Murano Cross Cabriolet Z51 (2012 year). Manual - part 88

 

  Index      Manuals     Murano Cross Cabriolet Z51 (2012 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     86      87      88      89     ..

 

 

Murano Cross Cabriolet Z51 (2012 year). Manual - part 88

 

 

SRC-48

< DTC/CIRCUIT DIAGNOSIS >

B1037, B1039, B1041 CRASH ZONE SENSOR

B1037, B1039, B1041 CRASH ZONE SENSOR

DTC Logic

INFOID:0000000007564609

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1.

Turn ignition switch ON.

2.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

 Without CONSULT

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-13, "On Board Diagnosis Function"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-48, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000007564610

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes

or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

1.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connectors.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace wiring harness.

3.

REPLACE CRASH ZONE SENSOR

1.

Replace crash zone sensor. Refer to 

SR-26, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-48, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4.

NO

>> INSPECTION END

4.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-30, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-48, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1.

DTC

Display contents of 

CONSULT

DTC detecting condition

Possible cause

B1037
B1039
B1041

CRASH ZONE SENS1 

Crash zone sensor is malfunctioning

• Malfunction in crash zone sensor
• Malfunction in air bag diagnosis sensor unit

Revision: 2013 February

2012 Murano CrossCabriolet

B1037, B1039, B1041 CRASH ZONE SENSOR

SRC-49

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

NO

>> INSPECTION END

Revision: 2013 February

2012 Murano CrossCabriolet

SRC-50

< DTC/CIRCUIT DIAGNOSIS >

B1042, B1043, B1044, B1045, B1046, B1047 DIAGNOSIS SENSOR UNIT

B1042, B1043, B1044, B1045, B1046, B1047 DIAGNOSIS SENSOR UNIT

DTC Logic

INFOID:0000000007564611

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1.

Turn ignition switch ON.

2.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

 Without CONSULT

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-13, "On Board Diagnosis Function"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-50, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000007564612

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes

or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

1.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connectors.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace wiring harness.

3.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-30, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-50, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1.

NO

>> INSPECTION END

DTC

Display contents of 

CONSULT

DTC detecting condition

Possible cause

B1042
B1043
B1044
B1045
B1046
B1047

CONTROL UNIT 

Air bag diagnosis sensor unit is malfunctioning

Malfunction in air bag diagnosis sensor unit

Revision: 2013 February

2012 Murano CrossCabriolet

B1049, B1054 DRIVER AIR BAG MODULE

SRC-51

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

B1049, B1054 DRIVER AIR BAG MODULE

DTC Logic

INFOID:0000000007564613

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1.

Turn ignition switch ON.

2.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

 Without CONSULT

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-13, "On Board Diagnosis Function"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?

YES

>> Refer to 

SRC-51, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000007564614

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes

or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

1.

CHECK HARNESS CONNECTOR

Check the harness connector.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace wiring harness.

3.

CHECK SPIRAL CABLE CIRCUIT 

1.

Turn ignition switch OFF.

2.

Disconnect driver air bag module harness connector and combination switch (spiral cable) harness con-
nector.

3.

Check continuity between driver air bag module harness connector and combination switch (spiral cable)
harness connector.

DTC

Display contents of 

CONSULT

DTC detecting condition

Possible cause

B1049
B1054

DRIVER AIRBAG 
MODULE
[OPEN]

Driver air bag module circuit is open
(including the spiral cable)

• Harness or connectors

(The module circuit is open.)

• Malfunction in driver air bag module
• Malfunction in spiral cable
• Malfunction in air bag diagnosis sensor unit

Revision: 2013 February

2012 Murano CrossCabriolet

SRC-52

< DTC/CIRCUIT DIAGNOSIS >

B1049, B1054 DRIVER AIR BAG MODULE

4.

Check continuity between driver air bag module harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Replace combination switch (spiral cable). Refer to 

SR-14, "Exploded View"

.

4.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-30, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-51, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 5.

NO

>> INSPECTION END

5.

REPLACE DRIVER AIR BAG MODULE

1.

Replace driver air bag module. Refer to 

SR-11, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-51, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1.

NO

>> INSPECTION END

Driver air bag module

Combination switch (spiral cable)

Continuity 

Connector

Terminal

Connector

Terminal

M350

10

M32

28

Existed

11

30

M351

12

29

9

30

Driver side air bag module

Ground

Continuity 

Connector

Terminal

M350

10

Not existed

11

M351

12

9

Revision: 2013 February

2012 Murano CrossCabriolet

B1050, B1055 DRIVER AIR BAG MODULE

SRC-53

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

B1050, B1055 DRIVER AIR BAG MODULE

DTC Logic

INFOID:0000000007564615

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1.

