Nissan Note E12. Manual - part 564

SEC-108

< DTC/CIRCUIT DIAGNOSIS >

B210B STARTER CONTROL RELAY

B210B STARTER CONTROL RELAY

DTC Logic

INFOID:0000000009567462

DTC DETECTION LOGIC

NOTE:

If DTC B210B is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to 

BCS-

57, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION

1. Turn ignition switch ON.

2. Turn ignition switch OFF and wait 1 second or more.

3. Turn ignition switch ON.

4. Perform Self Diagnostic Result of IPDM E/R using CONSULT.
Is DTC B210B displayed?

YES

>> Refer to 

SEC-108, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000009567463

1.

 PERFORM SELF DIAGNOSTIC RESULT

Perform Self Diagnostic Result of IPDM E/R using CONSULT.
Is display history of DTC B210B CRNT?

YES

>> Replace IPDM E/R. Refer to 

PCS-30, "Removal and Installation"

.

NO

>> Refer to 

GI-41, "Intermittent Incident"

.

CONSULT Display

DTC Detection Condition

Possible Cause

START CONT RLY ON
[B210B]

When comparing the following items, IPDM E/R 
detects that starter control relay is stuck in the 
ON position for 1 second or more.
• Starter control relay signal (CAN) from BCM
• Starter relay status signal (CAN) from BCM
• Starter control relay and starter relay status 

signal (IPDM E/R input)

• Starter control relay control signal (IPDM E/R 

output)

• Transmission range switch signal input 

IPDM E/R

B210C STARTER CONTROL RELAY

SEC-109

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

B210C STARTER CONTROL RELAY

DTC Logic

INFOID:0000000009567464

DTC DETECTION LOGIC

NOTE:

• If DTC B210C is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to

BCS-57, "DTC Logic"

.

• When IPDM E/R power supply voltage is low (Approx. 7 - 8 V for about 1 second), the DTC B210C may be

detected.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION

1. Turn ignition switch ON.

2. Turn ignition switch OFF and wait 1 second or more.

3. Turn ignition switch ON.

4. Perform Self Diagnostic Result of IPDM E/R using CONSULT.
Is DTC B210C displayed?

YES

>> Refer to 

SEC-109, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000009567465

Regarding Wiring Diagram information, refer to 

SEC-24, "Wiring Diagram"

.

1.

 PERFORM SELF DIAGNOSTIC RESULT

Perform Self Diagnostic Result of IPDM E/R using CONSULT.
Is display history of DTC B210C CRNT?

YES

>> GO TO 2.

NO

>> Refer to 

GI-41, "Intermittent Incident"

.

2.

CHECK STARTER CONTROL RELAY CONTROL CIRCUITS VOLTAGE

Check voltage between IPDM E/R connectors and ground.

Is the inspection result normal?

YES

>> Replace IPDM E/R. Refer to 

PCS-30, "Removal and Installation"

.

NO (WITH M/T)>>GO TO 3.

NO (WITH CVT)>>GO TO 4.

CONSULT Display

DTC Detection Condition

Possible Cause

STR CONT RLY OFF CIRC
[B210C]

When comparing the following items, IPDM E/R 
detects that starter control relay is stuck in the 
OFF position for 1 second or more.
• Starter control relay signal (CAN) from BCM
• Starter relay status signal (CAN) from BCM
• Starter control relay and starter relay status 

signal (IPDM E/R input)

• Starter control relay control signal (IPDM E/R 

output)

• IPDM  E/R
• BCM
• Battery

IPDM E/R

Ground

Voltage

(Approx.)

Connector

Terminal

E44 (WITH M/T)

13

—

Battery voltage

F42 (WITH CVT)

40

SEC-110

< DTC/CIRCUIT DIAGNOSIS >

B210C STARTER CONTROL RELAY

3.

CHECK STARTER CONTROL RELAY CONTROL CIRCUIT CONTINUITY

1. Disconnect IPDM E/R connector E44 and clutch interlock switch connector E34.

2. Check continuity between IPDM E/R connector E44 and clutch interlock switch connector E34.

3. Disconnect BCM connector M98.

4. Check continuity between IPDM E/R connector E44 and ground.

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-67, "Removal and Installation"

.

NO

>> Repair or replace harness or connectors.

4.

CHECK STARTER CONTROL RELAY CONTROL CIRCUIT CONTINUITY

1. Disconnect IPDM E/R connector F42 and transmission range switch connector F52.

2. Check continuity between IPDM E/R connector F42 and transmission range switch connector F52.

3. Disconnect BCM connector M98.

4. Check continuity between IPDM E/R connector F42 and ground.

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-67, "Removal and Installation"

.

NO

>> Repair or replace harness or connectors.

IPDM E/R

Clutch interlock switch

Continuity

Connector

Terminal

Connector

Terminal

E44

13

E34

2

Yes

IPDM E/R

Ground

Continuity

Connector

Terminal

E44

13

—

No

IPDM E/R

Transmission range switch

Continuity

Connector

Terminal

Connector

Terminal

F42

40

F52

10

Yes

IPDM E/R

Ground

Continuity

Connector

Terminal

F42

40

—

No

B210D STARTER RELAY

SEC-111

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

B210D STARTER RELAY

DTC Logic

INFOID:0000000009567466

DTC DETECTION LOGIC

NOTE:

If DTC B210D is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to 

BCS-

57, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION

1. Turn ignition switch ON.

2. Turn ignition switch OFF and wait 1 second or more.

3. Turn ignition switch ON.

4. Perform Self Diagnostic Result of IPDM E/R using CONSULT.
Is DTC B210D displayed?

YES

>> Refer to 

SEC-111, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000009567467

Regarding Wiring Diagram information, refer to 

SEC-24, "Wiring Diagram"

.

1.

 PERFORM SELF DIAGNOSTIC RESULT

Perform Self Diagnostic Result of IPDM E/R using CONSULT.
Is display history of DTC B210D CRNT?

YES

>> GO TO 2.

NO

>> Refer to 

GI-41, "Intermittent Incident"

.

2.

CHECK STARTER CONTROL RELAY CONTROL CIRCUITS VOLTAGE

Check voltage between IPDM E/R connectors and ground.

Is the inspection result normal?

YES

>> Replace IPDM E/R. Refer to 

PCS-30, "Removal and Installation"

.

NO (WITH M/T)>>GO TO 3.

NO (WITH CVT)>>GO TO 4.

3.

CHECK STARTER CONTROL RELAY CONTROL CIRCUIT CONTINUITY

1. Disconnect IPDM E/R connectors E44, BCM connector M98, clutch interlock switch connector E34.

CONSULT Display

DTC Detection Condition

Possible Cause

STARTER RLY ON CIRC
[B210D]

When comparing the following items, IPDM E/R 
detects that starter control relay is stuck in the 
ON position for 5 second or more.
• Starter control relay signal (CAN) from BCM
• Starter relay status signal (CAN) from BCM
• Starter control relay and starter relay status 

signal (IPDM E/R input)

• Starter control relay control signal (IPDM E/R 

output)

• Harness or connectors (starter motor relay 

control circuit open or short)

• IPDM  E/R
• BCM

IPDM E/R

Ground

Voltage

(Approx.)

Connector

Terminal

E44

13

—

Battery voltage

F42

40