Nissan Pathfinder. Manual - part 363

DLK-218

< DTC/CIRCUIT DIAGNOSIS >

TOUCH SENSOR

3. Check continuity between automatic back door control module harness connector and ground.

Is the inspection result normal?

YES

>> Replace automatic back door control module. Refer to 

DLK-321, "Removal and Installation"

.

NO

>> Repair or replace harness.

3.

CHECK TOUCH SENSOR LH GROND CIRCUIT

1. Disconnect automatic back door control module and touch sensor LH connector.

2. Check continuity between automatic back door control module harness connector and touch sensor LH

harness connector.

3. Check continuity between automatic back door control module harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK TOUCH SENSOR LH GROND CIRCUIT 2

1. Connect automatic back door control module and touch sensor LH connector.

2. Check voltage between automatic back door control module harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace harness.

5.

CHECK TOUCH SENSOR LH

Refer to 

DLK-219, "LH : Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Replace touch sensor LH. Refer to 

DLK-309, "TOUCH SENSOR : Removal and Installation"

.

6.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-49, "Intermittent Incident"

.

>> Inspection End.

Automatic back door control module

Touch sensor LH 

Continuity 

 Connector

Terminal

 Connector

Terminal

B55

2

D556

1

Yes

Automatic back door control module

Ground

Continuity 

 Connector

Terminal

B55

2

No

Automatic back door control module

Touch sensor LH

Continuity 

 Connector

Terminal

Connector

Terminal

B55

13

D556

2

Yes

Automatic back door control module

Ground

Continuity 

 Connector

Terminal

B55

13

No

(+)

(–)

Voltage

(Approx.)

Automatic back door control module

 Connector

Terminal

B55

13

Ground

0.01 – 0 V

TOUCH SENSOR

DLK-219

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

LH : Component Inspection

INFOID:0000000009175781

1.

CHECK TOUCH SENSOR LH

1. Turn ignition switch OFF.

2. Disconnect touch sensor LH connector.

3. Check resistance between touch sensor LH terminals.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Replace touch sensor LH. Refer to 

DLK-309, "TOUCH SENSOR : Removal and Installation"

.

Touch sensor LH

 Condition

Resistance 

(Approx.)

Terminal

1

2

Touch sensor LH

Detect obstruction

380 – 420 k

Ω

Other than above

0.95 – 1.05 k

Ω

DLK-220

< DTC/CIRCUIT DIAGNOSIS >

SPINDLE MOTOR

SPINDLE MOTOR

RH
RH : Diagnosis Procedure

INFOID:0000000009175782

Regarding Wiring Diagram information, refer to 

DLK-94, "Wiring Diagram"

.

1.

CHECK SPINDLE MOTOR INPUT SIGNAL

1. Turn ignition switch OFF.

2. Disconnect spindle unit RH connector.

3. Check voltage between spindle unit RH harness connector and ground.

Is the inspection result normal?

YES

>> Replace spindle unit RH. Refer to 

DLK-296, "SPINDLE UNIT : Removal and Installation"

.

NO

>> GO TO 2.

2.

CHECK SPINDLE MOTOR CIRCUIT

1. Disconnect automatic back door control module connector.

2. Check continuity between automatic back door control module harness connector and spindle unit har-

ness connector. 

3. Check continuity between automatic back door control module harness connector and ground.

Is the inspection result normal?

YES

>> Replace automatic back door control module. Refer to 

DLK-321, "Removal and Installation"

.

NO

>> Repair or replace harness.

LH
LH : Diagnosis Procedure

INFOID:0000000009175783

Regarding Wiring Diagram information, refer to 

DLK-94, "Wiring Diagram"

.

1.

CHECK SPINDLE MOTOR INPUT SIGNAL

1. Turn ignition switch OFF.

(+)

(–)

Condition

Voltage

(Approx.)

Spindle unit RH

Connector

Terminal

B162

9

Ground

Back door

Auto open opera-

tion

16.75 – 8.5 V

2

Auto close opera-

tion

Automatic back door control module

Spindle unit RH

Continuity 

Connector

Terminal

Connector

Terminal

B56

29

B162

9

Yes

36

2

Automatic back door control module

Ground

Continuity 

Connector

Terminal

B56

29

No

36

SPINDLE MOTOR

DLK-221

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

2. Disconnect spindle unit LH connector.

3. Check voltage between spindle unit LH harness connector and ground.

Is the inspection result normal?

YES

>> Replace spindle unit LH. Refer to 

DLK-296, "SPINDLE UNIT : Removal and Installation"

.

NO

>> GO TO 2.

2.

CHECK SPINDLE MOTOR CIRCUIT

1. Disconnect automatic back door control module connector.

2. Check continuity between automatic back door control module harness connector and spindle unit LH

harness connector. 

3. Check continuity between automatic back door control module harness connector and ground.

Is the inspection result normal?

YES

>> Replace automatic back door control module. Refer to 

DLK-321, "Removal and Installation"

.

NO

>> Repair or replace harness.

(+)

(–)

Condition

Voltage

(Approx.)

Spindle unit LH

Connector

Terminal

B70

9

Ground

Back door

Auto open opera-

tion

16.75 – 8.5 V

2

Auto close opera-

tion

Automatic back door control module

Spindle unit LH

Continuity 

Connector

Terminal

Connector

Terminal

B56

27

B70

9

Yes

34

2

Automatic back door control module

Ground

Continuity 

Connector

Terminal

B56

27

No

34