Murano Cross Cabriolet Z51 (2012 year). Manual - part 87

 

  Index      Manuals     Murano Cross Cabriolet Z51 (2012 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     85      86      87      88     ..

 

 

Murano Cross Cabriolet Z51 (2012 year). Manual - part 87

 

 

SRC-32

< DTC/CIRCUIT DIAGNOSIS >

B1017, B1020, B1021 OCCUPANT SENS C/U

B1017, B1020, B1021 OCCUPANT SENS C/U

DTC Logic

INFOID:0000000007564591

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1.

Turn ignition switch ON.

2.

Perform “AIR BAG” Self Diagnostic Result with CONSULT.

 Without CONSULT

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-13, "On Board Diagnosis Function"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-32, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000007564592

WARNING:

Always observe the following items for preventing accidental activation.
• Before servicing, turn power switch OFF, disconnect battery negative terminal, and wait 3 minutes or

more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

DIAGNOSTIC PROCEDURE

1.

CHECK HARNESS CONNECTOR

Check the connection of harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connectors.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace wiring harness.

3.

REPLACE OCCUPANT CLASSIFICATION SYSTEM CONTROL UNIT

1.

Replace passenger seat cushion assembly. Refer to 

SR-33, "Removal and Installation"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-32, "DTC Logic"

.

Is DTC detected?

YES

>>  GO TO 4.

NO

>> INSPECTION END

4.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-30, "Removal and Installation"

.

DTC

Display contents of 

CONSULT

DTC detecting condition

Possible cause

B1017
B1020
B1021

OCCUPANT SENS C/U 
[UNIT FAIL]

Occupant Classification System control 
unit is malfunctioning

• Disconnection of wiring harness
• Malfunction in Occupant Classification System 

control unit

• Malfunction in air bag diagnosis sensor unit

Revision: 2013 February

2012 Murano CrossCabriolet

B1017, B1020, B1021 OCCUPANT SENS C/U

SRC-33

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

2.

Perform DTC confirmation procedure. Refer to 

SRC-32, "DTC Logic"

.

Is DTC detected?

YES

>>  GO TO 1.

NO

>> INSPECTION END

Revision: 2013 February

2012 Murano CrossCabriolet

SRC-34

< DTC/CIRCUIT DIAGNOSIS >

B1018 OCCUPANT SENS

B1018 OCCUPANT SENS

DTC Logic

INFOID:0000000007564593

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1.

Turn ignition switch ON.

2.

Perform “AIR BAG” Self Diagnostic Result with CONSULT.

 Without CONSULT

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-13, "On Board Diagnosis Function"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-34, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000007564594

WARNING:

Always observe the following items for preventing accidental activation.
• Before servicing, turn power switch OFF, disconnect battery negative terminal, and wait 3 minutes or

more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

DIAGNOSTIC PROCEDURE

1.

CHECK HARNESS CONNECTOR

Check the connection of harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connectors.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace wiring harness.

3.

REPLACE OCCUPANT CLASSIFICATION SYSTEM CONTROL UNIT

1.

Replace passenger seat cushion assembly. Refer to 

SR-33, "Removal and Installation"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-34, "DTC Logic"

.

Is DTC detected?

YES

>>  GO TO 4.

NO

>> INSPECTION END

4.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-30, "Removal and Installation"

.

DTC

Display contents of 

CONSULT

DTC detecting condition

Possible cause

B1018

OCCUPANT SENS 
[UNIT FAIL]

Occupant Classification System 
sensor is malfunctioning

• Disconnection of wiring harness
• Malfunction in Occupant Classification System sensor
• Malfunction in Occupant Classification System control unit
• Malfunction in air bag diagnosis sensor unit

Revision: 2013 February

2012 Murano CrossCabriolet

B1018 OCCUPANT SENS

SRC-35

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

2.

Perform DTC confirmation procedure. Refer to 

SRC-34, "DTC Logic"

.

Is DTC detected?

YES

>>  GO TO 1.

NO

>> INSPECTION END

Revision: 2013 February

2012 Murano CrossCabriolet

SRC-36

< DTC/CIRCUIT DIAGNOSIS >

B1022 OCCUPANT SENS C/U

B1022 OCCUPANT SENS C/U

DTC Logic

INFOID:0000000007564595

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1.

Turn ignition switch ON.

2.

Perform “AIR BAG” Self Diagnostic Result with CONSULT.

 Without CONSULT

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-13, "On Board Diagnosis Function"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?

