Nissan Altima L32. Manual - part 122

BCS-22

< FUNCTION DIAGNOSIS >

[BCM]

DIAGNOSIS SYSTEM (BCM)

ACTIVE TEST

MULTI REMOTE ENT
MULTI REMOTE ENT : CONSULT-III Function (BCM - MULTIREMOTE ENT)

INFOID:0000000004507201

DATA MONITOR

DOOR SW-DR
[ON/OFF]

The switch status input from front door switch LH

DOOR SW-AS
[ON/OFF]

The switch status input from front door switch RH

DOOR SW-RR
[ON/OFF]

The switch status input from rear door switch RH

DOOR SW-RL
[ON/OFF]

The switch status input from rear door switch LH

DOOR SW-BK
[ON/OFF]

NOTE:
The item is indicated, not monitored.

CDL LOCK SW
[ON/OFF]

Lock switch status received from central door lock switch by power window switch se-
rial link

CDL UNLOCK SW
[ON/OFF]

Unlock switch status received from central door lock switch by power window switch 
serial link

KEY CYL LK-SW
[ON/OFF]

Lock switch status received from key cylinder switch by power window switch serial 
link

KEY CYL UN-SW
[ON/OFF]

Unlock switch status received from key cylinder switch by power window switch serial 
link

TRNK/HAT MNTR
[ON/OFF]

The switch status input from trunk room lamp switch

RKE-LOCK
[ON/OFF]

Lock signal status received from remote keyless entry receiver

RKE-UNLOCK
[ON/OFF]

Unlock signal status received from remote keyless entry receiver

Monitor item

[Unit]

Description

Test item

Operation

Description

INT LAMP

ON

Outputs the interior room lamp control signal to turn map lamp and personal lamp ON 
(Map lamp switch is in DOOR position).

OFF

Stops the interior room lamp control signal to turn map lamp and personal lamp OFF.

STEP LAMP TEST

ON

Outputs the step lamp control signal to turn step lamp ON.

OFF

Stops the step lamp control signal to turn step lamp OFF.

LUGGAGE LAMP TEST

ON

Outputs the luggage room lamp control signal to turn step lamp ON.

OFF

Stops the luggage room lamp control signal to turn step lamp ON.

Monitor Item

Condition

DOOR SW-DR

Indicates [ON/OFF] condition of front door switch (driver side).

DOOR SW-AS

Indicates [ON/OFF] condition of front door switch (passenger side).

DOOR SW-RR

Indicates [ON/OFF] condition of rear door switch RH.

DOOR SW-RL

Indicates [ON/OFF] condition of rear door switch LH.

DOOR SW-BK

NOTE:
This item is displayed, but cannot be monitored. 

CDL LOCK SW

Indicates [ON/OFF] condition of door lock and unlock switch.

BCS

DIAGNOSIS SYSTEM (BCM)

BCS-23

< FUNCTION DIAGNOSIS >

[BCM]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

ACTIVE TEST

WORK SUPPORT

CDL UNLOCK SW

Indicates [ON/OFF] condition of door lock and unlock switch.

RKE-LOCK

Indicates [ON/OFF] condition of LOCK signal from keyfob.

RKE-UNLOCK

Indicates [ON/OFF] condition of UNLOCK signal from keyfob.

RKE-TR/BD

Indicates [ON/OFF] condition of TRUNK OPEN signal from keyfob.

RKE-PANIC

Indicates [ON/OFF] condition of PANIC button of keyfob.

RKE-P/W OPEN

Indicates [ON/OFF] condition of P/W DOWN signal from keyfob.

RKE-MODE CHG

Indicates [ON/OFF] condition of MODE CHANGE signal from keyfob.

KEY CYL LK-SW

Indicated [ON/OFF] condition of lock signal from door key cylinder.

KEY CYL UN-SW

Indicated [ON/OFF] condition of unlock signal from door key cylinder.

KEY CYL SW-TR

NOTE:
This item is displayed, but cannot be monitored. 

Monitor Item

Condition

Test item

Description

INT LAMP

This test is able to check interior room lamp operation.
The interior room lamp will be activated after “ON” on CONSULT-III screen is touched.

LUGGAGE LAMP TEST

NOTE:
This item is displayed, but cannot be tested.

DOOR LOCK 

This test is able to check door lock/unlock operation.
• The all door lock actuators are locked when “ALL LCK” on CONSULT-III screen is touched.
• The all door lock actuators are unlocked when “ALL UNLK” on CONSULT-III screen is 

touched.

• The door lock actuator (driver side) is unlocked when “DR UNLK” on CONSULT-III screen 

is touched.

• The door lock actuator (passenger side) is unlocked when “AS UNLK” on CONSULT- III 

screen is touched.

• The door lock actuator (rear LH and RH) is unlocked when “OTR ULK” on CONSULT-III 

screen is touched.

FLASHER

This test is able to check flasher operation [LH/RH/OFF].

HORN

This test is able to check horn operation [ON/OFF].

