Nissan Altima L32. Manual - part 123

BCS-26

< FUNCTION DIAGNOSIS >

[BCM]

DIAGNOSIS SYSTEM (BCM)

*: The item is indicated, not monitored.

WIPER
WIPER : CONSULT - III Function

INFOID:0000000004202243

WORK SUPPORT

* : Factory setting

DATA MONITOR

ACTIVE TEST

FLASHER

CORNERING LAMP*

RH

—

LH

OFF

ILL DIM SIGNAL*

ON

—

OFF

Test item

Operation

Description

Service item

Setting item

Description

WIPER SPEED SET-
TING

ON

With vehicle speed
(Front wiper intermittent time linked with the vehicle speed and wiper dial position)

OFF*

Without vehicle speed
(Front wiper intermittent time linked with the wiper dial position)

Monitor Item

[Unit]

Description

PUSH SW

Displays the status of the engine switch (push switch) judged by BCM.

VEH SPEED 1
[km/h]

Displays the value of the vehicle speed signal received from combination meter with 
CAN communication.

FR WIPER HI
[OFF/ON]

Status of each switch judged by BCM using the combination switch reading function

FR WIPER LOW
[OFF/ON]

FR WASHER SW
[OFF/ON]

FR WIPER INT
[OFF/ON]

FR WIPER STOP
[OFF/ON]

Displays the status of the front wiper auto stop signal received from IPDM E/R with 
CAN communication.

INT VOLUME
[1 

− 7] 

Status of each switch judged by BCM using the combination switch reading function

Test item

Operation

Description

FRONT WIPER

HI

Transmits the front wiper request signal (HI) to IPDM E/R with CAN communication to op-
erate the front wiper HI operation.

LO

Transmits the front wiper request signal (LO) to IPDM E/R with CAN communication to 
operate the front wiper LO operation.

INT

Transmits the front wiper request signal (INT) to IPDM E/R with CAN communication to 
operate the front wiper INT operation.

OFF

Stops transmitting the front wiper request signal to stop the front wiper operation.

BCS

DIAGNOSIS SYSTEM (BCM)

BCS-27

< FUNCTION DIAGNOSIS >

[BCM]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

FLASHER : CONSULT-III Function

INFOID:0000000004202244

Work support

* : Initial setting

Data monitor

Active test

INTELLIGENT KEY
INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY)

INFOID:0000000004202246

WORK SUPPORT

Service item

Setting item

Setting

HAZARD ANSWER 
BACK

LOCK ONLY*

Activated when locking.

Sets the hazard warning lamp answer back activation 
when the door is lock/unlock with the request switch or 
the key fob.

UNLK ONLY

Activated when unlock-
ing.

LOCK/UNLK

Activated when locking/
unlocking

OFF

Not activated

Monitor item

[Unit]

Description

TURN SIGNAL R 
[ON/OFF]

Each switch condition that BCM judges from the combination switch reading function

TURN SIGNAL L 
[ON/OFF]

HAZARD SW
[ON/OFF]

The switch status input from the hazard warning switch

RKE LOCK
[ON/OFF]

The lock signal status received from the keyless receiver

RKE UNLOCK
[ON/OFF]

The unock signal status received from the keyless receiver

RKE PANIC
[ON/OFF]

The panic alarm signal status received from the keyless receiver

Test item

Operation

Description

FLASHER

RH

Blinks right turn signal lamp.

LH

Blinks left turn signal lamp.

OFF

Turns turn signal lamps (right and left) OFF.

Monitor item

Description

CONFIRM KEY FOB ID

It can be checked whether Intelligent Key ID code is registered or not in this mode.

AUTO LOCK SET

Auto door lock time can be changed in this mode.
• MODE 1: 1 minute
• MODE 2: 5 minutes
• MODE 3: 30 seconds
• MODE 4: 2 minutes

LOCK/UNLOCK BY I-KEY

Door lock/unlock function by door request switch (driver side, passenger side and trunk) mode can 
be changed to operate (ON) or not operate (OFF) with this mode. 

ENGINE START BY I-KEY

Engine start function mode can be changed to operate (ON) or not operate (OFF) with this mode.

TRUNK/GLASS HATCH OPEN

Buzzer reminder function mode by trunk opener request switch can be changed to operate (ON) 
or not operate (OFF) with this mode.

BCS-28

< FUNCTION DIAGNOSIS >

[BCM]

DIAGNOSIS SYSTEM (BCM)

SELF-DIAG RESULT

Refer to 

BCS-91, "DTC Index"

.

DATA MONITOR

PANIC ALARM SET

Panic alarm button pressing time on Intelligent Key remote control button can be selected from the 
following with this mode. 
• 0.5 sec.
• 1.5 sec.
• OFF: Non-operation

PW DOWN SET

Unlock button pressing time on Intelligent Key button to lower front windows can be selected from 
the following with this mode. 
• 3 sec.
• 5 sec.
• OFF: Non-operation

TRUNK OPEN DELAY

Trunk button pressing time on Intelligent Key button can be selected from the following with this 
mode.
• 0.5 sec.
• 1.5 sec.
• OFF: No delay

LO- BATT OF KEY FOB WARN

Intelligent Key low battery warning mode can be changed to operate (ON) or not operate (OFF) 
with this mode. 

ANTI KEY LOCK IN FUNCTI

Key reminder function mode can be changed to operate (ON) or not operate (OFF) with this mode.

HORN WITH KEYLESS LOCK

Horn reminder function mode by Intelligent Key button can be changed to operate (ON) or not op-
erate (OFF) with this mode.