YES

>> Refer to 

SRC-36, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000007564596

WARNING:

Always observe the following items for preventing accidental activation.
• Before servicing, turn power switch OFF, disconnect battery negative terminal, and wait 3 minutes or

more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

DIAGNOSTIC PROCEDURE

1.

CHECK HARNESS CONNECTOR

Check the connection of harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connectors.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace wiring harness.

3.

REPLACE OCCUPANT CLASSIFICATION SYSTEM CONTROL UNIT

1.

Replace passenger seat cushion assembly. Refer to 

SR-33, "Removal and Installation"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-36, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4.

NO

>> INSPECTION END

4.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-30, "Removal and Installation"

.

DTC

Display contents of 

CONSULT

DTC detecting condition

Possible cause

B1022

OCCUPANT SENS C/U 
[COMM FAIL]

Malfunction occurs in Occupant Classifica-
tion System control unit, circuit between 
Occupant Classification System control 
unit and Air bag diagnosis sensor unit

• Disconnection of wiring harness
• Malfunction in Occupant Classification System 

control unit

• Malfunction in air bag diagnosis sensor unit

Revision: 2013 February

2012 Murano CrossCabriolet

B1022 OCCUPANT SENS C/U

SRC-37

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

2.

Perform DTC confirmation procedure. Refer to 

SRC-36, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1.

NO

>> INSPECTION END

Revision: 2013 February

2012 Murano CrossCabriolet

SRC-38

< DTC/CIRCUIT DIAGNOSIS >

B1023 PASSENGER AIR BAG OFF INDICATOR

B1023 PASSENGER AIR BAG OFF INDICATOR

DTC Logic

INFOID:0000000007564597

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1.

Turn ignition switch ON.

2.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

 Without CONSULT

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-13, "On Board Diagnosis Function"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-38, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000007564598

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes

or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

DIAGNOSTIC PROCEDURE

1.

CHECK HARNESS CONNECTOR

Check the connection of harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connectors.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace wiring harness.

3.

CHECK PASSENGER AIR BAG OFF INDICATOR

1.

Replace cluster lid C (passenger air bag OFF indicator). 

2.

Perform DTC confirmation procedure. Refer to 

SRC-38, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4.

NO

>> INSPECTION END

4.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-30, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-38, "DTC Logic"

.

DTC

Display contents of 

CONSULT

DTC detecting condition

Possible cause

B1023

PASS A/B INDCTR CKT 
[UNIT FAIL]

Passenger air bag OFF indicator circuit 
is open or shorted to ground or the cir-
cuits are shorted each other

• Harness or connectors
• Malfunction in passenger air bag OFF indicator
• Malfunction in air bag diagnosis sensor unit

Revision: 2013 February

2012 Murano CrossCabriolet

B1023 PASSENGER AIR BAG OFF INDICATOR

SRC-39

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

Is DTC detected?

YES

>> GO TO 1.

NO

>> INSPECTION END

Revision: 2013 February

2012 Murano CrossCabriolet

SRC-40

< DTC/CIRCUIT DIAGNOSIS >

B1025, B1032, B1048 OCS SENSOR

B1025, B1032, B1048 OCS SENSOR

DTC Logic

INFOID:0000000007564599

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1.

Turn ignition switch ON.

2.

Perform “AIR BAG” Self Diagnostic Result with CONSULT.

 Without CONSULT

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-13, "On Board Diagnosis Function"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-40, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000007564600

WARNING:

Always observe the following items for preventing accidental activation.
• Before servicing, turn power switch OFF, disconnect battery negative terminal, and wait 3 minutes or

more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

DIAGNOSTIC PROCEDURE

1.

CHECK HARNESS CONNECTOR

Check the connection of harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connectors.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace wiring harness.

3.

REPLACE OCCUPANT CLASSIFICATION SYSTEM CONTROL UNIT

1.

Replace passenger seat cushion assembly. Refer to 

SR-33, "Removal and Installation"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-40, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4.

NO

>> INSPECTION END

4.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-30, "Removal and Installation"

.

DTC

Display contents of 

CONSULT

DTC detecting condition

Possible cause

B1025
B1032
B1048

OCS SENSOR 

Malfunction occurs in Occupant Classifica-
tion System control unit, circuit between 
Occupant Classification System control 
unit and Air bag diagnosis sensor unit

• Disconnection of wiring harness
• Internal breakdown in Occupant Classification 

System control unit

• Malfunction in air bag diagnosis sensor unit

Revision: 2013 February

2012 Murano CrossCabriolet

B1025, B1032, B1048 OCS SENSOR

SRC-41

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

2.