TRUNK/GLASS HATCH

This test is able to check trunk lid opener actuator open operation.
This actuator opens when “ON” on CONSULT-III screen is touched.

TRUNK/BACK DOOR

NOTE:
This item is displayed, but cannot be tested.

AUTOMATIC BACK DOOR 

NOTE:
This item is displayed, but cannot be tested.

Test item

Description

DOOR LOCK-UNLOCK SET

Selective unlock function mode can be changed to operate (WITH) or not operate (WITHOUT) 
with this mode.

HORN CHIRP SET

Answer back function (horn) mode can be changed in this mode.
For the detail of the setting.

HAZARD LAMP SET

Answer back function (hazard) mode can be changed in this mode.
• MODE1: Non-operation
• MODE2: Lock (non-operation) Unlock (blink once)
• MODE3: Lock (blink towice) Unlock (non-operation)
• MODE4: Lock (blink towice) Unlock (blink once) 

AUTO LOCK SET

Auto door lock time can be changed in this mode.
• MODE 1: 1 minute
• MODE 2: 5 minutes

BCS-24

< FUNCTION DIAGNOSIS >

[BCM]

DIAGNOSIS SYSTEM (BCM)

HEADLAMP
HEADLAMP : CONSULT-III Function

INFOID:0000000004202242

WORK SUPPORT

1 : Initial setting
2: With auto light system

DATA MONITOR

PANIC ALARM SET

Panic alarm button pressing time on keyfob remote control button can be selected from the 
following with this mode. 
• MODE1: 0.5 sec.
• MODE2: 1.5 sec.
• MODE3: Non-operation

PW DOWN SET

Unlock button pressing time on keyfob button can be selected from the following with this 
mode. 
• MODE 1: 3 sec.
• MODE 2: Non-operation
• MODE 3: 5 se

Test item

Description

Service item

Setting item

Setting

BATTERY SAVER SET

ON

1

With the exterior lamp battery saver function

OFF

Without the exterior lamp battery saver function

ILL DELAY SET

2

MODE 1

1

45 sec.

Sets delay timer function timer operation time
(All doors closed)

MODE 2

Without the func-
tion

MODE 3

30 sec.

MODE 4

60 sec.

MODE 5

90 sec.

MODE 6

120 sec.

MODE 7

150 sec.

MODE 8

180 sec.

CUSTOM A/LIGHT 
SETTING

2

MODE 1

1

Normal

MODE 2

More sensitive setting than normal setting (Turns ON earlier than normal operation.)

MODE 3

More sensitive setting than MODE 2 (Turns ON earlier than MODE 2.)

MODE 4

Less sensitive setting than normal setting (Turns ON later than normal operation.)

Monitor item

[Unit]

Description

PUSH SW
[ON/OFF]

The switch status input from push-button ignition switch

ENGINE STATE
[STOP/STALL/CRANK/RUN]

The engine status received from ECM with CAN communication

VEH SPEED 1
[km/h]

The value of the vehicle speed received from combination meter with CAN commu-
nication

KEY SW-SLOT
[ON/OFF]

Key switch status input from key slot

BCS

DIAGNOSIS SYSTEM (BCM)

BCS-25

< FUNCTION DIAGNOSIS >

[BCM]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

1: With auto light system.
2: The item is indicated, not monitored.

ACTIVE TEST

TURN SIGNAL R
[ON/OFF]

Each switch status that BCM judges from the combination switch reading function

TURN SIGNAL L
[ON/OFF]

TAIL LAMP SW
[ON/OFF]

HI BEAM SW
[ON/OFF]

HEAD LAMP SW1
[ON/OFF]

HEAD LAMP SW2
[ON/OFF]

PASSING SW
[ON/OFF]

AUTO LIGHT SW

1

[ON/OFF]

FR FOG SW
[ON/OFF]

DOOR SW-DR
[ON/OFF]

The switch status input from front door switch LH

DOOR SW-AS
[ON/OFF]

The switch status input from front door switch RH

DOOR SW-RR
[ON/OFF]

The switch status input from rear door switch RH

DOOR SW-RL
[ON/OFF]

The switch status input from rear door switch LH

DOOR SW-BK

2

[ON/OFF]

—

OPTICAL SENSOR
[V]

1

The value of exterior brightness voltage input from the optical sensor 

Monitor item

[Unit]

Description

Test item

Operation

Description

TAIL LAMP

ON

Transmits the Position light request signal to IPDM E/R with CAN com-
munication to turn the tail lamp ON.

OFF

Stops the tail lamp request signal transmission.

HEAD LAMP

HI

Transmits the high beam request signal with CAN communication to turn 
the headlamp (HI)

LO

Transmits the low beam request signal with CAN communication to turn 
the headlamp (LO).

OFF

Stops the high & low beam request signal transmission.

FR FOG LAMP

ON

Transmits the front fog lights request signal to IPDM E/R with CAN com-
munication to turn the front fog lamp ON.

OFF

Stops the front fog lights request signal transmission.

DAYTIME RUNNING LIGHT*

ON

—

OFF