HAZARD ANSWER BACK

Hazard reminder function mode can be selected from the following with this mode.
• LOCK ONLY: Door lock operation only
• UNLOCK ONLY: Door unlock operation only
• LOCK AND UNLOCK: Lock/unlock operation
• OFF: Non operation

ANS BACK I-KEY LOCK

Buzzer reminder function (lock operation) mode by door request switch (driver side and passenger 
side) can be selected from the following with this mode. 
• HORN CHIRP: Sound horn
• BUZZER: Sound Intelligent Key warning buzzer
• OFF: Non-operation

ANS BACK I-KEY UNLOCK

Buzzer reminder function (unlock operation) mode by door request switch can be changed to op-
erate (ON) or not operate (OFF) with this mode.

SHORT CRANKING OUTPUT

Starter motor can operate during the times below.
• 70 msec
• 100  msec
• 200  msec

INSIDE ANT DIAGNOSIS

This function allows inside key antenna self-diagnosis.

Monitor item

Description

Monitor Item

Condition

REQ SW-DR

Indicates [ON/OFF] condition of door request switch (driver side).

REQ SW-AS

Indicates [ON/OFF] condition of door request switch (passenger side).

REQ SW-BD/TR

Indicates [ON/OFF] condition of trunk opener request switch.

PUSH SW

Indicates [ON/OFF] condition of push button ignition switch.

IGN RLY2-F/B

Indicates [ON/OFF] condition of ignition relay 2.

ACC RLY1-F/B

Indicates [ON/OFF] condition of accessory relay.

CLUTCH SW

NOTE:
This item is displayed, but cannot be monitored. 

BRAKE SW 1

Indicates [ON/OFF] condition of brake switch.

DETE/CANCL SW

Indicates [ON/OFF] condition of P position.

SFT PN/N SW

Indicates [ON/OFF] condition of P or N position.

BCS

DIAGNOSIS SYSTEM (BCM)

BCS-29

< FUNCTION DIAGNOSIS >

[BCM]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

ACTIVE TEST

S/L -LOCK

Indicates [ON/OFF] condition of steering lock (LOCK).

S/L -UNLOCK

Indicates [ON/OFF] condition of steering lock (UNLOCK).

S/L RELAY-F/B

Indicates [ON/OFF] condition of ignition switch.

UNLK SEN-DR

Indicates [ON/OFF] condition of driver door UNLOCK status.

PUSH SW -IPDM

Indicates [ON/OFF] condition of push button ignition switch from IPDM E/R via CAN.

IGN RLY1-F/B

Indicates [ON/OFF] condition of ignition relay 1 from IPDM E/R via CAN.

DETE SW -IPDM

Indicates [ON/OFF] condition of P position from TCM via CAN.

SFT PN -IPDM

Indicates [ON/OFF] condition of P or N position from TCM via CAN.

SFT P -MET

Indicates [ON/OFF] condition of P position from TCM via CAN.

SFT N -MET

Indicates [ON/OFF] condition of N position from IPDM E/R via CAN.

ENGINE STATE

Indicates [STOP/START/CRANK/RUN] condition of engine states from ECM via CAN.

S/L LOCK-IPDM

Indicates [ON/OFF] condition of steering lock (LOCK) request from IPDM E/R via CAN.

S/L UNLOCK-IPDM

Indicates [ON/OFF] condition of steering lock (UNLOCK) request from IPDM E/R via CAN.

S/L RELAY-REQ

Indicates [ON/OFF] condition of steering lock relay from IPDM E/R via CAN.

VEH SPEED 1

Display the vehicle speed signal received from combination meter by numerical value [Km/h].

VEH SPEED 2

Display the vehicle speed signal received from ABS or VDC or CVT by numerical value [Km/h].

DOOR STAT-DR

Indicates [LOCK/READY/UNLK] condition of driver side door status.

DOOR STAT-AS

Indicates [LOCK/READY/UNLK] condition of passenger side door status.

ID OK FLAG

Indicates [SET/RESET] condition of key ID.

PRMT ENG STRT

Indicates [SET/RESET] condition of engine start possibility.

PRMT RKE STRT

NOTE:
This item is displayed, but cannot be monitored. 

KEY SW -SLOT

Indicates [ON/OFF] condition of key slot.

RKE OPE COUN1

When remote keyless entry receiver receives the signal transmitted while operating on Intelligent Key, the 
numerical value start changing.

RKE OPE COUN2

NOTE:
This item is displayed, but cannot be monitored. 

TRNK/HAT MNTR

Indicates [ON/OFF] condition of trunk lid.

RKE-LOCK

Indicates [ON/OFF] condition of LOCK signal from Intelligent Key.

RKE-UNLOCK

Indicates [ON/OFF] condition of UNLOCK signal from Intelligent Key.

RKE-TR/BD

Indicates [ON/OFF] condition of TRUNK OPEN signal from Intelligent Key.

RKE-PANIC

Indicates [ON/OFF] condition of PANIC button of Intelligent Key.

RKE-P/W OPEN

Indicates [ON/OFF] condition of P/W DOWN signal from Intelligent Key.

RKE-MODE CHG

Indicates [ON/OFF] condition of MODE CHANGE signal from Intelligent Key.

Monitor Item

Condition

Test item

Description

BATTERY SAVER

This test is able to check interior room lamp operation.
The interior room lamp will be activated after “ON” on CONSULT-III screen is touched.

PW REMOTO DOWN SET

This test is able to check power window down operation.
The power window down will be activated after “ON” on CONSULT-III screen is touched.

OUTSIDE BUZZER

This test is able to check Intelligent Key warning buzzer operation.
Intelligent Key warning buzzer sounds when “ON” on CONSULT-III screen is touched.