Perform DTC confirmation procedure. Refer to 

SRC-40, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1.

NO

>> INSPECTION END

Revision: 2013 February

2012 Murano CrossCabriolet

SRC-42

< DTC/CIRCUIT DIAGNOSIS >

B1026, B1027, B1028, B1029, B1030, B1031 DIAGNOSIS SENSOR UNIT

B1026, B1027, B1028, B1029, B1030, B1031 DIAGNOSIS SENSOR UNIT

DTC Logic

INFOID:0000000007564601

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1.

Turn ignition switch ON.

2.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

 Without CONSULT

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-13, "On Board Diagnosis Function"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-42, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000007564602

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes

or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

1.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connectors.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace wiring harness.

3.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-30, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-42, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1.

NO

>> INSPECTION END

DTC

Display contents of 

CONSULT

DTC detecting condition

Possible cause

B1026
B1027
B1028
B1029
B1030
B1031

CONTROL UNIT 

Air bag diagnosis sensor unit is malfunctioning

Malfunction in air bag diagnosis sensor unit

Revision: 2013 February

2012 Murano CrossCabriolet

B1033, B1034 CRASH ZONE SENSOR

SRC-43

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

B1033, B1034 CRASH ZONE SENSOR

DTC Logic

INFOID:0000000007564603

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1.

Turn ignition switch ON.

2.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

 Without CONSULT

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-13, "On Board Diagnosis Function"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-43, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000007564604

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes

or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

1.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connectors.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace wiring harness.

3.

REPLACE CRASH ZONE SENSOR

1.

Replace crash zone sensor. Refer to 

SR-26, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-43, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4.

NO

>> INSPECTION END

4.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-30, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-43, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1.

DTC

Display contents of

CONSULT

DTC detecting condition

Possible cause

B1033
B1034

CRASH ZONE SEN 
[UNIT FAIL]

Crash zone sensor is malfunctioning

• Harness or connectors
• Malfunction in crash zone sensor
• Malfunction in air bag diagnosis sensor unit

Revision: 2013 February

2012 Murano CrossCabriolet

SRC-44

< DTC/CIRCUIT DIAGNOSIS >

B1033, B1034 CRASH ZONE SENSOR

NO

>> INSPECTION END

Revision: 2013 February

2012 Murano CrossCabriolet

B1035 CRASH ZONE SENSOR

SRC-45

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

B1035 CRASH ZONE SENSOR

DTC Logic

INFOID:0000000007564605

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1.

Turn ignition switch ON.

2.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

 Without CONSULT

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-13, "On Board Diagnosis Function"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-45, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000007564606

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes

or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

1.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connectors.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace wiring harness.

3.

REPLACE CRASH ZONE SENSOR

1.

Replace crash zone sensor. Refer to 

SR-26, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-45, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4.

NO

>> INSPECTION END

4.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-30, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-45, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1.

DTC

Display contents of 

CONSULT

DTC detecting condition

Possible cause

B1035

CRASH ZONE SEN 
[COMM FAIL]

Crash zone sensor is malfunctioning or out of 
the specified specification

• Harness or connectors
• Malfunction in crash zone sensor
• Malfunction in air bag diagnosis sensor unit

Revision: 2013 February

2012 Murano CrossCabriolet

SRC-46

< DTC/CIRCUIT DIAGNOSIS >

B1035 CRASH ZONE SENSOR

NO

>> INSPECTION END

Revision: 2013 February

2012 Murano CrossCabriolet

B1036 CRASH ZONE SENSOR

SRC-47

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

B1036 CRASH ZONE SENSOR

DTC Logic

INFOID:0000000007564607

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1.

Turn ignition switch ON.

2.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

 Without CONSULT

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-13, "On Board Diagnosis Function"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-47, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000007564608

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes

or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

1.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connectors.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace wiring harness.

3.

REPLACE CRASH ZONE SENSOR

1.

Replace crash zone sensor. Refer to 

SR-26, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-47, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4.

NO

>> INSPECTION END

4.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-30, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-47, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1.

NO

>> INSPECTION END

DTC

Display contents of 

CONSULT

DTC detecting condition

Possible cause

B1036

CRASH ZONE SEN 
[UNMATCH]

Crash zone sensor is out of the specified speci-
fication

Diagnosis sensor unit or crash zone sensor is 
different from the part specified

Revision: 2013 February

2012 Murano CrossCabriolet

 

 

 

 

 

 

 

Content      ..     85      86      87      88     ..