Turn ignition switch ON.

2.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

 Without CONSULT

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-13, "On Board Diagnosis Function"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-53, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000007564616

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes

or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

1.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace wiring harness.

3.

REPLACE SPIRAL CABLE

1.

Replace combination switch (spiral cable). Refer to 

SR-14, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-53, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4.

NO

>> INSPECTION END

4.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-30, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-53, "DTC Logic"

.

DTC

Display contents of 

CONSULT

DTC detecting condition

Possible cause

B1050
B1055

DRIVER AIRBAG 
MODULE 
[VB-SHORT]

Driver air bag module circuit is shorted to 
power supply circuit
(including the spiral cable)

• Harness or connectors

(The module circuit is shorted.)

• Malfunction in driver air bag module
• Malfunction in spiral cable
• Malfunction in air bag diagnosis sensor unit

Revision: 2013 February

2012 Murano CrossCabriolet

SRC-54

< DTC/CIRCUIT DIAGNOSIS >

B1050, B1055 DRIVER AIR BAG MODULE

Is DTC detected?

YES

>> GO TO 5.

NO

>> INSPECTION END

5.

REPLACE DRIVER AIR BAG MODULE

1.

Replace driver air bag module. Refer to 

SR-11, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-53, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1.

NO

>> INSPECTION END

Revision: 2013 February

2012 Murano CrossCabriolet

B1051, B1056 DRIVER AIR BAG MODULE

SRC-55

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

B1051, B1056 DRIVER AIR BAG MODULE

DTC Logic

INFOID:0000000007564617

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1.

Turn ignition switch ON.

2.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

 Without CONSULT

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-13, "On Board Diagnosis Function"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?

YES

>> Refer to 

SRC-55, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000007564618

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes

or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

1.

CHECK HARNESS CONNECTOR

Check the harness connector.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace wiring harness.

3.

CHECK SPIRAL CABLE CIRCUIT 

1.

Turn ignition switch OFF.

2.

Disconnect driver air bag module harness connector and combination switch (spiral cable) harness con-
nector.

3.

Check continuity between driver air bag module harness connector and combination switch (spiral cable)
harness connector.

DTC

Display contents of 

CONSULT

DTC detecting condition

Possible cause

B1051
B1056

DRIVER AIRBAG 
MODULE 
[GND-SHORT]

Driver air bag module circuit is shorted to ground
(including the spiral cable)

• Harness or connectors

(The module circuit is shorted.)

• Malfunction in driver air bag module
• Malfunction in spiral cable
• Malfunction in air bag diagnosis sensor unit

Revision: 2013 February

2012 Murano CrossCabriolet

SRC-56

< DTC/CIRCUIT DIAGNOSIS >

B1051, B1056 DRIVER AIR BAG MODULE

4.

Check continuity between driver air bag module harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Replace combination switch (spiral cable). Refer to 

SR-14, "Exploded View"

.

4.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-30, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-55, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 5.

NO

>> INSPECTION END

5.

REPLACE DRIVER AIR BAG MODULE

1.

Replace driver air bag module. Refer to 

SR-11, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-55, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1.

NO

>> INSPECTION END

Driver air bag module

Combination switch (spiral cable)

Continuity 

Connector

Terminal

Connector

Terminal

M350

10

M32

28

Existed

11

30

M351

12

29

9

30

Driver side air bag module

Ground

Continuity 

Connector

Terminal

M350

10

Not existed

11

M351

12

9

Revision: 2013 February

2012 Murano CrossCabriolet

B1052, B1057 DRIVER AIR BAG MODULE

SRC-57

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

B1052, B1057 DRIVER AIR BAG MODULE

DTC Logic

INFOID:0000000007564619

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1.

Turn ignition switch ON.

2.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

 Without CONSULT

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-13, "On Board Diagnosis Function"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?

YES

>> Refer to 

SRC-57, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000007564620

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes

or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

1.

CHECK HARNESS CONNECTOR

Check the harness connector.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace wiring harness.

3.

CHECK SPIRAL CABLE CIRCUIT-I

1.

Turn ignition switch OFF.

2.

Disconnect driver air bag module harness connector and combination switch (spiral cable) harness con-
nector.

3.

Check continuity between combination switch (spiral cable) terminals.

DTC

Display contents of 

CONSULT

DTC detecting condition

Possible cause

B1052
B1057

DRIVER AIRBAG 
MODULE 
[SHORT]

Driver air bag module circuit are shorted to each 
other
(including the spiral cable)

• Harness or connectors

(The module circuit is shorted.)

