 1.5 seconds while the CD is

being played, the CD will play while fast

forwarding or rewinding. When the but-

ton is released, the CD will return to

normal play speed.
When the

button is pushed for

less than 1.5 seconds while the CD is being

played, the next track or the beginning of

the current track on the CD will be played.
When the rewind button is pushed for less

than 1.5 seconds within 3 seconds after

the current track starts playing, the pre-

vious track will be played. Push the button

several times to skip through the tracks.

REPEAT (RPT), RANDOM (RDM):

When the RPT button is pushed while the

CD is played, the play pattern can be

changed as follows:
(CD)

(CD with compressed audio files)

CD EJECT:

When the CD EJECT button is pushed with

the CD loaded, the CD will be ejected.
If the CD comes out and is not removed,

it will be pulled back into the slot to

protect it.

DVD (Digital Versatile Disc) PLAYER

OPERATION (models with naviga-

tion system)
Precautions

Start the engine when using the DVD

entertainment system.
Movies will not be shown on the front

display while the vehicle is in any drive

position to reduce driver distraction.

Audio is available when a movie is played.

To view movies in the front display, stop

the vehicle in a safe location, move the

shift lever to the P (Park) position and

apply the parking brake.

Center display, heater, air conditioner, audio, phone and voice recognition systems

4-55

4-56

Center display, heater, air conditioner, audio, phone and voice recognition systems

WARNING

. The driver must not attempt to

operate the DVD system or wear

the headphones while the vehicle

is in motion so that full attention

may be given to vehicle opera-

tion.

. Do not attempt to modify the

system to display a movie on the

front screen while the vehicle is

being driven. Doing so may dis-

tract the driver and may cause a

collision and serious personal in-

jury or death.

CAUTION

. Only operate the DVD while the

vehicle engine is running. Operat-

ing the DVD for extended periods

of time with the engine OFF can

discharge the vehicle battery.

. Do not allow the system to get

wet. Excessive moisture such as

spilled liquids may cause the

system to malfunction.

. While playing VIDEO-CD media,

this DVD player does not guaran-

tee complete functionality of all

VIDEO-CD formats.

Display settings

To adjust the front display mode, push

the SETTING button while the DVD is

being played, select the “Others” key and

then select the “Display” key.
To adjust the display ON/OFF, brightness,

tint, color and contrast, select the “Display

Adjustment” key and then select each key.
Then you can adjust each item using the

multi-function controller. After changes

have been made push the BACK button

to save the setting.

SAA2497

Playing a DVD

DISC·AUX button:
Park the vehicle in a safe location for

the front seat occupants to operate the

DVD drive while watching the images.
Push the DISC·AUX button on the instru-

ment panel and turn the display to the

DVD mode.
When a DVD is loaded, it will be replayed

automatically.
The operation screen will be turned on

when the DISC·AUX button located on the

instrument panel is pushed while a DVD is

being played, and it will turn off auto-

matically after a period of time. To turn it

on again, push the DISC·AUX button

again.
DVD operation keys:
When the DVD is playing without the

operation screen being shown, you may

use the touch screen to select items from

the displayed video. You may also use the

multifunction controller to select an item

from the displayed video. When the op-

eration screen is being shown, use the

multifunction controller or touch screen

to select an item from the displayed

menus.

PAUSE:

Select the “

” key to pause the DVD. To

resume playing the DVD, use the “PLAY”

key.

PLAY:

Select the “

” key to start playing the

DVD, for example, after pausing the DVD.

STOP:

Select the “

” key to stop playing the

DVD.

Next/Previous Chapter:

Select the “

” or “

” key to skip the

chapter(s) of the disc forward/backward.

The chapters will advance/go back the

number of times this key is selected.

Commercial Skip:

This function is only for DVD-VIDEO, DVD-

VR. Select the “

” or “

” key to skip

forward or backwards by the set amount

as defined in the DVD Settings menu.
Top Menu:
When the “Top Menu” key is selected in

the screen while a DVD is being played,

the top menu specific to each disc will be

displayed. For details, see the instructions

on the disc.

SAA2498

Example

DVD settings

Select the “Settings” key to adjust the

following settings.
Key (DVD-VIDEO):
Keys for the DVD menu operation are

displayed.

Center display, heater, air conditioner, audio, phone and voice recognition systems

4-57

4-58

Center display, heater, air conditioner, audio, phone and voice recognition systems

: Move the cursor to select a DVD

menu.

Enter:

Enter the selected menu.

Move:

Change the display location by mov-

ing the operation key.

Back:

Return to the previous screen.

Hide:

Hide the operation key.

Title Menu (DVD-VIDEO):
Some menus specific to each disc will be

shown. For details, see the instructions on

the disc.
Title Search (DVD-VIDEO, DVD-VR):
The scene with the specified title will be

displayed each time the “+” side or “−” side

is selected.
Group Search (VIDEO CD):
A scene in the specified group will be

displayed each time the “+” side or “−” side

is selected.
10 Key Search (DVD-VIDEO, VIDEO-CD,
CD-DA, DVD-VR):
Select the “10 Key Search” key to open the

number entry screen. Input the number

to be searched and select the “OK” key.

