Nissan Note E12. Manual - part 566

SEC-116

< DTC/CIRCUIT DIAGNOSIS >

B210F SHIFT POSITION/CLUTCH INTERLOCK SWITCH

Is the inspection result normal?

YES

>> Replace IPDM E/R. Refer to 

PCS-30, "Removal and Installation"

.

NO

>> Repair or replace harness.

(+)

(–)

Continuity

IPDM E/R

Connector

Terminal

F42

40

Ground

No

B2110 SHIFT POSITION/CLUTCH INTERLOCK SWITCH

SEC-117

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

B2110 SHIFT POSITION/CLUTCH INTERLOCK SWITCH

DTC Logic

INFOID:0000000009567474

DTC DETECTION LOGIC

NOTE:

If DTC B2110 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to 

BCS-

57, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Shift selector lever to the P position.

2. Turn ignition switch ON and wait 1 second or more.

3. Shift selector lever to the N position and wait 1 second or more.

4. Shift selector lever to the position other than P and N, and wait 1 second or more.

5. Check DTC in Self Diagnostic Result mode of IPDM E/R using CONSULT.
Is DTC detected?

YES

>> Go to 

SEC-117, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure 

INFOID:0000000009567475

Regarding Wiring Diagram information, refer to 

SEC-24, "Wiring Diagram"

.

1.

CHECK DTC OF BCM

Check DTC in Self Diagnostic Result mode of BCM using CONSULT.
Is DTC detected?

YES

>> Perform the trouble diagnosis related to the detected DTC. Refer to 

BCS-46, "DTC Index"

.

NO

>> GO TO 2.

2.

CHECK IPDM E/R SIGNAL CIRCUIT OPEN AND SHORT

1. Turn ignition switch OFF.

2. Disconnect IPDM E/R connector.

3. Disconnect transmission range switch connector.

4. Check continuity between IPDM E/R harness connector and transmission range switch harness connec-

tor.

5. Check continuity between IPDM E/R harness connector and ground.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B210F

INTRLCK/PNP SW OFF

IPDM E/R detects a difference between the 
following signals
• P/N position signal from transmission 

range switch and P/N position signal 
(CAN) from BCM 

• Harness or connectors

(The CAN communication line is open 
or shorted.)

• Harness or connectors

(Transmission range switch circuit is 
open or shorted.)

• Transmission range switch
• IPDM  E/R
• BCM

IPDM E/R

Transmission range switch

Continuity

Connector

Terminal

Connector

Terminal

F42

40

F52

10

Yes

SEC-118

< DTC/CIRCUIT DIAGNOSIS >

B2110 SHIFT POSITION/CLUTCH INTERLOCK SWITCH

Is the inspection result normal?

YES

>> Replace IPDM E/R. Refer to 

PCS-30, "Removal and Installation"

.

NO

>> Repair or replace harness.

(+)

(–)

Continuity

IPDM E/R

Connector

Terminal

F42

40

Ground

No

ENGINE DOES NOT START WHEN INTELLIGENT KEY IS INSIDE OF VEHICLE

SEC-119

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

SYMPTOM DIAGNOSIS

ENGINE DOES NOT START WHEN INTELLIGENT KEY IS INSIDE OF VE-
HICLE

Description

INFOID:0000000009567487

Engine does not start when push-button ignition switch is pressed while carrying Intelligent Key.

NOTE:

• Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and

check each symptom.

• The engine start function, door lock function, power distribution system, and NATS-IVIS/NVIS in the Intelli-

gent Key system are closely related to each other regarding control. The vehicle security function can oper-

ate only when the door lock and power distribution system are operating normally.

Conditions of Vehicle (Operating Conditions)

• “ENGINE START BY I-KEY” setting in “WORK SUPPORT” mode of “INTELLIGENT KEY” of “BCM” is ON.

• One or more of Intelligent Keys with registered Intelligent Key ID is in the vehicle.

Diagnosis Procedure

INFOID:0000000009567488

1.

PERFORM WORK SUPPORT

Perform “INSIDE ANT DIAGNOSIS” in “Work Support” mode of “INTELLIGENT KEY” of “BCM” using CON-

SULT.

Refer to 

BCS-21, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"

.

>> GO TO 2.

2.

PERFORM SELF-DIAGNOSIS RESULT

Select “Self Diagnostic Result” mode of “BCM”, and check whether or not DTC of inside key antenna is

detected.
Is DTC detected?

YES

>> Perform the trouble diagnosis for detected DTC. Refer to 

BCS-46, "DTC Index"

.

NO

>> GO TO 3.

3.

CHECK PUSH-BUTTON IGNITION SWITCH

Check push-button ignition switch.

Refer to 

SEC-75, "Component Inspection"

.

Is the operation normal?

YES

>> GO TO 4.

NO

>> Repair or replace malfunctioning parts.

4.

CONFIRM THE OPERATION

Confirm the operation again.
Is the inspection normal?

YES

>> Check intermittent incident. Refer to 

GI-41, "Intermittent Incident"

.

NO

>> GO TO 1.