• Malfunction in driver air bag module
• Malfunction in spiral cable
• Malfunction in air bag diagnosis sensor unit

Revision: 2013 February

2012 Murano CrossCabriolet

SRC-58

< DTC/CIRCUIT DIAGNOSIS >

B1052, B1057 DRIVER AIR BAG MODULE

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Replace combination switch (spiral cable). Refer to 

SR-14, "Exploded View"

.

4.

CHECK SPIRAL CABLE CIRCUIT-II

Check continuity between combination switch (spiral cable) terminals.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Replace combination switch (spiral cable). Refer to 

SR-14, "Exploded View"

.

5.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-30, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-57, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 6.

NO

>> INSPECTION END

6.

REPLACE DRIVER AIR BAG MODULE

1.

Replace driver air bag module. Refer to 

SR-11, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-57, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1.

NO

>> INSPECTION END

Combination switch (spiral cable)

Continuity 

Connector

Terminal

Connector

Terminal

M350

10

M350

11

Not existed

M351

9

12

Combination switch (spiral cable)

Continuity 

Connector

Terminal

Terminal

M32

28

29

Not existed

30

Revision: 2013 February

2012 Murano CrossCabriolet

B1058, B1059, B1060, B1061, B1062, B1063 DIAGNOSIS SENSOR UNIT

SRC-59

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

B1058, B1059, B1060, B1061, B1062, B1063 DIAGNOSIS SENSOR UNIT

DTC Logic

INFOID:0000000007564621

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1.

Turn ignition switch ON.

2.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

 Without CONSULT

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-13, "On Board Diagnosis Function"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-59, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000007564622

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes

or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

1.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connectors.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace wiring harness.

3.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-30, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-59, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1.

NO

>> INSPECTION END

DTC

Display contents of 

CONSULT

DTC detecting condition

Possible cause

B1058
B1059
B1060
B1061
B1062
B1063

CONTROL UNIT 

Air bag diagnosis sensor unit is malfunctioning

Malfunction in air bag diagnosis sensor unit

Revision: 2013 February

2012 Murano CrossCabriolet

SRC-60

< DTC/CIRCUIT DIAGNOSIS >

B1065, B1070 PASSENGER AIR BAG MODULE

B1065, B1070 PASSENGER AIR BAG MODULE

DTC Logic

INFOID:0000000007564623

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1.

Turn ignition switch ON.

2.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

 Without CONSULT

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-13, "On Board Diagnosis Function"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-60, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000007564624

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

1.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace wiring harness.

3.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-30, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-60, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4.

NO

>> INSPECTION END

4.

REPLACE PASSENGER AIR BAG MODULE

1.

Replace passenger air bag module. Refer to 

SR-17, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-60, "DTC Logic"

.

Is DTC detected?

DTC

Display contents of 

CONSULT

DTC detecting condition

Possible cause

B1065
B1070

ASSIST A/B MODULE 
[OPEN]

Passenger air bag module circuit is open

• Harness or connectors

(The module circuit is open.)

• Malfunction in passenger air bag module
• Malfunction in air bag diagnosis sensor unit

Revision: 2013 February

2012 Murano CrossCabriolet

B1065, B1070 PASSENGER AIR BAG MODULE

SRC-61

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

YES

>> GO TO 1.

NO

>> INSPECTION END

Revision: 2013 February

2012 Murano CrossCabriolet

SRC-62

< DTC/CIRCUIT DIAGNOSIS >

B1066, B1071 PASSENGER AIR BAG MODULE

B1066, B1071 PASSENGER AIR BAG MODULE

DTC Logic

INFOID:0000000007564625

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1.

Turn ignition switch ON.

2.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

 Without CONSULT

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-13, "On Board Diagnosis Function"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-62, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000007564626

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

1.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace wiring harness.

3.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-30, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-62, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4.

NO

>> INSPECTION END

4.

REPLACE PASSENGER AIR BAG MODULE

1.

Replace passenger air bag module. Refer to 

SR-17, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-62, "DTC Logic"

.

Is DTC detected?

DTC

Display contents of CON-

SULT

DTC detecting condition

Possible cause

B1066
B1071

ASSIST A/B MODULE 
[VB-SHORT]

Passenger air bag module circuit is 
shorted to power supply circuit

• Harness or connectors

(The module circuit is shorted.)

• Malfunction in passenger air bag module
• Malfunction in air bag diagnosis sensor unit

Revision: 2013 February

2012 Murano CrossCabriolet

B1066, B1071 PASSENGER AIR BAG MODULE

SRC-63

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

YES

>> GO TO 1.

NO

>> INSPECTION END

Revision: 2013 February

2012 Murano CrossCabriolet

 

 

 

 

 

 

 

Content      ..     86      87      88      89     ..