The specified Title/Chapter or Group/

Track will be played.
Select No. (VIDEO-CD):
Select the “Select No.” key to open the

number entry screen. Input the number

to be searched and select the “OK” key.

The specified scene will be played.
Angle (DVD-VIDEO):
If the DVD contains different angles (such

as moving images), the current image

angle can be switched to another one.

Select the “Angle” key. The angle will

change each time the “+” side or “−” side

is selected.
Angle Mark (DVD-VIDEO):
When this item is turned on, an angle

mark will be shown on the bottom of the

screen if the scene can be seen from a

different angle.
Menu Skip (DVD-VIDEO):
DVD menus are automatically configured

and the contents will be played directly

when the “Menu Skip” key is turned on.

Note that some discs may not be played

directly even if this item is turned on.
CM Skip (DVD-VIDEO):
Select the “CM Skip” key. Choose the

setting time from 15, 30 or 60 seconds

by selecting the “+” side or “−” side.
DRC (DVD-VIDEO, DVD-VR):
DRC (Dynamic Range Compression) auto-

matically adjusts the soundtrack volume

level to maintain a more even sound to

the speakers.

DVD Language (DVD-VIDEO, VIDEO-CD):
Select the “DVD Language” key to open

the number entry screen. Input the num-

ber corresponding to the preferred lan-

guage and select the “OK” key. The DVD

top menu language will be changed to

the one specified.
Display:
To adjust the image quality of the screen,

select the preferred adjustment items.
Audio:
Select the preferred language for audio.
Subtitle (DVD-VIDEO, DVD-VR):
Select the preferred language for sub-

titles.
Display Mode (DVD-VIDEO, VIDEO-CD,
DVD-VR):
Select from the “Full”, “Wide”, “Normal” or

“Cinema” modes.
Title List (DVD-VR):
Select the preferred title from the list.
Play Mode:
Select the preferred play mode.
PG/PL Mode (DVD-VR):
Select the “PG” or “PL” mode.

USB (Universal Serial Bus) CON-

NECTION PORT (models with navi-

gation system)
Audio main operation

WARNING

Do not connect, disconnect or oper-

ate the USB device while driving.

Doing so can be a distraction. If

distracted you could lose control of

your vehicle and cause an accident

or serious injury.

CAUTION

. Do not force the USB device into

the USB connection port. Insert-

ing the USB device tilted or up-

side-down into the port may da-

mage the port. Make sure that

the USB device is connected cor-

rectly into the USB connection

port.

. Do not grab the USB connection

port cover (if so equipped) when

pulling the USB device out of the

port. This could damage the port

and the cover.

. Do not leave the USB cable in a

place where it can be pulled

unintentionally. Pulling the cable

may damage the port.

Refer to your device manufacturer’s own-

er information regarding the proper use

and care of the device.

SAA2499

Open the console lid and connect a USB

memory as illustrated. Then, push the

DISC·AUX button repeatedly to switch to

the USB memory mode.
If the system has been turned off while

the USB memory was playing, pushing

the ON·OFF/VOL control knob will start

the USB memory.

Center display, heater, air conditioner, audio, phone and voice recognition systems

4-59

4-60

Center display, heater, air conditioner, audio, phone and voice recognition systems

SAA2500

File selection

When there are both audio and movie

files in the USB memory, the mode select

screen is displayed. Select the preferred

contents to play.
When there is only one type of file, the

audio or movie operation screen is dis-

played and starts to play.
If a video file restricts the number of

playbacks, a pop-up screen will appear

to confirm it is ok to play. Answer yes or

no as requested by the display.

SAA2501

Audio file operation

PLAY:

When the DISC·AUX button is pushed with

the system off and the USB memory

inserted, the system will turn on.
If another audio source is playing with an

USB memory inserted, push the DISC·AUX

button repeatedly until the center display

changes to the USB memory mode.

Next/Previous File and Fast

Forward/Rewind:
When the

button is pushed for

more than 1.5 seconds while a USB

memory is being played, the USB memory

will play while forwarding or rewinding.

When the button is released, the USB

memory will return to normal play speed.
When the

button is pushed for

less than 1.5 seconds while the USB

memory is being played, the next track

or the beginning of the current track on

the USB memory will be played.
When the rewind button is pushed for less

than 1.5 seconds within 3 seconds after

the current track starts playing, the pre-

vious track will be played. Push the button

several times to skip through the tracks.
The multi-function controller can also be

used to select tracks when the USB

memory is being played.
Folder selection:
To change to another folder in the USB

memory, turn the folder selector or

choose a folder displayed on the screen

using the multi-function controller.

REPEAT (RPT), RANDOM (RDM):

When the RPT button is pushed while the

USB memory is played, the play pattern

can be change as follows.
To change the play mode, push the RPT

button repeatedly and the mode will

change as follows.

Nissan 370Z (2018 year). Instruction - part 14